Falcon 350 Dry Well Bain Marie User Instructions for E350/42 model
Contents
1. insulating sleeving covers capillary tube Neatly coil excess length over a suitable object of approximately 50mm diameter Ensure that earth bonding terminal is re fitted underneath thermostat fixing lug 3 2 2 Dry Heat Models a Remove control panel See Section 3 1 2 b Remove any containers etc c Remove thermostat phial from fixing clips d Pull off thermostat connections noting locations e Pull off thermostat knob and remove two fixing screws f From inside controls compartment undo gland nut which secures capillary tube to boss Push phial downward into compartment and remove thermostat g When refitting ensure that insulating sleeving is fitted to capillary tube Neatly coil excess length over a suitable round object of approximately 50mm diameter Ensure that earth bonding terminal is re fitted below thermostat fixing lug 3 3 PILOT LAMPS To Remove All Models a Remove control panel See Section 3 1 b Pull off lamp connections c Undo nut that secures lamp at rear to remove Fit replacement in reverse order 3 4 HEATING ELEMENTS To Remove 3 4 1 Wet Heat Models a Remove control panel See Section 3 1 1 b Remove water well etc See Section 3 2 1 c From inside of controls compartment remove element connections d Remove fixings that secure element and remove it e When replacing element ensure that earth bonding wires are reconnected to element flanges using shak2. E350 40 and E350 41 WET HEAT BAINS MARIE 350 42 E350 43 DRY HEAT BAINS MARIE INSTALLATION and SERVICING INSTRUCTIONS IMPORTANT The installer must ensure that the installation of the appliance is in conformity with these instructions and National Regulations in force at the time of installation Particular attention MUST be paid to BS7671 IEE Wiring Regulations Electricity at Work Regulations Health And Safety At Work Act Fire Precautions Act This appliance has been CE marked on the basis of compliance with the Low Voltage and EMC Directives for the voltages stated on the Data Plate WARNING THIS APPLIANCE MUST BE EARTHED On completion of the installation these instructions should be left with the Engineer in Charge for reference during servicing Further to this The Users Instructions should be handed over to the User having had a demonstration of the operation and cleaning of the appliance IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE INSTALLING AND COMMISSIONING THIS APPLIANCE FAILURE TO COMPLY WITH THE SPECIFIED PROCEDURES MAY RESULT IN DAMAGE OR THE NEED FOR A SERVICE CALL PREVENTATIVE MAINTENANCE CONTRACT In order to obtain maximum performance from this unit we would recommend that a Maintenance Contract be arranged with SERVICELINE Visits may then be made at agreed intervals to carry out adjustments and repairs A quotation will be given upon request to the contact numbers below WE
3. EE Directive Registration No WEE DC0059TT PRO At end of unit life dispose of appliance and any replacement parts in a safe manner via a licenced waste handler Units are designed to be dismantled easily and recycling of all material is encouraged whenever practicable Falcon Foodservice Equipment T100666 Ref 2 HEAD OFFICE AND WORKS Wallace View Hillfoots Road Stirling FK9 5PY Scotland SERVICE CONTACT PHONE 01438 363 000 FAX 01438 369 900 Warranty Policy Shortlist Warranty does not cover Correcting faults caused by incorrect installation of a product Where an engineer cannot gain access to a site or a product Repeat commission visits Replacement of any parts where damage has been caused by misuse Engineer waiting time will be chargeable Routine maintenance and cleaning Gas conversions i e Natural to Propane gas Descaling of water products and cleaning of water sensors where softeners conditioners are not fitted or are fitted and not maintained Blocked drains Independent steam generation systems Gas water and electrical supply external to unit Light bulbs Re installing vacuum in kettle jackets Replacement of grill burner ceramics when damage has been clearly caused by misuse Where an engineer finds no fault with a product that has been reported faulty Re setting or adjustment of thermostats when unit is operating to specification Cleaning and unblocking of fryer filter sys
4. eproof washers below nuts 3 4 2 Dry Heat Models a Remove control panel See Section 3 1 2 b Remove all containers supporting components and perforated spreader panel which covers element c Remove element connections from inside controls compartment d Undo fixings that secure element and remove it Replace all parts in reverse order Take care to refit serrated washers below element fixing nuts Reposition spreader plate with large holes facing toward rear E350 40 WET BAIN MARIE and E350 42 DRY BAIN MARIE WIRING DIAGRAM Drawing No AW32477 B TERMINAL BOX EARTH A 7 8 1 7 5 2 8 N EN H 2 9 a THERMOSTAT RED NEON AMBER NEON E350 41 WET BAIN MARIE and E350 43 DRY BAIN MARIE WIRING DIAGRAM Drawing No AW32476 B ELEMENT ELEMENT TERMINAL BOX EARTH L N 5 10 5 9 6 3 gt 2 10 SS 11 2 THERMOSTAT AMBER NEON
5. er thermostat opens 9 After satisfactory completion of installation demonstrate method of operation to kitchen staff Point out location of isolating switch for use in an emergency or during routine cleaning SECTION 3 SERVICING BEFORE ATTEMPTING ANY MAINTENANCE SWITCH OFF AT THE MAINS ISOLATING SWITCH AND TAKE STEPS TO ENSURE THAT IT IS NOT INADVERTENTLY SWITCHED ON When ordering spares please quote model number serial number and voltage as stamped on data plate at rear of appliance 3 1 CONTROL PANEL To Remove 3 1 1 Wet Heat Models a Remove two screws in upper flange of panel i e below front hob overhang b Ease panel forward at top then lift it slightly to release lower locations c Move panel forward 3 1 2 Dry Heat Models a Remove drip tray located below control panel b Remove two screws in upper flange of control panel c Allow panel to drop down slightly to release lower fixings and remove panel 3 2 THERMOSTAT To Remove 3 2 1 Wet Heat Models a Remove control panel See Section 3 1 1 b Remove well complete with containers etc by grasping handles and lifting vertically c Remove thermostat phial from fixing clips d Pull off thermostat connections noting locations e Pull off knob and remove two screws f From inside controls compartment undo gland nut which secures thermostat tube to boss Push phial down into comparment and remove thermostat g Upon re fitting ensure
6. ll at this stage and switch on unit to check that elements thermostat and pilot lamps are functioning correctly The RED neon is lit when power is available i e isolating switch is closed The AMBER neon is lit when elements are ON it will go out whenever thermostat opens h After satisfactory completion of installation demonstrate the method of operation to kitchen staff and point out location of isolating switch for use in an emergency or during routine cleaning etc 2 2 E350 42 and E350 43 Dry Bains Marie a Position unit and carefully level it using feet adjusters on a counter or table If it is to be installed upon a stand please refer to instructions supplied with stand b The appliance is supplied complete and ready to connect to mains supply c To gain access to terminals proceed as follows Lift out container supports at top of unit and also perforated spreader plate which covers element Remove drip shield which covers terminal box at rear of appliance Remove terminal box cover d Terminal block is now accessible and supply cables can be connected After connections have been made replace components noting that large holes in spreader plate must face toward rear f Switch unit ON Check that elements are heating and that pilot lamps are functioning The RED neon is lit when power is available i e isolating switch is closed The AMBER neon is lit when elements are ON and will go out whenev
7. o mains electric supply must be made through a suitable isolating switch with a contact separation of at least 3mm in all poles Wiring should conform to regulations and the installation should satisfy local supply authority Warning THESE APPLIANCES MUST BE EARTHED A suitable terminal is provided for this purpose and must be used Note Precautions regarding earth leakage must be taken during installation 1 5 ELECTRICAL RATINGS Electrical ratings are as stated on appliance data plate 1 6 CONTROLS All models are controlled by a single thermostat SECTION 2 ASSEMBLY 2 1 E350 40 and E350 41 Wet Bains Marie a Remove feet from bag and screw into locations on unit base prior to positioning b Place unit in position and carefully level it using feet adjusters if it is to be mounted on a counter or table If it is to be installed a stand please refer to instructions supplied with accessory c The appliance is supplied complete and ready to be connected to supply mains d To gain access to terminals the front facia panel has to be removed Remove two fixings in upper flange of panel below overhanging hob Ease top of panel forward then lift it upward to release lower fixings e Terminal block is now accessible and supply cables can be fed to it through inbuilt conduit tube f After connecting unit replace facia panel and ensure that bottom location is properly assembled g Do not install water we
8. tems due to customer misuse Lubrication and adjustment of door catches Cleaning and Maintenance Cleaning of burner jets Poor combustion caused by lack of cleaning Lubrication of moving parts Lubrication of gas cocks Cleaning adjustment of pilots Correction of gas pressure to appliance Renewing of electric cable ends Replacement of fuses Corrosion caused by use of chemical cleaners SECTION 1 INSTALLATION UNLESS OTHERWISE STATED PARTS WHICH HAVE BEEN PROTECTED BY THE MANUFACTURER ARE NOT TO BE ADJUSTED BY THE INSTALLER 1 1 MODEL NUMBER NETT WEIGHTS and DIMENSIONS WIDTH DEPTH HEIGHT WEIGHT WEIGHT MODEL ibe E350 40 305 20 44 E350 41 305 33 73 E350 42 305 18 39 E350 43 700 650 305 30 67 All Weights are nett exclusive of containers 1 2 SITING The unit should be installed on a table or similar surface Alternatively it may be installed upon the purpose designed floor stand supplied by Falcon If it is to be positioned in close proximity to a wall partition etc a clearance of 25mm at the rear and sides should be observed A vertical clearance of 600mm between the top of the appliance and any overlying combustible surface must also be provided 1 3 ELECTRICAL SUPPLY These appliance are for use on single phase AC supplies only 1 4 SUPPLY CONNECTION The cable entry is located at rear of appliance and is suitable for 20mm conduit The connection t
Download Pdf Manuals
Related Search