Solar LED security light with motion sensor and built
Contents
1. 26 ft 8 m FIG 3 The motion detector s infrared beams radiate outward in a fan like pattern Prior to mounting keep in mind that the motion sensor is more sensitive to motion moving perpendicular to the direction that the sensor is facing and less sensitive to motion that moves directly towards or away from the sensor See Fig 4 FIG 4 ASSEMBLY INSTALLATION MOUNTING THE SOLAR LED SECURITY LIGHT Follow the instructions in Fig 5 to mount the Solar LED security light 01 4 Place the Solar LED security light mounting bracket 02 in the location where you have chosen to install it Using a pencil or felt tip marker mark the placement of the three holes of the Solar LED security light mounting bracket 02 on the wall Then remove the mounting bracket 02 Choose a drill bit appropriate for the surface you are drilling into For example for stucco or cement use a masonry drill bit Select a bit size slightly smaller in diameter than the wall anchor 05 and drill three pilot holes where you marked 4 Gently hammer three wall anchors 05 into the three holes Line up the three holes on the mounting bracket 02 with the three wall anchors 05 and fasten using the three long screws 04 6 Mount the Solar LED security light 01 to the mounting bracket 02 using the mounting fixture screw 07 7 Tighten the mounting fixture screw 07 sec2. Model Home 6RHAS100LGR ADVANCES Solar LED security light with motion sensor and built in video camera IMPORTANT READ THIS ENTIRE MANUAL TO BECOME FAMILIAR WITH THE PRODUCT BEFORE USE FOR HOUSEHOLD USE ONLY INTRODUCTION It is usually difficult for the average person to even consider installing an outdoor lighting and surveillance camera system until now This Solar LED security light with motion sensor and built in video camera is designed to economically provide safety and security for your home And best of all you can install it yourself by carefully following this manual OVERVIEW During the day the solar panel collects light and maintains a charge in the battery At night the energy stored in the battery is used to power the LED light To avoid wasting energy the Solar LED security light remains in standby mode until body movement is detected by the built in motion sensor The Solar LED security light will activate at night whenever movement is detected within 16 5 26 ft 5 8 m During activation the blue pilot light behind the lens will flash to indicate a trigger the light will illuminate for 15 seconds and the video camera will record for 10 seconds Please note that the run time is dependent on how much sunlight the security light has collected during the day FEATURES AND SPECIFICATIONS detachable solar panel camera baie OFF ON Heni
3. The Solar LED security light camera can be swiveled up and down and left to right according to your needs To adjust it first loosen the dial counterclockwise then adjust the head Then tighten the dial clockwise See Fig 8 FIG 8 CHARGING THE BATTERY There are two ways to charge the battery by solar panel or by AC adapter Please note that charging by AC adapter requires the purchase of equipment not provided BY SOLAR PANEL Unscrew the waterproof cover and remove it Make sure that the ON OFF switch is in OFF position then replace the waterproof cover and screw back on tightly Before using the Solar LED security light for the first time leave the ON OFF switch in the OFF position for at least four 4 sunny days with the solar panel placed in direct sunlight This will ensure that the battery has a full charge prior to motion sensor adjustment and normal operation BY AC ADAPTOR NOT INCLUDED Unscrew the waterproof cover and remove it Make sure that the ON OFF switch is in OFF position Plug a 4 5 5V 500mA AC adapter into the DC Jack then into a power outlet See Fig 9 FIG 9 ac adapter not included SETTING UP AND OPERATING THE SECURITY LIGHT SETTING THE WORKING MODE After the initial battery charging remove the waterproof cover if necessary to adjust the working mode See Fig 10 OFF Position for delivery or for long periods of non use Position for initial charge before first use ON D
4. using a USB cable not supplied Alternately you can also remove the card and insert it into a card reader or a digital camera When connected the SD card will show as a removable hard drive You can use Windows Media Player or other software to navigate to the DCIM 100DSCIM folder and see your captured videos You can copy videos to your PC delete them from the SD card or edit them VIEWING VIDEOS DIRECTLY ON YOUR PC Oo Unscrew the waterproof cover on the security light FIG 11 2 Connect one end of a USB cable not included to the USB port on the Solar LED security light and then the other end to a USB port on your computer The SD card will now show on your computer as a removable drive See Fig 11 not included VIEWING VIDEOS THROUGH A CARD READER OR DIGITAL CAMERA Unscrew the waterproof cover on the security light FIG 12 2 Push in the SD memory card and it will spring out Gi m Carefully remove the card from SD card socket Put the SD card in a card reader or digital camera With either device connected to your PC in the usual way the SD card will appear as a removable hard drive See Fig 12 ae Ss card reader not included SD memory card slot PRECAUTIONS WHEN USING A SD CARD The SD memory card is equipped with a write protect switch FIG 13 Setting the switch to LOCK protects the existing data by prohib
5. waterproof compartment switch mounting blue pilot light cover lot for SD USB port memory card Front View Back View e Detachable crystal solar panel 4 3 x 3 2 109 mm x 82 mm with 6 5 ft 2 m cable allows panel to be mounted away from the light e 1 x 3 7V 1800 mAh Lithium rechargeable battery included e Two ways to re charge battery 1 Recharge by solar cell through DC Jack 2 Recharge directly by AC Adapter not included e 10 x 50Lum Super Bright LEDs no light bulbs to replace e Passive infrared sensor has effective viewing angle of 100 and effective viewing distance of 16 4 26 25 ft 5 8 m e Records 10 second video 10 frames per second at 480 x 640 pixels e Built in SD card slot for SD memory card e 1GB SD card included stores 150 of the latest 10 second videos e SD card specification FAT e Video contains audio plus auto date and time stamp e Video format JPEG AVI File e Auto light sensor e Sensitivity control e Protection Class IPX4 PARTS LIST TOOLS REQUIRED AFTER UN PACKING YOUR NEW SOLAR LED SECURITY LIGHT CHECK THE PRODUCT FOR DAMAGE AND MAKE SURE THAT YOU HAVE ALL PARTS IN THE PARTS LIST IF YOU HAVE ANY PROBLEMS WITH THIS PRODUCT OR IF THERE ARE MISSING OR DAMAGED PARTS PLEASE CALL CUSTOMER SERVICE TOLL FREE 1 800 459 4409 MONDAY FRIDAY 8 30AM 5PM EST DO NOT RETURN THE PRODUCT TO THE STORE BEFORE CALLING THE TOLL FREE NUMBER Joey 7 v Solar LED security light mountin
6. TRICITY OR ELECTRICAL INTERFERENCE AVOID USING OR STORING THE CARD IN DIRECT SUNLIGHT OR WHERE IT MAY BE EXPOSED TO RAPID CHANGES IN TEMPERATURE OR TO CONDENSATION WHEN USING AN SD MEMORY CARD WITH A SLOW RECORDING SPEED RECORDING MAY STOP WHILE YOU ARE TAKING MOVIES OR SHOOTING AND PLAYBACK MAY TAKE A LONG TIME EVEN WHEN THERE IS ADEQUATE SPACE IN THE MEMORY BE SURE TO FORMAT AN SD MEMORY CARD THAT IS UNUSED OR HAS BEEN USED ON ANOTHER CAMERA PLEASE NOTE THAT FORMATTING THE SD MEMORY CARD WILL NOT NECESSARILY DELETE THE DATA SO THAT IT CANNOT BE RECOVERED USING OFF THE SHELF DATA RECOVERY SOFTWARE THERE ARE OFF THE SHELF SECURE DATA DELETION SOFTWARE PROGRAMS AVAILABLE THAT WILL COMPLETELY DELETE THE DATA IF YOU ARE GOING TO DISCARD GIVE AWAY OR SELL YOUR SD MEMORY CARD YOU SHOULD ENSURE THAT THE DATA ON THE CARD IS COMPLETELY DELETED OR THE CARD ITSELF IS DESTROYED TROUBLESHOOTING Light will NOT switch on when there is movement in the detection area Ensure that the power switch on the main body has been turned to the ON position Ensure that the motion sensor has been positioned to face movement Ensure that the battery has been fully charged in direct sunlight for four 4 sunny days Check to see that the solar cell charge panel is facing south so that it receives direct sunlight for most of the day enabling the battery to fully charge Check to see that the solar panel is not near night time light sources suc
7. aytime camera on Nighttime both camera and light on When you are finished adjusting the working mode replace the waterproof cover making sure to tighten the screws carefully The Solar LED security light is ready for use FIG 10 OFF ON switch slot for SD USB port memory card SETTING THE DATE AND TIME Follow these instructions to set the date and time that will be stamped on each video clip A Connect the Solar LED security light to your PC with a USB cable not included The SD card will now show as a removable hard drive 2 Open the Date amp Time set up folder Cut and paste the time txt file to the root directory Note a root directory is the first or topmost directory in the folder hierarchy For example if your computer assigns the SD card to be the E Drive then the root directory is E 4 Enter the current date and time in the time txt file Now the date and time will show on each video clip VIDEO RECORDING AND PLAYBACK Video clips are recorded onto the SD card that is inserted in the SD slot See Fig 10 on the previous page One 1 GB SD card is provided which can record approximately 150 video clips When the memory card is full it will start overwriting the first recordings to ensure that you always have the latest videos available VIEWING VIDEOS VIA PC OR DIGITAL CAMERA To view videos you can connect directly to the SD card of the Solar LED security light by
8. ery in full direct sunlight for four 4 sunny days 5 Remove the waterproof cover again and slide the ON OFF switch to the ON position 6 Reattach the waterproof cover The unit is now ready for use FIG 14 FOO J O SS ee 9 2 agoe g F OFF ON r FF waterproof eli ia e OFF ON waterproof cover switch 5 cover G 3 7V 1800mah 2 4 A3 7v 1800 mAh Lithium battery Lithium battery ATTENTION The old battery must be recycled or disposed of properly For additional information regarding disposal contact your local solid waste authority RECYCLING This product bears the selective sorting symbol for waste electrical and electronic equipment WEEE For further information on how to recycle or dismantle this product in order to minimize its impact on the environment please contact your local or regional authorities Electronic products not included in the selective sorting process are potentially dangerous for the EE environment and human heath due to the presence of hazardous substances WARRANTY This product is warranted to be free from defect in materials and workmanship under residential use for a period of one year from date of purchase If the unit should fail to operate correctly please call customer service at 1 800 459 4409 Monday Friday 8 30 am 5 00 pm EST or contact u
9. g bracket 02 Solar panel mounting bracket 03 5 x Long screws 04 TOOLS REQUIRED U gt Drill with Screwdriver 6 mm drill bit 5 x Wall anchors 05 pues 2 x Short screws 06 l a 1 x Mounting Aye fixture screw 07 Hammer Utility knife Pencil THIS PRODUCT IS DESIGNED TO ILLUMINATE AND TO MAKE VIDEO RECORDINGS IT WILL NOT PREVENT THE COMMISSION OF ANY ACT LEGAL OR ILLEGAL THE MANUFACTURER ASSUMES NO LIABILITY FOR ANY DAMAGE TO PROPERTY INJURY TO PERSON OR DEATH REMOVE DIRT OR STAINS WITH A SOFT CLOTH DAMPENED WITH WATER OR NEUTRAL DETERGENT USE A SOFT LENS CLOTH FOR CLEANING THE LENS AVOID TOUCHING THE LENS WITH FINGERS KEEP THE SECURITY LIGHT IN A DRY AND COOL DUST FREE ENVIRONMENT OR CONTAINER WHEN IT IS NOT BEING USED THIS SECURITY LIGHT IS DESIGNED TO BE WEATHER RESISTANT NEVER ATTEMPT TO IMMERSE THE UNIT IN WATER OR ANY OTHER LIQUID THIS WILL DAMAGE THE UNIT AND VOID THE WARRANTY THIS PRODUCT IS A PRECISION ELECTRONIC DEVICE DO NOT ATTEMPT TO SERVICE IT YOURSELF AS OPENING OR REMOVING COVERS MAY EXPOSE YOU TO THE DANGER OF ELECTRIC SHOCK OR OTHER RISKS YOU COULD ALSO DAMAGE THE UNIT AND WILL VOID THE WARRANTY LOCATION CHOICE FOR INSTALLATION CHOOSING A LOCATION FOR YOUR SOLAR LED SECURITY LIGHT This Solar LED security light can be mounted on any FIG 1 solid surface such as a wall The detachable solar panel is attached to a 6 5 ft 2 m power cord and can be m
10. h as street lights Light switches on for no apparent reason Moving trees traffic pets or birds may be getting in the area of detection This may be unavoidable however the sensor could be redirected to a height where this is less likely to occur If there are reflective objects in the detection area such as windows water or white walls you may need to redirect or possibly reposition the motion sensor Test the motion sensor by covering it completely with cardboard and waiting several minutes to make sure it does not detect motion If the light still switches on please contact us for further assistance Light quickly flashes on and off The battery charge may be low Turn the ON OFF switch to the OFF position and charge the battery for four 4 sunny days ensuring the solar cell charge panel has been placed in direct sunlight Light is not as bright as normal Battery charge may be low Turn the ON OFF switch to the OFF position and charge the battery for four 4 sunny days ensuring the solar cell charge panel has been placed in direct sunlight BATTERY REPLACEMENT Follow the instructions in Fig 14 to replace the battery a Unscrew the waterproof cover 2 Make sure the ON OFF switch is in the OFF position G Carefully remove the old battery from its compartment 4 Replace with a new 1800 mAh Lithium rechargeable battery of same or greater capacity Replace the waterproof cover and recharge the new batt
11. iting recording of new data deletion of existing data or i formatting of the card A prompt will pop up on the PC screen r when the card is write protected See Fig 13 SD J terminal write protect switch rear front WARNING THE DATA ON THE SD MEMORY CARE SHOULD BE TAKEN WHEN REMOVING THE SD MEMORY CARD CARD MAY BE DELETED IN THE IMMEDIATELY AFTER USING THE CAMERA AS THE CARD MAY BE HOT FOLLOWING CIRCUMSTANCES WE DO NOT ACCEPT ANY DO NOT REMOVE THE SD MEMORY CARD OR TURN THE CAMERA OFF WHILE LIABILITY FOR DATA THAT IS DATA IS BEING SAVED TO THE CARD OR WHEN THE CARD IS CONNECTED DELETED TO A COMPUTER WITH A USB CABLE AS THIS MAY CAUSE THE DATA TO BE LOST OR THE CARD TO BE DAMAGED 1 When the SD card is mishandled by the user DO NOT BEND THE SD MEMORY CARD OR SUBJECT IT TO VIOLENT IMPACT When the SD card is exposed KEEP IT AWAY FROM WATER AND STORE AWAY FROM HIGH TEMPERATURES to static electricity or electrical DO NOT REMOVE THE SD MEMORY CARD DURING FORMATTING AS THIS interference MAY DAMAGE THE CARD AND RENDER IT UNUSABLE When the SD card has not been used for a long time IF IT IS NOT USED FOR A LONG TIME THE DATA ON THE CARD MAY BECOME When the card is ejected or UNREADABLE BE SURE TO REGULARLY MAKE A BACKUP OF IMPORTANT the battery is removed while DATA ON A COMPUTER the data on the card is being AVOID USING OR STORING THE CARD WHERE IT MAY BE EXPOSED TO STATIC recorded or accessed ELEC
12. ounted vertically or horizontally onto a solid surface that receives direct sunlight such as a roof or wall You can adjust the angle of the solar cell by moving the angle adjustment on the solar panel to a different locking position See Fig 1 NOTE It is recommended that you mount the Solar LED security light about 6 5 ft 2 m above the ground for optimum performance Do not mount the fixture less than 4 ft 1 2 m above the ground For optimum sun exposure and longer light output place the solar panel when attached to the Solar LED security light in a position that receives at least 6 8 hours of direct sunlight per day Ideally the solar panel should face south Placing the solar panel in a shaded location will not allow the battery to charge fully and will reduce the number of hours of operation per evening In choosing a location for your Solar LED security light ensure that the solar panel is not placed near night time light sources such as porch or street lighting See Fig 2 at FIG 2 When deciding where to mount the light keep in mind that the passive infrared sensor PIR operates by detecting movement and heat When the temperature of the moving object and its surrounding area are close in value it may reduce the PIR s sensitivity The sensor will normally pick up the movement of a person up to 16 5 26 ft 5 8 m away when the outside temperature is 82 F 28 C or less See Fig 3
13. s through our website at www qualitycraft com Proof of purchase is required for all claims The company s sole obligation is to repair or replace the unit This warranty is void if in the opinion of Quality Craft the unit has been tampered with altered taken apart misused or damaged WARRANTY CLAIM PROCEDURE If a claimable defect occurs please fill out a claim form through our website at www qualitycraft com or contact our customer service department at 1 800 459 4409 Before you make your claim call please make sure you have 1 The description of the product 2 Proof of sale 3 Details regarding the defect 4 Name and address of the owner and installer Claims must be filled out in writing and returned within six 6 months of appearance of defect Failure to comply with this stipulation will make the warranty null and void We reserve the right to a thirty day 30 delay following receipt of claim in which to inspect the product We assume no responsibility for labor costs or removing replacing a previously installed product or transportation or return of a product Imported by QualityCraft Laval Quebec Canada H7C 0A5 1 800 459 4409 www qualitycraft com Made in China
14. urely FIG 5 pumo 04 05 07 MOUNTING THE SOLAR PANEL If you are mounting the solar panel separate FIG 6 from the camera light body see Fig 6 for how to separate the solar panel from the Solar LED security light 01 Unscrew the waterproof cover on the Solar LED security light and remove Unscrew the solar panel Carefully pull out the cord knob and detach the solar panel waterproof cover Follow the instructions in Fig 7 to mount the solar panel 1 Place the solar panel mounting bracket 03 in the location where you have chosen to install it Using a pencil or felt tip marker mark the placement of the two holes of the solar panel mounting bracket 03 on the wall Then remove the mounting bracket 03 If two wall anchors 05 are required use a drill bit suitable for the type of surface you are drilling and drill two pilot holes 4 Gently hammer the two wall anchors 05 into the two holes 5 Securely fasten the solar panel mounting bracket 03 to the wall with two long screws 04 6 Attach the solar panel to the solar panel mounting bracket 03 with the two short screws 06 7 Securely tighten the two short screws 06 FIG 7 V S 03 he 04 05 ms 06 ae oj 04 solar panel V ADJUSTING THE ANGLE OF THE SOLAR LED SECURITY LIGHT
Download Pdf Manuals
Related Search