Bristol ControlWave Industrial Ethernet Real
Contents
1. Top View of the aul fr 5 port w fiber Switch User Manual Page 8 of 13 Section 6 Switching Features Switch User Manual Switching Features Here s a brief explanation of the features found in the Industrial Ethernet Switches documented by this manual 10BaseT and 100BaseTx Autodetection Standard Ethernet 10BaseT has a maximum speed of 10 Mbps megabits per second Fast Ethernet 100BaseTx has a maximum speed of 100 Mbps The RJ45 ports on the Industrial Ethernet Switches automatically support both types 100BaseFX multimode and singlemode fiber optic port The fiber optic port found on some models is classified as 100BaseFX and supports 100 Mbps operation only Both multimode and singlemode models are available Multimode allows for multiple wavelengths over a cable with a core diameter of typically 50 or 62 5 microns The maximum distance for multimode is 2 km Singlemode uses a single wavelength and cable core diameter of around 10 microns which allows for a maximum distance of 15 km or more 1 4 Gbps combined bandwidth With full duplex and 100BaseTX or 100BaseFX communications each port can provide a full 200 Mbps of data throughput 1K MAC addresses with automatic learning aging and migration Each Ethernet device inserts its unique MAC address into each message it sends out The port on the switch used for a given MAC address is automatically learned when a fr2. 11 Section 8 Service Information Page 13 ce O A This manual applies to the following products 5 port switch 4 1 fiber single mode switch SM 4 1 fiber multi mode switch MM Page 1 07 03 01 INSTALLATION AND HAZARDOUS AREA WARNINGS These products should not be used to replace proper safety interlocking No software based device or any other solid state device should ever be designed to be responsible for the maintenance of consequential equipment or personnel safety In particular no responsibility for damages either direct or consequential that result from the use of this equipment in any application will be taken by the distributor of this product All power input and output I O wiring must be in accordance with Class I Division 2 wiring methods and in accordance with the authority having jurisdiction WARNING EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS 1 DIVISION 2 WARNING EXPLOSION HAZARD WHEN IN HAZARDOUS LOCATIONS DISCONNECT POWER BEFORE REPLACING OR WIRING UNITS WARNING EXPLOSION HAZARD DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This e
3. are defined and or determined by applicable federal state and or local law regulations or codes Such party agrees to indemnify Bristol Babcock and save Bristol Babcock harmless from any liability or damage which Bristol Babcock may incur or suffer due to such party s failure to so act ELECTRICAL GROUNDING Metal enclosures and exposed metal parts of electrical instruments must be grounded in accordance with OSHA rules and regulations pertaining to Design Safety Standards for Electrical Systems 29 CFR Part 1910 Subpart S dated April 16 1981 OSHA rulings are in agreement with the National Electrical Code The grounding requirement is also applicable to mechanical or pneumatic instruments that include electrically operated devices such as lights switches relays alarms or chart drives Bristol Babcock 1100 Buckingham Street Watertown CT 06795 Telephone 860 945 2200 WARRANTY Bristol warrants that goods described herein and manufactured by Bristol are free from defects in material and workmanship for one year from the date of shipment unless otherwise agreed to by Bristol in writing Bristol warrants that goods repaired by it pursuant to the warranty are free from defects in material and workmanship for a period to the end of the original warranty or ninety 90 days from the date of delivery of repaired goods whichever is longer Warranties on goods sold by but not manufactured by Bristol are expressly limited to the ter
4. simply broadcast all messages out all ports Switches intelligently route messages only out the appropriate port All the devices described in this manual are Switches Ethernet The 5 port fiber MM has one pair of FX multimode SC connectors that support a maximum p p Fiber Wiring segment length of 2 km The 5 port fiber SM has one pair of FX singlemode SC connectors that Guidelines support a maximum segment length of 15 km The fiber optic port on the switch is comprised of a pair of SC connectors which are labeled with RX and TX When making your fiber optic connections make sure that the transmit TX port of the switch connects to the receive RX port of the other device and the receive RX port of the switch connects to the transmit TX port of the other device The ACT LNK LED will be ON solid when you have made a proper connection Full or Half The RJ45 ports will auto sense for Full or Half duplex operation No user configuration is Duplex necessary The fiber optic port has a movable slide switch that allows you to select either Full or Half duplex operation This slide switch is located next to the fiber optic connector See diagram Operation Note You must cycle power to the switch after changing the slide switch position E I m E Ss Full Duplex a Half Duplex E E E E
5. to 3 48 in lbs max 5 port fiber switch 12 AWG max tighten to 5 3 in lbs max The Industrial Ethernet Switch meets the following standards Electrical safety UL 508 CSA C22 14 EN61010 1 IEC1010 EMI emissions FCC part 15 ICES 003 EN55022 Class B EMC immunity EN61326 1 EN61000 4 2 3 4 and 6 Hazardous locations UL 1604 CSA C22 2 213 Class 1 Div 2 Groups A B C D Cenelec EN50021 Zone 2 Install the Industrial Ethernet Switch in accordance with local and national electrical codes Lightning Danger Do not work on equipment during periods of lightning activity Do not connect a telephone line into one of the Ethernet RJ45 connectors Page 3 of 13 Section 2 LED Indicators Overview The Industrial Ethernet Switches have communication LEDs for each port and a power LED Refer to the pictures below for the typical location of these LEDs The exact location of these LEDs may vary between the different models nan me e e e RX TX Fiber Optle Port E A0 ACT 10 ACT do ACT 10 ACT f nL ENK tool LW 100 ENK 100 tec Full Duplex D Half Duplex O ACTILAK LED OFF ne tink ON linked f Blink activity i 7 a ACTS ti LNK 100 ACTI 10 A i A ia act 10 LHK LAKE 100 ACTILAR LED DFF ee link iin Blink aetevity TATOO LED OM00 LED OFF 10 Mbps ON 100 Mbps iene Industrial Etherne
6. 860 945 3875 A BBI Repair Dept representative will return call or other requested method with a RA number B E MAIL Accessing the form GBU 138 01 via the Bristol Babcock Web si te www bristolbabcock com and sending it via E Mail to brepair bristolbabcock com A BBI Repair Dept representative will return E Mail or other requested method with a RA number C Mail Mail the form GBU 13 01 to Bristol Babcock Inc Repair Dept 1100 Buckingham Street Watertown CT 06795 A BBI Repair Dept representative will return call or other requested method with a RA number D Phone Calling the BBI Repair Department at 860 945 2442 A BBI Repair Department representative will record a RA number on the form and complete Part I then send the form to the Customer via fax or other requested method for Customer completion of Parts II amp III A copy of the completed Repair Authorization Form with issued RA number should be in cluded with the product being returned This will allow us to quickly track repair and return your product to you Bristol Babcock Inc Repair Authorization Form Providing this information will permit BBI to effectively and efficiently process your return Completion is required to receive optimal lead time Lack of information may result in increased lead times Date RA SH_ Line No Standard Repair Practice is as follows Variations to this is Please be aware of the Non warranty standard charge p
7. Cl ControlWave IES Instruction Manual ControkV ave Industrial Ethernet Real time Switches 5 Port Switch BB GT 5ES 1 4 1 Fiber Single mode Switch SM BB GT 5ES 2CS 4 1 Fiber Multi mode Switch MM BB GT 5ES 3SC Industrial Ethernet Real time Switch Bristol Babcock NOTICE Copyright Notice The information in this document is subject to change without notice Every effort has been made to supply complete and accurate information However Bristol Babcock assumes no responsibility for any errors that may appear in this document Request for Additional Instructions Additional copies of instruction manuals may be ordered from the address below per attention of the Sales Order Processing Department List the instruction book numbers or give complete model number serial or software version number Furnish a return address that includes the name of the person who will receive the material Billing for extra copies will be according to current pricing schedules ControlWave is a trademark of Bristol Babcock Other trademarks or copy righted products mentioned in this document are for information only and belong to their respective companies or trademark holders Copyright c 2001 Bristol Babcock 1100 Buckingham St Watertown CT 06795 No part of this manual may be reproduced in any form without the express written permission of Bristol Babcock IMPORTANT READ INSTRUCTIONS BEFORE STARTING Be sur
8. Manual Page 5 of 13 Section 4 Power Wiring Overview Industrial Ethernet Switches can be powered from the same DC source that is used to power your I O devices 10 to 30 VDC needs to be applied to terminals 2 and 3 Refer to the wiring diagram below Cy Be Oe oe e a ACT of oacty ao Aa agf acts woe act wo PAW LWE 100 LNK 100 LNK i00 LNK 10 LMK 100 Ustink Pori lodustrial Ethernet Real time Switch 10 40 VDC Screw Torque The screw terminals should be tightened as follows For the 5 port switch tighten screw terminals to a maximum 3 48 in lbs 0 4 Nm For the 5 port fiber switch tighten screw terminals to a maximum 5 3 in lbs 0 6 Nm Switch User Manual Page 6 of 13 Section 5 Ethernet Wiring Overview The Industrial Ethernet Switches provides connections to Ethernet devices on the factory floor Typically the uplink port or fiber port is used to connect to another Ethernet switch or hub that is connected to the main Ethernet backbone The other four Ethernet ports are then connected to Ethernet devices such as PLCs Ethernet I O or industrial computers Electrical isolation is provided on the Ethernet ports for increased reliability Please follow normal 10 100BaseT x and 100BaseFX Ethernet wiring practices when installing the Industrial Ethernet Switch Main Ethernet Backbone Oftice grade switch i ndustrial switch Ethernet Switch Installation i hoy FACTORY FLOOR ct
9. al information as well as software updates are available in this area To access our web site go to bristolbabcock com services techsupport Page 13 of 13 READER RESPONSE FORM Please help us make our documentation more useful to you If you have a complaint a suggestion or a correction regarding this manual please tell us by mailing this page with your comments We are dedicated to providing you correct complete and useful documentation DOCUMENT NUMBER CI ControlWavelES TITLE ControlWave Industrial Ethernet Real time Switches Customer Instruction Manual ISSUE DATE JULY 2001 COMMENT COMPLAINT Mail this page to Bristol Babcock Inc 1100 Buckingham Street Watertown CT 06795 Attn Technical Publications Group Dept 315 Customer Instruction Manual ClI ControlWavelES Issue 7 2001 Control ave industrial Ethernet Real time Switches Bristol Babcock Inc an FKI company 1100 Buckingham Street Watertown CT 06795 Telephone 860 945 2200
10. ame is received from that address Once an address is learned the switch will route messages to only the appropriate port instead of broadcasting messages out all ports like a hub A time stamp is also placed in memory when a new address is learned This time stamp is used with the aging feature which will remove unused MAC addresses from the table after 300 seconds If a device moves the associated port on the switch will be changed migrated as needed Up to 1 024 MAC addresses can be stored and monitored at any time Auto sensing speed and flow control The RJ45 ports of the Industrial Ethernet Switches will auto negotiate with the connected device to determine the optimal speed 10 Mbps vs 100 Mbps and flow control for each port Automatic power saving If there is no cable on a port most of the circuitry for that port is disabled to save power Backoff operation The Industrial Ethernet Switch will drop a packet after 16 collisions Back pressure for half duplex The Industrial Ethernet Switch will apply back pressure when necessary with half duplex operation This back pressure will reduce congestion on busy networks Broadcast storm protection Broadcasts and multicasts are limited to 25 of the available bandwidth Buffering SRAM is used for buffering the messages There are 1024 128 bytes each buffers available Each port is allocated 205 buffers Page 9 of 13 Switch User Manual Unmanaged operation The Indus
11. e that these instructions are carefully read and understood before any operation is attempted Improper use of this device in some applications may result in damage or injury The user is urged to keep this book filed in a convenient location for future reference These instructions may not cover all details or variations in equipment or cover every possible situation to be met in connection with installation operation or maintenance Should problems arise that are not covered sufficiently in the text the purchaser is advised to contact Bristol Babcock for further information EQUIPMENT APPLICATION WARNING The customer should note that a failure of this instrument or system for whatever reason may leave an operating process without protection Depending upon the application this could result in possible damage to property or injury to persons It is suggested that the purchaser review the need for additional backup equipment or provide alternate means of protection such as alarm devices output limiting fail safe valves relief valves emergency shutoffs emergency switches etc If additional information is required the purchaser is advised to contact Bristol Babcock RETURNED EQUIPMENT WARNING When returning any equipment to Bristol Babcock for repairs or evaluation please note the following The party sending such materials is responsible to ensure that the materials returned to Bristol Babcock are clean to safe levels as such levels
12. et Switch can be snapped onto a standard DIN rail EN50022 or screwed directly to a flat panel Refer to the mechanical drawings below Note The Ethernet connections for the 5 port switch come out the face of the unit However the Ethernet connections for the 5 port fiber switch come out the top Make sure to allow enough room to route your Ethernet cables balls geg k a LO ler3 C 79cm et 2 92 eo L7 42crl LO 64crml j ri Of O26 16 CO a ol al ACTE 10 aCe do ACT ibs ACE iD ACT ar LHE 100 LHK 103 LHE 86100 LHK 10C LHE 10D Uplink Fa aie gt 7 L6 05cr 8 05cn Ee fod A PeF ndustrial Ethernet IK Real time Switch L E 7 al EN zii T FA 50022 o1 B i T CA0 4 as May height off i clear for 447 C 1 aacml panel is 1 75 ey Bvseren 475207 cr ee Er 4 24cm 5 port switch 1 10 T 0e 0 6 cal CPA _ B LO 71cm nee Fj l eae let 025 LF 42 crl OOG OGO OO OS LO 64crl th age Lie aga Lie 109 Le EO LN FER E Tier Bol 3 17 3 17 Le 0Ser 2 05cm Industrigl Ethernet T Real time Switch e DIN a4 EW paar 50022 mee E o l 1 a045i Mov hetghi aff i clegar for 447 Lll enl panel fg 1 75 E B acrew 475 LIE07ceal 48 rl T pa ewer 4 1 fiber port switch Switch User
13. henmnet enabled S ee js Control Cabinet Computer Ethernet VO Ethernet Ethernet RJ45 Cable Type RJ45 Wiring Use data quality not voice quality twisted pair cable rated category 5 with standard RJ45 eT 3 Ma connectors For best performance use shielded cable Please note that these cables are available as straight thru or cross over configurations The following is a guide for when to use each type Ethernet Switch Cable Type Ethernet Switch Cable Type STANDARD Port to to Use UPLINK Port to to Use Straight thru PC card Cross over Ethernet I O Straight thru Ethernet I O Cross over Straight thru PLC Cross over Other Ethernet enabled Straight thru Other Ethernet enabled Cross over devices devices Uplink port on another Straight thru Standard port on another Straight thru switch or hub see note switch or hub Note Some Ethernet switches and hubs have a settable switch on their Uplink port that will change how the port is internally wired Make sure this switch is set in the To Hub Switch MDI position as opposed to the To PC MDI X position Switch User Manual Page 7 of 13 Ethernet Connector Pin Positions Ethernet Connector Pin Assignments RX Cable Distance The maximum cable length for 10 100BaseT x is typically 100 meters 328 ft Refer to the following chart for some general guidelines PLC Ethernet I O PC etc 100 meters 328 feet Note Hubs and Switches are different devices Hubs
14. ike an Ethernet hub that broadcasts all messages out all ports the Industrial Ethernet Switches will intelligently route Ethernet messages only out the appropriate port The major benefits of this are increased bandwidth and speed reduction or elimination of message collisions and deterministic performance when tied with real time systems The Industrial Ethernet Switches support both 10BaseT 10 Mbps and 100BaseTx 100 Mbps on their RJ45 ports Each of these ports will independently auto sense the speed allowing you to interface to regular or fast Ethernet devices Some models also have a 100BaseFX 100 Mbps fiber optic port Refer to Section 6 for more information on Industrial Ethernet Switch operation and features These general specifications apply to the Industrial Ethernet Switches Refer to Section 7 for complete technical specifications Ports models vary 10 100BaseT x Shielded RJ45 100BaseFX SC connectors Required Voltage 10 30 VDC see Section 7 for current draw for each model Ethernet Standards IEEE 802 3 10BaseT 802 3u 100BaseTX 802 3x Full Duplex Ethernet Protocols All standard IEEE 802 3 protocols supported Speed Per Port RJ45 10 or 100 Mbps half duplex 20 or 200 Mbps full duplex Fiber 100 Mbps half duplex 200 Mbps full duplex Ethernet Isolation 1200 Volts RMS for 1 minute Operating Temp 40 to 85 C Humidity 5 to 95 non condensing screw Terminals 5 port switch 14 AWG max tighten
15. ms of the warranties given by the manufacturer of such goods All warranties are terminated in the event that the goods or systems or any part thereof are 1 misused abused or otherwise damaged 11 repaired altered or modified without Bristol s consent 411 not installed maintained and operated in strict compliance with instructions furnished by Bristol or iv worn injured or damaged from abnormal or abusive use in service time THESE WARRANTIES ARE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION WARRANTIES AS TO MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND NO WARRANTIES EXPRESS OR IMPLIED NOR ANY REPRESENTATIONS PROMISES OR STATEMENTS HAVE BEEN MADE BY BRISTOL UNLESS ENDORSED HEREIN IN WRITING FURTHER THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF No agent of Bristol is authorized to assume any liability for it or to make any written or oral warranties beyond those set forth herein REMEDIES Buyer s sole remedy for breach of any warranty is limited exclusively to repair or replacement without cost to Buyer of any goods or parts found by Seller to be defective if Buyer notifies Bristol in writing of the alleged defect within ten 10 days of discovery of the alleged defect and within the warranty period stated above and if the Buyer returns such goods to Bristol s Watertown office unless Bristol s Water town office designates a differen
16. ol Babcock hardware to radios contact Communication Technologies in Orlando FL at 407 629 9463 or 407 629 9464 Telephone Support Non Technical Questions Product Orders etc Questions of a non technical nature product orders literature requests price and delivery information etc should be directed to the nearest sales office listed below or to your Bristol authorized sales representative Major U S Sales Offices Major International Sales Offices Watertown CT 860 945 2262 Bristol Babcock Ltd UK 441 562 820 001 Birmingham AL 205 980 2010 Bristol of Canada 416 675 3820 Ontario CA 909 923 8488 Bristol Babcock Asia Pacific 61 8 9455 9955 Farmington NM 505 327 3271 BBI S A de C V Mexico 525 254 2131 Houston TX 7138 685 6200 Richardson TX 972 238 8935 Please call the main Bristol Babcock number 860 945 2200 if you are unsure which office covers your particular area Visit our Site on the World Wide Web For general information about Bristol Babcock and its products please visit our site on the World Wide Web at www bristolbabcock com Switch Industrial Ethernet Real time Switches Industrial Ethernet Real time Switch Contents at a Glance Section 1 General Information Page 3 Section 2 LED Indicators Page 4 Section 3 Installation Page 5 Section 4 Power Wiring Page 6 Section 5 Ethernet Wiring Page 7 Section 6 Switching Features Page 9 Section 7 Technical Specifications Page
17. quipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Copyright amp Trademarks Copyright 2001 All Rights Reserved Note All information in this document is subject to change without notice Switch User Manual Page 2 of 13 Section 1 Overview Operation Performance Specifications Standards and Safety CE SAM Aus LISTED VAN A Switch User Manual General Information This manual will help you install and maintain the Industrial Ethernet Switches These unmanaged switches are extremely easy to install and operate because little or no user configuration is required Once the Ethernet connections are made and the unit is powered up it will immediately begin to operate Unl
18. r and the unit will immediately begin to operate Protocol independent The Industrial Ethernet Switch will work with all popular Ethernet protocols and networks such as TCP IP the Internet IP UDP NetBEUI and many more It is compatible with all protocols that run over standard Ethernet IEEE 802 3 In fact it will support packets of different protocols simultaneously Page 10 of 13 Section 7 Technical Specifications Technical Here are the technical specifications for the Industrial Ethernet Switches covered by this manual Specifications 10 100BaseT x Ports 10 100BaseT x ports Protocols supported Ethernet compliancy Auto sensing operation Auto negotiating Flow control Ethernet isolation Plug and play Cable requirements Twisted pair Cat 5 shielded recommended Max cable distance 4 1 fiber port switch MM multimode 100BaseFX ports Fiber port mode Fiber port connector Duplex SC Optimal fiber cable 50 125 62 5 125 um Center wavelength 1300 nm TX output power RX input sensitivity Maximum distance Half and full duplex Ethernet compliance Eye safety a 4 1 fiber port switch SM singlemode 100BaseFX ports Fiber port mode Fiber port connector Optimal fiber cable Center wavelength TX output power RX input sensitivity Maximum distance Half and full duplex Ethernet compliance Eye safety E n i Switch User Manual Page 11 of 13 Forwarding mode Store and forward Memory bandwid
19. ractice may be requested in the Special Requests section e There is a 100 minimum evaluation charge which is e Evaluate Test Verify Discrepancy applied to the repair if applicable V in returned B C e Repair Replace etc in accordance with this form or D of part III below e Return to Customer Part I Please complete the following information for single unit or multiple unit returns Address No office use only Address No office use only Bill to Ship to Purchase Order Contact Name Phone Fax E Mail Part Il Please complete Parts II amp III for each unit returned Model No Part No Description Range Calibration S N Reason for return L Failure LL Upgrade O Verify Operation L Other 1 Describe the conditions of the failure Frequency Intermittent Physical Damage Environmental Conditions Communication CPU watchdog etc Attach a separate sheet if necessary 2 Comm interface used Standalone RS 485 Ethernet Modem PLM 2W or 4W or SNW Other 3 What is the Firmware revision What is the Software amp version Part III If checking replaced for any question below check an alternate option if replacement is not available A If product is within the warranty time period but is excluded due to BBI s warranty clause would you like the product C repaired returned replaced scrapped B If p
20. rectly Bristol Babcock s world headquarters are located at 1100 Buckingham Street Watertown Connecticut 06795 U S A Our main phone numbers are 860 945 2200 860 945 2213 FAX Regular office hours are Monday through Friday 8 00AM to 4 30PM Eastern Time excluding holidays and scheduled factory shutdowns During other hours callers may leave messages using Bristol s voice mail system Telephone Support Technical Questions During regular business hours Bristol Babcock s Application Support Group can provide telephone support for your technical questions For technical questions about TeleFlow products call 860 945 8604 For technical questions about ControlWave call 860 945 2244 or 860 945 2286 For technical questions regarding Bristol s OpenEnterprise product call 860 945 2501 or e mail openenterprise bristolbabcock com For technical questions regarding ACCOL products Open BSI Utilities as well as Bristol s Enterprise Server Enterprise Workstation products call 860 945 2286 For technical questions about Network 3000 hardware call 860 945 2502 You can e mail the Application Support Group at bsupport bristolbabcock com The Application Support Group also maintains a service area within our main web site Technical information as well as software updates are available in this area To access our web site go to bristolbabcock com services techsupport For assistance in interfacing Brist
21. roduct were found to exceed the warranty period would you like the product LJrepaired returned replaced LJ scrapped C If product is deemed not repairable would you like your product C returned replaced scrapped D If BBI is unable to verify the discrepancy would you like the product C returned L replaced see below Continue investigating by contacting the customer to learn more about the problem experienced The person to contact that has the most knowledge of the problem is phone If we are unable to contact this person the backup person is phone Special Requests Ship prepaid to Bristol Babcock Inc Repair Dept 1100 Buckingham Street Watertown CT 06795 Phone 860 945 2442 Fax 860 945 3875 Form GBU 13 01 Rev A Bristol Babcock Training GET THE MOST FROM YOUR BRISTOL BABCOCK INSTRUMENT OR SYSTEM e Avoid Delays and problems in getting your system on line e Minimize installation start up and maintenance costs Make the most effective use of our hardware and software e Know your system Transducer to Manifold Dielectric Isolation Kit Multivariable Transducer Dielectric Gasket amp Flange Seals 2 Valve Block Manifold Top Washers 4 Dielectric Bolt Sleeves 4 Bottom Washers 4 Mounting Bolts 4 As you know a well trained staff is essential to your operation Bristol Babcock offers a full schedule of classes conducted b
22. t ira sete tal soles oe i a 4 f e 3 ae h Real time Switch eai ume WHCN FIVE PORT SWITCH FIVE PORT WITH FIBER SWITCH This LED will be on solid when proper power has been applied to the unit ACT LNK The activity ACT and link LNK indication is combined into one LED on the Industrial Ethernet LEDs Switches There is one of these LEDs per port OFF This would indicate that there is not a proper Ethernet connection Link between the port and another Ethernet device Make sure the proper cable type is in use and that it has been plugged securely into the ports at both ends See section 5 for proper Ethernet cabling ON Solid not flashing This would indicate that there is a proper Ethernet connection Link between the port and another Ethernet device but no communications activity is detected Flashing This would indicate that there is a proper Ethernet connection Link between the port and another Ethernet device and that there is communications activity 10 100 This LED indicates what speed of communications is detected on the port There is one of these LEDs LEDs per RJ45 port The fiber optic port does not have one of these LEDs because its speed is fixed at 100 Mbps OFF A 10 Mbps 10BaseT connection is detected ON A 100 Mbps 100BaseTx connection is detected Mbps Megabits per Second Switch User Manual Page 4 of 13 Section 3 Installation Overview The Industrial Ethern
23. t location transportation prepaid within thirty 80 days of the sending of such notification and which upon examination by Bristol proves to be defective in material and workmanship Bristol is not responsible for any costs of removal dismantling or reinstallation of allegedly defective or defective goods If a Buyer does not wish to ship the product back to Bristol the Buyer can arrange to have a Bristol service person come to the site The Service person s transportation time and expenses will be for the account of the Buyer However labor for warranty work during normal working hours is not chargeable Under no circumstances will Bristol be liable for incidental or consequential damages resulting from breach of any agreement relating to items included in this quotation from use of the information herein or from the purchase or use by Buyer its employees or other parties of goods sold under said agreement How to return material for Repair or Exchange Before a product can be returned to Bristol Babcock for repair upgrade exchange or to verify proper operation form GBU 138 01 must be completed in order to obtain a RA Return Authorization number and thus ensure an optimal lead time Completing the form is very important since the information permits the Bristol Babcock Repair Dept to effectively and efficiently process the repair order You can easily obtain a RA number by A FAX Completing the form GBU 13 01 and faxing it to
24. th MAC addresses Address learning Address aging Address migration Backoff operation Back pressure Broadcast storm protection Buffering Illegal frames Late collisions Dropped after 512 bit times Environmental Required supply voltage 10 30 VDC Power consumption 1 9 W Sport 3 2 W 5 port fiber Power saving Max screw 5 port switch 3 48 in lbs 0 4 Nm terminal torque 4 1 fiber port switch 5 3 in lbs 0 6 Nm Max wire gauge Operating temp range Storage temp range Humidity Flammability Electrical safety EMI emissions EMC immunity Surge withstand Vibration Hazardous locations Dimensions Mounting a Switch User Manual Page 12 of 13 Section 8 Service Information Product Support Switch User Manual Service Information Refer to the following sections of this manual when troubleshooting communication problems associated with a ControlWave Industrial Ethernet Real time Switch Section 2 LED Indicators Section 4 Power Wiring Section 5 Ethernet Wiring During regular business hours Bristol Babcock s Application Support Group can provide telephone support for your technical questions For technical assistance in troubleshooting a ControlWave Industrial Ethernet Real time Switch call 860 945 2244 or 860 945 2286 You can e mail the Application Support Group at bsupport bristolbabcock com The Application Support Group also maintains a service area within our main web site Technic
25. trial Ethernet Switch requires no supervisory processor to operate properly Flow control The Industrial Ethernet Switch automatically supports flow control frames on both the transmit and receive sides Forwarding The Industrial Ethernet Switch supports store and forward mode It will forward messages with known addresses out only the appropriate port Messages with unknown addresses broadcast messages and multicast messages will get forwarded out all ports except the source port The Industrial Ethernet Switch will not forward error packets 802 3x pause frames or local packets Full Half duplex operation The RJ45 ports of the Industrial Ethernet Switch automatically support auto sense both full and half duplex flow control The fiber optic port has a slide switch which allows you to select the desired operation Illegal frames Illegal frames as defined by IEEE 802 3 will be dropped This includes short frames long frames and FCS error frames IEEE 802 3 compliant The Industrial Ethernet Switch strictly abides to the IEEE 802 3 standard for 10BaseT and 100BaseTX Ethernet communications Late collision If a packet experiences collisions after 512 bit times of transmission the packet will be dropped Plug and play This means that most functions or features of the Industrial Ethernet Switch are automatic and that there are minimal or no optional parameters that need to be set Just plug in your Ethernet cables apply powe
26. y full time professional instructors Classes are offered throughout the year at four locations Houston Birmingham Orlando and our Watertown CT headquarters By participating in our training your personnel can learn how to install calibrate configure program and maintain any and all Bristol Babcock products and realize the full potential of your system For information or to enroll in any class contact our training department in Watertown at 860 945 2269 For Houston classes you can also contact our Houston office at 713 685 6200 A Few Words About Bristol Babcock For over 100 years Bristol has been providing innovative solutions for the measurement and control industry Our product lines range from simple analog chart recorders to sophisticated digital remote process controllers and flow computers all the way to turnkey SCADA systems Over the years we have become a leading supplier to the electronic gas measurement water purification and wastewater treatment industries On off shore oil platforms on natural gas pipelines and maybe even at your local water company there are Bristol Babcock instruments controllers and systems running year in and year out to provide accurate and timely data to our customers Getting Additional Information In addition to the information contained in this manual you may receive additional assis tance 1n using this product from the following sources Contacting Bristol Babcock Di
Download Pdf Manuals
Related Search