SIMATIC HMI SCD1900, 19” Touch Operating - Internet
Contents
1. Panel cut out 292 0 Fig 4 Dimensions of the SCD1900 portrait Seite 12 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch Thermal In order that the LCD device maintains an optimum operating temperature while in use air must be allowed to circulate freely around the SCD1900 enclosure It is particularly important that the rear of the system is kept free Please bear in mind that increased temperatures can lead to defects and to a significant reduction in the lifetime of the device EMC This LCD device is a piece of equipment designed for building into an industrial system The operator of the entire plant is responsible for maintaining electromagnetic compatibility according to EMC laws Safety All voltage and signal connections must adhere to appropriate legal requirements Ergonomics The screen should be easily viewable from all sides and without reflections Harmful gas Supply air with harmful gas is not allowed because of limitation in harmful gas resistance 2 4 Cable Connections and Pin Assignments The LCD device has been tested and set up in the factory Before use the power supply and the signals should be connected to the sockets provided Connections to the device should adhere to EMC regulations The added DVI cable should be used for the signal connection to the PC alternative can be used the VGA cable For the use of the Touch screen connect the SCD1900 with PC via the USB cable2. Bedienhandbuch SIEMENS SIMATIC HMI SCD1900 19 Touch Operating Instructions SCD1900 6AV7862 2TA00 1AA0 Landscape 6AV7466 2TA17 0AA0 Portrait Copyright Siemens AG SIMATIC HMI SCD1900 Seite 1 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch No part of this document may be reproduced or transmitted without express permission Violations will result in prosecution All rights reserved 2011 All rights reserved SIMATIC HMI SCD1900 Seite 2 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch Contents 1 OVERVIEW 5 nennen 5 1 1 Layout of this Handbook sss sese D 1 2 Warnings and Safety Notes 2 7 1 3 Instructions for Handling Components Susceptible to Electrostatic discharge 8 2 General Installaton 2 28 2 9 2 1 Removing the Packaging and Checking Individual Parts nnn 9 2 2 Scope of Delivery nsi neden ied lala Rd EL ELL 9 2 3 Installing the LCD Device sree eneen 9 2 4 Cable Connections and Pin Assignments nnen nennen eneen 13 ZAM DYI Tai AC Cy steen erna EN NR ER 14 24 2 VGAHWMCM ACE arr rien nalen eher 15 243 TouchAnlerlace USB sec Renee biden tees 15 24 4 POWerSupplyar renesse 16 2 4 4 1 24Vpe Power SUPpIy eee eee 16 2 4 4 2 230 Vac power supply optional sss eee 16 2 5 Electrical Installation ass neh 16 2 6 TouchiFunctionaliyvz zn green E E al AE ee 17 2 6 1 Installation of touch driver software UPDD nn
3. Reference number EN 60950 1 2006 A11 2009 A1 2010 A12 2011 EN 55022 2006 A1 2007 EN 61000 6 2 2005 IEC 61131 2 2007 Namur NE21 2006 Wolfratshausen 18 02 2013 EIZO Technologies GmbH ppa Thomas Henkel Diese Erkl rung bescheinigt die bereinstimmung mit den genannten Richtlinien ist jedoch keine Beschaffenheits oder Haltbarkeitsgarantie nach 443 BGB Die Sicherheitshinweise der mitgelieferten Produktdokumentation sind zu beachten This declaration certifies the conformity to the specited directives but does not imply any warranty for propertes The safety documentation accompanying the product shall be considered in detail SAGKwordGK SCD 1900 DE2 doc SIMATIC HMI SCD1900 Seite 27 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 5 Remarks and contact addresses 5 1 Remarks Invalidity of guarantee All unauthorized electrical or mechanical alterations on or in the unit result in loss of the guarantee Information on the Instruction Manual For clarity reasons this Instruction Manual does not contain all detailed information on this product Your attention is additionally drawn to the fact that the contents of this Instruction Manual are not part of a previous or existing agreement commitment or statutory right and do not change the latter Warranty All commitments on the part of Siemens AG are contained in the respective sales contract which also contains the complete and solely applicable war
4. SIMATIC HMI SCD1900 Seite 13 29 DOC No SCD1900 MANUAL DOC 24 1 DVI Interface The DVI interface is a 29 pin DVI connector SIMATIC HMI SCD1900 TMDS Data 2 TMDS Data 2 TMDS Data Shield 2 GND fe EN mm nn TMDS CLK TMDS CLK Seite 14 29 Bedienhandbuch DOC No SCD1900 MANUAL DOC Bedienhandbuch 2 4 2 VGA Interface The VGA interface is a standard 15 pin male HD D type connector Video input RED TOO oe 2 Jo 6 END RED GND GREEN 8 JeND BLUE 9 Notused O 2 4 3 Touch Interface USB SIMATIC HMI SCD1900 Seite 15 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 2 4 4 Power supply As the Power supply will be used a 24 V pc power connector or optional the external 230 Vac power supply on the rear of the unit 2 4 4 1 24Vpc power supply Type Phoenix MSTB 03G en Som Tann Ee 2 4 4 2 230 Vac power supply optional The AC DC power supply unit 24 Vpc is fixed by a bracket on the rear of the unit The connector of the DC 24V supply line will be plugged into the DC interface of the SCD1900 The cables will be fixed depending from the version with cable clips or binder to avoid unintended disconnection of the plug from the device 2 5 Electrical Installation Before connecting the SCD1900 to the power supply it should be checked if the signal connector is plugged in properly and that the screws are tightened There
5. Scroll down or select menu idem in main menu submenu Invoke via key lt MEN gt P picture X brightness 123 B advanced B contrast 123 Z options 1 ER h position 123 gein 2 E v position 123 oons phase 123 EA frequency 1234 utilities db infos The OSD varies depending form the represented signal source OSD functionality by represented RGB VGA signal and DVI signal are described in the following captures SIMATIC HMI SCD1900 Seite 21 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 3 2 2 1 Structure of the On Screen Display Menu DVI Main menu Function Adjust function value range Description Picture 1 Brightness setting range adjust brightness 0 to 100 through key Contrast setting range adjust contrast 0 to 100 through key change contrast between dark and light colors scaling fill all fill aspect ratio scaling of the picture Picture 2 Sharpness 1 2 3 4 5 adjust sharpness of the picture by using no 1 to 5 1 sharp 5 soft Gamma Linear or CRT correction of gamma curve value of colors will be forwarded to the display Color temperature 5000 7300 9300 VAR color temperature adjust color three defined and one adjustable color temperatures are for selection Activate VAR for RGB shows up an adjustment beam 0 to 100 50 correspond to factor 1 Option 1 OSD select between nine defined OSD define position OSD pos
6. control keys Key Function e Start Quick OSD Menu e Increase the parameter value e Selection of the input signal e Automatically alignment of the pictures e Decrease the parameter value MEN e No function in the Quick OSD SET e Start Quick OSD Menu e Adjust the contrast brightness e Choose of Quick OSD function SIMATIC HMI SCD1900 Seite 19 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch Following adjustments can be done via the Quick OSD menu Invoke via key lt SET gt Function Adjustment value Description a Range 0 to 100 Contrast adjustment contrast Spel via key lt gt lt gt _ __ eines Range 0 to 100 Brightness adjustment 123 via key lt gt lt gt Invoke via key lt gt Function Adjustment value Description Source digital DVI Press lt SET gt to Selection of input source RGB choose Press lt gt to select Auto Adjust Press key lt gt to Perform an automatic image press lt gt start the adjustment adjustment Adjustment of frequency phase and image position SIMATIC HMI SCD1900 Seite 20 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 3 2 2 OSD Menu Function s of the control keys Key Function e Increase the parameter value e Goto the right e Decrease the parameter value e Go to the left MEN e Start OSD e Select the main menu submenu SET e
7. image Info Firmware Show the firmware version and timing data of the present input signal Resolution Timing SIMATIC HMI SCD1900 Seite 23 29 DOC No SCD1900 MANUAL DOC 3 2 2 2 OSD Menu Function VGA Bedienhandbuch Main menu Function Adjust function value range Description Picture 1 Brightness setting range adjust brightness 0 to 100 through key Contrast setting range adjust contrast 0 to 100 through key change contrast between dark and light colors H Position setting range move picture in horizontal direction 0 to 100 through key V Position setting range move picture in vertical direction 0 to 100 through key Phase setting range adjust phase of input signal 0 to 31 through key Frequency setting range adjust frequency of input signal 950 to 1050 dependent to picture through key scaling fill all fill aspect ratio scaling of the picture Picture See chapter Structure of the On Screen Menu DVI page 22 Option 1 See chapter Structure of the On Screen Menu DVI page 22 Option 2 See chapter Structure of the On Screen Menu DVI page 23 Option 3 See chapter Structure of the On Screen Menu DVI page 23 Utilities See chapter Structure of the On Screen Menu DVI page 23 Info See chapter Structure of the On Screen Menu DVI page 23 SIMATIC HMI SCD1900 Seite 24 29 DOC No SCD1900 MANUAL DOC Be
8. the Internet eee eee 29 SIMATIC HMI SCD1900 Seite 3 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch Figures Fig 1 Mounting of SCD1900 aen ata 10 Fig 2 Clamp for mounting 10 Fig 3 Dimensions of the SCD1900 landscape nnen 11 Fig 4 Dimensions of the SCD1900 portrait 12 Fig 5 Location of the operation and alignment Controls 18 SIMATIC HMI SCD1900 Seite 4 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 1 Overview The LCD device SCD1900 has been developed and constructed especially for industrial applications This device can be used in industrial systems with particular demands e g immune to electromagnetic radiation Its compact enclosure opens up a wide spectrum of possible application areas for the SCD1900 The monitor is available for two orientations portrait and landscape With the use of the trend setting LCD technology in this device relegated picture geometry distortion and color patches are no longer an issue Even at the low refresh rate of 50 Hz the screen remains flicker free The SCD1900 thus fulfils even the strictest ergonomic requirements Pictures of lower resolution are expanded to fill the screen The monitor is available in landscape version and portrait version The SCD1900 can display up to 16 7 Mio colors This allows showing true color images and videos The LCD device contains special hardware to convert a standard analogue VGA and digital DVI video signal
9. CD1900 MANUAL DOC Bedienhandbuch 4 8 EU Declaration of Conformity on EMC amp eizo EIZO Technologies GmbH EG Konformit tserkl rung EC Declaration of Conformity Hersteller a EIZO Technologies GmbH Anschrift Burgermeister Seidl Str 8 anche D 82515 Wolfratshausen Germany Produktbezeichnung Productdescription SCD1900 Das bezeichnete Produkt ist entwickelt konstruiert und gefertigt in Ubereinstimmung mit den Richtlinien The described product is developed constructed and produced in conformity with the following European Directives 2004 108 EG Richtlinie des Rates zur Angleichung der Rechtsvorschriften der Mitgliedstaaten ber die elektromagnetische Vertr glichkeit Council Directive on the approximation of the laws of the Member States relating fo electromagnetic compatibility 2006 95 EG Richtlinie des Europ ischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der Mitgliedstaaten betreffend elektrische Betriebsmittel zur Verwendung innerhalb bestimmter Spannungsgrenzen Directive of the European Parliament and of the Council on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits CE Kennzeichnung CE marking 2011 Die Konformitat mit den Richtlinien wird nachgewiesen durch die Einhaltung folgender Normen Conformity to the Directives is assured through the application of the following standards Referenznummer
10. Compatibility with conventional CRT devices is guaranteed The adjustment of the device will be done via the clearly designed OSD On Screen Display Tedious adjustments are a thing of the past with the Automatic Alignment function At the press of a button the monitor performs these alignments automatically The SCD1900 is equipped with an active 19 TFT display module with a maximum resolution of 1440 x 900 pixels The integrated power management system VESA DPMS allows a significant reduction in power consumption when the synchronization signal from the computer has been switched off compared with that under normal operation SIMATIC HMI SCD1900 Seite 5 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 1 1 Layout of this Handbook This handbook should be kept within reach while installing and operating the LCD device It has been laid out so that even inexperienced users can find the information they require Chapters are clearly arranged according to subject In detail the chapters are arranged as follows Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Important Introduction This chapter provides a brief description of the SCD1900 including its properties application areas and special features Installation This chapter is mainly concerned with preparing the LCD device for use its installation and cabling Operation All operations and adjustment possibilities for the SCD1900 are described
11. Hz u Hz SIMATIC HMI SCD1900 Seite 22 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch Main menu Function Adjust function value range Description Option 3 Noise suppression ON OFF Standard setting OFF At ON Activation of function for noise suppression in synchronization signals Inhibits new auto alignment during display of a video signal when short term noise is present on synchronous signals Lock RGB Signal 1 ON lt Key gt Standard setting OFF At ON The video timing currently shown will be stored and processed with higher tolerance in H and V frequency l e the settings of this timing will always be used even if variations in H and V frequency will occur by noise Prevents erroneous recognition of timing when recognizing a noisy video signal e g showing up as wrong centering or resolution of picture Unlock RGB Signal 1 OFF lt Key gt Standard setting OFF Video timing 1 released again Lock RGB Signal 2 ON lt Key gt Standard setting OFF At ON The video timing currently shown will be stored and processed with higher tolerance in H and V frequency l e the settings of this timing will always be used even if variations in H and V frequency will occur by noise Prevents erroneous recognition of timing when recognizing a noisy video signal e g showing up as wrong centering or resolution of picture Unlock RGB Signal 2 OFF lt Key gt Standard setting OFF Vi
12. are many possible reasons why an image might fail to appear on the display after it has been switched on e no signal connected e no synchronization signal connected e horizontal and vertical synchronization signals are connected the wrong way round SIMATIC HMI SCD1900 Seite 16 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 2 6 Touch Functionality The documentation and software for starting up of Touch are included on the CD which is part of the delivery The following Software tools are part of the CD e UPDD Touch driver and calibration e Touchlnput Virtual Keyboard e OnSreenKeyboard OSK Gina Possibility for enter into Windows login screen via Touch 2 6 1 Installation of touch driver software UPDD For installation of the touch driver software follow the instruction in user manual UPDD en pdf on CD 2 6 2 Calibration the touch screen The calibration is described in the file UPDD doc on the CD SIMATIC HMI SCD1900 Seite 17 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 3 Operation and Alignment This chapter contains a description of all the operating and alignment functions 3 1 Location of the Operation and Alignment Controls All the controls are accessible from the rear of the unit Following Fig 5 shows the position These controls are used for navigating for selecting and altering parameters in the OSD menu MEN SET VGA interface 24 Vic USB Power supply DVI D interface Touch interface Fi
13. deo timing 2 released again Utilities Language English German OSD language Factory reset lt gt press Reset of values like brightness contrast to default values Installation RGB lt gt press Enter a new timing which is not in the internal timing table This Mode function should used when the shown image resolution is not the resolution are expect When press lt gt the sub menu expect 9 timing parameter When lt gt H and V Frequency Show the H and V Frequency of the present input signal H V total H V start Show the used timing parameter of the present input signal Option Var RGB Mode inactive Mode1 Inactive used the internal timing table only Mode2 Mode3 Mode use the timing parameter and perform a complete auto adjustment usually used Mode2 use the timing parameter and perform an auto adjustment without an automatic image position adjustment Mode3 use the timing parameter and perform an auto adjustment without an automatic frequency adjustment H resolution 100 to 2000 through key Horizontal image resolution V resolution 100 to 2000 through key Vertical image resolution H total 100 to 2500 through key Whole pixel per line H Start 0 to 750 through key Number of Pixels from H sync start to image start V Start 0 to 500 through key Number of lines from V sync start to image start Install lt gt press Activate the feed timing parameter test pattern lt gt press Show a test
14. dienhandbuch 4 Technical Data 4 1 Display Module 48 1 om aD Display area WxH landscape 408 2 x 255 2 mm Resolution landscape 1440 x 900 pixels Viewing angle min L R 85 Landscape 80 Portrait O U 80 Landscape 85 Portrait 4 2 Power Supply Input voltage Limited power source max 8A 18 36 Voc dl Power consumption Standby approx 5 W 4 3 Operating Conditions Operating temperature 5 to 40 C Storage temperature 20 to 60 C Relative humidity in operation max 85 by 30 C 4 4 Protection Protection Class IP65 front SIMATIC HMI SCD1900 Seite 25 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 4 5 Enclosure Weight approx 5 5 kg 4 6 Mechanical requirements 4 6 1 Operation Vibration According to EN 60068 2 6 5 8 5 Hz with 3 5 mm deflection 8 5 150 Hz at ig According to EN 60068 2 29 50 m s 30 ms 4 6 2 Packed unit Vibration According to EN 60068 2 6 5 8 5 Hz with 3 5 mm deflection 8 5 500 Hz at ig According to EN 60068 2 29 250 m s 6 ms in storage packaging 4 7 Input Signal 4 7 1 Digital Signal Type Standard signal DVI 1 0 Pixel Frequency 25 140 MHz 4 7 2 Analog Signal Level Video 0 7 Vss RGB analogue at 75 Q Bandwidth 300 MHz 3dB Synchronization Sep Sync TTL Sync on green Composite Sync H Frequency 30 to 97 kHz V Frequency 50 to 72 Hz SIMATIC HMI SCD1900 Seite 26 29 DOC No S
15. e Removal of all packaging e Checking of components for damage e Comparison of components received with those on the delivery note e Connection to the computer system and power supply e Building into your system bearing in mind technical and ergonomic aspects 2 1 Removing the Packaging and Checking Individual Parts After unpacking all the delivered components they should be checked for completeness and for possible transport damage visual inspection If any deficiencies are found then please contact the service department given on the delivery note Have the delivery note number serial number and a description of the deficiency to hand The original packaging should be kept for future transportation 2 2 Scope of Delivery e Cable set 1 8 m VGA USB und DVI e 10 bracket e Documentation e Driver CD 2 3 Installing the LCD Device The SCD1900 will be placed in panel cut out and mounted with 10 clamps see Fig 1 and Fig 2 at the cut out frame in the rear 3 clamps each top bottom and 2 clamps each left right To fix the device the clamps will be hang in the provided holes at the bezel and the screws tighten max 50 Nem see Fig 1 and Fig 2 The panel cut out is prepared according to the drawing see Fig 5 The SCD1900 must be close fitting to the panel to keep the protective If the surface structure is coarsely to leaks must be tested Attention All 10 clumps must be used and both hooks must be hanged up The mo
16. en eennennnnnnenennn 17 2 6 2 Calibration the touch Screen ee 17 3 Operation and Alignment een 18 3 1 Location of the Operation and Alignment Controls eenen 18 3 2 Using and adjusting the device cesta cccbtensderctenecevetendcaceteebccveteedcaveterdene tevseneiteees 19 3 2 1 OLIEKOSD MONW stee eert etat ats ee ats No ebt at Nos a 19 322 OSD MGM cas covers edentate dd dd dd dd 21 3 2 2 1 Structure of the On Screen Display Menu DVI 22 3 2 2 2 O5D Menu Function Voss Re 24 4 Technical Data s lt s22sss stag SER REN PSEE EHEE ELDER EEE REES re auaina iiaa pasilo dekpu redka 25 4 1 Display Module en 25 4 2 Power SUP OLY sr ee Een ebs onte elen teke FRI desbe int tete eee eeaeee GE 25 4 3 Operating Gel ple jie g Cn 25 4 4 PROUCCHON rarr rr ERROR a e A e E E A E E AEA saad 25 4 5 Saatel 26 4 6 Mechanical requirements eee eee eee eee ee ends 20 Be eel f iio 0 Arseen aneka rrd ed eiken dread den 26 402 Packed niks antennata ashes 26 4 7 Input Signal te Deden 26 44 11 DietalSiGnal rc Er idee eels alates A BAIE enb enen eeb dees 26 4 7 2 gt Analog SIGN Zeine nend Berne series 26 4 8 EU Declaration of Conformity on EMC sese eee eee eee 27 5 Remarks and contact addresses cr nennen ne nnnennnenenn nennen nennen 28 5 1 Remarks art serre AE E AE E E E E EE EA 28 5 2 POMONA SUD POF a mts AA S A IEA A E 28 5 3 Trainings Cente snene en ee 29 5 4 TeGhiniGal SUPPONE en san E E E TE 29 5 5 Service amp Support on
17. g 5 Location of the operation and alignment controls The functions of the keys are described in chapter 3 2 1 and 3 2 2 SIMATIC HMI SCD1900 Seite 18 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 3 2 Using and adjusting the device Since there are no standards for video output signals from graphic cards the first time the unit is switched on in DVI use it will automatically adjust itself to the pixel resolution card currently being used Via the analog VGA interface an automatically identification of the resolution thru the PC is not possible the adjustment must be done manually via the operation system Start gt adjustment gt system control gt display Some standard graphic controllers with included driver do not support the resolution In that case a similar resolution should be selected The picture will be adjusted to the resolution of the monitor by its internal electronic Because of the interpolation the picture is slightly diffuse Basically the digital DVI interface is recommended OSD Menu Quick OSD Menu The On Screen Display OSD is a menu system which is shown on the display With the help of OSD and the described controls elements 4 keys in the rear all adjustments of the device are executable In addition to the OSD menu there are more possibilities to adjust important functions like brightness contrast and automatic adjustment directly via a Quick OSD menu 3 2 1 Quick OSD Menu Function s of the
18. here Technical Data This chapter contains technical details such as dimensions power supply environmental considerations and EMC data Remarks The chapter gives you additional information and contact information The manufacturer has gone to great lengths to match the quality of the documentation to the high standard of this product In achieving this we are reliant on the support of our customers SIMATIC HMI SCD1900 Seite 6 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 1 2 Warnings and Safety Notes Transport The LCD device should only be transported in its original packaging to ensure it will be protected against shocks and rough handling setting up When installing the device it should be noted whether any moisture condensation has entered the unit during transport or storage Additional important installation information can be found in the Technical Data chapter EMC This LCD device is a component designed for building into industrial systems The operator of the entire plant is responsible for maintaining electromagnetic compatibility according to EMC law Repairs Before the unit is opened the supply voltage must be switched off Only authorized persons may open the unit Additions or changes to the unit may damage the system or affect its EMC behavior Cleaning The unit must be isolated from the power supply before cleaning If heavily soiled the LCD device can be cleaned with a damp cloth and mi
19. itions OSD H Position setting range move OSD menu in horizontal position 0 to 100 through key OSD V Position setting range move OSD menu in vertical position 0 to 100 through key OSD timeout 5 60 seconds adjust time after the OSD menu is automatically fade out the adjustment ensures between 5 to 60 s in steps of 5 s OSD background Opaque Transparent Select background color of the OSD menu you have the choice between transparent and colored background Backlight setting range Adjust brightness of backlight 0 to 100 through key herewith you can match the brightness of the picture with the brightness of the room Option 2 DPMS ON OFF Display Power Management System DPMS on or off If DMPS activated the device is turn off backlight when a synch signal is left The screen is dark Source scan OFF ON Standard ON Note To scan new video source is not relevant because the device has one RGB input source only Blank color red green blue black Choose the background color of the screen when no input signal is present Info signal source ON OFF Input source icon on or off The icon is shown when input signal are changed The icon shows the following information s signal source e g RGB analog Mode number internal mode number of the timing list Image resolution of the input signal H and V frequency Analog RGB1 Modus d d x d u 03u k
20. ld detergent Care must be taken to ensure that no moisture enters the unit during cleaning Scouring powders and solvents must never be allowed to come in contact with the unit The inside of the unit is to be cleaned by qualified service technicians only SIMATIC HMI SCD1900 Seite 7 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 1 3 Instructions for Handling Components Susceptible to Electrostatic discharge Most of the assemblies within the SCD1900 contain components which can be destroyed by electrostatic voltages It is also possible for the assemblies to be damaged in such a way that total failure does not occur If you as an authorized service technician are handling such assemblies then the following precautions should be observed e When such assemblies are being handled a means of electrostatic discharge must be available This can be for example a grounded object which can be touched to discharge electrostatic voltages e This applies to all insulated used tools They must also be discharged at grounded object e When assemblies are removed or added to the system the unit must always be switched off and the power supply cable disconnected e Vulnerable assemblies should always be held by their edge Avoid touching tracks and contact pins SIMATIC HMI SCD1900 Seite 8 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 2 General Installation Preparation for installing the LCD device includes the following points
21. nitor is available for two orientations portrait and landscape SIMATIC HMI SCD1900 Seite 9 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch Vertical installation and deviations between 20 and 20 is permitted 20 20 I x Clamp Device A Panel Fig 1 Mounting of SCD1900 Hook Clamp Screws for fixing Fig 2 Clamp for mounting SIMATIC HMI SCD1900 Seite 10 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch A 1 2 cman ol OT al IHH Dimensions do not include screw head Convection must be guaranteed Panel cut out 292 Panel cut out 450 Fig 3 Dimensions of the SCD1900 landscape SIMATIC HMI SCD1900 Seite 11 29 DOC No SCD1900 MANUAL DOC SIMATIC HMI SCD1900 Bedienhandbuch 18 5 123 6 Power 24VDC USB Touch a gt 226 5 VGA DVI 310 0 7 BIEMERS FAIR IM io lt er o Ss o x Su rrounding gasket Zinc coated metal housing a DODO 0G BO OURDONODO NEGO NOON o Aluminium powder coated front panel RAL9023 metallic fine structure Dimensions do not include screw head Convection must be guaranteed DROODONSODSEOLDLODOLOUDENDES Panel cut out 450 0
22. ranty conditions These warranty conditions in the contract are neither extended nor limited by the contents of this Instruction Manual Repairs Please contact your distributor from whom you originally purchased the product Environmental protection When disposing of the device the requirements and laws in the respective country must be observed 5 2 Additional support If you have any further questions about the use of products described in this manual and do not find the right answer here contact your local Siemens representative A guide to the technical documentation for various products and system is available on the Internet Internet www siemens com asis The online catalog and online ordering systems are also available on the Internet Internet www siemens com asis SIMATIC HMI SCD1900 Seite 28 29 DOC No SCD1900 MANUAL DOC Bedienhandbuch 5 3 Trainings Center To help you get started with automation technology and systems we offer you variety of courses Contact your regional Training Center or the central Training Center in D 90327 Nuremberg Germany Phone 49 911 895 3200 Internet www siemens com asis 5 4 Technical Support You can access technical support for al A amp D projects via the following Phone 49 0 911 895 7222 Fax 49 0 911 895 7223 Mail support automation siemens com Internet www siemens com asis 5 5 Service amp Support on the Internet In addition to our documentation
23. we offer y comprehensive online knowledge base on the Internet at e Following information will be found for example e Our newsletter containing up to date information on your products e The documents you need via our Search function in Service amp Support e A forum for global information exchange by users and specialists e You local Automation amp Drives representative e Information about on site service repairs and spare parts Much can be found under Services Internet www siemens com asis SIMATIC HMI SCD1900 Seite 29 29 DOC No SCD1900 MANUAL DOC
Download Pdf Manuals
Related Search