Sheep Auto Drafter User Manual
Contents
1. SHEEP AUTO DRAFTER Instructions ENG PUBLISHED BY Gallagher Group Limited Kahikatea Drive Private Bag 3026 Hamilton New Zealand www gallagherams com Copyright Gallagher Group Limited 2007 All rights reserved Patents Pending Sheep Auto Drafter User Manual 3E2374 Edition 5 0 October 2012 DISCLAIMER While every effort has been made to ensure accuracy neither Gallagher Group Limited nor any employee of the company shall be liable on any ground whatsoever to any party in respect of decisions or actions they may make as a result of using this information In accordance with the Gallagher policy of continuing development design and specifications are subject to change without notice Developed and manufactured by Gallagher Group Limited an ISO 9001 2000 Certifed Supplier 3E2374 Sheep Auto Drafter User Manual Table of Contents IER OCU CUION eosscsesetistdeauabasccesuceandeenaden a E ANEA REONE a RAEE E Eaa 5 What is the Sheep Auto Drafter cc cccccccssssccccsssscecceecceseensceeeeaeecesseneseeseeaeeeesenaesessees 5 Benefits of using the Sheep Auto Drafter ceeccccssssccccseseeeeceesececeeeecceseeseceeseaeecessageses 8 SCCM APIO STO US Cis masa in ce anata ao ta nat Vahvaa au tend ee Gage eared Laka saksan 9 Setting UD TOK SUCCESS melmaesi ammal tetyis tsis et avitti a a isl ve kussa 10 Positioning the Sheep Auto Drafter c ccsssccsssessecsessscessessssccesessscnesessens2. 150mm away from the Sheep Auto Drafter and insert the air lines through the conduit at the top of the sorting unit Figure 8 Inserting air lines Slot the sorting unit onto the spigots protruding upwards from the Sheep Auto Drafter foot Screw them together with Tek screws 14 gauge 75mm Tool required 3 8in socket Figure 9 Attaching to Sheep Auto Drafter Attach the male and female connections on the end of the air lines to their mates inside the roof of the sorting unit Check the air lines are not sagging as they may get caught when the doors operate a Figure 10 Attaching air lines 3E2374 Sheep Auto Drafter User Manual Note It is very important that there is nothing touching the Sheep Auto Drafter when it is weighing animals as this may affect its accuracy This includes the sorting unit so make sure you attach it correctly Using the Remote Control The buttons to manually control the sorting unit are situated at the top of the remote control see Figure 11 They will allow you to direct animals to the left straight ahead or right through the first sorting unit attached to the Sheep Auto Drafter For more about using the remote control see Using the Remote Control p 22 Drafting buttons Figure 11 The sorting unit remote control buttons Using an extra sorting unit It is possible to attach an extra sorting unit to the Sheep Auto Drafter to allow up to 5 different sorting directions s
3. 2 The transfer of information between the different components connected to the Sheep Auto Drafter Page 7 3E2374 Sheep Auto Drafter User Manual Benefits of using the Sheep Auto Drafter The benefits you will receive from using the Sheep Auto Drafter include the following Page 8 Save time and labour One person can operate the Sheep Auto Drafter using a remote control This means that you will still be in control of its operation while at a distance Additionally as you control the gates by using the remote control the physical demands of operating gates particularly drafting gates is removed Improve work efficiency Increase the speed of a variety of stock management tasks and also drafting throughput as the process can be automated This means stock and people spend less time in the yards Decrease the incidence of injuries for stock and handlers The Sheep Auto Drafter is made from composite materials The chances of injury from collisions or general usage are significantly lower as composite is far more forgiving and there are no sharp or protruding edges Additionally the flooring has been designed to provide safe footing so slipping does not occur All of the moving parts e g rams are protected by guards ensuring there are no trapping points Additionally they are substantially lighter than traditional systems making them much easier to shift Quiet operation The innovative composite construction of the Sheep Au
4. 900cm wide by 2600cm length should be laid to fit the Sheep Auto Drafter and a single sorting unit They should be bolted to it using the mounting holes provided see Figure 3 It is recommended that 4 M10 x 125mm masonry anchors with 10mm x 25mm flat washers and a masonry drill bit size of 10mm are used to attach the Sheep Auto Drafter and sorting unit A permanent mounting also allows for the optimisation of surrounding yards and races to efficiently feed stock into the weighing and drafting set up Power and compressed air requirements Both power and compressed air are necessary to operate the Sheep Auto Drafter and sorting unit An air supply is needed to operate the unit entry and exit gates and also the drafting gates Power requirements Page 10 The Sheep Auto Drafter is powered by an external 230V to 12V DC adaptor This comes as part of the package when you buy the Sheep Auto Drafter and can be connected to your AC power supply input range 100 240V AC You can also run the Sheep Auto Drafter off a 12V DC battery e g a car battery where there is no conventional power supply If you have a scale indicator or a RFID reader attached to the Sheep Auto Drafter they will need to be powered separately by their own batteries as no power supply runs to them from the unit 3E2374 Sheep Auto Drafter User Manual Note If you are wanting to read EIDs then make sure you keep the power supply 1m or more away from the unit
5. NEW ZEALAND E Floods fires or acts of God Gallagher Animal Management Systems 181 Kahikatea Drive m Use of an arc welder on loadbars or equipment or Private Bag 3026 Hamilton 3240 steelwork attached to loadbars while a WeighScale is connected SOUTH AFRICA Gallagher their Distributors and their Dealers accept Rudd Products no responsibility for the misuse of this product Bush Willows 24 Begonia Road Kyalami Agricultural Holdings Gallagher their Distributors and their Dealers accept Kyalami Johannesburg Gauteng 1684 no responsibility for any accident caused subseguently to any tampering with or modification to or for the USA CANADA misuse of this product Gallagher North America 130 W 23rd Avenue Gallagher their Distributors and their Dealers accept no liability for conseguences and or secondary damages or losses of any kind sustained directly or PLEASE READ INSTRUCTIONS CAREFULLY BEFORE USE PLEASE COMPLETE DETAILS AND KEEP WITH YOUR RECEIPT IT IS YOUR PROOF OF WARRANTY North Kansas City MO 64116 Missouri
6. SPECIFICATIONS General AC Input Voltage 100 240V DC Input Voltage 11 5 15V Environmental Protection IP55 Rating Operating Temperature 152 to 602 C Dimensions Packaged Footprint Length 1850 mm 2438mm Width 820mm 790mm Height 1550 mm Weight Crate Assembly 125kg Draft module 44kg Footprint 457 mm 881 mm 1100 mm 790 mm 660 mm 1450 mm 794 mm 2438 mm Figure 20 Sheep Auto Drafter and sorting unit dimensions Page 47 3E2374 Sheep Auto Drafter User Manual Page 48 3E2374 Sheep Auto Drafter User Manual INDEX A Actions to avoid e 41 Adjusting the Sheep Auto Drafter width 30 Assembling the Sheep Auto Drafter e 15 ASSEMBLING THE SHEEP AUTO DRAFTER AND SORTING UNIT e 15 Assembling the sorting unit e 15 Automatic Release Mode e 32 Automatic use e 19 B Benefits of using the Sheep Auto Drafter 8 Button functions e 22 C CARE AND MAINTENANCE e 40 Cleaning instructions 40 Connecting the sorting unit to the Sheep Auto Drafter 18 20 D Dimensions e 47 G General e 47 H How it is powered e 24 How the sorting unit works e 19 How to turn the Sheep Auto Drafter on e 15 If the red fault LED is on 43 INTRODUCTION e 5 Issue checklist and possible solutions 43 M Manual Release Mode 35 Manual use e 19 Method e 20 Moving the Sheep Auto Drafter 13 p Parts replacement 41 Positioning the Sheep Auto Drafter e 10 Potential issues not ident
7. Sheep Auto Drafter operation It is likely that you will use the E Stop button very rarely as it is intended for use in emergency situations only It is the large red button situated at the front of the Control Bridge see Figure 18 E Stop Figure 18 E Stop button position To use the E Stop button 1 Inan emergency hit the E Stop button situated on the Control Bridge The red E Stop LED will start to flash The air pressure will be removed this will allow you to manually open the entry or exit gates if you need to 2 Resolve the issue that has occurred 3 Release the E Stop button The white mode LED will start to flash 4 Press either the Retain Release or the Start button e on the remote control or the Entry Gate button on the Control Bridge only Pressing Start on the remote or pressing the Entry Gate button on the Control Bridge will put the unit into Automatic Release Mode Page 37 3E2374 Sheep Auto Drafter User Manual Pressing Retain Release will put it into Manual Release Mode The unit will continue operations from the point it was halted e g if you were weighing animals and an animal had just been captured then after restarting it would weigh the animal and release it Using without weighing no scale attached Occasionally you may wish to use the Sheep Auto Drafter without the scale indicator attached e g if you are just wanting to record animals EIDs The
8. Sheep Auto Drafter can still operate without the scale indicator To set up the Sheep Auto Drafter without the scale indicator 1 Connect the loop back cable into the socket on the Control Bridge instead of the scale indicator so that the load cells are not connected see Figure 19 Figure 19 Attaching the loop back cable Page 38 3E2374 Sheep Auto Drafter User Manual TURNING THE SHEEP AUTO DRAFTER OFF At the end of each session you will want to turn the Sheep Auto Drafter off To turn the Sheep Auto Drafter off 1 Press and hold the Power button situated on the Control Bridge see Figure 18 down for a couple of seconds Notes The exit gate will open the entry gate will shut and the sorting unit gates will move to the sides if not there already Note If you have the E Stop button pressed then the gates will stay in their current positions If you are in Automatic Release Mode the Sheep Auto Drafter will attempt to process any sheep in the unit before it switches off e g if it is a weighing session and there is a sheep in the unit it will be weighed and released This process however will be affected by where in the process the unit is when you press the power button e g if you press it before the scale indicator has had a chance to make a drafting decision then the animal will be released out the centre of the sorting unit Finally the air supply to the gates will be switched off and the LED lam
9. To override an automatic release decision and keep an animal in the unit To release an animal which has been retained To stop the unit operation and open the entry gate e g if you want to remove a sheep when two have got into the unit or to let outa sheep which is jammed in the gate To shut the unit entry gate Page 23 3E2374 Sheep Auto Drafter User Manual For scenarios which include more about using the remote control refer to Using the Sheep Auto Drafter p 32 How it is powered Page 24 The remote control requires 2 alkaline AAA batteries to run do not use rechargeable batteries Note If the batteries in the remote run out while the Sheep Auto Drafter is operating in Automatic Release Mode then the unit will continue operating until it runs out of sheep or you press the E Stop button If they run out while it is running in Manual Release Mode then it will complete the last action you requested it to do then it will stop For more about Automatic and Manual Release Mode see the Using the Sheep Auto Drafter p 32 3E2374 Sheep Auto Drafter User Manual PURPOSE AND FUNCTION OF CONTROL BRIDGE LAMPS LEDS AND BUTTONS Lamps The Control Bridge houses a number of different lamps both on top and around the front above the entry gate see Figure 14 These are intended to give you an indication of the Sheep Auto Drafter s operational status i e if it is ready to operate operating normally o
10. direction Once the drafting gate has shifted into position the exit gate will open and the animal will be released Once the animal has been released the entry gate will open and the next animal will be captured From here you can continue in manual mode by pressing Retain Release button oR hold the next animal in the unit until you have set the drafting gates Page 35 3E2374 Sheep Auto Drafter User Manual To clear multiple animals from the Sheep Auto Drafter Occasionally multiple animals may enter the unit at the same time In this scenario you will want to remove the extra animal s 1 Press the Entry Gate button on the remote control D or press the Entry Gate button on the Control Bridge This will open the entry gate The white LED mode lamp will begin to flash 2 Remove the extra animal s 3 Press the Start KH or Retain Release EA button on the remote control to close the gate and restart the unit operation or press the Entry Gate button on the Control Bridge Pressing Start on the remote or the Entry Gate button on the Control Bridge will put the unit into Automatic Release Mode Pressing Retain Release will put it into Manual Release Mode If the issue occurs during a weighing session there are two possible additional factors to consider a Have you pressed the Entry Gate button before the scales have locked in a weight b Have you pressed the Entry Gate button after the scales
11. for the construction and use of surrounding yards and races adapted from Behavioral Principles of Livestock Handling by Temple Grandin Race construction leading up to the Sheep Auto Drafter Sides Layout Width Materials Sheep have a wide visual field The width is affected by the amount of wool they have on their head and ranges from 191 to 306 degrees Any handling races including the race leading up to the Sheep Auto Drafter should have solid side walls to prevent animals from seeing distractions outside the race Any moving objects e g people flapping objects or a coat hung on a race fence seen through the sides of a race can cause balking or frighten sheep Solid side walls are especially important if animals are unaccustomed to the facility Curved single file races are recommended for moving sheep up to the Sheep Auto Drafter A curved race is more efficient for two reasons Firstly it prevents the animal from seeing what is at the other end of the race until it is almost there Secondly it takes advantage of the natural tendency of sheep to circle around a handler moving along the inner radius of the race Ideally the race will be designed in a way that organises sheep into single file by the time they reach the junction with the Sheep Auto Drafter This helps to ensure that only one sheep enters the Sheep Auto Drafter at a time and makes stock flow smoother As sheep can be of varying sizes e g adult sheep and
12. have locked in a weight If option a occurs then you don t need to take any further action However if option b occurs it is a good idea to remove the false weight reading from the scale indicator before you continue to find out how to do this refer to your scale user manual Using the Stop button to pause Sheep Auto Drafter operation Occasionally you may want to briefly stop the Sheep Auto Drafter so that you can carry out another task e g answer a phone call or shift some sheep which are out of range of the Sheep Auto Drafter To stop the Sheep Auto Drafter Page 36 1 Press the red Stop button O on the remote control Theentry gate will close and the exit gate will open The white LED mode lamp will begin to flash Note If you were operating in Automatic Release Mode any operation the unit was carrying out will be completed before an animal is released e g if 3E2374 Sheep Auto Drafter User Manual the unit was weighing an animal the weight will be locked into the scale indicator before the exit gate is opened 2 Tostart operations again press either the Retain Release A the Start button O on the remote control or press the Entry Gate button on the Control Bridge Pressing Start on the remote or pressing the Entry Gate button on the Control Bridge will put the unit into Automatic Release Mode Pressing Retain Release will put it into Manual Release Mode Using the E Stop button to halt
13. indicator attached to the Sheep Auto Drafter Drafting can also be controlled manually by the operator An extra sorting unit can be linked end to end to enable up to 5 way drafting The Sheep Auto Drafter and sorting unit have both been constructed from composite materials They are lightweight making them easy to transport and set up extremely durable and because of the forgiving nature of composite they are safe for you and your stock When the Sheep Auto Drafter is combined with the sorting unit you can carry out a range of activities including automatic Electronic ID EID reading weighing and drafting The Sheep Auto Drafter can be operated from a distance using a remote control Page 5 Page 6 3E2374 Sheep Auto Drafter User Manual The different parts of the Sheep Auto Drafter are shown in the diagram below A Sheep Auto Drafter G power button B sorting unit H E stop button C drafting gate I Entry Gate button D pressure gauge J Control Bridge E RFID reader K entry gate F scale indicator Figure 1 The different components of the Sheep Auto Drafter 3E2374 Sheep Auto Drafter User Manual Figure 2 shows how data is transferred between the different equipment attached to the Sheep Auto Drafter ESI RFID KN ear Indicator Input EN gt Control Box Gate gt f Control k 1 lt Draft Commands NA Antenna pe J cells Load a Figure
14. open Once a sheep has entered the entry gate will close to capture it When the EID has been successfully read the exit gate will open and the sheep will be released To read EIDs and draft by list not weighing 1 Connect the loop back cable into the socket on the Control Bridge instead of the scale indicator so that the load cells are not connected To find out how to do this see Using without a scale attached p 38 Make sure the RFID reader is connected Set up the scale indicator to read EIDs and select a draft list Fan Press the green Start button SP on the remote control or press the Entry Gate button on the Control Bridge for 2 seconds or more The white LED mode lamps will now be on to indicate that you are in Automatic Release Mode Theentry gate will open Once a sheep has entered the entry gate will close to capture it When the EID has been successfully read the exit gate will open and the sheep will be drafted according to the conditions set up in the scale indicator Page 33 3E2374 Sheep Auto Drafter User Manual To read EIDs weigh and draft by weight 1 2 Set up the scale indicator so it is ready to weigh animals automatically and specify the weight limits for each group Make sure the RFID reader is also attached Press the green Start button SY on the remote control or press the Entry Gate button on the Control Bridge for 2 seconds or more The white LED mode lamps w
15. the bottom of the panel will allow you to resize the unit for different sized animals so that they are restricted from turning around and adjusting them at the top will allow more room for handler access to stock These slots will allow you to resize the unit from 300 525mm wide 3E2374 Sheep Auto Drafter User Manual To adjust the Sheep Auto Drafter width 1 Lift the side panel of the unit upwards and drop it into the appropriate slot One side the one which is most accessible to the operator has locking levers These levers are designed to allow the top to be extended further out for greater operator access They can be dropped outwards or inwards into the neighbouring slot to ensure the panel is locked into position Figure 17 Slots and locking lever to allow Sheep Auto Drafter width adjustment Page 31 3E2374 Sheep Auto Drafter User Manual USING THE SHEEP AUTO DRAFTER The Sheep Auto Drafter can be run in two different modes Automatic Release Mode or Manual Release Mode The one you select will depend on whether you want it to run independently or not In either case if there are no animals in the unit the Sheep Auto Drafter will automatically allow animals in However if it is in Manual Release Mode you will be in control of when they are released and the direction the sorting unit will release them in whereas in Automatic Release Mode the settings you enter into the scale indicator will determine how the unit and sortin
16. Drafter User Manual Scale not operating not communicating Check the scale indicator is switched on Check the RS232 cable is securely attached between the Sheep Auto Drafter and the scale indicator Check the scale indicator communication settings are correct Check you have the correct port set up in the scale indicator for the connection between the scales and unit refer to the appropriate user manual Remote control not working due to PCB issue Replace the PCB a rare fault Contact your Gallagher representative for advice on how to repair this issue Solenoid short on the 12V rail Contact your Gallagher representative for advice on how to repair this issue Short on the 5V loopback rail Check for dirt or water in the indicator cable or loopback connector if they are clean and dry and the fault persists contact your Gallagher representative for advice on how to repair this issue Unit is unable to identify the cause of the fault Contact your Gallagher representative for advice on how to repair this issue Potential issues not identified by fault flash sequences Sheep Auto Drafter not operating Page 44 Is the green power LED on If no then check there is a functional power supply connected Is the white mode LED flashing see cause below Is the red E Stop LED flashing see cause below Is the air connected and at sufficiently high pressure Check the pressure gauge to see if there is enough pressu
17. ation e g to remove an animal if two have accidentally entered the unit Using two remote controls In the situation where you are using two remote controls you need to consider which one is currently paired up with the unit The remote control that you use first during a session will be synchronised with the unit This means any other remote controls will not operate To find out how a remote control is synchronised see To turn the Sheep Auto Drafter on p 28 Figure 13 Remote control button layout Page 22 3E2374 Sheep Auto Drafter User Manual Automatic Release Mode no user interaction Button Button name Action KA Start Sheep Auto Drafter operation Stop the Sheep Auto Drafter operations Manual Release Mode user controls animal exit orange Select drafting O direction Straight ahead O Retain Hold an animal in the Release unit or release an orange 5 animal from the unit D Entry Gate Open and close the orange entry gate Table 1 Remote control button function Reasons for use At the start of a session After stopping the unit by using the Stop button the Gate button or the E Stop button To switch to Automatic Release Mode from Manual Release Mode To pause unit operation if you want to go and briefly do something else e g answer the phone move sheep When an animal is in the unit to set the drafting direction and then open the exit gate to release the animal
18. button is depressed The procedure to turn the Sheep Auto Drafter on is slightly different if the E stop button is depressed however it is not expected that this will be a regular occurrence 1 Press the Power button which is situated on the Control Bridge see Figure 16 The green power light should come on if it doesn t refer to Troubleshooting p 42 for ideas on how to resolve the problem The white LED mode lamp will now start flashing to indicate that the unit is ready to communicate with the remote control 2 Ifthe E Stop button is depressed the red E Stop LED will start flashing You need to release the E Stop button before you can continue with the start up Once it is released the E Stop lamp will switch off 3 Restart the Sheep Auto Drafter by either Using the Remote n Press the green Start button D on the remote control to synchronise it with the Sheep Auto Drafter The unit will start to operate in Automatic Release Mode Or From the Control Bridge Press the Entry Gate button to resume operations For more about this and how to use the Auto Drafter see Using the Sheep Auto Drafter p 32 For more about the use of the E Stop button see Using the E Stop button to halt Sheep Auto Drafter operation p 37 Adjusting the Sheep Auto Drafter width Page 30 Both of the Sheep Auto Drafter side panels can be adjusted to a variety of positions by using the four slots provided on either side Adjusting them at
19. cucescecceccucence 28 How to turn the Sheep Auto Drafter ON ooooooiooio ona aan a aan annan eaa a aa aaaaan 28 Adjusting the Sheep Auto Drafter Width ooussoo nona aan ana ana n naan aan aeaeen 30 Using the SNEED AUTO DraFteksssmmasossmsssessaaakssstasaksa asa osa Pahaa a Kea Saa EERE ALUN 32 Automatic Release Moaormmusmauksaintsvuueuetovatskukam akatuvts e TE R 32 Manual Release MOU Girona n E setin eamohdukidiiua saaaam it idtaitma hstsimm 35 Using the Stop button to pause Sheep Auto Drafter operation ssessseseserreesressrresreee 36 Using the E Stop button to halt Sheep Auto Drafter operation oosoon niini 37 Using without weighing no scale attached ssssnesssseennsssserressssreressssreresserreeesserresese 38 Turning the Sheep Auto Drafter OTT smiusasvasa asiassa muIseveky ao so Nama Kaa KIA osk oak Saas apmka ak vonean 39 To turn the Sheep Auto Drafter Off cccccccccccssssececeeeececeeneceeeeeeeesseneceeseeneeessuaeeeessees 39 Careand maintenant E aoira eni e vet n v isk kam EEN 40 CIE AMINE INSIKUCTIONS rero A a a avi 40 Parts replacememntumsummassoastun a aaa a a A 41 PICTIONS TO AVOIG ceine EEE r AEO ET 41 TTOUDIESIIOOTIMG oraaa e E EE N 42 To use the LED Tault flash SEQUENCE noen AA 42 Issue checklist and possible solutions uu suusso oonan annan a aan eaa a anna aaaaana 43 Page iil 3E2374 Sheep Auto Drafter User Manual SPOcITICATION S creien ca
20. e considered The compressor providing air for the Sheep Auto Drafter is best located at a distance to reduce noise levels Rubber stops on gates in the yards around the Sheep Auto Drafter will help reduce noise The effects of pain or fright Research indicates that sheep can remember a painful or frightening experience for many months Sheep which had been inverted in a sheep handling machine were more difficult to move through the machine the following year The fact that the Sheep Auto Drafter has been designed with the comfort and safety of stock in mind will help to ensure animals experience of them is positive This will aid in the smooth entry and flow of stock through the system on future occasions It is also worthwhile keeping in mind that livestock which have had gentle handling in the past will be less stressed when they are handled in the future Think about how your actions will affect your future interactions with stock and the efficiency of the operations you wish to carry out Moving the Sheep Auto Drafter 1 Hutson As the Sheep Auto Drafter is very light 100 kg due to its construction from composite materials it can be lifted manually by two people Note Make sure you have the side panels attached when you shift the Sheep Auto Drafter and that they are on the inside slot Also close the gates at either end G D 1980 The effect of previous experience on sheep movement through yards Applied Animal E
21. ee Figure 12 To control the sorting direction you will need to set up appropriate weight limits or a sorting list in the scale indicator nS a a aa ANIMALFLOW X1 SX T Ty A NAA S Sheep Auto Drafter sorting units Figure 12 Using an extra sorting unit Page 21 3E2374 Sheep Auto Drafter User Manual USING THE REMOTE CONTROL The Sheep Auto Drafter comes with a remote control The remote control can be operated from within a 15m radius of the unit which allows you to carry out tasks at a distance while still maintaining control of the unit operations Button functions The unit can operate in two modes Automatic Release Mode and Manual Release Mode The seven buttons on the remote are used to operate the Sheep Auto Drafter and sorting unit in these two modes see Figure 13 The bottom two green and red buttons are used to operate the unit in Automatic Release Mode In this mode the unit will automatically release animals without user intervention by using conditions set up in the scale indicator prior to the session Additionally the Entry Gate button 0 can be used in Automatic Release Mode to control the gate if sheep need to be cleared from the unit This function is also available on the Sheep Auto Drafter Control Bridge see Figure 14 The top five orange buttons are used to operate the unit in Manual Release Mode In this mode you can control how an animal exits the unit or interrupt the unit oper
22. eration There is a short in a solenoid or the cabling The unit will not operate Contact your Gallagher representative for advice on how to repair this issue No drafting decision made e Has the scale indicator been set up correctly for drafting e Have either drafting by weight or drafting by list instructions been set up in your scale indicator e Is the RS232 cable securely attached between the scale indicator and the Sheep Auto Drafter e Is the RS232 cable attached to the correct port on the scale indicator Multiple sheep in Sheep Auto Drafter See To clear multiple animals from the unit p 36 for instructions on how to deal with this Page 45 3E2374 Sheep Auto Drafter User Manual EID failure to read Is it a one off failure an occasional failure sporadic or a continuous failure If it is then a one off failure Does the animal have a tag an occasional failure Are there a lot of metal objects e g yard fences or gates close to the Sheep Auto Drafter Metal particularly if it is rubbing other metal objects can set up an electrical interference which impedes the antennae s ability to identify EIDs Is it just animals with a tag in a particular ear i e right or left that are not being read If this is the case one of the antennae may not be working a continuous failure Is the RFID reader attached to the Sheep Auto Drafter antennae Page 46 3E2374 Sheep Auto Drafter User Manual
23. essssecesesrsenees 10 Power and compressed air requirements cssecccceseccceeseeceeaesceeeeeececseeeeeesauaeesseees 10 Scales and RFID reader requirements c sscccccsssecccceeseccceeseceeeeesecessuaeecesseneseesaaneeeees 11 Recommendations for the construction and use of surrounding yards and races 12 Moving the Sheep Auto Drafter rsimion a A ENAA 13 Assembling the Sheep Auto Drafter and sorting unit ccscsccsccsccsccscecceccsccscecceccescces 15 Assembling the Sheep Auto Drafter aruuicoicocir en aO TE EO 15 ASSCIMDIING the SOMME UIC cesna a E r tel em s 15 USING the sorntine Unit siciraindicciasiriaicceccneutindeveidetanenleasacindenerieesdnevatsh N T 19 HOW thesorUne UNIEWONRKS issnin a E A AA 19 Connecting the sorting unit to the Sheep Auto Drafter eseesseseseseessrrrssrrrerresrrerserreeeee 20 WISIN t16 Remote COontrolammessa assistant Mavacidaieatossapepetinidintans Prauasteedtees 21 SIE alt CX Ua SONO JOTI ie erni re EO aenionemen viens 21 Using the Remote CONE Ol isi cccdotssstiaseteavonidatacsKesstiadsieestassnadsadescensntmenumcsdotseniaaterteseuiarsedeenens 22 BUON TURCEIONSmssstat osaks emes kamkolmmesiek leamea ekaks auetuku sumseapsust 22 FOWItIS POWereld ummessa vaasa aika is E T A 24 Purpose and function of Control Bridge Lamps LEDs and Buttons sccsccsccsscescesees 25 Turning the Sheep Auto Drafter ON ccsccscssccccscceccsccsceccecceccnccsceccnccscesceccec
24. fter ensure that you have the following correctly attached Page 28 power compressed air scales if weighing animals To attach scales Attach the scale indicator to the scales mount on the top of the Control Bridge Attach the loop back cable which connects the unit and the scale indicator This will end in an amphenol socket at the scales end Figure 15 The loop back cable Attach the RS232 cable comms cable which connects the unit electronics to Port 1 on the scale indicator This cable will transmit the drafting decision data from the scale indicator to the unit so that the drafting gates can be set up If weighing animals with EID attach the RS232 cable between the scale and the RFID reader Note If you do not wish to weigh animals you need to attach the loop back cable into the socket on the Control Bridge instead of the scale indicator so the Sheep Auto Drafter can still operate RFID reader if animals have EID To attach RFID reader Attach the RFID reader to the reader mount on the top of the Control Bridge Connect the antenna cable to the RFID reader 3E2374 Sheep Auto Drafter User Manual If weighing or drafting animals too connect the RS232 cable between the reader and the scale Note If you are not using the Sheep Auto Drafter to read EIDs e g if it is turned off or you are just using it to manage untagged animals keep the caps on the sockets where the an
25. g unit will operate Automatic Release Mode It is likely that you will use the unit most frequently in this mode When the Sheep Auto Drafter is operating in Automatic Release Mode the white mode LED lamps around the front will be on The following are some ways you can use the Sheep Auto Drafter and sorting unit while in Automatic Release Mode e Weighing animals and releasing e Weighing animals and drafting using weight conditions specified in your scale indicator draft by weight e Reading EIDs e Reading EIDs and drafting using conditions specified in your scale indicator draft by list e Reading EIDs weighing and drafting using conditions specified in your scale indicator draft by weight or list Follow the instructions below to carry out each of the scenarios mentioned above Note For instructions on how to set up and use your scale and or RFID reader you will need to refer to the appropriate user manual To weigh and release animals Page 32 1 Setup the scale indicator so it is ready to weigh animals automatically 2 Press the green Start button J on the remote control or press the Entry Gate button on the Control Bridge for 2 seconds or more The white LED mode lamps will now be on to indicate that you are in Automatic Release Mode The entry gate will open Once a sheep has entered the entry gate will close to capture it When the sheep has been successfully weighed the scale indicator wil
26. ial from around the gates under the floor and between the Sheep Auto Drafter and sorting unit Notes Page 40 It is acceptable to clean the unit down with a water blaster but do NOT spray up under the bridge area or around the two scale head reader towers with a high pressure blast that could drive water into the bridge Take care that you do not drive water into the loadcell assemblies by directing a high pressure jet on this area you would need to have the sheep auto drafter on its side to pose this risk Washing the unit down at a car wash station where you apply soapy water etc under control of the operator is acceptable as long as the above notes are taken into account when rinsing the unit down When towing on a trailer there MUST be a cover over the sheep auto drafter to prevent rain driving into the bridge area where the main circuit board is 3E2374 Sheep Auto Drafter User Manual Parts replacement The following parts can be replaced e load cells e circuit board inside Control Bridge e aircontrolvalves e air cylinders e lower gate dampers Contact your Gallagher representative to find out where to get the parts and how to install them Actions to avoid Generally speaking the Sheep Auto Drafter will withstand most of the conditions and chemicals typically encountered in the farming environment however avoiding the following is essential e using the Control Bridge to lift the unit e g by inse
27. ified by fault flash sequences e 44 Power and compressed air requirements 10 Purpose and function of control bridge lamps LEDs and buttons e 25 R Race construction leading up to the Sheep Auto Drafter 12 Recommendations for the construction and use of surrounding yards and races e 12 S Scales and RFID reader requirements e 11 Scenarios for use 9 Setting up for success e 10 Specifications 47 T To adjust the Sheep Auto Drafter width e 31 To clear multiple animals from the Sheep Auto Drafter 36 45 To hold an animal in the Sheep Auto Drafter 35 To manually set the drafting direction 35 To read ElDs e 33 To read EIDs and draft by list not weighing 33 To read EIDs weigh and draft by list 34 To read EIDs weigh and draft by weight 34 To set up the Sheep Auto Drafter without the scale indicator 38 To stop the Sheep Auto Drafter 36 To turn the Sheep Auto Drafter off 39 To turn the Sheep Auto Drafter on 29 To turn the Sheep Auto Drafter on if the E Stop button is depressed e 30 To use the E Stop button 37 To use the LED fault flash sequence e 42 To weigh and draft animals draft by weight 33 To weigh and release animals 32 Troubleshooting 25 26 29 30 Troubleshooting 42 U Using an extra sorting unit e 21 Using the E Stop button to halt Sheep Auto Drafter operation e 37 Using the Remote Control e 21 Page 49 3E2374 Sheep Auto Drafter U
28. ill now be on to indicate that you are in Automatic Release Mode Theentry gate will open Once a sheep has entered the entry gate will close to capture it When the EID has been read and the sheep has been successfully weighed the scale indicator will beep The scale indicator will display both the animal s weight and the direction it will be drafted in The exit gate will open and the sheep will be drafted according to the weight limits set up in the scale indicator To read EIDs weigh and draft by list Page 34 i 2 Make sure the RFID reader is connected Set up the scale indicator so it is ready to weigh animals automatically and to read EIDs Then select a draft list Press the green Start button S on the remote control or press the Entry Gate button on the Control Bridge for 2 seconds or more The white LED mode lamps will now be on to indicate that you are in Automatic Release Mode The entry gate will open Once a sheep has entered the entry gate will close to capture it When the EID has been read and the sheep has been successfully weighed the scale indicator will beep The scale indicator will display both the animal s weight and the direction it will be drafted in The exit gate will open and the sheep will be drafted according to the conditions set up in the scale indicator 3E2374 Sheep Auto Drafter User Manual Manual Release Mode Use this mode when you would like to run the unit yourself The en
29. l beep the exit gate will open and the sheep will be released 3E2374 Sheep Auto Drafter User Manual To weigh and draft animals draft by weight 1 Set up the scale indicator so it is ready to weigh animals automatically and specify the weight limits for each group Press the green Start button D on the remote control or press the Entry Gate button on the Control Bridge for 2 seconds or more The white LED mode lamps will now be on to indicate that you are in Automatic Release Mode The entry gate will open When a sheep has entered the entry gate will close to capture it Once the sheep has been successfully weighed the scale indicator will beep The scale indicator will display both the animal s weight and the direction it will be drafted in The exit gate will open and the sheep will be drafted according to the conditions set up in the scale indicator To read EIDs 1 Connect the loop back cable into the socket on the Control Bridge instead of the scale indicator so that the load cells are not connected To find out how to do this see Using without a scale attached p 38 Set up the scale indicator to read EIDs Make sure the RFID reader is also attached Press the green Start button S on the remote control or press the Entry Gate button on the Control Bridge for 2 seconds or more The white LED mode lamps will now be on to indicate that you are in Automatic Release Mode The entry gate will
30. lambs it is useful to have a race with adjustable sides in the final lead up the last 180cm However if the race width is fixed approximately 50 cm is the recommended width This is the same dimension as the internal edge of the Sheep Auto Drafter entry gate surround The materials the surrounding races are made of have the potential to affect the reliability of the RFID reader Metal components are best avoided if possible particularly if they rub together as this can cause interference in the signal between the reader and the EID Vision and lighting Page 12 Where the Sheep Auto Drafter is positioned illumination should be uniform and diffuse much like a bright cloudy day Shadows and bright spots should be minimised Sheep have a tendency to move from dim areas to brighter areas provided the light is not glaring in their eyes Situate the Sheep Auto Drafter to take advantage of natural light Skylights combined with other natural lighting can even out 3E2374 Sheep Auto Drafter User Manual Noise light levels so consider installing translucent polycarbonate roofing and or walls if the area is dark In facilities where livestock are handled loud or novel noises should be avoided because they distress livestock The sound of metal clashing together can cause balking and agitation As the Sheep Auto Drafter is constructed of composite materials its operation is very quiet but the noise level in the surrounding yards should b
31. on from this button only Sheep Auto Drafter in a fault state see Troubleshooting p 42 for diagnosis E Stop button depressed 3E2374 Sheep Auto Drafter User Manual Buttons The Entry Gate button on the Control Bridge of the Sheep Auto Drafter has more functionality than the same button on the remote control If the Entry Gate button on the Control Bridge is used to override the entry gate then only the Entry Gate button on the Control Bridge can resume normal operation The table below shows the abilities of the Entry Gate button when pressed on the Control Bridge Button Button Action name Entry Gate Open and close the entry gate Start the Sheep Auto Drafter in Automatic Release Mode Reasons fo use To stop the unit operation and open the entry gate e g if you want to remove a sheep when two have got into the unit or to let out a sheep which is jammed in the gate To shut the unit entry gate To enter stop mode ie entry closed exit open The unit has been powered on and the remote is not available The Entry Gate button on Control Bridge remote control or STOP button was used to override the entry gate A fault condition has been corrected Table 3 Function of Entry Gate button on Control Bridge Page 27 3E2374 Sheep Auto Drafter User Manual TURNING THE SHEEP AUTO DRAFTER ON How to turn the Sheep Auto Drafter on Before starting the Sheep Auto Dra
32. ors by attaching lock nuts and washers m10 nut 10mm flat washer to the end of each one Tool required 17mm combination spanner To find out how to attach the sorter to the Auto Drafter see Connecting the sorting unit to the Sheep Auto Drafter p 20 under Using the Sorting Unit on page 35 later in this manual Adding an extra sorting unit Page 18 An extra sorting unit can be attached to the first end to end using 2 zinc plated hex bolts M6 x 75mm long and flat washers 6mm x 22mm long Note When weighing animals it is very important that there is nothing touching the Sheep Auto Drafter as this may affect its accuracy Take care that the sorter is attached correctly and any lead up races are not touching the Auto Drafter 3E2374 Sheep Auto Drafter User Manual USING THE SORTING UNIT The sorting unit allows you to automatically separate animals into groups by e weight using weight limits set up in the scale indicator e reading ElDs and using drafting lists set up in the scale indicator Alternatively you can control the sorting unit manually with the remote control If you purchase one sorting unit then animals can be divided into three different groups however you do have the option of linking an extra sorting unit This will give you the ability to draft in up to five different directions Like the Sheep Auto Drafter the sorting unit is constructed primarily from composite materials and has pneumatically opera
33. ps will turn off e If you want to stop all power use e g if you are using a battery to power the unit and you want to save power then you will need to disconnect the power cable as well or switch the power source off e itis agood idea to make sure the caps are on the sockets where the antennae cables emerge from the side panels at the RFID reader end when the Sheep Auto Drafter is not in use This will prevent dirt and moisture from getting into the sockets Page 39 3E2374 Sheep Auto Drafter User Manual CARE AND MAINTENANCE The Sheep Auto Drafter is of robust design so that it can withstand typical farming conditions as a result it is resilient in most situations However following the instructions below will help you to get the best results from your unit and to avoid damaging it Cleaning instructions It is inevitable that dung and other dirt will be tracked through the unit during routine use It is best to clear the build up of these materials from some key areas regularly so that the unit will operate effectively Under the floor A build up of material may touch the floor and affect the unit s weighing accuracy Around the gate area Material gathering here may hamper gate movement Between the Sheep Auto Drafter and the sorting unit A build up here may touch the floor and affect the unit s weighing accuracy To clean the unit Remove the side panels Sweep or wash the floor Scrape out any build up of mater
34. r has a fault Power E Stop Fault lamps ode lamps Figure 14 Position of Sheep Auto Drafter Control Bridge lamps and buttons Table 2 describes the purpose of each lamp Refer to the Troubleshooting p 42 section for the specifics of how LEDs indicate particular problems LED LED LED state colour position Flashing Green Beside Sheep Auto Power supply low Sheep Auto Drafter power power Drafter switched on button on switched off Control No power Bridge supply Too much power Page 25 Page 26 i colour LED position Wrapped mode around front of Control Bridge Red Wrapped fault around front of Control Bridge Red Beside E E Stop Stop button on Control Bridge LED state Sheep Auto Drafter switched off E Stop button depressed Sheep Auto Drafter switched off Sheep Auto Drafter operating normally Sheep Auto Drafter switched off Sheep Auto Drafter operating normally Table 2 Function of LED lamps 3E2374 Sheep Auto Drafter User Manual Flashing Single flash Double flash Sheep Auto Drafter Sheep Auto is in Automatic Drafter in stand Release Mode by and ready for operation waiting for communication from the remote or Entry Gate button on the Control Bridge Sheep Auto Drafter has been overridden by the Entry Gate button on the Control Bridge waiting for communicati
35. re pressure should be in the green zone on the pressure gauge Are the red fault LEDs flashing If yes then there is an issue that you need to resolve before the unit will begin to work again To find out how to activate the fault flash sequence see the instructions above 3E2374 Sheep Auto Drafter User Manual Green power LED flashing The power supply is low Although the Sheep Auto Drafter can continue to operate it may be worthwhile checking your power supply White mode LED flashing Single flash The Sheep Auto Dre is in standby and ready to operate Press the Start KH or Retain Release button on the remote control to continue or press the Entry Gate button on the Control Bridge for 2 seconds or more Double flash The Sheep Auto Drafter has been stopped using the Entry Gate button on the Control Bridge Press the Entry Gate button on the Control Bridge to resume operation Red E Stop LED flashing The E Stop button is depressed d Release it and then press either the Start Sj or Retain Release button on the remote control to continue or press the Entry Gate button on the Control Bridge for 2 seconds or more Remote control won t work or the auto sorting unit is not responding to the remote control e Are the batteries flat Try changing them e Is the remote control damaged e Was the Entry Gate button on the Control Bridge pressed to release an animal This button must be pressed again to resume op
36. ror In addition accurate weighing and drafting ensures that all stock fall into the correct groups to ensure they achieve premium prices at sale Scenarios for use The flexible nature of the Sheep Auto Drafter allows you to carry out many activities simply and easily These include Automatically e Weighing animals and releasing them or drafting them using the weight groupings you have set up in your scales e Reading EIDs and weighing animals then drafting using the weight groupings you have set up in your scales draft by weight e Reading EIDs then drafting using a set of conditions you have set up in your scales draft by list the range of options will be dependent on the brand and model of the attached weighing indicator Manually e Controlling the movements of animals out of the Sheep Auto Drafter yourself e Overriding an automatic setting to retain an animal in the unit so that you can examine it for some reason or draft it in a different direction from the automatic setting e Temporarily pause an automatic operation so that you can resolve issues for example if two animals become caught in the Sheep Auto Drafter Page 9 3E2374 Sheep Auto Drafter User Manual SETTING UP FOR SUCCESS Positioning the Sheep Auto Drafter It is recommended for best performance that the Sheep Auto Drafter is mounted ona hard level flat surface Ideally particularly for permanent installations a concrete pad of approximately
37. rting fork lift prongs under the Control Bridge e Resting objects on top of the Control Bridge Page 41 3E2374 Sheep Auto Drafter User Manual TROUBLESHOOTING There are a number of steps you can take when the Sheep Auto Drafter is not operating correctly to identify and resolve the issue L General LED check The first thing to do when you encounter an issue is to check the LED lamps on the Control Bridge They may give you an indication of where the issue is Table 2 lists the LEDs and what their different states indicate Check all cables are attached firmly and working Check your power and air cables are attached and working The green power LED should be on The pressure gauge should register air pressure in the green zone Check the cables between the unit the scales and the RFID reader are all attached correctly Activate flash fault sequence If the unit has identified it has a fault the multiple red LED lamps on the front of the Control Bridge will start to flash For some faults you can activate a flash sequence which will help you to identify which area the issue is in Find out how to activate the fault flash sequence below Go through issue checklist The issue checklist below may also give you some ideas on how to resolve the fault To use the LED fault flash sequence Page 42 1 If a fault is not immediately obvious activate the LED fault flash sequence by briefly pressing the Power b
38. ser Manual Using the remote control e 22 Using the Sheep Auto Drafter 19 24 29 30 Using the sorting unit 19 Using the Stop button to pause Sheep Auto Drafter operation 36 Using two remote controls e 22 Using without weighing no scale attached 33 38 W What is the Sheep Auto Drafter e 5 Page 50 ONE YEAR WARRANTY REGISTER ONLINE AT www gallagherams com TO EXTEND YOUR WARRANTY TO TWO YEARS FOR THIS PRODUCT FROM DATE OF PURCHASE SELLING DEALER STAMP This product is guaranteed free from defects in material indirectly a result of failure or defect in any product or workmanship for a period of one year from date of material installation or service purchase by the end user Gallagher will repair or replace at their option any faulty product returned to them or their Dealer within this time period Freight forwarding costs incurred by the Customer in the warranty process remain the responsibility of the AUSTRALIA Gallagher Australia Pty Ltd 14 Somerton Park Drive Campbellfield Melbourne Victoria 3061 Customer EUROPE This warranty does not cover damage including Gallagher Europe Bv subsequent corrosive damage due to Hekkum 9 9774 TH Adorp Gn 7 Unauthorised repairs Netherlands N Modifications IRELAND Failure to follow care and maintenance guidelines Gallagher Power Fence Systems IRL described in the User Manual Kinsale Road n Physical Mishandling Cork a Lightning Strike
39. side panels to avoid interference with the RFID reader antennae Compressed air requirements Once the compressor is connected and running you will be able to see what the pressure is at the unit by looking at the pressure gauge attached to the Control Bridge see Figure 4 It should read between 4 6bar in the green zone Ensure it does not enter the red zone gt 6bar A reading above 6bar indicates a regulator issue which would need investigation Readings below 4bar are likely to be caused by an air supply compressor problem A typical compressor would be a 2HP 24 litre tank single phase machine Figure 4 Pressure gauge on the Control Bridge Scales and RFID reader requirements The Sheep Auto Drafter has been specifically designed to operate with the Gallagher SmartTSi SmartScale 800 Weigh Scale 810 and Weigh Scale 610 scales Please note Drafting by list is not available on the Weigh Scale 610 scale It will also operate with some other brands of weighing indicators your dealer will know which are compatible RFID radio frequency identification antennae are installed in each of the unit side panels A SmartReader BR or R unit is needed to communicate with the antennae The antennae will recognise EID which are either HDX half duplex or FDX full duplex and those which are inserted as implants or boluses however these are less commonly used Page 11 3E2374 Sheep Auto Drafter User Manual Recommendations
40. t LED is on 1 flash Sheep or other object jammed in the Sheep Auto Drafter gates When something becomes jammed in the gates the gates will continue attempting to close for a period of time If they do not succeed then the Sheep Auto Drafter will go into the fault state You need to clear the gate and then either press the Start S button or Retain Release buttons on the remote control or the Entry Gate button on the Control Bridge before the unit will begin to operate again Note You can also release jammed animals prior to the Sheep Auto Drafter going into a fault state by pressing the Gate button 0 while the gate is still trying to close This will open the gate so the animal is released or can be pushed out The Sheep Auto Drafter or sorting unit gates won t operate Check your compressed air supply e Does the air pressure gauge have a reading in the green zone 4 6bar e ls the compressor on and working e Arethe air lines undamaged and connected correctly Faulty solenoid sensor or ram e If one of these is faulty it will need replacing 2 flashes No power to load cells e Check the scale indicator is attached and switched on or e Make sure the loopback cable is correctly connected 3 flashes Fault in the loopback cable connection e Check that you have the loopback cable correctly attached Page 43 4 flashes 5 flashes 6 flashes 7 flashes 10 flashes 3E2374 Sheep Auto
41. ted gates which means it is light safe to use and very quiet How the sorting unit works You can run the sorting unit automatically which is probably how you will use it most of the time or you can run it manually using the remote control You cannot use it independently from the Sheep Auto Drafter as the Sheep Auto Drafter electronics control the sorting unit operation Automatic use If the sorting unit is working automatically its operation is controlled by the scale indicator which sends signals through the Sheep Auto Drafter electronics to the sorting unit You will need to set up weight limits or a drafting list using EIDs in the scale indicator to direct the sorting unit To find out how to do this refer to your scales user manual If you have attached an extra sorting unit then you will need to run it automatically as the remote control can only be used to operate one sorting unit Manual use If the sorting unit is under manual control the commands from the remote are transmitted through the Sheep Auto Drafter electronics to the sorting unit You will need to use the remote to make each drafting decision For more detailed scenarios covering particular uses of the sorting unit in combination with the Sheep Auto Drafter see Using the Sheep Auto Drafter p 32 Page 19 3E2374 Sheep Auto Drafter User Manual Connecting the sorting unit to the Sheep Auto Drafter Method L Page 20 Sit the sorting unit about
42. tennae cables emerge This will prevent dirt and moisture from getting into the sockets To turn the Sheep Auto Drafter on The Sheep Auto Drafter can be started in Automatic mode either with or without the remote The following instructions are used if the E Stop button is not depressed 1 Press the Power button which is situated on the Control Bridge see Figure 16 The green power light should come on if it doesn t refer to Troubleshooting p 42 for ideas on how to resolve the problem The white LED mode lamp will start flashing to indicate that the unit is ready to communicate with the remote control Start the Sheep Auto Drafter by either Using the Remote Press the green Start button D on the remote control to synchronise it with the Sheep Auto Drafter The unit will start to operate in Automatic Release Mode Or From the Control Bridge Press the Entry Gate button on the Control Bridge for 2 seconds or more The unit will start to operate in Automatic Release Mode For more about Automatic Release Mode and how to use the Auto Drafter see Using the Sheep Auto Drafter p 32 Note If the Entry Gate button is pressed for less than 2 seconds it will remain in standby mode awaiting pairing with the remote control or further instruction from the Control Bridge Figure 16 The Sheep Auto Drafter Power button Page 29 3E2374 Sheep Auto Drafter User Manual To turn the Sheep Auto Drafter on if the E Stop
43. terer itera seas eae eae ae 47 EE er fee ence AE ted aE N E Se aE eo Maa ee ES NE eS RT eT ON ROOT A OnE Sone ME aT 47 IMI ASI ONS E E E EATEN E E OAEI AAE AETA EEE ANE release onsen A EE 47 MOEK aa A T AT OA Aa 49 Page iv 3E2374 Sheep Auto Drafter User Manual INTRODUCTION Welcome to the Sheep Auto Drafter user manual In it you will find instructions on using the Sheep Auto Drafter and drafting unit as well as hints to help you resolve any problems you encounter In designing the Sheep Auto Drafter Gallagher have continued their tradition of creating products which are functional practical easy to use innovative and in tune with the needs of the rural market The use of a ruggedized composite as the main construction material is a breakthrough innovation in stock handling equipment design which comes with a wide range of benefits What is the Sheep Auto Drafter The Sheep Auto Drafter is a sheep handling unit containing an integrated weighing platform which will connect with a variety of brands of electronic scales Pneumatically operated gates at either end of the auto drafter allow stock in and out These can either be controlled automatically by setting up some conditions in the scales or manually by the stock handler Each side panel contains antennae to allow reading of Electronic ID EID The sorting unit links with the Sheep Auto Drafter to automatically draft stock The conditions for drafting are set up in the scale
44. thology 6 1233 Page 13 Page 14 3E2374 Sheep Auto Drafter User Manual Transport poles can be purchased from your local Gallagher distributor which can be inserted into slots provided in the gate surrounds see Figure 5 Once the poles have been inserted the Sheep Auto Drafter can be lifted and repositioned see Figure 6 pole insertion holes Figure 5 Holes for insertion of transport poles Figure 6 Lifting using the transport poles Alternatively the Sheep Auto Drafter can be lifted mechanically e g by forklift by inserting forks or strops under the floor or by attaching strops to the four corners of the transport poles nearest the end supports and then lifting from overhead with a forklift or loader Note It is VERY IMPORTANT not to lift the Sheep Auto Drafter by the Control Bridge as this action may damage it 3E2374 Sheep Auto Drafter User Manual ASSEMBLING THE SHEEP AUTO DRAFTER AND SORTING UNIT Assembling the Sheep Auto Drafter The Sheep Auto Drafter should be assembled when you purchase it All you will need to do is attach the following e air supply e power supply e scale indicator if using e RFID reader if using e sorting unit s if using Attaching the scales indicator and RFID reader To find out how to do this see How to turn the Sheep Auto Drafter on p 28 Assembling the sorting unit After you purchase the sorting unit you will need to assemble it The following ins
45. to Drafter and the pneumatic gate operation mean that it is exceptionally quiet when working This reduces the stress on you and stock Stock will flow better and will enter the unit more readily as a result Carry out several stock management tasks at the same time The Sheep Auto Drafter can automatically read EIDs weigh and then draft without you having to control it All of these actions can be pre programmed into a scale indicator which will communicate with the Sheep Auto Drafter This gives you the freedom to move away from the weighing and drafting area to organise stock at the same time as these actions are occurring Easy allocation and drafting of stock into different management groups Providing your brand and model of weighing indicator supports it it is a simple process to allocate animals into groups so that they can be managed differently This could include such things as the division into different groups by weight to allow priority feeding or the drafting out of ewes with multiple pregnancies Improve stock flow through the weighing and drafting system As there is less human involvement in the weighing and drafting process stock feel less threatened and more inclined to move freely through the system Decrease drafting and weighing operator errors and hit the correct target market weight when drafting 3E2374 Sheep Auto Drafter User Manual As the weighing and drafting processes are automated there is less chance of er
46. tructions explain how to do this Figure 7 Drafting unit components Tools required e 3 8in socket e 13mm socket e 17mm combination spanner Page 15 3E2374 Sheep Auto Drafter User Manual Method 1 The sorting unit will be assembled upside down so place the roof upside down on the ground 2 Attach the two tie bars to the rear of the roof and screw them on with two Tek screws 14 gauge x 50mm There is a left and right hand side the inside edge will be stepped in see photo below Tool required 3 8in socket stepped in edge attaching Tek screws 3 Attach doors by inserting shafts in holes in the roof The left and right doors are different so make sure the bolt to attach the air cylinders is on the Page 16 3E2374 Sheep Auto Drafter User Manual inside The door pivot tubes should be inserted with the white bolt guide into the roof inside edge bolt to attach air cylinder 4 Attach the floor by inserting the door pivot tubes and tie bars into the holes in the floor the back and front tubes are different sizes those at the drafting gate end are smaller so make sure you have the floor around the right way Keeping the floor level as you push it on will make the job easier 5 Drop the 4 through bolts into each corner of the floor and tighten do not over tighten Tool required 13mm socket Page 17 3E2374 Sheep Auto Drafter User Manual 6 Fasten the two air cylinders to the do
47. try gate will still open and shut automatically to let animals in and hold them in the unit but you will be in control of when they are released and the direction they are released in To hold an animal in the Sheep Auto Drafter Use the remote control to manage the release function if you would like to hold an animal in the unit This is useful if you want to examine an animal for some reason e g an animal health issue or for tagging an animal 1 Wait for the unit to open the entry gate and capture the animal then press the Retain Release button on the remote control This will prevent the exit gate from opening The white LED mode lamp will begin to flash Once you have dealt with the animal press the Retain Release button again The exit gate will open and the animal will be released Then the entry gate will open and the next animal will be captured To manually set the drafting direction Use the remote control to set the drafting direction if you would like to override an automatic drafting decision or you are in Manual Release Mode and you are making all of the drafting decisions yourself 1 Wait for the unit to open the entry gate and capture the animal then press the Retain Release button on the remote control This will prevent the exit gate from opening The white LED mode lamp will begin to flash Press the appropriate arrow on the remote control OOO to set up the drafting
48. utton down for around 1 second it is situated on the Control Bridge see Figure 14 Don t press it for 2 seconds or more as you will turn the Sheep Auto Drafter off The red LED fault lamps will turn on solidly and after 3 seconds the white mode LEDs will flash the fault code after which the red LED fault lamps will remain solidly on for a further 3 seconds before resuming their 1 second flash rate Once you nae determined what the issue is and you have fixed it then press the Start S or Retain Release button on the remote control to continue or press the Entry Gate button on the Control Bridge Ifthe fault hasn t been fixed the fault LED will continue flashing lf fault has been fixed the fault LED will turn off and the Sheep Auto Drafter will begin operating again 3E2374 Sheep Auto Drafter User Manual If you press Start on the remote control or the Entry Gate button on the Control Bridge then the unit will continue in Automatic Release Mode If you press Retain Release then it will continue in Manual Release Mode Note You are able to switch the Sheep Auto Drafter off using the Power button on the Control Bridge when it has a fault but you will need to resolve the issue when you next start it up before it will operate correctly i e if the fault lamps are flashing when you switch it off they will resume flashing when you next start it up Issue checklist and possible solutions If the red faul
Download Pdf Manuals
Related Search