User Manual
Contents
1. 40 to 65 C non air flow environment Operating i ae 5 to 95 Non condensing Humidity Storage Temp 40 C to 85 C IP 30 48 6mm W x 95mm D x 140mm H FCC Class A CE EN61000 4 2 3 4 5 6 8 CE EN61000 6 2 CE EN61000 6 4 Safety cUL UL 508 IEC60068 2 32 Free fall Stability testing IEC60068 2 27 Shock IEC60068 2 6 Vibration EMC Table 4 Technical Specification 172. NCAaIra 5 port 10 100TX with 4 High Power PoE Injector Industrial Ethernet Switch User Manual antaira www antaira com FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Content IU OGUGUOM cana ccetoneat
3. Terminal Block Top View Note gt Use Copper Conductors Only 60 75 C Tighten to 5 Ib in gt The wire gauge for the terminal block should be in the range between 12 24 AWG Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as the picture shows below Inserting the wires will detect the fault status including power failure or port link failure managed industrial switch only and from a Normally Close circuit Please refer to Figure 8 for the fault alarm contact and Figure 9 shows the application example for the fault alarm operation mm PWR2 p Fail PWR1 24V dc 1A Resistance Figure 8 Terminal Block Front View for Fault Alarm Contact Figure 9 Fault Alarm Application Example Note gt Use Copper Conductors Only 60 75 C Tighten to 5 Ib in gt The wire gauge for the terminal block should be in the range between 12 24 AWG Mounting Installation DIN Rail Mounting The DIN Rail bracket is screwed on the switch on the production line in the factory If the bracket is not screwed on the switch please refer to Figure 10 to screw it on the switch Follow the steps below to hang the industrial switch m DIN Rail Bracket Figure 10 Rear side of the Switch 1 Use the screws to screw the DIN Rail bracket on the rear side of the industrial switch 2 To remove the bracket reverse the step 1 3
4. After the DIN Rail bracket is screwed on the rear side of the switch insert the top of the bracket into the rail as Figure 11 Figure 11 4 Then lightly pull down the bracket into the rail as shown in Figure 12 Figure 12 5 Check if the bracket is tightened on the rail or not 6 To remove the switch from the rail reverse steps above Wall Mounting Please refer to Figure 13 and follow the steps below to mount the industrial switch with wall mount bracket and the detail dimension of the bracket as Figure 14 1 Remove the DIN Rail bracket from the switch loose the screws to remove it 2 Place the wall mount bracket on the top side and bottom side of the switch 3 4 Use the hook holes at the corners of the wall mount bracket to hang the industrial Use the screws to screw the wall mount bracket on the switch switch on the wall To remove the wall mount bracket reverse steps above Figure 13 Wall Mount Bracket Installation 2 25 0 lt t N x 12100 9 00 _ 30 00 _ _ 15 00 Figure 14 Wall Mount Bracket Dimensions 12 Hardware Installation In this paragraph we are going to explain how to install the 5 port 10 100TX with 4 port High Power PoE Industrial Switch and the installation points to be attended to it Installation Steps 1 Unpack the Industrial switch packing 2 Check if the DIN Rail bracket is screwed on the Industrial switch or not If the bracket
5. Link 5 10 100TX w 4 port High Power PoE Industrial Switch y eae hoko ka cin fey b e VOIP Phone IP Camera Wireless AP IEEE 802 3af at compliant Powered Devices Figure 15 Network Application Troubleshooting m Verify that you are using the right power cord supplier adapter DC 48V please don t use the power supplier adapter with a non compliant DC output voltage or it will burn the equipment Select the proper UTP STP cable to construct your network Please check that you are using the right cable Use unshielded twisted pair UTP or shield twisted pair STP cable for RJ 45 connections 100Q Category 3 4 or 5 cable for 10Mbps connections 100Q Category 5 cable for 100Mbps connections or 100Q Category 5e above cable for 1000Mbps Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet m Diagnosing LED Indicators To assist in identifying problems the Switch can be easily monitored through LED indicators on the front panel which describe common problems the user may encounter and where the user can find possible solutions m f the power indicator does not light on when the power cord is plugged in user may have a problem with the power cord Then check for loose power connections power losses or surges at power outlet If you still cannot resolve the problem contact the local dealer for assistance m If the Industrial switch LED indicators are normal and th
6. e PoE function with per port 25 watts 48VDC output for kinds of Powered Devices with the higher power consumption requirement to receive power as well as data over an RJ 45 cable Features m System Interface Performance RJ 45 ports support Auto MDI MDI X Function Embedded 4 port PoE Injection Store and Forward Switching Architecture Back plane Switching Fabric 1 0Gbps 2K MAC Address Table m Power Input gt DC 48V Redundant Power Input m Operating Temperature gt Wide Operating Temperature with E model 40 C 75 C Case Installation gt IP 30 Protection gt Installation in a Pollution Degree 2 environment gt DIN Rail and Wall Mount Design m Provides EFT protection 3 000 VDC for power line Supports 6 000 VDC Ethernet ESD protection VV VV Y Package Contents Please refer to the package contents list below to verify them against the checklist m 5 port 10 100TX with 4 Port High Power PoE Industrial Switch with DIN Rail Bracket User manual Removable Terminal Block Wall mount Kit 2 wall mount bracket with screws Compare the contents of the industrial switch with the standard checklist above If any item is damaged or missing please contact the local dealer for service Hardware Description In this paragraph the Industrial switch s hardware specs ports cabling information and wiring installation will be described Physical Dimension 5 port 10 100TX with 4 port High Power PoE Industrial Sw
7. e connected cables are correct but the packets still cannot transmit Please check your system s Ethernet devices configuration or status Technical Specification The 5 port 10 100TX with 4 port High Power PoE Industrial Switch technical specifications is shown as below IEEE 802 3 10Base T Ethernet IEEE 802 3u 100Base TX Fast Ethernet Standard IEEE802 3x Flow Control and Back Pressure IEEE802 3at Power over Ethernet Protocol CSMA CD 14 880 pps for 10Base T Ethernet port Transfer Rate 148 800 pps for 100Base TX Fast Ethernet port MAC Address 2K MAC address table 10 100TX 5 x RJ 45 Connector Power P Fail 1 x 6 poles Removable Terminal Block RJ 45 port 1 4 support IEEE 802 3at End point Alternative A mode Positive VCC RJ 45 pin 1 2 Negative VCC RJ 45 pin 3 6 Data 1 2 3 6 PoE Pin Assignment Per unit Power 1 Green Power 2 Green P Fail Red Per port Link Activity Green Full duplex Collision Amber PoE Feeding Power Green 10Base T 2 pair UTP STP Cat 3 4 5 5e 6 cable EIA TIA 568 100 ohm 100m 100Base TX 2 pair UTP STP Cat 5 5e 6 cable EIA TIA 568 100 ohm 100m Over Current f Fast Blown Fuse Protection Redundant power DC 48V with connective removable Power Supply terminal block Max Power 110 Watts 48V Consumption Full load with PoE function Network Cable Installation DIN Rail mounting Wall mounting 40 to 75 C Operating Temp
8. e inputs PoE indicator On The port is supplying power to the powered device Port 1 4 ana Off No powered device attached or power supplying fails Green On Connected to network _ Flashing Networking is active LAN Port1 5 Off Not connected to network RJ 45 Amber On Full duplex link Flashing Collision occurs La Off Half duplex link or link down Table 1 LED Indication Definition Ports m RJ 45 ports The Fast Ethernet ports RJ 45 will auto sense for 10Base T or 100Base TX connections Auto MDI MDI X means that the switch can connect to another switch or workstation without changing straight through or crossover cabling Please refer to Table 2 for RJ 45 pin assignment Pin Number Assignment 1 TX 2 Tx 3 Rx 6 Rx Table 2 RJ 45 Pin Assignment Note and signs represent the polarity of the wires that make up each wire pair All ports on this industrial switch supports automatic MDI MDI X operation users can use straight through cables See figures below for all network connections to PCs or Servers or to other switches hubs In straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable Table 3 shows the 10BASE T 100BASE TX MDI and MDI X port pin outs Pin MDI X Signal MDI Signal Receive Data plus RD Receive Data minus RD Transmit Data pl
9. eteatnn ec 1 FEAE S een a E A lad tea 1 Package Contents sicscsisscincsssssexsecastaiasseiialediisaeevnincss 2 Hardware Description snsssssnnnnununnnnnnnnnnnnnnnnnnnnnnnnna 3 Physical Dimension ccccccesseeeeeeeeeseeeeeeeeeeeees 3 Front Panel oisase ccsdcsscsnsnccsvecbevesnaleendes i sa 4 TOD WIGW aE na aie aicanes Mareen aueieas 4 LED IG ICALONS 223 seceescee a bo hocc oan sere 5 POPS Seated herent ane et eee eae 6 Gali nre S etre ess ce ewes lege 7 Wiring the Power Inputs ccceeeeeeeteeeeeeeeeees 8 Wiring the Fault Alarm Contact c eee 9 Mounting Installation ccccccssessseeeseeseessneeeeeeneees 10 DIN Rail MOUNting ccccceceeesssssseeeeeessenseeeeeees 10 Wall MOunting ccccccccccsseesseeeeeeseeesseeeeeeeaeeesees 12 Hardware Installation ccccccsssessseeeseessessneeeeeenenes 13 Installation Steps ciana e a 13 Network Application ccccccceeetesesseeeeeeeeeeeeeeeeees 14 TROUDIECSNOOUING oannaam inaa k 15 Technical Specification csssseecesessssseseesees 16 Introduction The 5 port 10 100TX with 4 Port High Power PoE Industrial Switch is a cost effective solution which meets the high reliability requirements demanded by industrial applications and also supports to operate in the wide temperature 40 C 75 C environment Besides the equipment meets IEEE 802 3at pre standard it supports 48V DC power input and provides th
10. is not screwed on the Industrial switch please refer to DIN Rail Mounting section for DIN Rail installation If the user wants to mount the Industrial switch on the wall then please refer to Wall Mounting section for wall mount plate installation 3 To hang the Industrial switch on the DIN Rail or wall please refer to the Mounting Installation section 4 Power on the Industrial switch Please refer to the Wiring the Power Inputs section for knowing the information about how to wire the power cord The power LED on the Industrial switch will light up Please refer to the LED Indicators section for indication of LED lights 5 Prepare the twisted pair straight through CAT 5 above cable for Ethernet connection 6 Insert one side of the RJ 45 cable into the Industrial switch Ethernet port and another side to the network device s Ethernet port e g Switch PC or Server The Ethernet port RJ 45 LED on the Industrial switch will light up when the cable is connected with the network device Please refer to the LED Indicators section for LED light indication 7 When all connections are set and LED lights all show in normal the installation is complete Network Application This segment provides the sample to help user have more actual idea of industrial switch application For a sample application of the industrial switch see the Figure 15 below gt Control Center s T Fiber Cable Core Upper Level Switch Up
11. itch dimensions W x D x H is 48 6mm x 95mm x 140mm the detail dimensions as Figure 1 gt POO o o oo o ao 0 6 oo 0 o oo 0o PPP O o o o 96 e ooo e o oppooo e eo 99 0 0 0 0 0 0 0 0 0 0 0 0 0 oono CEES oo otoo 05039 2525202020200000 O50 20202000202 eWDoovrveccoooso Figure 1 Mechanical Dimensions 3 Front Panel The Front Panel of the 5 port 10 100TX with 4 Port High Power PoE Industrial Switch is shown below Figure 2 Figure 2 Front Panel of the Switch Top View The top view of the 5 port 10 100TX with 4 port High Power PoE Industrial Switch has one terminal block connector of two DC power inputs and Relay circuit contact Please refer to Figure 3 for further information So 9 4 PWR 1AG 24V PWRI O o al he Sl o eH EO V2 V2 4 Vi Vis P Fail DC 48V Figure 3 Top View of the Switch 4 LED Indicators The diagnostic LEDs located on the front panel of the industrial switch provide real time information of system and operation status Table 1 provides the description of the LEDs status and their definitions for the switch LED Color Description 5i PSA On Power input 1 is active Off Power input 1 is inactive 3 eae On Power input 2 is active Off Power input 2 is inactive On Power input 1 or 2 has failed P Fail Red Power input 1 and 2 are both functional or no power m
12. us TD Transmit Data minus TD Transmit Data plus TD Receive Data plus RD Wy N Transmit Data minus TD Receive Data minus RD Table 3 MDI MDI X Port Pin outs 6 The following figures show the cable schematic for straight through type Figure 4 and crossover type Figure 5 Switch Router PC 3 TD 3 RD 6 TD 6 RD 1 RD 1 TD 2 RD 2 TD Figure 4 Straight Through Cable Schematic Switch Switch 3 TD 3 RD 6 TD 6 RD 1 RD 1 TD 2 RD 2 TD Figure 5 Crossover Cable Schematic Cabling Twisted pair segments can be connected with unshielded twisted pair UTP or shielded twisted pair STP cable The cable must comply with the IEEE 802 3u 100Base TX standard e g CAT 5 CAT 5e or CAT 6 The cable between the equipment and the link partner switch hub workstation etc must be less than 100 meters 328 ft long Wiring the Power Inputs Please follow the steps below to wire the power cord which from the other compliant external DC power supplier 1 Insert the positive and negative wires into the PWR1 V1 V1 and PWR2 V2 V2 contacts on the terminal block connector as shown in Figure 6 V2 V2 V1 V14 Figure 6 Terminal Block Front View for Power1 amp Power2 Contact 2 Tighten the wire clamp screws which as shown in the Figure 7 for preventing the wires from loosing Figure 7
Download Pdf Manuals
Related Search