2.45GHz Long Range Reader
Contents
1. Bargate Output Gray RS232 TX OTR is One Time Reading Bargate is an open collector output TR Output Purple Max 100mA current drain about 1s low active pulse 8 Output Format 8 1 26bit Wiegand Output Timing Data bit 100us low active pulse Interval between bits 1ms 8 2 RS232 Output Format Data 0 B 100us lms Baud Rate 9600bps Parity None Data bit 8 Stop bit 1 LRC Exclusive OR XOR from Start 0x02h to End 0x03h Card ID PARADE 8 ASCII char 8 3 BARGATE Output Timing Low active pulse 1s duration End 0x03h LRC XOR Total 11 bytes BARGATE IDTECK IDTECK RF245 9 Wire Connection to Access Controller Access Controller Main Power 12V Bee roi Power Ground GND ss Wiegand Data 0 Output ESD Wiegand Data1 Output ani Buzzer Control Input SE OTR Control Input nelow Gray Bargate Output RS232 TX Purple __ LOI BIS 10 Operation 10 1 10 2 10 3 10 4 10 5 Apply the power to the reader The RF245 reader will setup receiving channel and Site Code automatically Then the Reader will get into standby mode after a successful initialization and diagnostics When a tag IDA245 5 or IDA245 10 is approaching to the reader then the reader will make a beep sound and turn red LED on simultaneously The reader will send the 26bit Wiegand output RS232 output and BARGATE output to the controller on t2. liquid or aerosol cleaners Use a damp cloth for cleaning If necessary use mild soap Do not use this product near water Only operate this product using the type of power source indicated If you are not sure of the type of power supplied to your installation site consult your dealer of local power company Never insert objects of any kind into the product or through the cabinet slots as they may touch voltage points and or short circuit parts possibly resulting in fire or electric shock Never spill liquid of any kind on the product Never disassemble this product by yourself take the unit to a qualified service center whenever service or repair is required Opening or removing the covers may expose you to dangerous voltages or other risks Also incorrect reassembly can cause electric shock when the unit is subsequently used Unplug this product from the Direct Current DC power source and refer to qualified service personnel under these conditions a When the power supply cord or plug is damaged or frayed b If liquid has been spilled on the product c If the product does not operate normally after following the operating instructions in this manual Adjust only those controls that are covered by the operating instructions in this manual Improper adjustment of other controls that are not covered by this manual may damage the unit and will often require extensive work by a qualified technician to restore normal opera
3. User s Manual IDTECK RF245 2 45GHz Long Range Reader IDTECK RF245 Table of Contents 1 Important Safety Instructions 3 2 OA ee ee 3 3 BEGIUIES o oslo ee ann one AA sera nenne 4 4 Specification nn nnennenn 4 5 Identifying Supplied Parts 2 00200220020000o 4 6 Installation 5 7 Color Coded Wiring Table T 8 Output Format nennen nennen 7 9 Wire Connection to Access Controller 8 10 Operation aaa aaa nennen nen nana nii ia 8 11 FCC Registration Information 9 12 Warranty and Service 10 13 Frequently Asked Questions 11 IDTECK IDTECK RF245 1 Important Safety Instructions When using RF245 basic safety precautions should always be followed to reduce the risk of fire electrical shock and injury to persons In addition the following safety guides should also be followed 1 2 3 Fully read and understand all instructions and follow them completely Follow all warnings and instructions marked on the product Do not use
4. W x H x D 5 Identifying Supplied Parts Please unpack and check the contents of the box IDTECK RF245 2 45 RF245 User s Manual Mounting Bolts 4 IDTECK IDTECK RF245 6 Installation Installation with Mounting Bracket 1 Tighten 8 x mounting bolts to the reader 2 Insert Mounting Bracket to the pole and tighten Ne the Y bolts 3 Setting the reading angle and tighten bolts nuts Mounting Bracket Installation with Mounting Bracket and Reader Hood D Insert Reader Hood in between the reader and the Mounting Bracket and tighten 5 x mounting bolts to the reader Reader inside 2 Insert Mounting Bracket to the pole and tighten the v bolts Reader 3 Setting the reading angle and tighten bolts nuts Hood Mounting Bracket 4 Optional Purchase Items Mounting Bracket Reader Hood IDTECK IDTECX RF245 Reading Angle of RF245 The reading angle of RF245 is approximately 90 degree at the front side of the reader However the reader has about 10 of the maximum reading distance at the rear side of the reader Reader 10 RD Applications Parking Control Island Multiple Gates Parking Control IDTECK 7 Color Coded Wiring Table SIGNAL Main Power 12V IDTECK RF245 Red Power Ground GND Black Wiegand Data 0 Output Green Wiegand Data 1 Output White Buzzer Control Input Blue OTR Control Input Yellow
5. coated by conductive materials for electrostatic discharge and the microwave RF from the tag is reflected on this conductive layer therefore the read range of the tag is reduced Q Why the tag does not read through the human body A RF245 Reader and IDA245 tag is using 2 45GHz ISM band very high directivity and only communicates at the line of sight distance The microwave can not pass through the human body Q Is the Reader weatherproof Can we install the Reader outdoor A The RF245 Reader is designed for outdoor use and all electronics are epoxy potted The Reader is weatherproof 10
6. he same time BARGATE Output When the reader detects the tag the reader also generates 1s BARGATE control output through the Grey wire The BARGATE output is a Transistor open collector output maximum current drain 100mA One Time Reading OTR Control Input When you setup the reader to One Time Reading Mode Tie OTR Control Input Yellow wire to GND the reader only generates ID outputs once if the tag ID detected for the first time and that ID stores into the memory to prevent sending same ID twice There is 5 seconds timer running on the OTR mode Therefore the outputs for the same tag ID generates only after the tag is away from the read range of the reader for 5 seconds BEEP Control Input When the BEEP Control Input Blue wire ties to GND the beeper of the Reader will be turned off Therefore the Reader will not make beep sound when the tag is detected 8 IDTECK IDTECK RF245 11 FCC Registration Information FCC REQUIREMENTS PART 15 Caution Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user s authority to operate the equipment NOTE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interface and 2 This device must accept any interference received including interference that may cause undesired operation This equ
7. ipment has been tested and found to comply with the limits for a Class A Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to this equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur ina particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the radio or television off and on the user is encouraged to try to correct interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on another circuit 4 Consult the dealer or an experienced radio TV technician for help IDTECK IDTECK RF245 13 Frequently Asked Questions Q Why the RF245 Reader can not read some tags A The RF245 Reader has a Site Code programmed when it powered up and the Reader only reads the tag has same Site Code To change the Site Code of the Reader power off for 5 seconds and power on again then try to read a tag The Reader will re program the Site Code sending from the tag Q The tag attached on the windshield of the car Why the tag in some cars have short read range A The windshield of some cars is
8. tion d If the product exhibits a distinct change in performance 2 General The RF245 is a 2 45GHz Long Range Reader for outdoor use and the read range of RF245 is maximum 16 feet 5 meter with IDA245 5 active tag and maximum 32feet 10 meter with IDA245 10 active tag The RF245 can be used for various applications such as Hands Free Access Control Parking Control Personal Tracking and Factory Automation The RF245 supports various output formats 26bit Wiegand output RS232 serial output and BARGATE output There are optional Mounting Bracket and Reader Hood for easy installation The RF245 has automatic setup for Channel setting Site Code setting when it powered up Red color LED and built in Beeper assures its accurate and reliable system operation IDTECK IDTECK RF245 3 Features 0 Long Range Reader 3 5m with IDA245 5 8 10m with IDA245 10 2 400GHz 2 524GHz Frequency 125 channel Encrypted Tag ID and Secure Protocols between Reader and Tags Multiple Tags Reading 30 Tags Sec 90 One Directional Antenna 26bit Wiegand and RS232 Output Format Direct Bargate Output Open Collector 100mA 1s 4 Specification Model RAB Receiving channel 125 channels Automatic Setting RS232 Format ___9600bps Parity None 8 Data bits 1 Stop bit 35 to 65 C 31 F to 149 F 10 to 90 relative humidity non condensing Ivory Polycarbonate Aluminum Anodized 1 36Kg 200mm x 200mm x 45mm
Download Pdf Manuals
Related Search