USER MANUAL
Contents
1. 2MP IR PRO PTZ DOME IPTZ IR20A IPTZ IR30A ENHANCE YOUR NVR WITH OUR WIDE RANGE OF QVIS IP CAMERAS OUR PRODUCTS ARE FULLY TESTED TO WORK TOGETHER o we IP INTERNAL DOME IP BULLET DONT SETTLE FOR LESS ALL OUR PRODUCTS CARRY QUIS LOGOS Copyright Qvis 9 All documentation rights reserved Welcome Thank you for purchasing the 2MP IR Pro PTZ Dome Camera This user s manual is designed to be a reference tool for the installation and operation of your system Here you can find information about the corresponding IP camera s features and functions as well as a detailed installation method Before installation and operation please read the following safeguards and warnings carefully Copyright Qvis 9 All documentation rights reserved Precautions 1 Electrical safety e All installation and operation here should conform to your local electrical safety codes e The power supply shall conform to the requirement in the SELV Safety Extra Low Voltage and must make sure that the limited power source is rated 12V DC or 24V AC Please note Do not connect two power supplying sources to the device at the same time it may result in device damage We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation Weare not liable for any problems caused by unauthorized modification or attempted repair N Transportation Security2. IR LED WIPER IDLE ALARM ADVANCED OTHERS BACK ADVANCED AUX SOFT LIMIT DOME SPEED POWER ON ACTION TILT ANGLE BACK DOME SPEED SETTING DOME SPEED 180 S BACK EXIT Copyright Qvis 9 All documentation rights reserved 46 3 9 POWER ON ACTION MAIN MENU The user can define the dome action when power is on Move the cursor to POWER ON LANGUAGE ENGLISH ACTION and click IRIS to enter the setup INFORMATION DOME SETTINGS NONE default No action MOTION PRESET Dome goes to preset Default as RESTART Preset 1 FACTORY DEFAULT SCAN Dome starts auto scan Default as EXIT Auto Scan 1 Dome runs auto cruise Default as Auto Cruise 1 DOME S EEINCS PATTERN Dome runs pattern Default as Pattern 1 IR LED WIPER IDLE ALARM ADVANCED OTHERS BACK ADVANCED AUX SOFT LIMIT DOME SPEED POWER ON ACTION TILT ANGLE BACK POWER ON ACTION POWER ON ACTION NONE BACK EXIT Copyright Qvis 9 All documentation rights reserved 47 3 10 TILT ANGLE MAIN MENU The user can set up the tilt angle under the menu of TILT ANGLE LANGUAGE ENGLISH NUS Move the cursor to TILT ANGLE and click DET IRIS to the setup of tilt angle Click the Dd up or down button to select the angle and RESTART click the IRIS to confirm FACTORY DEFAULT EXIT DOME SETTINGS IR LED WIPER IDLE ALARM ADVANCED OTHERS BACK ADVANCED AUX SOFT LIMIT DOM
3. Normal Linkage Other Linkage Audible Warning v Notify Surveillance Center Trigger Channel C Capture Trigger Alarm Output Select All Capture Upload FTP Capture Upload Mail Capture storage SD card Picture 2 2 5 33 Arming Schedule Linkage Method After finishing setting up parameters click the confirm key to save the settings e Event Video Tampering When the the Enable Video Tampering box is ticked the IP camera video tampering function will be enabled This means the camera will log an alarm trigger if the camera lens is covered either mistakenly or maliciously See picture 2 2 5 34 Area setting default is set to whole screen Copyright Qvis 9 All documentation rights reserved 33 Slider sensitivity scale Sensitivity 0 100 After related parameter has been revised click save to save related Pd Parameter Configuration Motion Detection Video Tampering Exception Enable Video Tampering Area Setting 2004 01 19 16 19 15 Event Sensitivity Picture 2 2 5 34 Video Tampering e Event Exception Exception Type includes HDD FULL HDD Error Network Disconnected and IP address conflict See Picture 2 2 5 35 Normal Linkage includes Notify surveillance Center and Capture Other Linkage includes corresponding alarm output channel After modifying related parameters click save to save settings Parameter ConfiaurabDor
4. ZOOM MATCH OFF AUX OFF ENABLE OFF TRAKING SCENE SET BACK EXIT TRACKING SCENE SET TRACKING SCENE SET DELETE RETURN DELAY 10SEC Copyright Qvis 9 All documentation rights reserved Under the auto tracking mode the dome will auto track any detectable moving objects entering camera s view When the object is moving out of the scene the dome will return to a preset position as defined after the defined time 1 SENSITIVITY The user can set up the auto tracking sensitivity under this menu When set as LOW the dome will auto track an obvious object when it has entered the camera s view When set as HIGH the dome will auto track when small object when it has entered the camera s view Move the cursor there and click the IRIS to enter The options include LOW MID and HIGH TARGET To set up the size of the tracking object The options include Large MID and SMALL AUX If set to ON here the object auto tracking will activate an alarm aux output at the same time Click IRIS to enter to select ON or OFF ZOOM MATCH Under the auto tracking model if turning on the ZOOM MATCH function the dome will zoom in and out when it is auto tracking to keep the right proportion between the object and background Move the cursor there and click the IRIS to enter And click the up or down to select the optical zoom ENABLE Move the cursor here and click IRIS to en
5. 5 5 Image e Image Display Settings A Enter the image configuration interface see picture 2 2 5 21 image configuration illustration see sheet 2 2 5 22 J Parametar Conigeruion Display Settings OSDO Settings Text Overlay Privacy Mask 3 2004 61 19 16 06 39 image Adjustment Network Y Exposure Settings Focus Settings Image Y White Balance Picture 2 2 5 21 Display settings Copyright Qvis 9 All documentation rights reserved wa Backlight Settings Image Enhancement Video Adjustment 25 Off left right up down center Sheet 2 2 5 22 Image parameters Sharpness the higher the value the clearer the image edge will be Although if you raise the sharpness value it may make the picture look distorted Focus mode in auto mode the device automatically focuses according to changes in the monitored scene in front of the camera Semi automatic mode focuses once after the user controls the PTZ movement and zoom functions but if the scene changes it will not automatically focus again Manual only the user can adjust the camera s focus Min Focus distance the distance from lens to scene is nearer than the one within the settings the camera will not focus clearly Exposure mode settings available to adjust are as follows auto manual Iris and shutter Only exposure bias open the compensation level can be adjusted as well Vi
6. ALARM NO 1 CONTACT N O ALARM MODE OFF ACTION NONE ALARM OUT OFF RESET DELAY 10 SEC ALARM OUT Move the cursor to ALARM OUT Click IRIS to enter and click up or down button to select one of the alarm output channel options OFF DUTPUT1 OUTPUT2 ALL which are used to set the link alarm output signal switch after receiving alarm input signal s RESET DEL AY Move the cursor to the ALARM OUT Click IRIS to enter and click up or down button to select a reset delay time 10SEC 30SEC 1MIN 5MIN 10MIN This settings dictates the length of time that the speed dome has BACK from alarm signals detection to alarm reset and return back to normal The setting is valid under AUTO ALARM MODE Copyright Qvis 9 All documentation rights reserved 43 3 AUX The user can set up the auxiliary output to trigger MAIN MENU other devices such as an alarm or a controller LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT Move the cursor to AUX and click IRIS to enter and click up or down button to select ON OFF then click IRIS to confirm DOME SETTINGS IR LED WIPER IDLE ALARM ADVANCED OTHERS BACK ADVANCED AUX SOFT LIMIT DOME SPEED POWER ON ACTION TILT ANGLE BACK AUX1 OFF AUX2 OFF Copyright Qvis All documentation rights reserved 44 3 8 Copyright Qvis 9 All documentation right
7. Mask IPv6 Default Gateway IPv6 DNS Server PPPoE FIP UPnP Email Port Mapping WIFI 58 04 CB 00 27 59 192 168 0 99 255255 255 0 192 168 0 1 192 168 0 1 Picture 2 2 5 6 TCP IP interface Copyright Qvis 9 All documentation rights reserved 17 e System Port Port screen includes HTTP Port the default is 80 RTSP Port the default is 554 and HTTPS Port the default is 443 Through network access to the device users can set the corresponding port After modifying the parameters click Save to save the settings See Picture 2 2 6 Note TCPAP Pot DDNS HTTP Port Network RTSP Port HTTPS Port Reboot the IP camera after modifying the parameters PPPoE FTP UPnP Email PortMapping WIFI 80 554 443 Network Picture 2 2 5 7 port configuration screen Network DDNS Enter DDNS settings screen the tick box allows you to enable DDNS function DDNS Types include Oray or Noip See picture 2 2 6 8 When set to either DDNS types you will need to fill in Server address The server address is DNS server s address software operator The Domain is the name set by the user The port can be set according to the configuration User name and password are will need to be created and confirmed After modifying related parameters click Save to save settings TCPAP Port DDNS PPPoE FTP UPnP Email Port Mapping WIFI C Enable DDNS DDNS Type oray Server Addre
8. OK and the plugin will be downloaded You can also double click the icon at the top right corner of the login interface to download plugin see Picture 2 2 1 1 highlighted by the red box Double click the downloaded WebPluginInstaller exe and start amp complete the installation for web browser You need to return to the web browser screen and refresh the display press F5 key if you want to run this plug in after installation then you will be able to watch the preview video stream from the camera Copyright Qvis 9 All documentation rights reserved 8 New version of plugin is detected Update it OK Cancel Picture 2 2 2 1 Plug in installation After you have installed the plug in input user name code and then click the login button to enter the preview screen See 2 2 2 2 Live View Configuration Log PlayBack gt Main Stream Sub Stream 43 160 x1 Ri gt gt v a v 2004 01 19 15 26 32 a 4 O gt E M A Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 Precet 7 iv Picture 2 2 2 2 Preview screen OO O C Tee Tee SC TI ow 5 E e Sheet 2 2 2 3 Preview screen information O Copyright Qvis 9 All documentation rights reserved Icon Instruction Control the vertical and horizontal movement of camera and open or close the auto scan lad zpe ome 9m 8 PTZ speed SERGE SCHER Lm o m Low o mm Sheet 2 2 2 4 PTZ control screen informa
9. Please ensure that the product does not endure heavy stresses violent vibration or contact with water during transportation storage and installation Please use the original packing material or the material of the same quality if you need to return it to vendor 3 Installation e Do not apply power to the product before completing installation Do not put object s on the product Please install a proper power cut off device during the installation connection 4 Qualified engineers needed All the examination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorised modifications or attempted repair 5 Environment This product should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc e Please keep it away from environments that contain electromagnetic radiation or objects that produce it Please keep sound ventilation around the device at all times Copyright Qvis 9 All documentation rights reserved Do not allow the water and other liquid to penetrate into the device if casing has been compromised This series product complies with the IP66 standard specified in the Degrees of Protection Provided by Enclosure Ensure lightning surge protection is in place to make sure you fully protect camera circuitry from electrical overload Please make sure the CCD CMOS component is away from the
10. User addition click Addition camera will display addition box where you will need to input user name password and user level administrator user observer Then click ok to create user See picture 2 2 5 27 User modify Choose the user name you wish to modify click modify to enter interface In this box the user needs to modify user name and password see picture 2 2 5 28 Delete user choose the user name you wish to delete a dialog box will appear click confirm to delete the user Live View Configuration Log PlayBack 4 User RTSP Authentication Anonymous Visit IP Address Filter Addition Serial Number User Name Level admin Administrator Safety 2 2 5 26 User Settings Level Administrator D Password Password Confirm OK Cancel Picture 2 2 5 27 Addition Copyright Qvis 9 All documentation rights reserved 29 Modify user User Name Level uf Password Confirm OK Cancel Picture 2 2 5 28 Modify user e Security RTSP Authentication The authentication can be set as either disable or basic from the drop down list options Disable closes RTSP authentication Basic enables RTSP authentication After modifying the parameters click Save to save the settings See Picture 2 2 5 29 A Parameter Configuration User RTSP Authentication Anonymous Visit IP Address Filter RTSP Authentication Disable v Safety Picture 2 2 5 29 RTSP
11. Video Audio In the audio configuration the Audio Encoding options only contain G 711U version Audio Input options include Line in and Mic in If using an active pickup then select the Line in option if for passive microphone choose Mic in Input volume is the input source gain control value the default value is 50 The user can adjust the level in between 1 100 according to the actual volume requirements Copyright Qvis 9 All documentation rights reserved 23 After modifying the related parameter you need to click Save to save settings oee picture 2 2 5 18 for the Audio configuration interface audio configuration parameters shown in picture 2 2 5 19 Note after modifying audio encoding please reboot the device Video Audio ROI Audio Encoding G 711U v Audio Input Line In v Audio Video Input Volume a 100 Picture 2 2 6 18 Audio setting Audio encoding G 711 ulaw Audio input Mic in Line in optional Input volume O 100 optional Picture 2 2 6 19 audio parameter instruction e Audio Video ROI The video stream concentration makes the video camera s video preview image clearer Use the sliders to adjust the Region Number and ROI Level Copyright Qvis 9 All documentation rights reserved 24 Video Audio ROI mem 2004 81 19 15 59 42 Fixed Region Enable Region Number 1 v ROI Level 1 v Picture 2 2 5 20 ROI 2 2
12. can be set according to the actual situations For Time Sync set NTP server address NTP port and Interval minutes The device will time sync according to the setup time For Manual Time Sync set time and check Sync with computer time then the time of the camera syncs with the local PC After changing some parameters you need to click Save to save the corresponding settings See picture 2 2 5 4 Note You cannot change the NTP port number Copyright Qvis 9 All documentation rights reserved 15 System Time Zone GMT 08 00 Beijing Urumqi Singapore Set Time 2015 05 16 11 04 13 Sync with computer E Picture 2 2 5 4 Time settings e System Maintenance Enter system maintenance interface See picture 2 2 6 5 Click Reboot to reboot the device Click Restore to restore device parameters It will easily restore the other parameters except IP address subnet mask gateway 8000 port number DNSS address and user name management information Click Default and it will completely restore device parameters to default settings Parameter import Import Config File will allow you to install a particular configuration file parameter export will export current configuration file Click Export then it will be exported to PC after 59 seconds then it will automatically go to the Web login interface Click Browse choose local upgrade file or upgrade catalogue then click upg
13. check the following steps to set up cruise SEQ NO Move the cursor here and click IRIS to enter the Sequence Number setup Click the up or down button to select a preset number 1 8 and click IRIS to confirm TITLE Move the cursor here and click IRIS to enter the Sequence Title setup Check the details above in DOME TITLE Settings lt SEQUENCE SET gt Move the cursor here and click IRIS To enter Move the cursor to EDIT and click IRIS enter Edit mode of sequence Move the left and right button to select each item a When the lt gt is on the item NO move the up or down button to select the Serial NO Of the preset in a sequence There are up to 32 presets in each sequence b When the lt gt is on the item PRESET move the up or down button to select the preset NO That the user wants to add in the sequence c When the lt is on the INTERVAL move the up or down button to select the interval time between each preset d When the is on the last item move the up or down button to select edition mode as INS insert ok and delete e Click IRIS when selecting INS to insert the settings into the position of current Serial No f Click IRIS when selecting OK to override the settings of Current Serial No g Click IRIS when selecting delete to delete the settings of the Current Serial No h Click IRIS to save all the setting and click IRIS CLOSE to exit DELETE START Move
14. icon Motion Detection Video Tampering Exception Type HDD Full v Normal Linkage Other Linkage C Notify Surveillance Center Capture Capture Upload FTP Trigger Alarm Output 7 Select All Capture Upload Mail Capture storage SD card Picture 2 2 5 35 Exception Copyright Qvis 9 All documentation rights reserved 34 e Storage Record Schedule Tick the Enable Record Schedule then click Editor button to edit the record schedule Appoint record period s and the choose record type See picture 2 2 5 36 For edit schedule see picture 2 2 5 37 Record time includes All day and Section If user chooses Section the user is able to choose a specific time period Supports up to 4 record period settings Record types include Timing Motion Detection Alarm Motion Or Alarm Motion and Alarm Other Pre record is the advanced pre record time before starting of record 0 3sec optional Post record is the delayed continued time of recording 5sec 10min optional After modifying related parameters click Confirm to save settings Note Overwrite is measured according to 2Mbps the bigger stream you choose the shorter the pre record time is Record Schedule Storage Management Capture Pre record 5s v Post recor d 5s v Overwrite Yes v Enable Record Schedule ll Timing 0 2 4 6 8 10 12 14 16 18 20 22 24 E Motion Detection E Alarm E Mo
15. positions user defined dwell time 4 patterns up to 500 instructions per pattern The dome will rotate back to preset position after a period of vacant time 0 90 35 C 60 C OSD Menu Operation e Call up OSD menu Call Preset 95 to enter the main OSD menu call Preset 96 to close the OSD menu or Select Exit Copyright Qvis 9 All documentation rights reserved 4 e Confirm The Left and Right button is controlled by PTZ can change the required item and the changed item is the confirmed one without further confirmation You can directly click Up and Down button to go on your further operation When setting the left and right boundary for scan and pattern you can click the Focus Far for confirmation e Cancel The up and down button controlled by PTZ carry out the request for Further action meanwhile it carries out the Cancel order for last operation Copyright Qvis 9 All documentation rights reserved 2 Web Browser Operation Guide 2 1 Common Operations 2 1 1 Factory settings An IP camera is classified as a type of network equipment you need to configure its network IP address gateway and other information to fit within the network it is being integrated into The camera comes with a default factory IP address which the user can change it according to their setup requirements Default factory IP settings Default IP address 192 168 0 99 Subnet mask 255 255 255 0 Gatewa
16. radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage e itis recommended that the grounding studs of the product should be grounded so to further enhance the reliability of the camera Avoid shooting very bright objects directly into the camera s CCD such as the sun or light fittings and avoid fixating the camera lens on bright static object for long time as it will cause Irreparable damage to the camera s CCD 6 Daily Maintenance e Please shut down the device and then unplug the power cable before you begin any maintenance work e Do not touch the CCD CMOS optic component Please use an air jet to clean the dust off the lens surface You can use the dry cloth with some alcohol or mild detergent to clear if necessary e When the camera is not in use please put the dustproof cap to protect the CCD CMOS component e Do not use volatile solvent such as the benzene paint thinner or detergent with the ability to abrade surfaces It may result in lens damage or adversely affect the device s performance T Accessories Always use all the accessories recommended by manufacturer Before installation please open the package and check that all the components are included Contact your local retailer vendor ASAP if something is missing Copyright Qvis 9 All documentation rights reserved Table of Contents 1 General and Technical Features IRI mnR rene remer ret ene re se
17. rec Save downloaded files to C Documents and Settings Administrator Application Data WebNP dos Browse Picture and Clip Settings Save snapshots in live view to C Documents and Settings Administrator Application Data WebNP cay Save snapshots when playbackto C Documents and Settings Administrator Application Data WebNP dos Picture 2 2 5 1 TCP UDP optional shortest delay real time balanced Live video performance fluency optional Display Code Rate Display hide optional Audio noise reduction Open close optional Save snapshots in live view to Picture 2 2 5 2 configuration information Copyright Qvis 9 All documentation rights reserved 14 2 2 5 2 System e System device information In Device Information screen users can set the Device Name Model Serial No Firmware Version Encoding Version Number of Channels Number of HDDs and Number of Alarm input and output See picture 2 2 5 3 System Basic Information Model Seria I No 0027593D0089BE AOD 1 Program Version 1 0 2 Build 201504300916 Control Version MiniPtz V1 02 build201504171316 Web Page Version 1 1 1 Build 20150430 Plugin Version 102 38 Number of Channels 1 Disk Quantity Number of Alarm Input Number of Alarm Output Memory 111 132 Picture 2 2 5 3 device information e System Time settings In the Time Settings screen time sync is operational Time Zone shows the current IP camera s time zone and that
18. to use it to configure the camera 3 1 INFORMATION MAIN MENU LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT INFORMATION VERSION TEMPERATURE 32 C VOLTAGE 12v BACK EXIT The user can review the camera s system information for reference The information provided can include Dome ID dome address baud rate protocol temperature voltage alarm information dome title version date time and temperature scale Use the following steps to display the System Information screens 1 Move the cursor to INFORMATION 2 Click IRIS to enter the INFORMATION screen opens 3 Click up or town to select the item 4 Click IRIS to confirm the setup of each item Copyright Qvis 9 All documentation rights reserved 38 3 2 LANGUAGE MAIN MENU The user can choose and set OSD menu language The device supports either Chinese English LANGUAGE ENGLISH Location and configuration method INFORMATION DOME SETTINGS Click IRIS to enter and click up or down button to MOTION select RESTART FACTORY DEFAULT All on screen menus will be changed to the selected EXIT language LANGUAGE LANGUAGE CHINESE BACK EXIT Copyright Qvis 9 All documentation rights reserved 39 3 3 IR LED User can configure the IR LED working mode via the IR LED options within the DOME SETTINGS LANGUAGE ENGLISH menu The configuration options are as follows
19. 2 2 5 23 OSD Settings Copyright Qvis 9 All documentation rights reserved 27 e Image Text Overlay Camera supports text overlay within the image Supports a maximum of 40 characters see picture 2 2 5 24 Input the text overlay characters into box and then tick corresponding character number The user can preview the input character Using the mouse drag the mouse cursor across preview window to choose display location which will show the text overlay click Save to confirm characters will show within the image Parameter Configuration d Paran dn Display Settings OSD Settings Text Overlay Privacy Mask 2004 81 19 16 85 11 Enable character overtay Picture 2 2 5 24 Text Overlay e Image Privacy mask User can enable and set up to 4 privacy mask areas depending on their needs See picture 2 2 5 25 P Parameter Configuration Display Settings OSD Settings Text Overlay Privacy Mask 2604 61 19 16 06 24 x Whether enable video covering Of Video Cover Area1 Video Cover Area2 Video Cover Area3 Video Cover Area4 Picture 2 2 5 25 Privacy Mask Copyright Qvis 9 All documentation rights reserved 28 2 2 5 6 Safety e Safety User Enter the Safety configuration menu the user can set user information select administrator admin and also create other user accounts according to how many users will have access to the camera A maximum of 8 users can be created See picture 2 2 5 26
20. 9 ackets Sent 4 Received 4 Lost 0 0 loss EN round trip times in milli seconds inimum ms Maximum ms Average Oms As the picture shown above it indicates that there has been a successful connection between the computer and the camera However if the screen display like this pinging 192 168 0 99 with 32 bytes of data Request timed out Request timed out Request timed out Request timed out ping statistics for 192 168 0 99 ackets Sent 4 Received 0 Lost 4 100 loss This indicates a connection failure To solve the connection issue please check the following e lf the hardware is correctly connected together e f computer TCP IP is within the same segment as the camera e f network forbids the ping order please contact the network administrator to gain permission Copyright Qvis 9 All documentation rights reserved 2 2 Web Login 2 2 1 Login Open up web browser within the Windows interface enter default factory IP address 192 168 0 99 to open the camera s web interface A dialog box will be shown as follows Net Camera Anonymous Login Picture 2 2 1 1 login interface e User name Admin e Password Admin e Port Default 8000 2 2 2 Download playing component After you have logged in if the WEB browser indicates this is the first time you ve logged in and will ask for you to install the latest plug in version See Picture 2 2 2 1 Click
21. DM Percentage of Picture ED Percentage of Record 59 Picture 2 2 5 38 Storage management Copyright Qvis All documentation rights reserved 36 e Storage Capture Setup snapshot capture to coincide with the record schedule s parameters See picture 2 2 5 39 Format provides the option to capture snapshot in the JPEG image format Resolution is current main stream s resolution Quality gives user to choose either High Middle Low image quality settings Interval will allow the user to set interval time length Units available to choose from millisecond second minute hour day Interval can range from 1 to 604800 milliseconds After modifying the related parameters click Save to save settings Record Schedule Storage Management Capture Timing C Enable Timing Snapshot Format Resolution Quality Storage Interval Capture Linkage C Upload to FTP Upload to E mail C Capture Storage SD Card Picture 2 2 5 39 Capture Copyright Qvis 9 All documentation rights reserved 37 3 OSD MENU FUNCTION The OSD On Screen Display menu of the camera can be viewed either within the live footage preview screen on the Web connection interface or via a display monitor connected to an NVR that has a connection to the camera You can navigate through the OSD menu via controls found within the camera This chapter will show you the available OSD options and how
22. E SPEED POWER ON ACTION TILT ANGLE BACK TILT ANGLE SETTING TILT ANGLE O BACK EXIT Copyright Qvis 9 All documentation rights reserved 48 3 11 OTHERS MAIN MENU The user can set up TEMP MODE INTERNAL FAN PRESET FREEZE STOP TIME MENU LANGUAGE ENGLISH OFF TIME and NORTH ZERO here under the INFORMATION OTHERS menu DOME SETTINGS MEETS 1 TEMP MODE To set up the control mode RESTART of the dome s fans and heaters It includes FACTORY DEFAULT three modes AUTO FAN HIGH SPEED EXIT and FAN LOW SPEED 2 AUTO FLIP When the camera tilts downward and goes just beyond the DOME SETTINGS vertical position the camera will rotate 180 degrees The user can click IRIS 4 to IR LED enter and choose to turn on off this WIPER function IDLE ALARM 3 MENU OFF TIME To set up the time that ADVANCED the OSD menu will turn off when there are OTHERS no operations Options include 1 2 5 10 min BACK 4 AZUIMUTH ZERO To set up the due north of the dome pan 0 Move the cursor here and click IRIS to enter Click the up or down button to control the dome to pan 0 and click IRIS to confirm OTHERS TEMP MODE AUTO AUTO FLIP ON STOP TIME 30 SEC MENU OFF TIME 5 MIN lt DISPLAY gt lt AZIMUTH ZERO gt Copyright Qvis 9 All documentation rights reserved 49 3 12 PRESET MAIN MENU LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT MOTION PRES
23. ET SCAN SEQUENCE PATTERN AUTO TRACKING BACK PRESET SCAN SCAN NO 1 TITLE START LEFT LIMIT RIGHT LIMIT CALL DELETE SCAN SPEED 20 BACK Copyright Qvis 9 All documentation rights reserved The dome supports 220 presets Please check the following steps to set up a preset 1 PRESET SCAN NO Move the cursor here and click IRIS to enter the setup of Preset Number Click the up or down button to select a preset number 1 64 and 100 255 and click IRIS to confirm TITLE Move the cursor here and click IRIS to enter the setup of Preset Title Check the detailed above in DOME TITLE settings LEFT LIMIT Move the cursor here and click IRIS to enter Move the dome to a defined position as left limit and click IRIS to save this left boundary RIGHT LIMIT Move the cursor here and click IRIS to enter Move the dome to a defined position as right limit and click IRIS to save this right boundary CALL Move the cursor here and click IRIS 4 to call up the current preset DELETE Move the cursor here and click IRIS to delete the current preset SCAN SPEED Move the cursor here and click IRIS to set up the preset call up speed of LOW MID and HIGH 50 3 13 AUTO SCAN MAIN MENU LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT MOTION PRESET SCAN SEQUENCE PATTERN AUTO TRACKING BACK SCAN NO 1 TITLE START LEFT
24. INFORMATION eee 1 CONTROL MODE MOTION RESTART FACTORY DEFAULT EXIT according to light conditions and Close Times OPEN IR LED kept constantly open CLOSE IR LED kept constantly closed CAMERA IR LED status Open Close will be synchronised with Camera s day and night switch set up DOME SETTINGS IR LED WIPER IDLE ALARM ADVANCED 2 SENSITIVITY OTHERS Here the user can manually set the BACK sensitivity from 1 5 The smaller the number is the lower the light level of the environment will be when the IR LEDs are turned on 3 NEAR FAR POWER COMPENSATION When near power opens or far power opens according to the power setting you can set the near far power compensation to either 10 20 30 40 50 CONTROL AUTO SENSE 4 6 NEAR POWER 10096 FAR POWER 10096 COMPENSATION 096 AUTO CONTROL OFF AUTO CONTROL BACK EXIT 4 AUTO CONTROL When the IR LEDs are on they will turn its power consumption to the standby status which will effectively extend the service life of IR LEDs And under this mode when objects appear in the screen the IR LED will turn its power consumption back to the normal status AUTO CONTROL STANDBY POWER 50 DELAY 10SEC SENSITIVITY MID Copyright Qvis All documentation rights reserved 40 3 4 WIPER MAIN MENU The user can make adjustments to the lens wiper under this menu suitable for LANGUAGE ENGLISH wiper equipped dome INFOR
25. LIMIT RIGHT LIMIT SCAN SPEED 20 BACK Copyright Qvis 9 All documentation rights reserved The dome supports auto scan 8 groups Please check the following steps to set up a scan 1 SCAN NO Move the cursor here and click IRIS to enter the setup of SCAN Number Click the up or down button to select a preset number 1 8 and click IRIS to confirm TITLE Move the cursor here and click IRIS to enter the setup of SCAN Title Check the detailed above in DOME TITLE settings START Move the cursor here and click IRIS to start the current scan LEFT LIMIT gt Move the cursor here and click IRIS to enter Move the dome to a defined position as left limit and click IRIS to save this left boundary RIGHT LIMIT Move the cursor here and click IRIS to enter Move the dome to a defined position as right limit and click IRIS to save this right boundary SCAN SPEED Move the cursor here and click IRIS to set up the scan speed ranging 1 30 51 3 14 AUTO CRUISE SEQUENCE The dome supports 8 auto cruise groups and each cruise MAIN MENU LANGUAGE ENGLISH INFORMATION 1 DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT 2 MOTION 3 PRESET SCAN SEQUENCE PATTERN AUTO TRACKING BACK SEQUENCE SEQ NO 1 TITLE START lt SEQUENCE SET gt INTERVAL 005 BACK SEQUENCE 1 Copyright Qvis All documentation rights reserved supports 32 presets Please
26. MATION DOME SETTINGS 1 Number MOTION RESTART Move the cursor to NUMBER and click FACTORY DEFAULT IRIS to enter the wiper setup preset EXIT number Click the up or down button to select number 1 10 and then click IRIS to confirm DOME SETTINGS 2 IR LED WIPER IDLE ALARM ADVANCED OTHERS BACK Speed Move the cursor to SPEED and then click IRIS to enter the Wiper speed setup Click the up or down button to select HIGH MID or LOW then click IRIS to confirm 3 Reset Move the cursor to RESET and click IRIS to reset wiper settings 4 Activate NUMBER 03 SPEED MID Move the cursor to ACTIVATE and AUX ON AUX1 click IRIS to ACTIVATE wiper preset RESET The wiper will be activated ACTIVATE Note Calling the preset number 71 can also enable the wiper Copyright Qvis 9 All documentation rights reserved 41 3 5 IDLE MAIN MENU User could set camera to idle via the DOME LANGUAGE ENGLISH SETTINGS OSD menu options INFORMATION 1 Action DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT DOME SETTINGS IR LED WIPER IDLE ALARM ADVANCED OTHERS BACK IDLE ACTION TIME 30 SEC ACTION NONE Copyright Qvis 9 All documentation rights reserved Click up down key to highlight ACTION click left right key enter setting mode click left right key to choose idle action Action options include no action preset 1 auto scan auto cruse an
27. Setting screen e Security Anonymous Visit You will be able to choose either enable and disable from the drop down list choosing enable will allow a user to login to the anonymous Copyright Qvis 9 All documentation rights reserved 30 camera web interface When the user logs in as anonymous they will only have access to the live preview video footage from the camera The will not have access to the playback log and configuration interface See picture 2 2 5 30 When you enable anonymous visit the next time a user logs into the camera via their web browser the login section will have anonymous option to tick Tick anonymous then click the login button user will then be able to login directly User RTSP Authentication Anonymous Visit IP Address Filter Anonymous Visit Disable v Safety Picture 2 2 5 30 Anonymous visit e Security IP address filter Tick the Enable IP Address Filter box to start this function This option will then allow the user under administrator login to add Friendly IP addresses to the list so they can be allowed to access to the camera The user can also provide IP addresses to be blacklisted i e to be denied forbidden login access to the camera To add an IP address to the list firstly select what list the IP address is to be added to from the IP Address Filter Type drop down options Click Addition to add new IP address after the addition is complete the u
28. ard Then the camera can scan between these boundaries It can support up to 8 scanning path groups 1 7 Cruising Track The preset position can be programmed to be recalled in a set of sequences This sequence can be set to let the camera scan from one position to the next in a cycle at a set speed This feature is called the auto cruise The cruise sequence and dwell time of each preset can be set It supports up to 8 cruising tracks each cruising track with 32 presets 1 8 Pattern Tour Camera can memorize 600 second running paths or 500 programmable instructions When starting a pattern tour the camera will move automatically according recorded action path It supports 4 groups of pattern tours Copyright Qvis 9 All documentation rights reserved 3 1 9 Technical Parameters Power Supply Decoder Manual Speed Preset Speed Pan Angle Tilt Angle Number of Preset Preset Accuracy Alarm input output Auto Scan Auto Cruising Pattern Tour Guard Location Operating Humidity Operating Temp 1 10 DC12V 41096 50W Built in Pan 0 019 360 S Tilt 0 019 1209 S high speed Pan 0 01 100 S Tilt 0 01 100 S Vair speed 360 S high speed 100 S Mid speed 360 continuous pan rotation 90 Auto Flip 206 0 1 1input 1 output 8 auto scan tracks user defined left and right boundaries and scan speed 8 cruising tracks each cruising tracks has 32 preset
29. ck contains 32 presets e 4 pattern tours with 10 Mins memory and 500 programmable instructions e Multiple protocols through RS485 e 8 auto scan with user defined left and right boundaries and settable scan speed e 8 settable Privacy Zones e Automatically compatible with PELCO P PELCO D e Guard Location the dome will rotate back to preset position after a period of non use e Alarm triggering the alarm can trigger preset auto scan cruising and pattern tours functions e Soft Address Function this can be used to set up the dome address without uninstalling the dome 1 3 Integrated Super Speed PTZ Rotator e otep less speed change with auto zoom amp speed matching e 360 Pan and 90 Tilt range auto flip without blind spot e Near far IR light auto adjusts to match when camera zooms in out Copyright Qvis 9 All documentation rights reserved 2 1 4 All Weather Outdoor Design e P66 Protection standard e TVS 3000V Protection standard 1 5 Preset Position Set Up and Call Up Within the Preset function the camera stores the current pan tilt angle zoom and other position parameters into memory When necessary the camera recalls these parameters and adjusts the camera to a particular position The user can store recall and clear the presets easily and promptly by using the keyboard controller The camera can store up to 256 presets 1 6 Auto Scan Users can set up the left and right boundaries by using a control keybo
30. creen Log screen can search show and output the log information stored upon the SD card within the camera Select the type of the log and set the start and end time of the log search Click the search key and all the eligible log information will be displayed in the list See 2 2 4 1 Click the Save key you can save the log information to your local computer Live View Conliqgurathon Log Play Back Tire Major Type Minor Type CH Parameter Local Reamote User Remote Host IF Search Log Major Type Al Types bd bur Type All Types Start Time 2015 05 16 DD DO End Time 2075 05 16 10 58 Search Picture 2 2 4 1 log record screen Copyright Qvis 9 All documentation rights reserved 13 2 2 5 Configuration 2 2 5 1 Parameter Configuration Click Configuration enter configuration interface To set local configuration select Local Configuration from the options list on the right side of the screen as shown in picture 2 2 5 1 each item instruction as shown in picture 2 2 5 2 Live View Configuration Log PlayBack r P Parameter Configuration Local Configuration Local Configuration Play Parameter Protocol Type O UOP TCP Live View Performance Shortest Delay Real Time Balanced Fluency Display Code Rate Display Hide Audio Noise Reduction Open C Close Record File Settings Record File Size 256M 512M O 1G Save record files to C Documents and Settings VAdministratorApplication Data WebNP
31. d pattern Once the action has been selected click the up down keys to set next operation Delay Click the up down key to select the Delay option click left right to enter setting mode click left right key to operate time choice 1 min 5min 10min Click up down key for the next step 42 3 6 ALARM The dome system has 4 alarm inputs and 2 alarm outputs optional function When an alarm signal is received to the MAIN MENU i input of the dome it triggers a user defined action such as a LANGUAGE ENGLISH presets patterns etc at the same time the alarm output INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT signal will be activated 1 ALARM NO Move the cursor to ALARM NO Click IRIS to enter and click up or down button to select the alarm input no 2 CONTACT Set the alarm contact status There are two input states OPEN and CLOSE 3 ALARM MODE Alarm function is deactivated Alarm function is activated AUTO AUTO Alarm function will be activated and deactivated between START TIME and STOP DOME SETTINGS IR LED WIPER IDLE ALARM ADVANCED OTHERS 4 ACTION Set the alarm action NONE default No action PRESET Dome goes to preset Default as Preset 1 SCAN Dome starts auto scan Default as Auto Scan 1 TIME BACK SEQ Dome runs auto cruise Default as Auto Cruise 1 ALARM SETTING PATTERN Dome runs pattern Default as Pattern 1
32. deo standard 50Hz 60Hz optional This section represents the refresh and frame rate of the video stream from the camera which you are given the opportunity to modify After modifying device needs to reboot When the user chooses 50Hz the real time frame rate is 25frame sec When 60Hz is set real time frame rate is 30frame sec Copyright Qvis 9 All documentation rights reserved 26 Mirror direction of symmetry includes left right up down center The video adjustment option is used to switch symmetry direction of image WDR On Off White balance Auto MWB Digital noise reduction This is used to adjust the level of noise point within the image It will also simultaneously reduce the detail of image Default when you click default all the parameters in this display setting box will resort back to factory default values e Image OSD setting User can set the channel name display name and date according to their needs Time format 24 hour time system 12 hour time system Date Format XX XX XXXX month day year y XXXX XX XX year month day Y XX XX XXXX day month year After modifying parameters click Save to save settings See picture 2 2 b 23 d m Display Settings OSDSetings Tex Overday Privacy Mask 0i 01 15 6 Ch 16 Display Name v Display Date Channel Name Image Time Format 24 hour time system Date Format YYYY MM DD ymd v Picture
33. enu Funchon enne nn nnn n nnne nenne nsns sn nnn ni i rrr nnn nennen Sel eiue mc c m 3 2 JLang sges Jmp BBAA d Ius 39 3 IRLeds ee ee ee ee T O ee ee Bee CRW ggf SA ET GEERT gege Q7 AUX eee ee B 38 WEB Ip eene e Wl um E6 Em o ome S99sC T M ENIM Power ON ACTION cotusevesexesssssi dete mE ec RI EC 3 14 Auto Scan Ze 20 00e senes eren nne nine rine 3 15 Auto Cruise Sequence eesssseeee n ea aaf e REIR 3 16 Pattern Tour 0 EB Ee A maw Tech nx E commos SNB Boestar D WELL d gH coc clon edeesdesugcdaeaec soo sser soc 220 Facts N ln nennen nnn nnnm nnne runner nnno rr Copyright Qvis 9 All documentation rights reserved 38 3 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 55 56 1 General and Technical Features 1 1 Special Features High Definition Footage Shoot video footage using MPEG H 264 compression at varying frame rates which allows you to save network bandwidth without compromising on footage quality You will also be able to adjust the aspect ratio of the video footage to either 16 9 or 4 3 Also supports dynamic coding within footage settings Fixed Focus Varifocal Automatic focusing In built in 20x 30x optical zoo
34. lated parameters need to click Save to save settings Copyright Qvis 9 All documentation rights reserved 19 Parameter Configuration Parameter Configuration TCP P Pot DONS PPPoE FTP UPnP Email PortMapping WIFI onfiguration Server Address 492 168 2200 Network Port 21 User Name Sy Anonymous Password Password Confirm mn Directory Structure save in the root directory 4 Parent Directory Child Directory Picture 2 2 5 10 FTP setting e Network UPnP Tick Enable UPnP and this function will make the device to be automatically located within the LAN For a camera located within an internal network the UpnP function will make a gateway or instruct the router to perform auto port mapping The camera maps the monitored network port via the gateway or router to an internal network device The gateway or router network firewall module will began to open this port to other computers on the Internet Users don t need to do port mapping forwarding within the routers settings The precondition is that the router supports UPnP and then opens this function See picture 2 2 5 11 b pa er Contar ation oi TCPAP Pott DONS PPPoE FIP UPnP Email PortMapping WIFI Enable UPnP Network Friendly Name IPHC 0027593D0089BEADD1 g ave Picture 2 2 5 11 UPnP configuration Copyright Qvis 9 All documentation rights reserved 20 e Network Email Enter email settings you will to fill in
35. m varifocal variable focus and automatic focusing function The automatic focusing function will adjust image to optimum clarity whilst changing the zoom amount and what direction the camera is pointing towards Double Stream Option Supports double streaming Main amp Sub streams Multiple Supported protocols Supports TCP IP PPPoE DDNS FTP UPNP Onvif etc Voice intercom function 1 x Audio In 2 x Audio Out Two Way audio ability Alarm function Supports local and wide area network signal linkage Link to a networked alarm system using the network input outputs Region of Interest ROI otream concentration makes the drawing region clearer OSD function Setup the camera with its onboard setup user interface via a connected monitor Copyright Qvis 9 All documentation rights reserved 1 1 2 Function Introduction e Pan 0 01 360 S Tilt 0 01 120 S Preset 360 S high speed IR speed dome e Pan 0 5 35 Tilt 0 5 35 Preset 35 s for Vari speed IR dome e Auto object tracking zoom in out and motion detection Auto Track Model e Schedule up to 7 days of programmable timed actions e Built in Semi conductor heater amp digital temperature sensor e PWM cooling fan with variable speeds to control temperature to a stable level e Reserved network interface and extra capacity for a extra network module e Pan Tilt accuracy 0 1 256 preset positions e 8 cruising tracks each cruising tra
36. movement and then click the right boundary Finally click the start key and the camera will move in the range of the left and right limit Click stop to stop the movement 3 It will be the same setting methods explained in the previous point above to set other auto scanning paths 2 2 3 Playback Click Playback to enter the video search playback screen The Playback screen can inquire playback and download effective video that has been saved on to the SD card of the camera Select the inquiry type start amp end time then click the Search key and the eligible video files will be displayed in the right box Select it and double click to open and then the video files will start to playback See 2 2 3 1 Copyright Qvis 9 All documentation rights reserved 12 Live View Confiquration Log PlayBack Query Type b e e v Oeotype 2015 01 17 14 55 36 Start Time 2015 05 21 00 00 End Time XA a ARNA Pi D E A m j Wen 000 g o e Serial Number Namera Date Size Download Progress Download Speed Picture 2 2 3 1 video playback Note playback function can only be used under the circumstance when the camera has an SD card installed If the camera has SD card and it is using it for the first time you must click the Storage key to initialise the SD card and set the video recording plan 2 2 4 Log Click Log key to enter the log inquiry s
37. rade to upgrade device version Status shows the current upgrade progress after the upgrade is complete you will be prompted that upgrade was successful Note The upgrading process will take around 1 to 10 minutes please do not disconnect power to the device during the process The device reboots automatically after the device has been upgraded Copyright Qvis 9 All documentation rights reserved 16 System 2 2 5 3 Network Device Information Reboot Time Settings Maintenance Reboot Reboot the device Mobile Monitor S Close Sae gt s Default Restore Resetallthe parameters except the IP parameters and user information to the default settings Default Restore all parameters to default settings Import Config File Config File Status Firmware Picture 2 2 5 5 System maintenance interface e Network TCP IP Browse import Browse Upgrade In the TCP IP screen users can set IPv4 Address IPv4 Subnet Mask IPv4 Default Gateway IPv4 DNS Server and IPv4 mode When ticking Auto the device will obtain the IP address automatically After changing some parameters you need to click Save to save the corresponding settings See picture 2 2 5 6 Network TCPAP Port DONS Net Settings Physical Address C DHCP IPv4 Address IPv4 Subnet Mask IPv4 Default Gateway IPv4 DNS Server IPv6 Mode IPv6 Address IPv6 Subnet
38. rding scan click save to save the scanning path 4 Start and stop the pattern scan click start to start the pattern scan and click the stop key to stop the pattern scan See 2 2 2 6 5 Delete the pattern scan click delete key to delete the pattern scan Path1 2D ce 1 Presetl 4 D 2 Presetl 22 Picture 2 2 2 5 Sequence settings Start path Delete Stop path Lg Save record Start record Picture 2 2 2 6 Pattern settings e Operation methods for IR LED Enter the IR LED setting screen to set the power of the low beam lights between 1 10 amounts the power of high beam lights low beam lights compensation enable illumination and IR status setting See 2 2 2 7 PoJ m IR Near 10 v IR Far 10 v Sensitivity 4 v Mode Auto w Save Picture 2 2 2 7 IR LED Setting Screen Copyright Qvis 9 All documentation rights reserved 11 e Auto scanning setting Enter the auto scan screen to set scan speed left boundary right boundary start scan and to stop scan Auto scanning include 8 scanning paths See 2 2 2 7 Auto Scan1 Speed 50 D 0 GES Picture 2 2 2 8 Auto scans settings 1 Scanning speed from 1 100 the larger the gap between numbers the more evident the effect will be 2 To set left boundary and right boundary of the scan first make the camera move to a specified direction and then click the left boundary icon Move the camera to a right hand direction stop camera
39. rere re iiia 1 41 Special Features lA Ho eee s sss MI 2 Funcigg Introdusion Wl s eene annees nn 2 Sur Edel ff GE 2 1 4 All Weather Outdoor Design ccccccccsseeeeeeeeeeeeecaeeeeceeeeeeeeeeeseseceeeeessaeaseeeeeesessnanneess 2 1 5 Preset Position Set Up and Call Up 3 IN Scan E e A aum We 3 ed Cl 9995 EN sss EEN 3 de8 Suen mg un 3 1 9 Technical Parameters eeeeeeeeeee cerea nnn nonne nnn D E a 4 1 10 OSD Menu Operation 4 Om WK 989 EH cw 4 d Web Browser Operation Guide 2289 fe s s MR 6 2 1 COMTWDNESBENELOnS N REA Lise eee nnns 6 GE eier ll ET ee 6 2 1 2 Network parameters 228 EI P ess 6 22 Web LOGIN sec AM E M eee 8 2289 Login WE EA E a 8 2 2 2 Download playing Component sessi nennen nennen nnn nn 8 Amo ee TTT 12 224 Lon erger snot CENE RS MD 13 2 2 5 Configuratigngffeeeeee m A AM 14 zw Parameter Configuration J2B 9 aaaeeeaei eenen 14 22 5 2 SyElmn EE EEN MMM ceed 5 2 2489 Network ee eese tte erdMEE 7 c E 17 2 2 5 4 Audio Video mf Ee VEA um ree 23 2 2 5 5 l lmage o ME m 25 2 24899 Safety TT Meo BERI mm 29 Copyright Qvis 9 All documentation rights reserved 3 OSD M
40. s reserved SOFT LIMIT MAIN MENU LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT DOME SETTINGS IR LED WIPER IDLE ALARM ADVANCED OTHERS BACK ADVANCED AUX SOFT LIMIT DOME SPEED POWER ON ACTION TILT ANGLE BACK LIMIT SETTING SOFT LIMIT ON LEFT LIMIT RIGHT LIMIT LIMIT DELETE The user can set up the soft limit to define the left and right boundaries for the pan movement 1 SOFT LIMIT Move the cursor here and click IRIS to enter Click the up or down button to select ON or OFF to enable or disable this function LEFT LIMIT Move the cursor here and click IRIS to enter to control the PAN movement of the dome to a defined position for the left limit Click IRIS to confirm RIGHT LIMIT Move the cursor here and click IRIS to enter to control the PAN movement of the dome to a defined position for the right limit Click IRIS to confirm LIMIT DELETE Move the cursor here and click IRIS to delete all the settings 45 3 8 DOME SPEED MAIN MENU To set the dome speed the user can enter this menu to set up in degree angle per second LANGUAGE ENGLISH INFORMATION Move the cursor to DOME SPEED and click DOME SETTINGS IRIS to enter to select the dome speed when bh EK doing the pan movement RESTART FACTORY DEFAULT Move the cursor to BACK EXIT and click IRIS 4 EXIT to run the command of BACK or EXIT DOME SETTINGS
41. ser can click either modify delete and clear to manage IP address See picture 2 2 5 31 Copyright Qvis 9 All documentation rights reserved 31 cl Parameter Configuration User RTSP Authentication Anonymous Visit IP Address Filter Local Configuration System Enable IP Address Filter Network IP Address Filter Type Black List Audio Video Image IP Address Filter Safety Event Serial Number IP Storage Picture 2 2 5 31 IP address Filter e Event Motion detection Area setting hold down left mouse key and drag it across the live preview footage window then release mouse left key this will finish drawing the area When user finishes drawing the area arming schedule and linkage methods can be set Click Clear all to clear drawing area Tick the enable motion detection box will start the IP camera motion detection function See picture 2 2 5 32 Sensitivity 0 100 settable Parameter Configuration Motion Detection Video Tampering Exception Enable Motion Detection Area Setting 2004 01 19 15 13 21 le Event Picture 2 2 5 32 Motion Detection Arming schedule will show the current motion detection arming time Copyright Qvis 9 All documentation rights reserved 32 Click edit to edit the arming schedule for the whole week or for selected days within the week User can also set start time and end times for four specific periods per day see picture 2 2 5 33
42. ss www 3322 0rg Domain test Port 80 User Name test Password esce Password Confirm Picture 2 2 5 8 DDNS configuration screen Copyright Qvis 9 All documentation rights reserved 18 e Network PPPoE Tick Enable PPPoE this enables the PPPoE function Input the PPPoE user name and PPPoE password click Save and restart camera Camera will now gain a public IP address After modifying the related parameters need to click Save to save settings See picture 2 2 6 9 xxx ae TCPAP Pott DONS PPPoE FTP UPnP Email PortMapping WIFI C Enable PPPoE Network Dynamic IP User Name Picture 2 2 5 9 PPPoE configuration Note When PPPoE configuration is enabled the default gateway becomes invalid when the parameters in network settings are modified you Will need to reboot device e Network FTP By setting up the FTP parameter the user will then be able to upload snapshot files to an FTP server See picture 2 2 5 10 Server address and Port number need to correspond to the ones on FTP server Directory structure is where you can set the save path of file Options include Save in the root directory Save in the parent directory Save in the child directory When choosing parent director you can include Use device name Use device number Use device IP address Child directory includes Use camera name Use camera number After modifying re
43. ter to select ON or OFF to enable or disable this function 54 3 17 RESTART MAIN MENU LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT WARNING ARE YOU SURE OK CANCEL Copyright Qvis 9 All documentation rights reserved TRACKING SCENE SET Here the user can set up the scene the dome will go back to when the camera has finished auto tracking Move the cursor here and click IRIS to enter Move the dome to the wanted scene and click IRIS to confirm DELETE Move the cursor here and click IRIS to delete the return scene RETURN DELAY To set up the time that dome will waiting to return to this scene RESTART The dome allows the user to reset its settings remotely under this menu Move the cursor here and click IRIS to enter Select OK or CANCEL to continue the reset or cancel the reset 55 3 18 FACTORY DEFAULTS MAIN MENU LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT WARNING ARE YOU SURE CANCEL Copyright Qvis 9 All documentation rights reserved FACTORY DEFAULT will allow the user to recover all the original factory default settings Move the cursor here and click IRIS to enter Select OK or CANCEL to continue the reset or cancel the reset 56 For more information about our IP Cameras and other available cameras NVHs amp accessories please
44. the cursor here and click IRIS to delete start the current sequence 52 3 15 PATTERN TOUR MAIN MENU LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT MOTION PRESET SCAN SEQUENCE PATTERN AUTO TRACKING BACK PATTERN PATTERN NO 1 TITLE PATTERN 1 START SET DELETE BACK The dome supports 4 pattern tours and each pattern provides a maximum of 10 Minutes of 500 commands Please check the following steps to set up a pattern 1 Copyright Qvis 9 All documentation rights reserved PATTERN NO Move the cursor here and click IRIS to enter the setup of Pattern Number Click the up or down button to select a pattern number 14 and click IRIS to confirm TITLE Move the cursor here and click IRIS to enter the setup of Pattern Title Check the detailed above in DOME TITLE settings SET Move the cursor here and click IRIS to enter Click the dome up down left right make the zoom in out and click IRIS to save the pattern tour START Move the cursor here and click IRIS to start the current pattern tour DELETE Move the cursor here and click IRIS to delete the current pattern tour 53 3 16 AUTO TRACKING MAIN MENU LANGUAGE ENGLISH INFORMATION DOME SETTINGS MOTION RESTART FACTORY DEFAULT EXIT MOTION PRESET SCAN SEQUENCE PATTERN AUTO TRACKING BACK EXIT AUTO TRACKING SENSITIVITY MID TARGET MID
45. the following details Sender sender address SMTP server SMTP port Tick start SSL or authentication user name password amp password confirm receiver and receiver address see picture 2 2 5 12 Email detail settings are shown in Picture 2 2 5 12 TGCPAP Port DDNS Sardar Network sender Sender Address SMTP Server SMTP Port Start SS1 Lee Authentication Usar Hame Password Password Confirm Receiver Receiver 0 Name Receiver 0 Address Recetver 1 Name Recever 1 Address Recelver 2 Name Recermer a Address Receiver 3 Name Receiver 3 Address Parameter PPPoE FTP 3 nn Email PortMapping WIFI tesi testisqq com simip OO Cam 25 tesi Te 21 Testiaqa com Picture 2 2 5 12 Email Image quality Frame Rate Instruction Lowest low lower medium highest higher Max Bitrate Depending on resolution Video Encoding According to user s needs T J According to user s needs Frame Interval Frame between former and back 1 100 Sheet 2 2 5 13 Video configuration instruction Copyright Qvis 9 All documentation rights reserved 21 e Network Port Mapping Tick Enable Port Mapping to automatically open port see picture 2 2 5 14 J Parameter Configuration TCPAP Pott DDNS PPPoE FTP UPnP Email Port Mapping C Enable Port Mapping Network Port mapping mode fio Video Port Type External Port image HTTP 80 RTSP 554 Event HTTPS 443 Sheet 2 2 5 14 audio settings e Ne
46. tion In the preview screen you can control the camera s streamed video which includes control over video recording snapshot intercom and the on off of the sound The size of the image can be adjusted according to the needs of the user to set its original size we have 4 3 16 9 or Self adaptation mode Preview code stream can be set as main stream sub stream See 2 2 2 3 e Operation methods for preset position 1 Find the preset section to the interface and it will show the current preset camera position 2 Setting a preset position select a preset position number and then operate direction of the camera using the directional controls 3 When the camera scene moves to the place you want to set then click the save key to save this preset position 4 Call the preset position click call and the set preset position can be called 5 Delete preset position click delete can clear the information of preset position 6 Special function preset position this kind of preset position can be called but it cannot be modified or deleted Copyright Qvis 9 All documentation rights reserved 10 e Operation methods for pattern scanning 1 Enter the pattern scan screen it will show the current pattern scan path oee 2 2 2 5 2 Start recording the scanning click start to record the pattern scan and the start using the camera directional controls to adjust the movement of the camera 3 Stop reco
47. tion Or Alarm E Motion And Alarm E Other Picture 2 2 5 36 Record schedule Copyright Qvis All documentation rights reserved 35 Edit Schedule A Mon Tues Wed Thur Fri Sat Sun OQ AI Day Section Time Period Start Time End Time Video Type 1 00 00 i 00 00 amp Timing v 2 00 00 i 00 00 amp Timing v 3 00 00 LG 00 00 amp Timing v 4 00 00 i 00 00 i Timing v 5 00 00 t 00 00 i Timing v 6 00 00 i 00 00 amp Timing v 7 00 00 t amp 00 00 i Timing Mh 8 00 00 t 00 00 i Timing v Copy to Week Select All Mon v Tues v Wed v Thur v Fri v Sat v Sun OK Cancel v Picture 2 2 5 37 Edit Schedule e Storage Storage Management otorage management menu is used to view the status and the capacity of the storage medium You can also carry out format operations on the storage medium Select the inserted TF card click Format to format the TF card See picture 2 2 3 38 HDD No shows the serial number of the storage medium Capacity shows the total capacity of a storage medium Free space shows remaining space of a storage medium Status shows the current status of the storage medium Format formats operation of the storage medium Record Schedule Storage Management Capture HDD Device List LI HDD No Capacity Free space status Tyne Property Progress Quota Max Picture Capacity 0MB Free Size for Picture DME Storage Video Surplus Capacity OME Free Size for Record
48. twork WIFI To enable WIFI connection you need to input WIFI connection WIFI parameters in to the relevant input fields Click Save to save setup oee picture 2 2 5 15 Live View Configuration Log PlayBack e TCPAP Port DONS PPPOE FTP UP np rg Era Pott Mapping Wireless network list Network No 5510 Operating Mode Sate Mode Channel test 1 test 1 1 test O8 Wi Fi SSIO test Network mode e Manage Ad Hoc Sate Mode WEP wv Encryption type TKIP v Key 1123466 NIC configuration parameters DHCP IPy4 Address 102 168 1 200 Test IPv4 Subnet Mask IPv4 Defaut Gateway Mulcast Address DN server configuration Preferred ONS server Anter ate ONS server Picture 2 2 5 15 WIFI settings Copyright Qvis 9 All documentation rights reserved Signal Strengt Seve 22 2 2 5 4 Audio Video e Audio Video Video Enter Video setting screen these options will allow the user to set camera stream type resolution bitrate type etc See picture 2 2 6 16 video settings detailed information see picture 2 2 5 17 d Para Video Audio ROI Stream Type Main Stream Normal v Video Type Audio Video Resolution 1920 1080 v Bitrate Type Variable v Video Quality Medium v Frame Rate 25 v Max Bitrate 4096 Kbps Video Encoding H 264 v Frame Interval 50 Picture 2 2 5 16 Video settings Frame between former and back 1 100 Picture 2 2 5 17 Video settings instructions e Audio
49. visit our website WWW adata co uk Alternatively scan this QR code with your smart phone to be directed instantly to our website oF m Copyright Qvis All documentation rights reserved 57
50. y 192 168 0 1 WEB port 8000 2 1 2 Network parameters You will need to connect the camera to a PC with Windows installed in order to check the camera s IP network parameters and to see if there is a successful connection Make sure the default factory IP details of the camera is within the network parameters of the user computer and also within the same network address segment The IP address of the camera and the LAN cannot be the same otherwise they will interfere with each other causing the equipment to not operate correctly together Connect the camera to the PC by firstly connecting an Ethernet cable between the camera and the PC s NET port and then provide power to the camera using the power adapter To test whether it has been successfully connected use the PING order within the cmd console Copyright Qvis 9 All documentation rights reserved 6 To find the cmd console in Windows firstly search for cmd on your computer the icon for it should look like this Once loaded the format of the command needs to be ping 192 168 0 99 If the camera is correctly setup and connected the cmd console should display this pinging 192 168 0 99 with 32 bytes of data Reply from 192 168 0 99 bytes 32 time 1ms TTL 64 Reply from 192 168 0 99 bytes 32 time 1ms TTL 64 Reply from 192 168 0 99 bytes 32 time lt l1ms TTL 64 Reply from 192 168 0 99 bytes 32 time 1ms TTL 64 ing statistics for 192 168 0 9
Download Pdf Manuals
Related Search