PROFESSIONAL LOUDSPEAKER SYSTEM
Contents
1. _ Montarbo IN Montarbo IN Y WIDE YY G NO 2 SYSTEM S DESCRIPTION a WIDE15P compression driver 1 4 throat 2 5 voice coil featuring a neodymium magnet and titanium diaphragm and loaded by a 80 x 60 wave guide horn WIDE12P compression driver 1 throat 2 5 voice coil featuring a neodymium magnet and titanium diaphragm and loaded by a a 80 x 60 wave guide horn b WIDE15P 15 woofer featuring a 3 voce coil and a powerful external neodymium magnet WIDE12P 12 woofer featuring a 3 voce coil and a powerful external neodymium magnet c Cabinet made from birch plywood with high impact chip resistant paint d Steel protection grill with foam protection e Bass reflex vent f Three carrying handles g Controls and connections panel h 2 anti slip adjustable feet for use as a stage monitor i Speaker stand adapter l M10 threaded inserts CONNECTION PANELS 1 Input Speakon connector IN Connect it to the power amplifier or to the powered mixer output See connection examples at pages 19 20 2 Input link Speakon connector LINK Wired in parallel to the input connector making it possible to drive another parallel connected speaker system Always pay attention to the total impedance see page 17 NOTE Connector 2 is not installed on models with 4 ohm rated impedance WIDE15P4 and WIDE2. woofers with ventilated high flux neodymium magnets and long excursion large diameter voice coils controlled directivity wave guide horns coupled to neodymium drivers with very high magnetic flux The portability has been optimized all systems may be carried and installed by a single person Very high levels of performance despite their remarkably small size and low weight 1 2 APPLICATIONS WIDE15P and WIDE12P speakers systems may be used with any power amplifier or powered mixer of adequate quality and power output 750 W ElAJ is suggested for each speaker but they work best with the PLM3000 powered loudspeaker controller PLM3000 features a built in DSP loudspeaker controller and four power amplifiers each rated at 750 W 4 ohm It can effortlessly drive four 4 ohm systems WIDE15P4 or WIDE12P4 or eight 8 ohm systems WIDE15P8 or WIDE15P8 The factory presets of the internal controller include those designed for the WIDE series speaker systems in a variety of different applications front of house or stage monitor and configurations stereo system or 4 independent channels It also includes advanced features such as a full parametric equalizer and delay and noise gate controls ensuring optimal system set up Montarbo JJ ENGLISH Fi WI DERZ user s manual WIDE WIDEIJSZI WIDE WIDE ies SERIES O i eb Y WIDE Z
3. by most other manufacturers For 3 parallel connected systems the resulting total impedance decreases to 2 7 ohm and for 4 system to 2 ohm A If the speakers are rated at 4 ohm impedance then this 2 ohm limit is reached by simply wiring two of them in parallel Some power amplifiers and powered mixers cannot operate reliably with these low values of load impedance Always check the technical specifications of your amplifier or powered mixer for the value of the minimum load impedance A 4 3 PRODUCT CARE AND MAINTENANCE To avoid malfunctions and premature degrading of specifications e Never expose the loudspeaker for long periods to direct sunlight e Never expose the loudspeaker to heat sources such as radiators or other products that produce heat e Never expose the loudspeaker to excessive vibrations or mechanical shocks e Avoid operating and storing the enclosure in damp or dusty places this may lead to malfunctions and premature degrading of specifications e Care should be taken so that objects do not fall and liquid are not spilled into the enclosure In public event don t let people musicians technicians or anyone put glasses cups ashtrays or cigarettes on the enclosure e Use a soft brush or a jet of air to clean the enclosure Do not use alcohol solvents or detergents e Always leave the protective grille mounted on the enclosure e Take care of your connecting cables Make sure that they are n
4. make sure that stability is guaranteed by matching the upper loudspeaker feet to the lower loudspeaker cavities To avoid shocks kicks or whatever action always reserve a protected area with no access to unqualified personnel as installation site of the product In case the product is used near children and animals closest supervision is necessary This product can generate very high acoustic pressures which are dangerous for the hearing system Always avoid operation at loud levels if anyone is excessively near to the product at least 1 m of distance Never expose children to high sound sources PACKAGE CONTENTS WIDE15P4 WIDE15P8 or WIDE12P4 WIDE12P8 Owner s manual Warranty certificate CE declaration of conformity ENGLISH Montarbo T WIDE SERIES WI D EIZ W DE Ws W DE Ikiz WIDE user s manual 1 INTRODUCTION AND APPLICATIONS 1 1 INTRODUCTION WIDE15P and WIDE12P feature a revolutionary new concept in acoustic and electronic design characterized by painstaking attention in terms of component selection materials and production techniques The result is a product of absolutely contemporary essential and rigorous design with great attention to detail All the system s drivers designed with great attention to every detail and custom built specifically for these systems are equipped with the most efficient and powerful motor assemblies available on the market today
5. 12P4 Use only loudspeaker cables unscreened having suitable cross section at least 2 x 1 5 mm and quality Do not twist or sharply bend the cables and do not allow for knots to be formed because they may result in insulation damage Do not use shielded cables microphone signal cables For detailed instructions about connector wiring see par 3 2 A Never connect two power amplifiers to the same speaker system this could cause serious damage to the amplifiers A ENGLISH Montarbo T WIDE WI D EAZ SERIES WIDE WI D EIZ WI DE IJt user s manual 20 mm WIRES CABLE 2 WIRES CABLE CHUCK BUSHING ME FERRULES FOR STRANDS 3 INSERT e 2 asa INSIDE VIEW 1 SETSCREWS HOUSING SPEAKON CONNECTOR 3 INSTALLATION AND WIRING 3 1 INSTALLATION Make sure that the installation position is a protected one so that the cables cannot be trampled or tripped on Make sure that the shape and load rating of the mounting surface are suitable for a safe installation If the system is placed over a surface make sure that the cables are placed in a protected position to avoid the risk of the speakers falling over if somebody trips over them The WIDE15P WIDE12P speak
6. ES WIDE WIDEIBE nad fA EXAMPLE 3 STAGE MONITOR system with PLM3000 powered processor and 4 WIDE 15P4 12P4 systems PLM3000 preset 5 EXAMPLE 4 stereo RO H system with PLM3000 powered processor and 4 WIDE 15P4 12P4 systems PLM3000 preset 6 PLM3000 PLm3000 O OULU Montarbo OJ Le informazioni contenute in questo manuale sono state attentamente redatte e controllate Tuttavia non si assume alcuna responsabilit per eventuali inesattezze Questo manuale non pu contenere una risposta a tutti i singoli problemi che possono presentarsi durante l installazione e l uso dell apparecchio Siamo a vostra disposizione per fornirvi eventuali ulteriori informazioni e consigli La Elettronica Montarbo srl non pu essere ritenuta responsabile per danni o incidenti a cose o persone causati o connessi all utilizzazione o malfunzionamento dell apparecchio Caratteristiche dati tecnici e immagini possono essere modificati senza preavviso The information contained in this manual have been carefully drawn up and checked However no responsibility will be assumed for any incorrectness This manual cannot cover all the possible contingencies which may arise during the product installation and use Should further information be desired please contact us or our local distributor S F R S Elettronica Montarbo srl can not be consid
7. Users private households In the European Union Attention If you want to dispose of this equipment please do not use the ordinary dust bin Used electrical and electronic equipment should not be disposed of via the normal household waste stream but must be treated separately and in accordance with legislation that requires proper treatment recovery and recycling of used electrical and electronic equipment Following the implementation by member states private households within the EU states may return their used electrical and electronic equipment to designated collection facilities free of charge In some countries your local retailer may also take back your old product free of charge if you purchase a similar new one Please contact your local authority for further details In other Countries outside the EU If you wish to dispose of this product please contact your local authorities and ask for the correct method of disposal In Switzerland Used electrical or electronic equipment can be returned free of charge to the dealer even if you don t purchase a new product Further collection facilities are listed on the homepage of www swico ch or www sens ch Information on Disposal for Professional Users In the European Union If the product is used for business purposes and you want to discard it please contact your Montarbo dealer who will inform you about the take back of the product You might be charged for the costs arising from take back a
8. WIDE SERIES WIDE el WIDE II WI D E IAZ WI D E It PROFESSIONAL LOUDSPEAKER SYSTEM WIDEIAZI WIDEISZI WIDE user s manual WIDEJIMZ WIDE JJ SERIES The exclamation point in an equilateral triangle is intended to alert the user to the presence A of important operating and maintenance instructions in the literature accompanying the l N D E X product 1 INTRODUCTION AND APPLICATIONS 9 IMPORTANT Safety instructions 1 1 Introduction 9 WARNING 1 2 Applications 9 In order to protect your own and others safety and to avoid invalidation of the warranty of this product please read this section 2 SYSTEM S DESCRIPTION 10 carefully before operating this product This product has been designed and manufactured to be operated as a speaker 3 INSTALLATION AND WIRING 11 system in the typical applications of a sound reinforcement system or of a sound 3 1 Installation 11 recording system Operation for purposes other than these is not provided for by the e manufacturer and is therefore to be undertaken at the end user s and or installer s sole 3 2 Wiring of SPEAKON connector 11 risk and responsability TO AVOID THE RISK OF DAMAGE 4 IMPORTANT 12 e Never expose this product to rain or moisture never use it in proximity of water or in high humidity conditions Never let any liquid as well as any object penetrate the 4 1 Connection to the input sockets 12 product Should this be the case do not use the speaker system and
9. echnical elastomer material W 436 x H 730 x D 395 mm 30 8 Kg Waste from Electrical and Electronic Equipment Attention WIDE12P4 4 ohm WIDE12P8 8 ohm Custom designed to Montarbo specifications 12 woofer 3 voice coil with external neodymium magnet external neodymium magnet compression driver 1 4 throat 2 5 voice coil with neodymium magnet and titanium diaphragm wide dispersion 80 H x 60 V wave guide horn 1400 Hz WIDE12P4 1 Neutrik Speakon WIDE12P8 2 Neutrik Speakon Birch plywood anti abrasion paint steel protection grille with external foam 2 adjustable feet that enable the use as variable angle stage monitors 10 threaded studs M10 for safe and simple suspension Adapter for a supporting pole 3 transport handles made of a special technical elastomer material W 366 x H 590 x D 377 mm 24 5 Kg The crossed out wheeled bin symbol that can be found on this product means that the product is covered by the Waste from Electrical and Electronic Equipment Directive The symbol is intended to indicate that waste from electrical and electronic equipment must be subject to a selective collection For more details on available collection facilities please contact your local government office or the retailer where you purchased this product The solid bar underneath indicates that the product has been put on the market after 13th August 2005 INFORMATION ON PROPER DISPOSAL Information on Disposal for
10. er system may be placed over standard speaker supports stand by means of built in adapter i page 13 The M10 thresed inserts l page 13 are intended for fixed installation by means of standard or custom made mounting accessories For a safe installation is mandatory that these accessories are specified to safely support the speaker weight It is the installer s responsibility to verify that the installation s safety has not been compromised When used as stage monitors the exclusive adjustable anti slip feet allow to adjust the tilt angle A 3 2 WIRING OF THE CONNECTION CABLE TO THE SPEAKON CONNECTOR 1 Strip the cable for 20 mm of length and strip each wire for 8 mm of length We suggest to use a cable with 2 x 1 5 mm section wires the insert terminals are however suitable for a cable with wires up to a section of 4mm 12AWG 2 Insert the cable into the bushing and into the chuck white chuck for a cable diameter of 5 11mm black chuck for a cable outer diameter of 9 50 15mm Fit a ferrule at the end of each wire and connect wires on the insert 3 The wire ends can be clamped in the terminals using a PZ1 screwdriver or soldered Always pay attention to the symbols shown on the connector body connect the positive wire to the terminal labelled 1 the negative wire to the terminal labelled 1 Terminals 2 and 2 are not used 4 After connecting the wires to the insert lead it through the body and
11. ered responsible for damages which may be caused to people and things when using this product Specifications features and pictorial material are subject to change without prior notice WIDEISZI WIDER WIDEIAZI WI DEAR PROFESSIONAL LOUDSPEAKER SYSTEM Elettronica Montarbo srl 40057 Cadriano Bologna Italy 39 051 766437 e Fax 39 051 765226 on ar 10 mail montarbo com e www montarbo com Made in Italy
12. nd recycling Small products and small amounts might be taken back by your local collection facilities In Spain Please contact the established collection system or your local authority for takeback of your used products In other Countries outside the EU please contact your local authorities and ask for the correct method of disposal Montarbo JJ ENGLISH WIDENAZI WIDEISZI WIDE gt user s manual WIDEIAZI WIDEISZ SERIES 6 APPLICATIONS EXAMPLE 1 MBR12FXP Powerd mixer and 2 WIDE15P4 WIDE12P4 systems 0000000000600 00689 90 0 0 0 0 0 0 0 0 0 0 0 0 0 Gogg 0000000000000 08990 0000000000060 6 6 6 4 6 8 4 6 4 865 O bb bbb be be ee eS 92 EEEE EEEE EEE alalela a s ala Gla G a gon Ge s 6 a e e e e ma De Ca e Ge 8 Ce Ce De e Ce ee Lee ots bts bi Die bia Lia La De OFS Lau ca OFF DU EE fae a rare dala rale 0 61 EEE EEE TEE E EEE Eh acesso ss 410 101816 6 8 0 8 0 6 06L6 L8l ge om om om pe om dm pm Om om om Om om om EXAMPLE 2 Four channel F O H GENERAL PURPOSE system with PLM3000 powered processor and 4 WIDE 15P4 12P4 systems PLM3000 PRESET 4 PLM3000 o PLm3000 Montarbo JJ WIDE WIDER WIDEISZI SERI
13. ot damaged knotted or twisted e Do not force connectors e Before performing any connection make certain that the power amplifier or the powered mixer are switched off ENGLISH Montarbo JJ WIDE WIDEWZY WIDER SERIES WIDENAZIO W DE tees user s manual 5 TECHNICAL DATA SPECIFICATIONS WIDE15P4 WIDE15P8 WIDE12P4 WIDE12P8 Enclosure 2 way bass reflex 2 way bass reflex Frequency response 50 20 000 Hz 60 20 000 Hz Sensitivity 100 dB SPL 1W 1m 98 dB SPL O 1W 1m SPL max 132 dB 130 dB Nominal Power 400 W AES 400 W AES Power handling 1600 W PEAK 1600 W PEAK Recommended amplifier 750 W EIAJ 750 W EIAJ Impedance e Components LF HF e Cross over e Connections WIDE15P4 4ohm WIDE15P8 8 ohm Custom designed to Montarbo specifications 15 woofer 3 voice coil with external neodymium magnet compression driver 1 4 throat 2 5 voice coil with neodymium magnet and titanium diaphragm wide dispersion 80 H x 60 V wave guide horn 90 rotatable 1200 Hz WIDE15P4 1 Neutrik Speakon WIDE15P8 2 Neutrik Speakon PHYSICAL SPECIFICATIONS e Construction e Fittings e Dimensions Weight Birch plywood anti abrasion paint steel protection grille with external foam 2 adjustable feet that enable the use as variable angle stage monitors 10 threaded studs M10 for safe and simple suspension Adapter for a supporting pole 3 transport handles made of a special t
14. refer to qualified 4 2 Parallel connection of 2 or more systems 12 servicing before operating it again Never place burning candles or other sources of E open flame on top of the device 4 3 Product care and maintenance 12 e This product must be connected only to the output of a power amplifier or a powered mixer Always use a good quality speaker cable unscreened and check 5 TECHNICAL DATA 13 it frequently for any damage to insulation and connectors e Before attempting to move the product after it has been installed remove all 6 APPICATIONS 14 15 the connections e Before moving the product after it has been installed or while it is operating make sure that the power amplifier is switched off e To disconnect this product from connecting cable never pull the cable directly hold it by the plug instead CAUTION This product does not contain user serviceable parts To prevent fire and or electrical shock never disassemble it or remove the rear panel For maintenance and servicing always refer to the official Montarbo Distributor in your Country or to qualified personnel specifically authorised by the Distributor Before placing the product on a surface of any kind make sure that its shape and load rating safely match the product size and weight When installing the speaker system on a stand use a stable stand that will fit in the adapter and may carry the loudspeaker weight When two loudspeakers are laid one upon the other
15. screw down the body with the bushing Mating connector is a Neutrik Speakon model NL4 FC Montarbo JJ ENGLISH Pi WI DEIZ WI D E WS user s manual WIDEIJSZI WIDE WIDE ies SERIES 4 IMPORTANT A 4 1 CONNECTION TO THE INPUT SOCKETS e Use only loudspeaker cables unscreened having suitable cross section at least 2 x 1 5 mm and quality Do not twist or sharply bend the cables and do not allow for knots to be formed because they may result in insulation damage A 4 2 PARALLEL CONNECTION OF 2 OR MORE SYSTEMS IMPORTANT models WIDE 153P4 and 123P4 with 4 ohm rated impedance are not intended for parallel connection to avoid damages to the power amplifier see following paragraph Only in the case that the power amplifier is rated for 2 ohm operation it is possible to parallel connect two 4 ohm speakers to one amplifier channel wiring them directly to the amplifier output connectors with two separate cables one each speaker e Connect the IN socket of the second system to the LINK socket of the second one Please note that IN and LINK sockets are wired in parallel thus both of them may be used as input or output indifferently e PAY SPECIAL ATTENTION TO THE PARALLEL IMPEDANCE if two 8 ohm systems are parallel connected the resulting load impedance for the amplifier will be 4 ohm a value that is within the allowed range for all power amplifiers and powered mixers manufactured by Montarbo and
Download Pdf Manuals
Related Search