HD41 Quick Installation Guide
Contents
1. Sync System Internal S N Ratio 50 dB AGC Off Weight On Auto Electronic Shutter 1 60 1 100 000 sec Al AES Selection Switchable White Balance ATW 1 800 K 10 500 K AWC Manual BLC Low Mid High Off HBLC HSBLC Gamma 0 20 1 00 adjustable Sense Up Auto x2 x1024 D WDR Off On selectable level Privacy Mask 8 mask zones configurable Motion Detection 4 motion detection zones configurable Mirror Off On horizontal mirror selectable 3DNR Auto Motion Off Low Mid High selectable Lens Type 2 8 mm to 12 0 mm Vari focal Auto Iris F1 4 Lens Iris Control Direct Drive DC Vari focal Auto Iris Lens Angle of View Lens Horizontal 96 7 wide to 24 1 tele Vertical 71 2 wide to 18 2 tele Electrical Specifications Input Voltage 12 VDC 10 Power Consumption 4 0 W max Mechanical Dimensions L x H x W 5 12 x 4 02 x 5 12 130 0 mm x 102 0 mm x 130 0 mm Weight 0 66 Ibs 0 3 Kg Net 0 99 Ibs 0 45 Kg Shipping Construction Housing ABS Dome Polycarbonate Environmental Temperature Operating 14 F to 122 F 10 C to 50 C Storage 4 F to 140 F 20 C to 60 C Relative Humidity 0 to 95 non condensing Regulatory Emissions FCC Part 15B Class A Immunity EN501302. www honeywellvideo com 1 800 796 CCTV North America only HVSsupport honeywell com Document 800 11941 Rev C 06 2012 Line up the triangle V and the red LOCK mark to secure the base to the dome 2012 Honeywell International Inc All rights reserved No part of this publication may be reproduced by any means without written permission from Honeywell The information in this publication is believed to be accurate in all respects However Honeywell cannot assume responsibility for any consequences resulting from the use thereof The information contained herein is subject to change without notice Revisions or new editions to this publication may be issued to incorporate such changes focus lever locations When the camera is correctly positioned zoomed and focused push the shroud back together with the lens Note When you push the shroud back together with the lens this will change the tilt angle that you have set for the lens adjustment labelled B When the shroud and lens are snapped back together tilt both pieces back to the desired lens position 8 Specifications Video Signal Specifications Video Standard NTSC Scanning System 525 lines 2 1 Interlace Image Sensor 1 3 CCD Number of Pixels H x V 768 x 494 Minimum Illumination 0 3 lux F1 4 AGC on 50 IRE Horizontal Resolution 620 TVL Video Output 1 0 Vp p composite 75 Ohms
3. 2 VDC power supply Use an appropriate low voltage power cable to prevent fire or electrical shock Please ensure that your installation area can support the weight of the camera Operating Conditions Avoid aiming the camera towards an extreme light source for example light fixtures to prevent damaging the CCD Do not view direct sunlight with the camera This camera is rated for indoor operation do not expose this camera to rain or moisture Avoid operating or storing the unit in the following locations Extremely humid dusty hot cold environments extreme temperature conditions where the operating temperature is outside the recommended range of 14 F to 122 F 10 C to 50 C Be especially careful to provide ventilation when operating under high temperatures Close to sources of powerful radio or TV transmitters Near a cooling or heating device Close to fluorescent lamps or objects reflecting light Under unstable light sources may cause flickering Package Includes One Camera One Quick Install Guide this document One Configuration Manual Local video monitor output and power Mounting screws x2 cable Cable Connections aas ie VIDEO yellow Power Video Signal BNC Y Sm i i j WA a POWER red Power Z Video GND DC 12V POWER VIDEO 800 11941 C 06 2012 2 HD41 Performance Series Indoor High Resolution Dome Camera Camera Installation 6 Came
4. 4 www honeywellvideo com
5. Honeywell __ Performance Series High Resolution Indoor Fixed Mini Dome Camera HD41 Quick Installation Guide Key Features 1 3 CCD Image sensor e Day and Night capability SDN or electronic 5th Generation DSP chip 0 3 lux minimum illumination Sense Up DSS DC Auto Iris Vari Focal lens 2 8 mm 12 mm High Speed Shutter 620 TV lines Horizontal Resolution High Resolution images No Noise or Ghosting effect with DNR 800 11941 C 06 2012 Safety Instructions BEFORE OPERATING OR INSTALLING THE UNIT READ AND FOLLOW ALL INSTRUCTIONS AFTER INSTALLATION retain the safety and operating instructions for future reference 1 HEED WARNINGS Adhere to all warnings on the unit and in the operating instructions INSTALLATION Install in accordance with the manufacturer s instructions Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty Do not install the unit in an extremely hot or humid location or in a place subject to dust or mechanical vibration The unit is not designed to be waterproof Exposure to rain or water may damage the unit Any wall or ceiling mounting of the product should follow the manufacturer s instructions and use a mounting kit approved or recommended by the manufacturer POWER SOURCES This product should be operated only from the type of power source indicate
6. arts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards THIS SYMBOL INDICATES THAT CAUTION DANGEROUS VOLTAGE RISK OF ELECTRIC CONSTITUTING A RISK OF SHOCK ELECTRIC SHOCK IS PRESENT DO NOT OPEN WITHIN THE UNIT NO USER SERVICEABLE PARTS INSIDE IMPORTANT eee eee REFER SERVICING TO QUALIFIED SERVICE MAINTENANCE INSTRUCTIONS CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER THIS SYMBOL INDICATES THAT PERSONNEL A ACCOMPANY THIS UNIT FCC Compliance Statement Information to the user This equipment has been tested and found to comply with the limits for a Class A digital device Pursuant to part 15 of the FCC Rules these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CAUTION Changes or modifications not expressly approved by the party responsible for compliance could voi
7. d on the marking label If you are not sure of the type of power supplied to your facility consult your product dealer or local power company WARNING This device is configured for 12 VDC operation only do NOT connect to higher voltage Use only with NRTL approved 12 VDC power supplies To prevent potential ground loop issues a separate PSU should be used for each camera A multiple output PSU may be used if the multiple output PSU has isolated and protected 2A MAX outputs HEAT Situate away from items that produce heat or are heat sources such as radiators heat registers stoves or other products including amplifiers WATER MOISTURE This is an indoor rated camera Do not use this unit near water or in an unprotected outdoor installation or any area classified as a wet location MOUNTING SYSTEM Use only with a mounting system recommended by the manufacturer or sold with the product ATTACHMENTS Do not use attachments not recommended by the product manufacturer as they may result in the risk of fire electric shock or injury to persons ACCESSORIES Only use accessories specified by the manufacturer CLEANING Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel REPLACEMENT PARTS When replacement p
8. d the user s authority to operate the equipment Canadian Compliance Statement This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la Classe A est conforme la norme NMB 003 du Canada Warranty and Service Subject to the terms and conditions listed on the Product warranty during the warranty period Honeywell will repair or replace at its sole option free of charge any defective product returned prepaid In the event you have a problem with any Honeywell product please call Customer Service at 1 800 796 CCTV North America only for assistance or to request a Return Merchandise Authorization RMA number Be sure to have the model number serial number and the nature of the problem available for the technical service representative Prior authorization must be obtained for all returns exchanges or credits Items shipped to Honeywell without a clearly identified Return Merchandise Authorization RMA number may be refused 2 Precautions Precautions for Use Read and keep these instructions This camera should be installed by qualified personnel only There are no user serviceable parts inside Do not disassemble this camera other than to make initial adjustments Do not touch the camera lens dome or bezel front glass plate Do not drop the camera or subject it to physical shock Do not use a strong or abrasive detergent when cleaning the camera Use a UL approved regulated 1
9. deo connector screws as you make the adjustments You can pan the entire camera board and gimbal to the monitor you will use 360 labelled A in graphic above Tilt the camera lens up and down 90 labelled while setting up the B and or rotate the lens 360 C SNIS la Use the three points of adjustment A B and C to Focus i Zoom H Ng f adjustment P MW pS adjustment The video output position the camera connector on the correctly camera board is located next to the OSD menu controls that you can use to make Use the two levers located on the lens to adjust zoom and focus as needed see the image for zoom and configuration changes While monitoring the camera picture on the monitor adjust the camera position orientation zoom and focus settings as described in the Camera Positioning Zoom and Focus Adjustment section Using the connected monitor make camera configuration changes through the OSD menus see the Configuration Guide included with your camera for more information Re install the dome cover to the housing base as described in the Securing the Dome Cover section 7 Securing the Dome Cover Snap the dome cover back into the housing base by lining up the triangle V on the cover with the red LOCK mark on the housing base Line up the triangle V and the red LOCK label and snap the dome cover and base together to secure the camera 2nd video output connector Honeywell
10. ra Positioning Zoom and Focus Adjustment Remove the dome from the 1 With the dome removed you can see that the lens is surrounded by a protective housing base by inserting a shroud see the image below So or flathead Mounting Use two hands to draw back the shroud from the lens by placing both thumbs on the screwdriver into the slot surface upper front section of the shroud with your fingers bracing the back side of the lens and twisting and pushing your thumbs towards your fingers see the image below Connect the yellow video output connector to the video input port on your monitor DVR Connect the red power connector to your 12 VDC power source Feed the cables into the hole in the mounting Video and oe power cable surface such as a ceiling i see the Cable see graphic Connections Install the housing base diagram onto the mounting surface AON using the two mounting Vp Yi RER W J and lens screws provided IESE SEA Housing N A i h Place fingers behind Connect the local video base X NINNA the lens to brace it die e output cable to the video gaa 2nd video whom pushing Dak back shroud V7 the shroud output connector on the Sh output camera board located QR AERA fe eee behind the lens and 3 Position the camera lens and gimbal so that the camera is viewing the required video gimbal Connect the other Mounting scene Use the connected monitor to check that the field of view is oriented correctly end of the vi
Download Pdf Manuals
Related Search