CYWM6934 WirelessUSB LS(TM) Radio Module
Contents
1. Contains Transmitter Module FCC ID XYZMODEL1 or Contains FCC ID XYZMODEL 1 Any similar wording that expresses the same meaning may be used a No co location with other transmitters is allowed By definition co location is when another radio or its antenna is located within 20 cm of our radio and it can transmit simultaneously with your radio Only the antenna s that were certified with your radio may be used Other antennas may be used only if they are of the same type e g yagi dipole patch and have the same or lower gain 9 Not withstanding the Modular Approval for the Radio Device with associated interconnect and antennae the end product configuration must meet digital emissions compliance and must be tested in accordance with FCC Document No 38 16012 Rev C Part 15 requirements confirming radiated emissions are within specified limits Applicable sections include m Part 15 Section 15 109 Sub paragraph A Class B Radiated Emission Limits These emissions tests can be conducted by the manufacturer or by contacting an approved test facility equipped and certified accordingly The results of these emissions tests are not required to be submitted to the FCC or Cypress but should be kept on file by the OEM a Cypress module can only be installed by the OEM and not by the user It should not be installed in a user accessible ocation 9 Any modifications to the radio will void the user s authority to ope2. 8 CG p o iz HC 6 wat tf CD D o mo tow ie s C8 O tm sa amp O Document No 38 16012 Rev C Page 6 of 9 r c cO gt O PERFORM Figure 4 CYWM6934 Schematic Y ITDOIM LLNV psd ZZ AOL PAN OL e sA19 ZHN EL HUZZ 1 LI GO 69N 89N Z N 99N S N VON ON ON LON dd ONI ola IYAOIG 1NOE LX EX NIELX TLOVd INO Nia gt Ip Ip Ip O po DONA 7 7 HHI LN il 0318 PE6JISNMAD DOA GduU Dal A QA ssu LASAYU DOA WIZ ZLYOH Page 7 of 9 Document No 38 16012 Rev C 7 CYPRESS CYWM6934 PERFORM Ordering Information Table 2 Ordering Information Part Number Package Name Package Type Operating Range This document is subject to change and may be found to contain errors of omission or changes in parameters For feedback or technical support regarding Cypress WirelessUSB products please contact Cypress at www cypress com WirelessUSB LS is a trademark of Cypress Semiconductor Corporation All product and company names mentioned in this document are the trademarks of their respective holders Document No 38 16012 Rev C Page 8 of9 F CYPRESS CYWM6934 PERFORM Document History Page Document Title CYWM6934 WirelessUSB LSTM Radio Module Document Number 38 16012 Orig of mer ECN NO Description of Change 329977 See EON Bon Now datashest OOOO A 508598
3. See EON UYR Added Modular Cetficaton detalls For the USA the EU and Canada e 3346223 onson HEMP Template update a I Cypress Semiconductor Corporation 2005 2014 The information contained herein is subject to change without notice Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product Nor does it convey or imply any license under patent or other rights Cypress products are not warranted nor intended to be used for medical life support life saving critical control or safety applications unless pursuant to an express written agreement with Cypress Furthermore Cypress does not authorize its products for use as critical components in life support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user The inclusion of Cypress products in life support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges Any Source Code software and or firmware is owned by Cypress Semiconductor Corporation Cypress and is protected by and subject to worldwide patent protection United States and foreign United States copyright laws and international treaty provisions Cypress hereby grants to licensee a personal non exclusive non transferable license to copy use modify create derivative works of and compile the Cypress Sourc
4. 1 Applications m PC human interface devices HID 3 Mice aq Keyboards q Joysticks m Peripheral gaming devices a Game controllers 9 Console keyboards m General 9 Presenter tools a Remote controls a Consumer electronics 9 Barcode scanners a POS peripherals o Toys PCB Trace Antenna CYWUSB6934 2 0 pF 2 0 pF 3 3 nH 1 RFIN RFOUT WirelessUSB LS 2 2 nH 27 pF CYWUSB6934 Silicon Cypress Semiconductor Corporation Document No 38 16012 Rev C 198 Champion Court 13MHz Crystal San Jose CA 95134 1709 408 943 2600 Revised October 23 2014 S37 CYPRESS CYPRESS PERFORM Reference Documentation For information on technical details of the WirelessUSB LS 2 4 GHz DSSS Radio SoC such as register settings timing application interfaces clocking and power management see the datasheet of the CYWUSB6934 Radio SoC Applications Support The CYWM6934 is available as a reference design complete with PCB layout files schematics and a bill of materials The CYWM6934 can be used with the CY3635 WirelessUSB N 1 sensor development kit and the CY3632 WirelessUSB LS development kit via a 1 x 14 adaptor board Module Certification Details Eligibility Requirements for Regulatory Module Approval The CYWM6934 LS Radio Module is a device that transmits and receives radio signals in accordance with the spectrum regulations for the
5. for Japan TELEC must be acquired through typical approval procedures These approvals are the sole responsibility of the OEM Note Even with modular approval the end device still has to be tested for digital emissions compliance with all agencies as an electronic device The modular approval only eliminates the need to test for compliance on RF transmissions 1 This list is as of march 2006 Please talk to your local Sales person for the current list Document No 38 16012 Rev C Page 2 of 9 a CYPRESS PERFORM CYWM6934 User Guide Information Electronic device manufacturers using Cypress s Modular Approval are required to follow the below mentioned labeling practice on the container in that the device is marketed or in the product user s guide This should be in accompaniment with other regulatory information The text may be disbursed according to language or geographic regions if desired but the exact text shown below must be maintained United States of America requirements The device shall bear the following statement in a conspicuous location This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation When the device is so small or for such use that it is not pr
6. in the R amp TTE Directive corrections of non compliance issues are the responsibility of the end product manufacturer Criteria for Modular Approval In our OEM instructions it is recommend that the following rules required by ETSI be adhered to a No co location with other transmitters is allowed By definition co location is when another radio or its antenna is located within 20 cm of our radio and it can transmit simultaneously with your radio Only the antenna s that were certified with your radio may be used Other antennas may be used only if they are of the same type e g yagi dipole patch and have the same or lower gain 9 The end product configuration must meet digital emissions compliance and must be tested in accordance with the European Union standards ETSI 300 328 European Telecommunications Standard for 2 4 GHz ISM band Emissions and ETSI 300 826 Electromagnetic Compatibility Detailed European Union regulatory standards documents may be obtained from the following url http europa eu int comm enterprise rtte infor htm These emissions tests can be conducted by the manufacturer or by contacting an approved test facility equipped and certified accordingly The results of these emissions tests are not required to be submitted to the ETSI or Cypress but should be kept on file by the OEM a Cypress module can only be installed by the OEM and not Dai NG user It should not be installed in a user accessible
7. not visible when the module is installed inside another device then the outside of the device into that the module is installed must also display a label referring to the enclosed module This exterior label can use wording such as the following Contains Transmitter Module Canadian Cert No IC XYZMODEL1 or Contains Canadian Cert No IC XYZMODEL 1 Any similar wording that expresses the same meaning may be used a No co location with other transmitters is allowed By definition co location is when another radio or its antenna is located within 20 cm of our radio and it can transmit simultaneously with your radio Only the antenna s that were certified with your radio may be used Other antennas may be used only if they are of the same type e g yagi dipole patch and have the same or lower gain 9 Notwithstanding the Modular Approval for the Radio Device with associated interconnect and antennae the Page 3 of 9 a Ee ange SF Cypress CYPRESS PERFORM end product configuration must meet digital emissions compliance and must be tested in accordance Industry Canada RSS 210 Low Power License Exempt Radio communication Devices requirements confirming radiated tl are within specified limits Applicable sections include m Part 15 Section 15 109 Sub paragraph A Class B Radiated Emission Limits These emissions tests can be conducted by the manufacturer or by contacting an approved
8. ocation 9 Any modifications to the radio will void the user s authority to operate the equipment The OEM must not modify any aspect of the radio s mechanical and electrical configuration a The OEM must include compliance information in their user information a Although no additional regulatory work may be required for the radio the host device is probably subject to other FCC authorizations as a digital device DoC authorization is required for PCs and peripherals verification is required for most other digital devices Note The European Union generally follows the guidelines of the FCC for emissions level requirements FCC end product compliance certification results if available may be used to satisfy EU requirements Substitution Method Please consult the ETSI 300 328 specifications to confirm inter agency compliance If comparable FCC testing has not been performed or if the specifications are not cross compliant ETSI 300 328 testing will be required Additionally testing to the ETSI 301 489 17 immunity testing is strongly recommended Cypress assumes no responsibility for compliance of the end product configuration Page 4 of 9 CYPRESS CYWM6934 PERFORM Product Labeling Requirements the use restrictions of the end product i e countries disallowing European Union product labeling requirements stipulate specific the operating frequencies of the CYWM6934 text be placed on the device containing the CYWM6
9. respective holders
10. test facility equipped and certified accordingly The results of these emissions tests are not required to be submitted to Industry Canada or Cypress but should be kept on file by the OEM a Cypress module can only be installed by the OEM and not by f user It should not be installed in a user accessible ocation 9 Any modifications to the radio will void the user s authority to operate the equipment The OEM must not modify any aspect of the radio s mechanical and electrical configuration a The OEM must include compliance information in their user information 3 Although no additional regulatory work may be required for the radio the host device is probably subject to other FCC authorizations as a digital device DoC authorization is required for PCs and peripherals verification is required for most other digital devices Note Industry Canada generally follows the guidelines of the FCC for emissions level requirements FCC end product compliance certification results may be used to satisfy Industry Canada requirements Please consult the Industry Canada RSS 210 specifications to confirm interagency compliance If comparable FCC testing has not been performed or if the specifications are not cross compliant RSS 210 testing will be required Product Labeling Requirements Industry Canada productlabeling requirements stipulate specific text be placed on the device containing the CYWM6934 module The product label must includ
11. 2 4 GHz unlicensed frequency range Regional regulatory agency approval may be required to operate CYWM6934 throughout the world Cypress Semiconductor Corporation has obtained regulatory approvals for the CYWM6934 to be used in specific countries CYWM6934 was approved under the Modular Approval MA Grant This certification represents a significant cost savings to the OEM The MA Grant provides that device manufacturers who incorporate CYWM6934 as tested and approved can be relieved from having to perform the Radio Regulatory certification portion of the respective agency certification The MA Grant is valid only in countries that recognize the MA Grant certification process the USA Canada Belgium Denmark France Finland Germany Italy Netherlands Spain Sweden UK In order to be able to take advantage of Cypress s modular certification in an end product the following must be ensured 1 Correct Application 2 Correct Installation 3 Correct labeling Correct Application There are three types of application considered for wireless modules and the LS has been verified to work with all three application types at pre certified power output levels However other usages are possible with re certification The application types are defined as follows 0 0 0 1 Fixed Application Module is in a permanent location and has atleast 2 m separation from the human body 0 0 0 2 Mobile Application Module can be reloc
12. 934 module Note The product label must include the following text and must be Th _ l be labeled CE and to the riahtofthe CE affixed to the exterior of the OEM s product As shown in the Ee PASAN a aah 4 s Sua The gt Correct Labeling section 4 1 3 This same information may be exclamation mark designates a non harmonized frequency included in the product user manual however this is not band mandatory Packaging and user documentation must indicate Pin Definitions Table 1 Pin Description Table for the CYWM6934 pman sme a est je l gt m T Supply voltage for the entire Radio Module 2 7 V 3 6 V It is recommended that 3 3 V be used for most pron 3 m ouu Jinerupsignal rom Rado Medue io Re NOY RESET put pte set sial om Moona 6 most npu aster out save in SPI sgnal am MCU t Bado Meade U e 988 ro Active tow slave select signal ram MCU Radowo oooO e mso Output astern save out SPI sonal tom Rado Mode CU SSCS eo Gp e e On mwe mwem OOOO 2 NO women OOOO Figure 1 CYWM6934 Header Pin out 12 pin 2mm header GND VCC IRQ nRESET MOSI nSS SCK MISO GND nPD N C N C Document No 38 16012 Rev C Page 5 of 9 Gyenrss CYWM6934 PERFORM Figure 2 CYWM6934 Mechanical Drawing V20 Unit Mils O 9179 Figure 3 CYWM6934 Top View E M CH LZ CACI E s maat 12 pin 2 mm P mani ipang gt Header s Pin 1 gt Wo a i R HE ol fi
13. Features m The CYWM6934 LS 2 4 GHz DSSS Radio SoC Module includes radio CYWUSB6934 antenna and all external components m Complete radio module with PCB trace antenna m Operates in the unlicensed Industrial Scientific and Medical ISM band 2 4 GHz 2 483 GHz m 90 dBm receive sensitivity m Up to 0 dBm output power m Range of up to 10 meters or more m Data throughput of up to 62 5 kbits sec m SPI microcontroller interface up to 2 MHz data rate m Operating voltage from 2 7 V to 3 6 V m Small PCBA Design 0 975 24 38 mm by 0 65 16 25 mm by 0 212 5 3 mm L x W x H m FCC modular approval grant to meet FCC Part 15 EN 300 328 1 EN 301 489 1 and Industry Canada RSS 210 standards m An FCC module approval MA Grant provides customers significant cost savings by allowing customers to adopt the CYWM6934 FCC ID into their own products Vcc CYWM6934 Module 12 pin 2mm header Bypass capacitors CYWM6934 Functional Description The CYWM6934 WirelessUSB LS Radio Module offers a complete radio module solution for integration into existing or new 2 4 GHz products The CYWM6934 is tested for functional operation and is FCC ETSI EU Industry pre certified The module is supplied with an integrated PCB trace antenna The CYWM6934 is available in a small PCBA design and can be mounted horizontally to the device PCB via a 12 pin header The pin out of the header is shown in Figure
14. actical to place the statement specified under paragraph a of this section on it the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or alternatively shall be placed on the container in which the device is marketed However the FCC identifier or the unique identifier as appropriate must be displayed on the device The users manual or instruction manual for an intentional or unintentional radiator shall bear the following cautionary statement Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 0 0 0 4 United States Regulatory Approval FCC Modular Approval MA The requirements for FCC Modular Approval were released in June 2000 in the FCC s Public Notice FCC Public Notice DA 00 1407 Part 15 Unlicensed Modular Transmitter Approvals Criteria for Modular Approval In our OEM instructions it is recommend that the following rules required by FCC grants be adhered to a Cypress FCC ID label must appear on the outside of their product FCC Public Notice DA 00 1407 instructs if the FCC ID is not visible when the module is installed inside another device then the outside of the device into that the module is installed must also display a label referring to the enclosed module This exterior label can use wording such as the following
15. ated and will have atleast 20 cm separation from the human body Note CYWM6934 0 0 0 3 Portable Application Module can be relocated and will have less than 20 cm separation from human body Correct Installation m Modules cannot be modified in any way m Modules must be used only in the operating range specified in the datasheets m Modules cannot be co located within 20 cm of another intentional radiator in the system m Must guarantee that end user cannot easily change antenna Note Sidestepping these requirements is possible with additional testing and or recertification However modular approval would no longer apply Correct Labeling If end device containing a WirelessUSB LS Module will be sold or used in the USA the enclosure of the product must display a label with the following basic elements FE CYWM6934 Contains FCC ID R8KUGWM1USHN33A If end device containing a WirelessUSB LS Module will be sold or used in Europe the enclosure of the product must display a label with the following basic elements C 0122 If end device containing a WirelessUSB LS Module will be sold or used in Canada the enclosure of the product must display a label with the following basic elements CYWM6934 This product contains Cypress WirelessUSB module CYWM6934 Canadian Cert No IC 5125A UGWM1US As of March 2006 Japan does not recognize the Modular Approval certification Regulatory certification
16. e Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement Any reproduction modification translation compilation or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress Disclaimer CYPRESS MAKES NO WARRANTY OF ANY KIND EXPRESS OR IMPLIED WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Cypress reserves the right to make changes without further notice to the materials described herein Cypress does not assume any liability arising out of the application or use of any product or circuit described herein Cypress does not authorize its products for use as critical components in life support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user The inclusion of Cypress product in a life support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges Use may be limited by and subject to the applicable Cypress software license agreement Document No 38 16012 Rev C Revised October 23 2014 Page 9 of 9 All products and company names mentioned in this document may be the trademarks of their
17. e the following text and must be affixed to the exterior of the OEM s product As shown in the Correct Labeling section 4 1 3 European Union Requirements and Regulatory Approval The requirements for EU Regulatory Approval were released in April 2000 in the EU R amp TTE Directive This directive supports self directed testing and certification for harmonized bands within OEM facilities or by third party In the case of WirelessUSB standards have become harmonized although frequencies are not The R amp T TE directive no longer requires a Technical Construction File however frequency notification to EU countries is still applicable Article 6 of the R amp TTE directive states The manufacturer or the person responsible for placing the apparatus on the market provides information for the user on the intended use of the apparatus together with the declaration of conformity to the essential requirements Ensuring regulatory compliance of the end product is the sole responsibility of the OEM Document No 38 16012 Rev C CYWM6934 Cypress maintains responsibility for conformance of the CYWM6934 the interconnect and the antennae as the manufacturer The R amp TTE directive maintains that first level compliance be reviewed by a Notified Body prior to general product marketing This is not mandatory but reduces the risk of the product being challenged for non compliance Although not specifically stated
18. rate the equipment The OEM must not modify any aspect of the radio s mechanical and electrical configuration 3 The OEM mustinclude compliance information in their user information a Although no additional regulatory work may be required for the radio the host device is probably subject to other FCC authorizations as a digital device DoC authorization is required for PCs and peripherals verification is required for most other digital devices Product Labeling Requirements FCC product labeling requirements stipulate an FCC label including specific text be placed on the device containing the CYWM6934 module The product label must include the following text and must be affixed to the exterior of the OEM s product As shown in the Correct Labeling section 4 1 3 Industry Canadian Requirements and Regulatory Approval Industry Canada regulatory approval typically conforms to the FCC in terms of emission levels and other regulatory requirements It is the position of the Industry Canada agency that the OEM primarily responsibility for ensuring end product compliance Cypress Unigen as grantee and supplier of the module maintains responsibility for the Modular Approved design Criteria for Modular Approval In our OEM instructions it is recommend that the following rules required by Industry Canada be adhered to a Cypress Industry Canada ID label must appear on the outside of their product lf the Industry Canada ID is
Download Pdf Manuals
Related Search