Home

JetPress 12 Manual.p65

1. clockwise and wait for the press to come up to heat The Heating Light will be lit while heating When the thermometer indicates the desired temperature turn the temperature knob back to the left counter clockwise slowly until the red heating light turns off The Heating light will continually cycle on and off to regulate your tem perature setting afterwards and the machine may be pressed whether lit or not 4 The Digital Timer is set by using the M S buttons Hold them down to increase values rapidly Press the Start Stop button to start the timer When the alarm sounds press the Start Stop button again to reset Important Notes 1 Always leave Heat Platen in Up Unclamped position when not pressing Pro longed contact with the silicone pad will decrease the life of the pad Do not leave press Heating Unattended or for extremely long periods of time 3 Do not let power cord come in contact with heat platen 4 Silicone pad may be slightly larger than heat platen or may expand due to heat This is normal 5 Heat platen may pivot slightly back and forth rotationally This is due to move ment allowance within the clamp assembly and is normal Pressing 1 Lift up on the handle to open the press The press should always be in the open position when the press is heating Swing the heat platen out away from the rubber pad 2 Lay out T Shirt or other item to be printed as desired Lay transfer paper onto shirt Be sure the
2. ONE YEAR LIMITED WARRANTY Geo Knight amp Co warrants that the press is free from defects in both material and workmanship from the date of invoice to the buyer If any parts or workmanship are found to be defective in manufacture Geo Knight amp Co will repair or replace the defective parts or workman ship This limited one 1 year warranty covers all parts and labor to repair the defects except when damage results from accident alteration misuse or abuse or when machine has been improperly installed or modified in any way If the press becomes defective during the limited warranty period of one year Geo Knight amp Co reserves the right to recall the defective press to the factory for repairs A return authorization must be granted by Geo Knight amp Co prior to its return If a press covered by the one year limited warranty must be returned to the factory for repairs Geo Knight amp Co shall make every effort to repair buyer s press However Geo Knight amp Co reserves the exclusive right to determine whether to repair or replace a defective press If Geo Knight amp Co authorizes a replacement press the warranty of the replacement press shall expire on the anniversary date of the original machine s invoice to the buyer There are no warranties which extend beyond the description on the face hereof Seller disclaims any implied warranty of merchantability and or any implied warranty of fitness for a particular purpose and buye
3. Transfer Paper is well within the silicone pad pressing area 3 Adjust the pressure knob clockwise to increase pressure and counter clockwise to decrease pressure Do not turn the knob counter clockwise too far or the swivel arm will disconnect from the machine frame 4 Bring the handle down clamping the press and press the Start Stop button on the Digital Timer The handle should lock firmly in place and should point straight forward 5 Consult the Transfer Paper instructions on whether to peel cold ot hot Here are suggested pressing time guidlines for different transfer papers Ink Jet Transfer Paper fabrics 14 18 seconds Laser Copier Printer Transfer Paper fabrics 18 25 seconds Sublimation Transfers onto Fabrics 25 30 seconds Sublimation Transfers onto FR Plastic Woods 60 70 seconds 6 Mousepads coasters and other thicker matierals may also be pressed Simply adjust the pressure adjustment knob as stated in step 2 7 To avoid re heating the first transfer when printing double sided T Shirts insert a sheet of cardboard in between the shirt adjust the height to less pressure amp press Troubleshooting 1 Transfer is pressed print side up and transfer image is burned onto the heat platen surface Unplug press swing heat platen out to allow room to clean Use strong detergent and non abrasive scrubbing sponge to remove transfer material from heat platen 2 Heat Platen becomes severely misaligned with silicone
4. pad There is a stop adjust ment at the back of the swivel post This is adjustable with an allen key Loosen the stop bracket at the back of the press swing the press in the desired stop postion and tighten the allen key Make sure the stop bracket is pushed hard against the stop post while tightening ALSO Loosen top nut connecting heat platen to clamp shaft Lower heat platen but do not clamp Rotate heat platen until square with silicone pad and let go to be sure heat platen is relaxed and in proper alignment Clamp the heat platen down fully Tighten top nut very tightly to lock heat platen position 3 Press continuously heats up far beyond normal operating temperature and red light does not turn off The thermostat has failed Call factory to obtain new thermostat and follow instruc tions for replacement
5. r agrees that the goods are sold as is Geo Knight amp Co does not warrant that the functions of the press will meet the buyers requirements or expecta tions The entire risk as to use quality and performance of the press lies with the buyer In no event will Geo Knight amp Co be liable for any damages including loss of profits destruction of goods or any other special incidental consequential or indirect damages arising from the use of the press or accompanying materials This limitation will apply even if Geo Knight amp Co or its authorized agent has been advised of the possibility of such damage This product is not intended for business or professional use and all warranties above are considered null and void if this product is used in a production or manufacturing environment or in a continuous volume capacity as defined by Geo Knight amp Co Geo Knight amp Co Inc 52 Perkins St Brockton MA 02302 USA 508 588 0186 Fax 508 587 5108 info heatpress com www heatpress com 4 JETPRESS 12 JETPRESS 12 Pra Pressure Knob Digital Timer Power Socket On Off Switch Heating Light Clamp amp Handle Thermometer Pa rad Thermostat Knob Start Up 1 Connect power cord to the press Plug the cord into the power socket in the back of the control console and then into the wall receptacle 2 Turn the power on by flipping the On Off Switch on 3 Turn the Thermostat Knob to the right

JetPress 12 Manual.p65

Contents

Download Pdf Manuals

Related Search

Related Contents