High Resolution Day & Night IR Camera SIR
Contents
1. 485 CONTROL TERMINAL 2 The case which it controls from the DVR or System Controller It connects the RS 485 CONTROL TERMINAL in the connection terminal of 485 control boards which are connected with the DVR or System Controller 485 CONTROL BOARD CONNECTION TERMINAL RS 485 CONTROL TERMINAL CONNECTION TERMINAL WHITE TRX CONNECTION TERMINAL BLACK TRX Please must be used adaptor that meets the standard requirement Please connect the power after installation When you construct external control systems for a camera control please use to the PELCO D PROTOCOL When you connecting to RS 485 CONTROL TERMINAL please peel off the outer skin inside the RS 485 CONTROL TERMINAL condition and speed control WHITE BALANCE control MANUAL BACKLIGHT 0FF MIDDLE Backlight compensation HIGH AGC Auto Gain control eorr NORMAL e HIGH SSNR eorr LOW MIDDLE Samsung super noise reduction HGH SENS UP Low illuminance eorr AUTO CAMERA ID MOTION DET PRIVACY SPECIAL COMM ADJ IMAGE ADJ IR MODE RESET RETURN DAYNIGHT EXIT Settings can be made using the RS 485 communication Please refer 14 pages RS 485 communication control and connect to the RS 485 control terminal TRX TRX 1 When use SCC 3100A PELCO D Protocol setting method lt SETUP SYSTEM MENU gt PTZ selection PTZ SETUP2 selection 1 MODEL PTZ ID PELCO D Pro2. OSD control doesn t operate gt Please confirm whether communication setting method and RS485 control terminal connection fit POWER DC12V 10 460mA 5 SW LED ON Sensor 1 3 inch Sony Super HAD CCD Total Pixels 811 H x 508 V 795 H x 596 V Effective Pixels 768 H x 494 V 752 H x 582 V Scanning System 2 1 Interlace Synchronization Internal Fixed Frequancy H 15 734 KHz V 59 94 Hz H 15 625 KHz V 50 00 Hz T Resolution 520 Lines Color 570 Lines B W Video Output CVBS 1 0Vp p 750 50 dB AGC Off Weight ON SIN Y signal Min LED ON O Lux Illumination LED OFF 0 3 Lux Color 0 002 Sens up F1 2 Visibility Range IR LED ON Indoor Outdoor 30m IR LED number 24EA Dust Rain Resistance IP65 Day amp Night ICR AUTO COLOR BAW Gain Control NORMAUHIGH OFF Selectable White Balance ATW 1800 K 10 500 K AWC Manual Electronic shutter speed 1 60 Fixed Flickerless 1 50 Fixed Flickerless Back Light Compensation LOW MIDDLE HIGH OFF Selectable SSNR LOW MIDDLE HIGH OFF Selectable Sens Up AUTO OFF selectable limit X2 X128 OSD RS485 Control Camera Title OFF ON Displayed 15 characters Camera ID 255 ID Selectable Motion Detection ON OFF 4 Programmable Zones Communication RS 485 9600 192
3. light outdoor sodium vapor lamp or inside tunnels AWC Auto White Balance Control Please press the SETUP button while the camera is directed at a piece of white paper to obtain the optimum state under current illumination If the environment including the light source is changed you have to adjust the white balance again MANUAL The manual adjustment mode enables finer adjustment Please select ATW or AWC first Please change to manual adjustment mode and press the SETUP button Please set the appropriate color temperature and then increase or decrease the red and blue color values while monitoring the color changes on the object Notes Under the following conditions the WHITE BALANCE function may not operate properly In such cases please select the AWC mode 1 When the object s surroundings have a very high color temperature Ex a clear sky and sunset 2 When the object s surroundings are dark 3 If the camera directly faces a fluorescent light or is installed in a place where there are considerable changes in illumination the WHITE BALANCE function may become unstable Q COLOR CCD CAMERA 20 User s Manual BACKLIGHT Backlight Compensation When there is a strong backlight behind the object clear images of the background as well as the object can still be obtained by using the BACKLIGHT function 1 Please position the arrow to point to BACKLIGHT on the SETUP menu by using the UP and DOW
4. means that there is a sub menu which can be selected by pressing the SETUP button elf appears at the mode item it means that there is no mode available to be selected This function is used to adjust the brightness of the screen 1 When the SETUP menu is displayed on the screen please position the arrow to point to LENS by using the UP and DOWN buttons 2 Using the SETUP button you can control the brightness of the screen P i LENS 3 Please press the SETUP button if you wish to return to the previous menu PBRIGHTNESS mumiju 35 Press Set to Return Because SIR 4150 uses built in dc lens shutter speed is fixed at 1 60 basically P 2 SHUTTER O Shutter speed is fixed at 1 60 1 50 FLK Please select FLK mode when flickering occurs on the screen due to an imbalance between illumination and frequency NTSC Model 1 100 PAL MODEL 1 120 Operating Your Camera WHITE BALANCE control The screen color can be adjusted by using the WHITE BALANCE function 1 Please position the arrow to point to WHITE BAL on the SETUP menu by using the UP and DOWN buttons 2 Please select the mode you wish to operate by pressing the LEFT or RIGHT button SETUP 1 LENS Dee 2 SHUTTER cu p gt S WHITE BRL ATW 4 BACKLIGHT OFF Please select one of the 3 modes below ATW Auto Tracking White Balance This mode can be used within the color temperature range 1 800 K 10 500 K Ex fluorescent
5. use one of the following methods 1 Remove the front glass of Housing before installing the camera 2 To keep the front glass of Housing remove the front cover and then put the camera close to the front glass Warning Attention Special Mark Messages A Ignoring this information may result in A Ignoring this information may result in death or or serious personal injuries material loss or personal injuries O Indicates Never Allowed Q Indicates No Disassembling Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal COLOR CCD CAMERA 6 User s
6. 00 38400 and 57600bps is selectable Pelco D Protocol is available Mirror ON OFF Privacy ON OFF 4 Programmable Zones Sharpness ON OFF Level Adjustable LENS X2 5 Vari Focal Lens F1 2 f 3 8mm 9 5 mm Operating Temperature Humidity 10 C to 50 C 30 to 80 Dimension 7A W x 74 H x 134 5 D mm Weight 585g DECLARATION OF CONFORMITY Application of Council Directive s 89 336 EEC Manufacturer s Name SAMSUNG TECHWIN CO LTD Manufacturer s Address SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 120 European Representative Name European Representative Address Equipment Type Environment CCTV Camera Model Name SIR 4150P Beginning Serial NO S8090001 Year of Manufacture 2008 09 01 Conformance to EN 50081 1 1992 EMC Directive 89 336 EEC and 92 31 EEC EN 50130 4 1996 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer SAMSUNG TECHWIN CO LTD Legal Representative in Europe Signature Flan deg ie Signature Full Name HAN SEUG KIM Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON KOREA Place Date 2008 09 01 Date SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon dong Jungwon gu Seongnam si Gyeonggi d
7. 8114444244 SSNR Samsung Super Noise SENS UP Low illumina aid e SPECIAL CE e EXIT oeiee NG e Troubleshooting Be isisa e Specifications B IM NI PAPER AA pbdg 2 High Sensitivity MAD The built in high sensitivity COLOR CCD enables a clear image even in OLux B W IR LED ON or lower illumination EAS 3 Resolution SX Pag A Featuring 520TV line horizontal resolution in color mode and 570TV line horizontal resolution in BW mode The camera features Sony s 410 000 pixel CCD and capture clean noiseless high quality image vba Ni NA DAY amp NIGHT ICR A LS Pree This camera has a function that automatically selects the mode that is appropriate for daytime or night time a ditions NG 2 The COLOR mode operates in daytime conditions to m AN fide optimum colors and BW mode operates in night itions to enhance the definition of the image Oh Paia phdg Outdoor Visibility range 30M PENA The IR LEDs of the SIR 4150 automatically illuminates viewing area in the extreme darkness allowing the camera a long range visibility of up to 30 meters This function that prevent short distance saturation in case of IR LED is lighted discrimination of the subject is possible within a short distance phla N VA p RS 485 Function A A Pyga Use RS485 communication and OSD menu control does possibility to remote qn syne its Gan With dust and rain resistant ae installed outside under buildi
8. 8400bps 57600bps UART MODE Configure parity bit to NONE EVEN or ODD Data bit is set to 8bit and stop bit to 1bit END C Notes Please set CAM ID of CAMERA and external communication control device equally IMAGE ADJ Includes image quality or special function factors e MIRROR Sets a horizontal image inversion COLOR CCD CAMERA 29 User s Manual MIRROR OFF MIRROR ON SHARPNESS The outline of the video image becomes cleaner and more distinctive as the level of SHARPNESS increases If the level goes up excessively however it may affect the video image and generate noise IR MODE When IR LED is turned on in B W the objects can be clearly identified due to the function that decreases screen saturation of objects within a short distance OFF disabled Used to view clearly in dark environments such as warehouse and outer area ON IR MODE enabled TOP DOWN LEFT RIGHT Adjust the range according to the location of objects LEVEL Select LOW when objects appears within a short distance or select HIGH when objects appears within a long distance on the screen press SEL to Return IR MODE function does not work in D amp N COLOR mode When IR MODE level is set to LOW saturation at a short distance decreases while video image becomes darker RESET Returns to the level which was set by the manufacturer for shipment RETURN Returns to the SETUP menu Saves all the set
9. Manual Q Precautions Do not install under extreme Do not install in high humidity temperature conditions environment WF Pasa Use only under temperature conditions May lower image quality between 10 C and 50 C Provide good ventilation when using in high temperature conditions Do not install under unstable lighting conditions Avoid touching the camera lens Severe lighting changes or flickering may The lens is the most important component hinder normal camera operation of the camera Be careful not to smear it with fingerprints COLOR CCD CAMERA D User s Manual May cause a product malfunction May damage the CCD Radioactivity exposure may damage the CCD Exposure to a spotlight or an object emitting strong light may cause smear or blooming Ensure that the power source complies with normal specifications before supplying it to the camera In case of IR LED has been lighted do not lighten directly eye SIR 4150 CAMERA HOOD HOOD ADAPTOR 2EA USER S MANUAL DC 12V 4A ADAPTOR G POWER CABLE Hood adaptor Fixing the hood onto the camera Focus lever Set focus of lens by turn the focus lever Zoom lever Set zoom magnification of lens by turn the zoom lever Front cover fixing screw Notes e Adjust to the zoom amp focus lever and then use after fixate turning lever to clockwise When you adjust to the ZOOM amp FOCUS of the lens Plea
10. N buttons 2 Please select the mode you wish to operate by pressing the LEFT or RIGHT button SETUP 1 LENS oc 2 SHUTTER 3 WUHITE BRL ATU p gt 4 BACELIGHT OFF 5 AGC NORMAL HIGH MIDDLE LOW You can adjust the sensitivity of BLC and BLC window s pista size and position So that It can achieve BLC function ll efficiently regardless of position of subject ud OFF BLC function doesn t operate BACKLIGHT OFF Notes When BW mode at night time BLC does not operate COLOR CCD CAMERA 21 User s Manual 1 Please position the arrow to point to AGC on the SETUP menu by using the UP and DOWN buttons 2 Please select the mode you wish to operate by pressing the LEFT or RIGHT button As the level of gain increases the screen gets brighter and the level of noise also increases HIGH The gain increases or decreases within the range of 6dB 34dB NORMAL The gain increases or decreases within the range of 6dB 30dB OFF The gain is fixed at 6dB HORMAL 4 1 3 Please press the SETUP button The BRIGHTNESS E can be adjusted within the range of 1 70 Brightness 4 Please press the SETUP button when all the PBRIGHINESS bebe 35 settings are complete Press Set to Return The background noise in the low light level decreases automatically as the level of gain changes 1 Please position the arrow to point to SSNR on the SETUP menu by using the UP and D
11. OWN buttons 2 Please select the mode you wish to operate by pressing the LEFT or RIGHT button p 6 SENE OFF There is no reduction in noise level SLOW Thereis a small reduction in noise level with almost no ghost image C MIDDLE The most effective mode There is a sufficient reduction in noise levels without causing much ghost image CHIGH The level of noise is reduced greatly however there is an increase in ghost image Notes When AGC is turned off SSNR does not operate SENS UP helps maintain a bright clear screen image by automatically detecting changes in the level of light in low light level conditions 1 Please position the arrow to point to SENS UP on the SETUP menu by using the UP and DOWN buttons 2 Please select the mode you wish to operate by pressing the LEFT or RIGHT button C AUTO Low light level auto mode OFF The function does not operate When SHUTTER is in the manual mode SENS UP does not operate When AGC is turned off SENS UP does not operate gt T SEHS UP 3 Please press the SETUP button when all the settings are complete The maximum storage magnification in low light level can be adjusted by pressing the SETUP button in AUTO mode X2 X128 As the magnification increases the screen gets brighter moving object gets more afterimage e f storage magnification is increased while SENS UP is operating it may cause noise and spots may appea
12. a through Break the Darkness High Resolution Day amp Night IR Camera SIR 4150 User s Manual Thank you for purchasing a SAMSUNG CCD CAMERA Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use ENGLISH Before operating the camera confirm the camera model and proper input power voltage In order to that you can understand this manual thoroughly we ll introduce our mode description W SIR 4150 SERIES NTSC MODELS PAL MODELS SIR 4150N SIR 4150P IW MODEL DESCRIPTION SIR 4150 X SIGNAL SYSTEM SIGNAL SYSTEM N NTSC MODEL P gt PAL MODEL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is A intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with li
13. as been chosen please select a position for the name display Please move the cursor onto POS and then press the SETUP button The name will appear at the top left hand A corner FRONT DOOR Ll Q Please find the position you wish to display the name by using the 4 directional buttons and then press the SETUP button 6 Please select END and then press the SETUP button to complete ID input DAY amp NIGHT ICR TYPE Select from COLOR B W or AUTO modes AUTO According to the input luminance level IR Cut Filter is automatically Switched to the appropriate mode for daytime or night time The COLOR mode is operated for daytime and it converts to BW mode for night time Operating Your Camera COLOR COLOR mode e B W BW mode Please press SETUP button to turn on or off the burst signal on BW mode S Notes e If AGC is OFF you can t select AUTO mode and B W mode When DayNight mode is set to Auto under the condition which the strong IR light is flickering periodically a malfunction of IR Cut filter may occur C MOTION DETECTION This product has a feature that allows you to observe movements of objects in 4 different areas on the screen and the words MOTION DETECTED appear on the screen when movement is detected hence a single individual can conduct supervision efficiently The camera detects an object s movement by sensing disparity of outline and level
14. gu or p are exposed to the dust and rain NE PRIVAG N V le PRIVACY masking function conceals the areas you noise ratio SIN as wel as h P aditional Function NA SENS UP MIRROR SHARPNESS MOTION DET functions are also available been improved jd y clear and sharp image display even in the da i Samsung Techwin cares for the environment at all product manufacturing stages to preserve the C environment and is taking a number of steps to provide customers with more environment friendly s products The Eco mark represents Samsung Techwin s will to create environment friendly products and indicates that the product satisfies the EU RoHS Directive eco RoHS compliant Warnings amp Cautions This information is provided to ensure your safety and to prevent any losses financial or otherwise Please read it carefully and use the product accordingly For product inquiries please contact the retail shop where you bought the camera The use of equipment such as an aerial ladder while providing after sales service shall be at your expense 9 Notes Please make sure the product is installed appropriate places where secured from flood such as under the eaves to operate properly This product is certified as IP65 standard However if there is any flood concerns it is highly recommended to use an outdoor Housing When you install the camera inside an outdoor Housing please
15. mits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes Features e Warnings amp cautions Components and Accessories Overview E Front Adjust to lens E Ajust to Lens s ZOOM and Focus Connection Wi Connecting to a monitor Wi Connecting to power Ii RS 485 Communication control Operating Your Camera LENS Adjusting to the brightness leue SHUTTER condition and speed control WHITE BALANCE control BACKLIGHT Backlight Compen i e AGC Auto Gain Control 114
16. o 462 120 Korea TEL 82 31 740 8151 8158 FAX 482 31 740 8145 www samsungcctv com www samsungtechwin com SAMSUNG TECHWIN AMERICA SAMSUNG OPTO ELECTRONICS UK LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business TOLL FREE 1 877 213 1222 FAX 1 310 632 2195 Park Chertsey Surrey KT16 OPS www samsungcctvusa com TEL 44 1932 45 5308 FAX 44 1932 45 5325 P No Z6806 0820 01D VAN 08 09
17. of brightness and color Please press the SETUP button OFF MOTION DETECTION mode is cancelled ON Any motion in the selected areas is observed Please select the area you wish to observe from the 3 areas in AREA SEL mode MOTION DETECTION Please select ON mode for the chosen area _ s umi e Please adjust the size of the area to be observed mop E bom by using the UP DOWN LEFT or RIGHT button um Please press the SETUP button to save the changes and complete the setting COLOR CCD CAMERA 28 User s Manual C Notes There is no MD output signal MD is on screen display only words PRIVACY Mask privacy area you do not wish to appear on the screen OFF Cancels the PRIVACY mode ON Operates the PRIVACY mode Please press the SETUP button Please select the area you do not wish to PRIVACY appear from the 4 areas in AREA SEL mode AU Please select ON mode for the chosen area Please adjust the size of the area to be concealed by using the UP DOWN LEFT or RIGHT button COM ADJ When wish to control CAMERA by external communication control device it is function that set up CAMERA s E sv communication states and protocol BAUD RATE 600 e CAM ID Assign ID number to the camera It is E men restricted available to set ID from 1 255 e DISP CAMID Displays CAM ID on the top left of the screen e BAUD RATE Configure baud rate from 9600bps 19200bps 3
18. r however this is normal 1 Please position the arrow to point to SPECIAL on the SETUP menu by using the UP and DOWN buttons 2 Please select the mode you wish to operate by pressing the UP or DOWN button P iG CAMERA ID OFF CAMERA ID If the ID is input the camera ID appears on the monitor 1 Please position the arrow to point to CAMERA ID by using the UP or DOWN button 2 Please select ON by pressing the LEFT or RIGHT button Acts e If OFF is selected the ID does not appear on the monitor even if it has been input gt 18 CAMERA ID OFF 3 Please press the SETUP button 4 Up to 15 letters can be used for the ID Please move the cursor to the letter you wish to choose by using the UP and DOWN button select an ID from A B Y Z a b y z 0 1 8 9 by using the UP DOWN LEFT and RIGHT buttons Please lock in the letters by using the SETUP button When the letter is locked in the cursor moves to the next space Please repeat the above to input the ID e If the wrong name has been input If you press the SETUP button after moving the cursor to CLR all the letters will be erased If you want to correct a letter please move the cursor to the arrow at the bottom left of the screen and press SET Please position the cursor above the letter you wish to correct and then move the cursor onto the letter you wish to choose and press the SETUP button 5 When a name h
19. se loosen the Front cover fixing screw and separate Front cover from the camera Mounting bracket screw hole Please use the screw hole when fixing the camera onto the mounting bracket I Please use the clamp screw as specified below 1 4 20UNC2OTHREAD L4 5mm 0 2mm SO standard or 0 197 ASA The mounting bracket can be separated and attached the top of the camera In this instance please do not tighten the screw to a depth of more than 4mm otherwise serious damage can occur to the inside of the camera Notes e This camera package does not include the mounting bracket Please refer to the user s manual for installation of the mounting bracket Power input terminal Video output terminal RS 485 control terminal 1 Please loosen a front cover fixing screw with picture and separate cover Please connect the video output terminal located on the back of the camera to the 2 Please unlock the Zoom or Focus lever to release it monitor 3 Adjust the zoom or focus lever by moving it to WIDE NEAR or TELE FAR position 4 After adjustment tighten the zoom or focus lever taking care that the adjusted CCD Camera position does not change 5 Please close cover and tighten the front cover fixing screw _ a a z r The connection method varies depending on the type of moni
20. ting menus and then exits If there are problems in operation please refer to the items below If the problem persists please contact the agent you purchased this product from Nothing appears on the screen gt Please check the power connection gt Please check the video signal line connection The video image is not clear gt Please check if the lens is clean Please clean the lens with a clean cloth or brush gt Please adjust the contrast feature of the monitor gt Please make sure that the screen is not exposed directly to a bright light Please move the camera if necessary The screen is dark gt Please adjust the contrast feature of the monitor gt If you have an intermediate device set the 750 Hi z properly and check the terminals There is a problem with the camera operation The camera surface is too hot and black stripes appear on the screen gt Please check if an appropriate power source to the camera complies with the manufacturer s standard requirement or if the voltage keeps changing Color are not quite right gt Please check the WHITE BAL setting DAY amp NIGHT AUTO B W mode doesn t Operate gt Please check if the AGC menu is set to the OFF position SENS UP function doesn t operate gt Please check if the AGC menu is set to the OFF position IR LED isn t lighted gt Isn t DAYNIGHT function setting up the color mode gt Please change the AUTO or B W mode
21. tocol selection CONTROLLER selection SERIAL selection 1 BAUD 2 DATA 3 STOP BIT 4 PARITY setting OSD button Display OSD menu on the monitor or there is a sub menu which can be selected by pressing OSD button 3k JOYSTICK It can move menu cursor by upside downward the left side and the right side Joystick do Up Down Right Left button functions according to 4 directions that move LEFT BUTTON When you use SCC 101 you can adjust the menus without changing settings For more information about how to set up connection please refer to SCC 101 manual 1 Please press the SETUP button e Settings can now be made The SETUP menu is displayed on the monitor P S WHITE BRL ATU 2 Please select any function you wish to activate by using the UP and DOWN buttons The arrow can be moved up or down by using the UP and DOWN buttons Please position the arrow to point to the function you wish to operate Select any function you Modes can be changed wish to operate by using the LEFT and using the UP and DOWN RIGHT buttons buttons 3 Please press the LEFT or RIGHT button if you wish to change mode When the LEFT or RIGHT button is pressed available values and modes are displayed in order Please keep pressing the button until you get to the mode you wish to operate 4 Please select EXIT and then press the SETUP button to finish the setting Notes e If lt appears at the mode you wish to operate it
22. tor and accessories Please refer to the user s manual for each instrument Please turn off the power when connecting e Please select Hi Z on the 750 Hi Z switch for the intermediate video TV set and Front cover fixing screw select 750 for the Intermediate device as shown in the picture below Intermediate End monitor Notes e If front cover fixing screw do not pinch it is not waterproof The recommended adaptor specification for SIR 4150N P is DC 12V 4A Please check the standard power requirement before connecting to power WHITE 485 TRX 7 BLACK 485 TRX As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera Standard voltage for camera operation DC 12V 10 There may be some deviation in voltage drop depending on the type of wire and the manufacturer Notes CONTROL TERMINAL SPEC WHITE TRX RS 485 BLACK TRX RS 485 Using a RS 485 communication it will be able to control the OSD menu at the SAMSUNG TECHWIN System Controller or DVR 1 The case which it controls from the PC Using a RS 485 converter It connects to RS 485 CONTROL TERMINAL outside camera and serial cable EX SERIAL PORT OF THE PC COM1 SERIAL CABLE RS 485 CONVERTER RS
Download Pdf Manuals
Related Search