Home

Manual M EN 2014-1 - Multi

image

Contents

1. 1 INTRODUCTION WARRANTY DEFINITIONS SAFETY SYMBOLS You have made the right decision by purchasing the Multi Mover M You are now in the possession of an excellent tool that has been constructed and produced with the greatest care You will profit the most from this investment if you carefully observe the safety user and maintenance instructions provided in this user manual The user manual should be made available to the user of the Multi Mover M and must be present at the Multi Mover M when it is being used The user manual must have been read by anyone working with at the Multi Mover M and the instructions must be observed Warranty Multi Mover Europe BV will not assume responsibility for the goods it produced and the services it supplied Warranty can only be claimed if the client has made an immediate complaint and Multi Mover Europe BV has been given the opportunity to investigate the complaints and correct possible faults Multi Mover Europe BV provides a warranty on its products in relation to materials and con struction defects In case of defects as described above Multi Mover Europe BV shall undertake to provide the parts manufactured by them for free within the period of one year after delivery To occasions different warranty conditions apply Multi Mover Europe BV will not be liable for damage and indirect damage as a result of natural disasters operational errors lack of skilful maintenance and any other use than
2. Y qE 6 4 Cleaning When used inside and outside the bottom will become dirty with particles from the surroundings It is necessary to remove this dirt regularly as contamination could hinder the operation of the drive Do not use a high pressure cleaner or a hard water jet for cleaning as the electric and electronic system is not water tight and could be damaged 6 5 Taking out of operation If the Multi Mover M is not used for a certain period you will have to connect the battery charger place the Multi Mover M on blocks so that the tyres do not touch the ground Have maintenance and repairs performed by persons authorized by Multi Mover Europe BV In case of doubt always consult your supplier For the above mentioned maintenance instructions we assumed normal use In case of intensive use or use under extreme conditions maintenance will have to be performed with shorter intervals 6 6 Annual maintenance See 6 2 Check whether all bolts are still tight and check the rotation hinge points and guides for wear and play replace or overhaul if necessary Check the carbon brushes for wear and have them replaced if necessary only by qualified trained specialists 7 ENVIRONMENT 7 1 General Residues of lubrication oil oil stained cloths batteries and possible cleaning agents must be disposed of separately as chemical waste 7 2 Consequences for the environment Life span The expected life span of t
3. described below The liability of Multi Mover Europe BV will also terminate as soon as you or a third party performs work such as adaptations or extensions to the machine without our written permission The warranty conditions only apply if a defect after investigation by the manufacturer is recognized as such At Multi Mover Europe BV we continuously try to improve our products and service That is why we reserve the right to change the specifications stated in this user manual at any required moment and without prior notice Definitions In this user manual we use the following definitions Operator The person who drives controls and supervises the operation of the Multi Mover M and is able to start and stop it etc lt is the company s responsibility to make sure that the operator is suffi ciently trained Dangerous areas The area surrounding the Multi Mover M where people may get injured Maintenance mechanic The person who is completely familiar with the Multi Mover M is able to adjust the safety devices and to maintain the Multi Mover M The maintenance mechanic is familiar with the functionalities safety standards and was trained to maintain the Multi Mover M It is the com pany s responsibility to make sure that maintenance staff has been suffi ciently educated and trained Safety symbols On various places on the Multi Mover M you will find standardized safety symbol stickers as displayed to the right The upper par
4. driving on a limited slope or on slippery grounds Placement in on a lift Never manoeuvre the Multi Mover M in on a lift without permission drive it slowly place the vehicle correctly in the centre of this space switch off the vehicle with the ignition key Make sure there are no people on the lift when the vehicle is driven onto it Only transport safe and stable loads ee MULTI MOVER M Make sure the weight of the load to be moved lies within the capacity of the Multi Mover M The maximum traction force is stated on the type plate Caution Prevent serious damage to the drive the Multi Mover M may only be towed with the handbrake button 7 in the free position pulled out 5 3 Operation see photo fig 1 Steering handle Tillernead Fig2 7 Wheel with tyre Steering bar Swivel wheel Top coupling point Handbrake button Type plate Control box OoakWN Steering handles 1 The steering handle 1 with bar is a fixed part of the Multi Mover M moving to the left means driving to the left and vice versa Prior to putting the Multi Mover M into operation you must acquaint yourself with its possibilities Read the instructions in advance and check the function of the control units with the ignition key in the OFF position rat che Tiller head fig 2 Steering handle black Emergency stop red On Off switch left yellow Drive switch forwards and backwards middle yellow 2x Battery i
5. full Never interrupt the charging process make sure it is fully completed While charging the battery never perform repair cleaning or other work to the Multi Mover M MULTI MOVER M 12 Prior to disassembling the batteries switch off all power consumers because of the generation of Sparks When disassembling the batteries first disconnect the mass cable When assembling connect the mass cable as last Caution Always plus red to plus and minus black to minus Battery fluid is a corrosive acid avoid contact with clothing skin and eyes Immediately wash off possible splashes on clothes or skin with water and soap then rinse off with plenty of water Possible splashes of acid in the eyes rinse with clean water for at least 5 minutes and immediately consult a doctor When the battery is replaced the old battery should be returned to your dealer or handed in at a legally recognized collection point for batteries 5 5 Coupling trailer s The Multi Mover M is made with a standard tow eye with tow pin or a ball coupling point in the middle of the Multi Mover M to which the pole of a trailer can be coupled Maximum slope angle with without load 4 12 Slowly reverse the Multi Mover M to the pole of the trailer and place the tow eye or coupling of the pole between the tow eyes or coupling point of the Multi Mover M and insert the tow pin Then secure the tow pin with a spring clip Only use the Multi Mover M if
6. you have thoroughly studied the previous pages and you have no more questions Standard snowtyres and front tow bar 6 MAINTENANCE When performing maintenance you should always observe the safety regulations chapter 3 During maintenance always switch off the Multi Mover M and remove the ignition key from the ignition lock In case of doubt consult the user manual 6 1 Inspection The operator should perform the following inspections regularly without trailer it must be possible to rotate the steering handle swivel wheel smoothly to the left and right without jolts keep an eye on the wear of driven air tyres if the wheels slip in case of sudden brakes they will have to be replaced when accelerating quietly it must be possible to reach the maximum speed If one of the above tests is not satisfactory you must immediately report this to person who is directly responsible for the maintenance of the Multi Mover M 6 2 Lubrication and maintenance diagram d daily w weekly m monthly a annually MULTI MOVER M 13 m maintenance r replacement only by qualified trained specialists m r d w m a inspection cleaning bottom side Multi Mover M inspection battery charge depending on intensity of use inspection wear drive wheels E cleaning carbon brushes electric motor minimum replacing carbon brushes if less than 1 cm long lubricating nipples on bearings drive and swivel wheels v OORA OUON
7. USER MANUAL and PARTS LIST MULTI MOVER M TYPE 24Volt DC 500 Watt Transport Only use stable loading surfaces with sufficient loading capacity see section 2 2 Secure the MULTI MOVER M against tilting or sliding It is prohibited to get under the MULTI MOVER M while lifting remain within the tilting range of the MULTI MOVER M during unloading CC I _ CC OO a MULTI MOVER M Contents Chapter 1 INTRODUCTION WARRANTY DEFINITIONS SAFETY SYMBOLS 3 Chapter 2 TECHNICAL DESCRIPTION 4 2 1 Designation identification and description 4 2 2 Technical information and dimensions 4 2 3 Packaging loading unloading towing recycling 4 Chapter 3 SAFETY REGULATIONS 5 Chapter 4 PREPARATION 7 4 1 Application 7 4 2 Operator 8 4 3 Responsibility operator 8 4 4 Inspection prior to putting into operation 8 Chapter 5 USE 9 5 1 General 9 5 2 Regulations for use 9 5 3 Operation 10 5 4 Batteries 11 5 5 Coupling trailer s 13 Chapter 6 MAINTENANCE 13 6 1 Inspection 13 6 2 Lubrication and maintenance diagram 13 6 4 Cleaning 14 6 5 Taking out of operation 14 6 6 Annual maintenance 14 Chapter 7 ENVIRONMENT 14 Chapter 8 FAILURES 15 Chapter 9 PARTS 15 Chapter 10 DECLARATION OF CONFORMITY 16 Appendix Electrical circuit diagram Appendix II User manual battery charger Multi Mover Europe B V www multi mover eu T 31 24 744 00 70 F 31 24 890 17 90 T 49 2841 999 8083 Info multi mover eu OO OO oOo ee E MULTI MOVER M
8. been loaded evenly and safely 3 11 Caution Wear clothing that allows you to move freely and does not hinder your view on the Multi Mover M plus trailer s Observe your company s safety regulations 3 12 Caution Hazard of injury In case of an unusual noise Stop the Multi Mover M immediately Check the electric system and the drive for damage Check the wheels and tyres for tension damage and wear 3 13 Caution Avoid injury Regularly check whether there are any loose bolts and nuts Also see chapter 6 Maintenance 3 14 Caution Avoid injury by checking the Multi Mover M for damage or bends on a daily basis Pay particular attention to the tow eye with tow pen or coupling point and locking 3 15 Caution Hazard of injury Make sure the Multi Mover M is properly and safely supported when performing cleaning or mainte nance work under the Multi Mover M 3 16 Caution Hazard while charging the battery Make sure there is assistance within the range of your voice and also make sure there is sufficient soap and water nearby if you need to perform work near the battery Avoid short circuit sparks make sure you do not make an electrical connection between the battery poles Make sure no metal objects can fall on the battery as this could cause a short circuit or a spark and an explosion Remove personal objects such as rings bracelets necklaces and watches if you are performing work near the battery A short c
9. er M 3 23 As the operator you will determine the limits for safe driving working with the Multi Mover M Do not take any risks Be particularly careful in case of obstacles or uneven terrain 4 PREPARATION 4 1 Application The Multi Mover M was developed for moving trailers caravans trailers with or without goods order picking etc driving over flat dry metalled or unmetalled terrain e g warehouse greenhouse lawns etc The Multi Mover M is not suitable for transporting trailers with people The Multi Mover M is not suitable for moving goods containing toxic substances goods containing explosive substances goods containing hazardous substances combustible substances other liquids and hazardous substances than stated above The Multi Mover M does not have permission to be driven on public roads Only use the Multi Mover M for the purpose for which it was designed For other applications the CE mark does not apply The electric components and wiring have been made drip proof Therefore the Multi Mover M may not be used in the rain and must be covered in case of sprinkling or spraying plants The Multi Mover M must also be stored on a dry location 5 MULTI MOVER M Only the following original Multi Mover Europe BV parts and accessories may be used for the Multi Mover M Multi Mover Europe BV is excluded from any liability for damages or consequential damages that are caused by o
10. erature of the battery may not get too high as the acid will become more aggressive Here we are thinking of greenhouses and other heated spaces Frequent use If every 7 days the batteries are used on more than 3 days they will also wear more quickly When selecting batteries it is important to take into account the Multi Mover M s frequency of use If the batteries are used very frequently and intensively it will be necessary to select the 100AH 20h battery instead of the standard 55AH 20h battery Sulphation A battery will slowly discharge as a result of automatic discharge If a battery remains in a discharged condition it will start to sulphate and become damaged beyond repair We therefore recommend recharging the stored Multi Mover M every 2 months lt is also possible that there are still standby consumers in a switched off Multi Mover M key ignition etc which will mean that the batteries will discharge more quickly In that case regular recharging of the batteries is recommended Immediate recharging of an empty battery significantly promotes a longer life soan Further discharg ing than 20 has a negative effect on the life span The gases that are released while charging the battery are highly explosive detonating gas Therefore avoid fire and sparks near the charging location Charging may only take place in a well ventilated room Regularly check whether the battery charger stops automatically when the battery is
11. he Multi Mover M depend on maintenance operating hours and ambient conditions dust contamination humidity etc Good maintenance will be beneficial to the life span Disposal Preferably you should have the disposal and processing performed by a recognized dismantlement or demolition contractor who has the necessary permits Appoint a competent responsible person to supervise its execution Sort disassembled materials according to material characteristics and contamination Separate all materials that full under the category of chemical waste such as oil lubricants switching material batteries and certain electric components Dispose them as chemical waste Offer residual materials to recognized waste processing companies who have the required permits MULTI MOVER M 14 8 FAILURES When removing a failure ALWAYS switch off the Multi Mover M and remove the ignition key If a defect is established at the Multi Mover M do not use it until the repair has been com pleted Failure Solution A The Multi Mover M does not drive 1 Emergency stop has been pressed 1 Pull out 2 Battery empty 2 Charge battery 3 Battery clamps make poor contact 3 Clean attach again 4 Direction switch defective 4 Replace switch 5 Other causes 5 Consult your dealer 6 Electric brake uncoupled 6 Press brake handle B The Multi Mover M functions occasionally 1 Loose wiring 1 Check wiring 2 Dirty or worn carbon brushes 2 Clean or replace if less
12. he user manual You will prevent dangerous situations that might arise if the Multi Mover M starts to move unexpectedly Also consider the possibility that the vehicle is switched on by a third party a coincidence or misunderstanding that could occur if the ignition key is still in the ignition 3 3 Caution Hazard of serious injury due to getting jammed or a collision Make sure that nobody can get jammed also not at the trailer s that are being towed Particularly when riding along on the Multi Mover M or the trailer s to be towed there will be a risk of getting jammed or having a collision 3 4 Caution Hazard of serious injury on slopes due to tipping over The Multi Mover M was constructed for driving on flat dry metalled and sufficiently supportive terrain The maximum slope angle that can be driven on strongly depends on the weight to be towed the driving style of the operator driving circumstances and the strength of the terrain Caution Hazard of serious injury due to unwanted movements on slopes as result of insufficient traction force and brake force of the Multi Mover M Never drive onto a slope at an angle or crosswise Only ever drive on and off a slope at a right angle The Multi Mover M with trailer s may also tip over if the bends are taken at a speed that is too high 3 5 As the trailers may limit the operator s view and because the Multi Mover M and trailer s may swerve out there w
13. herefore not within the scope of the warranty arrangement Therefore we would like to draw your attention to the following Excessive load of the battery lf the batteries are loaded excessively this will strongly reduce the life span This means that you will have to adapt the load Discharging too deeply We recommend not to discharge the batteries completely If this happens often it will also result in premature wear Keep a close eye on the battery indicator connect the battery charger in time Adapted charger The batteries should be charged with a correct charger and during a specific period If the charging current is too low or if the duration of the charging process is too short the batteries will not be fully charged and the capacity of the batteries will be too low for your application resulting in premature wear If the charging current is too high or if the duration of the charging process Is too long the battery can be overcharged As a result the plates of your battery will overheat and may become damaged Intermediate charging If for example the batteries are empty for only 60 and are reconnected to the charger the batteries will not get the time to relax The temperature of the batteries will increase resulting in premature wear Also the voltage of the battery will become higher than the actual energy condition which means that the discharge limiter will no longer work correctly Ambient temperature The temp
14. ill be a risk of collision therefore Caution Hazard of serious injury due to collisions Make sure that bystanders remain at least 10 metres outside of the driving area of the Multi Mover M and trailer s 3 6 Caution Hazard of Serious injury due to getting jammed or as a result of falling under the Multi Mover M or trailer s Passengers may never drive along on the Multi Mover M or the trailers 3 7 Caution Hazard of serious injury Adapt your speed to the circumstances while driving Always make sure you have the Multi Mover M under control Reduce speed on uneven floors terrain and in sharp bends Be particularly careful when manoeuvring and reversing ae MULTI MOVER M 3 8 Caution Hazard of injury due to getting jammed when connecting and disconnecting the trailer s Keep your hands and fingers away from the coupling or pole eye 3 9 Caution Hazard of serious injury Before you start driving make sure the walking driving area is free and flat Avoid getting jammed between the Multi Mover M and obstacles Prevent tripping and getting jammed under the Multi Mover M and or trailer Make sure the driving area and your shoes are free of dirt in order to prevent accidents due to slipping 3 10 Caution Hazard of serious injury due to overloading the Multi Mover M The load behind the Multi Mover M may not be more than indicated at section 2 2 technical data Make sure the trailer s has have
15. ircuit for example could melt a ring resulting in serious burns 3 17 Caution Hazard of injury due to overheating of the electrical connection of the battery charger Pay particular attention to cable diameter earth and fuses n MULTI MOVER M 3 18 Caution Serious injury can be received or caused if the Multi Mover M is operated by persons younger than 16 years of age persons who do not have any training and driving experience with the Multi Mover M persons of whom it can be expected that they are not sufficiently aware of the dangers of the Multi Mover M temporary personnel for instance The MULTI MOVER M may only be operated after the operator has thoroughly studied the user manual and after the owner of the Multi Mover M has provided a full training instruction concerning the operation and the safety regulations 3 19 Caution Hazard of serious injury Serious injury may be received or caused if the safety instructions are not provided to other operators 3 20 Caution You are NOT allowed to use the public road with the Multi Mover M 3 21 Caution Hazard of injury if the safety symbols are not clearly visible any more Immediately replace damaged stickers 3 22 Caution Hazard of injury maintenance and repair work may only be performed by a maintenance mechanic who is recognized by Multi Mover Europe BV only original Multi Mover Europe BV or CE certified parts may be used in the Multi Mov
16. ndicator Potentio meter right yellow Ook WND OE LL LL CE OO E MULTI MOVER M Safety switch 2 2 When pressing the safety switch risk of getting jammed the Multi Mover M will stop immediately In order to start again the drive switch must first be placed in the neutral position Drive switches 2 4 left and right from the centre By rotating the drive switch 4 to the front with your thumb the driving direction will first be switched on and then when rotated further the Multi Mover M will start to drive The central position is the neutral position By rotating it downwards the Multi Mover M will reverse Handbrake button black 3 The wheels 1 7 are coupled to disconnected from the motor by means of the handbrake button If the button is pulled out it is in the free position the Multi Mover M can now be freely manoeuvred by hand If the button is pressed down the Multi Mover M can only be driven electrically The 24Volt charger can be plugged on to the red plug Caution Only switch to forward or reverse if the Multi Mover M is standing still 5 4 Batteries Battery charger connection The connection plug for the battery charger is located on the right side in a recess of the encasing On the dashboard of the Multi Mover M the battery indicator 8 is placed Red charge immediately Yellow charge soon Green battery is full For a longer life span it is better not to allow the battery to get comple
17. nt with fire hazard or explosion hazard While driving the generation of sparks may prevent switching on off The traction batteries are filled with hazardous electrolyte that could cause serious burns However the batteries are fully sealed and do not have to be refilled with distilled water In case of injury to people or damage to buildings immediately contact your supervisor Never park at fire lanes fire extinguishers and stairwells 5 2 Regulations for use Observe the traffic regulations in anormal traffic situation you will keep to the right maintain a safe distance depending on your speed you will maintain a safe speed so you are able to maintain in complete control of your vehicle and trailer s Make sure you keep a good overview of the area where you are driving and observe the safety regulations At crossings and locations where there is no good view lower your speed and give a warning signal Drive slowly on narrow lanes Avoid bends if necessary and be careful on small hills thresholds etc Reduce speed in case of sharp bends The Multi Mover M may only be driven at speeds that allow you to stop in time e g if an obstacle is standing in or entering the driving area Accelerating stopping steering making turns should always be performed quietly so that the stability of the trailers to be towed is not endangered Your conduct while driving must be polite and safe Always be careful when the vehicle is
18. riginal parts that have not been supplied by us 4 2 Operator Only persons who have had a thorough internal theoretical and practical training for driving the Multi Mover M are allowed to drive with the Multi Mover M The training programme should cover the application possibilities and the limitations the control and operating components the safety regulations daily and periodical maintenance The operator must be fully familiar with the content of this user manual People could receive or cause serious injury if the Multi Mover M is operated by unauthorized persons persons younger than 16 years of age persons of whom it may be expected that they are not sufficiently aware of the dangers of the Multi Mover M 4 3 Responsibility of the operator Operators must strictly observe the safety regulations which are included in chapter 3 and the same applies to the other rules of conduct elsewhere in this user manual 4 4 Inspection prior to putting into operation In addition to good maintenance the operator of the Multi Mover M must pay attention to the following aspects after each work period check whether there is any damage on the outside of the vehicle check the tow eye and tow pin or coupling point for bends or damage check whether the batteries are sufficiently charged drive forward and backward and check the operation of the brake check while driving slowly the full manoeuvrability of the M
19. t warns against a general or particular hazard The lower part indicates what type of hazard is being warned against and will explain what you must do MULTI MOVER M 2 TECHNICAL DESCRIPTION 2 1 Designation identification and description Designation MULTI MOVER M Identification type plate on the encasing Description vehicle on two drive wheels and a swivel wheel suitable as towing device optionally provided with an upward and downward moving coupling point for instance in order to couple the pole of a trailer and possibly to lift it drive while walking by using the driving switches on the steering handle Accessories The following parts are delivered separately with the vehicle The vehicle s operation manual Acid weighing unit optional Load report booklet optional Manuals for possible options 2 2 Technical information and dimensions Standard Maximum traction load kg 1800 Length x width x height mm 1700 x 810 x 1220 Weight batteries excl kg 60 Speed empty km h 0 5 Maximum slope angle with without load 4 12 Wheels driven standard 15x 6 00 6 4 ply Tyre pressure bar 2 1 Wheel solid 4 00 8 rim size 3 000 Swivel wheel mm 200 mm Fuse drive Amp 70 Fuse controls Amp 3 Brake hand electromagnetic tie rod Motor W 500 24Volt Battery Amps hour 26 20h Battery charger min Amps 24V 5A trickle charger automatic stop 2 3 Packaging loading unloading towing recycling Packaging The M
20. tely empty It is also not good to continue charging a battery that is almost full If the Multi Mover M is out of operation for a longer period we recommend keeping the battery charger connected it will automatically keep the battery in a charged condition The charger will blink if the handbrake button is off see fig 3 Charging location The charging location must be well ventilated because very explosive gases detonating gas are continuously released during charging Avoid open fire or sparks at the charging location while charging During charging an explo sive gas may be released The battery charger optional operates fully automatically i e the charger is equipped with an electronic system that will check the charging status and act accordingly Check whether the supply voltage to the battery charger corresponds with the voltage stated on the battery charger Some instructions for battery use and maintenance Charging 1 Insert the plug of the battery charger into the connection on the encasing and connect the battery charger to the mains 2 In the second phase the automatic battery charger will charge all elements at maximum voltage MULTI MOVER M 11 in the final phase the battery charger will stop The battery charger will switch off automatically Premature wear of the battery lf the batteries are used incorrectly it is possible that they wear quickly Premature wear is not an error in production and is t
21. than 1 cm long 3 Dirty or worn collector motor 3 Clean or have it overhauled or replace it 4 Relay does not come in properly due to contamination or defect 4 Clean or replace C Speed cannot be controlled properly or it drives at high speed immediately 1 Speed controller defective 1 Replace 2 Relay defective 2 Replace In case of a failure not mentioned in the list above please contact your dealer Note In the warranty period it is absolutely prohibited to perform repairs changes and modifications or anything like that to the Multi Mover M the warranty will become invalid 001 Battery state amperage 009 Swivel wheel 002 Drive motor 010 ALe for benefit of drive wheels 003 Carbon brush set 011 Battery plug 004 Relay 012 Female plug for battery plug 005 Speed switch 013 Fuses set 006 Ignition lock 014 Main fuse 007 Reverse switch forward reverse 020 Symbol stickers 008 Drive wheel MULTI MOVER M 15 10 EC DECLARATION OF CONFORMITY IA according to Appendix 11 A of the Machinery Directive Wij Multi Mover Europe BV Boomsestraat 38 6613 AH Balgoij HJ van Haren Authorized compiler of the technical file Multi Mover M declare at our own full responsibility that the Multi Mover M to which this declaration applies is in conformity with the provisions of the following directive s 2006 42 EC and is in conformity with the following standard s or other standardizing document s NEN EN ISO 12100 Safet
22. ulti Mover M check the jam safety on the steering handle by pressing the safety switch 2 fig 2 the Multi Mover M should not start in that case If you establish a fault or if you have any doubts concerning the operation of the Multi Mover M you must immediately report this to your supervisor or the maintenance personnel _ i SS OO Oa i ee MULTI MOVER M 5 USE 5 1 General Always keep an eye on bystanders avoid collisions Keep as far to the right as possible and maintain distance Never overtake another vehicle driving in the same direction at crossings in small passages or on other dangerous places Make sure you keep a good view on the path that you are driving keep an eye on traffic and people and observe the safety regulations Caution Hazard of serious injury due to unwanted movements on slopes as result of insufficient traction force and brake force of the Multi Mover M Never drive onto a slope or another obstacle at an angle or crosswise Only ever drive on and off a slope at a right angle The Multi Mover M may also tip over if the bends are taken at a speed that is too high Maximum slope angle with without load 4 12 Passengers may not be taken along with the Multi Mover M and towed vehicle When leaving the Multi Mover M always remove the ignition keys Let someone check whether your Multi Mover M is suitable approved for driving in your environ ment you could think of an environme
23. ulti Mover M is secured with straps on support beams on a pallet surrounded by a protective cardboard box Removing the packaging Remove the clamping strips at the wheels Avoid injury and damage as a result of incorrect placement of the lift truck s lift forks Loading and unloading If the Multi Mover M has to be moved by means of a lift truck the lift forks must be placed at the heaviest part at the rear of the Multi Mover M between the 2 large wheels Towing Caution Avoid serious damage to the drive the Multi Mover M may only be moved or towed if the hand brake tie rod round black button on the dashboard has been pulled out Recycling of the packaging Save the packaging for possible future transportations If you want to remove the packaging you must observe the local and national regulations concerning plastic waste processing OE ee MULTI MOVER M 3 SAFETY REGULATIONS Only use the Multi Mover M for the purpose for which it was designed The symbols displayed below have been attached to your Multi Mover M Get to know these symbols and make sure you know what they mean 3 1 Caution Hazard of serious injury Carefully read the user manual of the Multi Mover M so you will know exactly how to use the switches before you start driving it 3 2 Caution Hazard of injury during maintenance work Switch off the ignition and remove the ignition key disconnect the charging plug and press the emergency stop Consult t
24. y of machinery NEN EN ISO 14121 Risk assessment NEN 811 Safety distances lower limbs NEN 294 Safety distances upper limbs NEN 953 Guards fixed movable NEN 5509 User manual NEN 60204 1 Safety and electrical equipment of machines NEN EN IEC 60439 1 Switch boxes ISO 11684 Symbols Netherlands Balgoij Jan 2014 HJ van Haren Country city and date of issue Name and signature or equivalent authentication by authorized person MULTI MOVER M 16

Download Pdf Manuals

image

Related Search

Related Contents

Weider WEBE5457 User's Manual  Craftsman Dual-Stage Snow Blower Tractor Attachment Owner's Manual      Kingston Brass HDR314165 Installation Guide : Free Download, Borrow, and Streaming : Internet Archive  Visualizar en PDF  PGK Cellule à gaz  Harbor Freight Tools 3 HP 145 PSI Cast Iron Twin Cylinder Air Compressor Pump Product manual    

Copyright © All rights reserved.
Failed to retrieve file