5804BDV User`s Manual
Contents
1. K3636V1 5 00 5804BDV ADEMCO two way WwRELESS KEY with VOICE STATUS USER GUIDE About the 5804BDV The 5804BDV is a four button remote control for your alarm system It can send a command to the alarm system such as to arm or disarm as well as receive system status Two LEDs and a speaker indicate system status The 5804BDV is typically used for arming disarming and home automation Check with your installer to understand which functions the buttons have been assigned on your unit Operating the Buttons Activating a Function To activate a function press and hold the appropriate button down until the yellow LED flashes and then release it Requesting System Status You can check system status before arming or disarming your system Check your system status by momentarily pressing and releasing any button The yellow LED will flash after you release the button After a second or two the 5804BDV will display the system status through the LEDs and speaker see the System Status Indications Table below If the 5804BDV does not receive system status from the panel for approximately 5 seconds it will shut itself down It will also shut itself down if you do not press a button within 5 seconds of receiving a status update System Status Indications Table e uEDconaiion speeen syoemsns PYetow en Fasting racat RF transmission non encrypted FYetow tet Fishing racates RF transmission encrypted Red amp Green Alternately I2. n Enter House ID Mode Flashing In Enable or Disable High Security encrypted Mode _ Enable or Disable High In Enable or Disable High Security encrypted Mode _ encrypted Mode In In Set Volume Level Mode ssid In Set Volume Level Mode ssid Level Mode Low Battery Low Battery Condition System Disarmed Not Ready To Arm System Not Ready Zones Faulted A C Button Pair B D Button Pair Multiple Button Operations fa The 5804BDV should not be used WARNING for silent panic operation The 5804BDV can generate the same responses as keypad panic key pairs of and 1 by depressing A C and B D button pairs respectively You must depress the button pair for at least 2 seconds for the 5804BDV to recognize the button pair command These button pairs allow you to activate panic fire and medical alarms depending on control panel programming Adjusting the Volume Level To enter the Volume Level mode press and hold down the A B and D buttons at the same time until the unit s red and green LEDs flash alternately If no button is pressed within 5 seconds the unit will automatically shut down and no change to the volume level is made You press the A button for low volume level the B button for mid volume level and the C button for maximum volume level You will hear a tone for the selected volume You then press the D button to accept the sound level you have selected Note tha
3. stant activation of a programmed button may reduce battery life in a given installation If the button unit is used infrequently activate it regularly once per week to confirm operation A button type transmitter will report a low battery condition to the alarm control when a low battery status is detected ALARM DEVICE MANUFACTURING CO A DB MI O O DIVISION OF PITTWAY CORPORATION 165 Eileen Way Syosset NY 11791 COPYRIGHT 2000 PITTWAY CORPORATION K3636V1 5 00
4. t volume level affects the life of the battery Use low volume for maximum battery life Low Battery Indication When the unit goes into a Low Battery condition the yellow LED will not flash when a button is pressed Change both batteries immediately To Replace the Batteries Remove the screw from the back case Remove case back by using the blade of a small screwdriver to pry open Place batteries as shown on diagram Use CR2430 or DL2430Lithium batteries only Battery Close the case by snapping case front and back together Replace the screw to secure the case ag ON Improperly installing the batteries will cause damage to the batteries Removing or Inserting the Unit from a Belt Clip LIMITATIONS STATEMENT Signals sent by wireless transmitters may be blocked or reflected by metal objects before they reach the alarm receiver Even if the signal path has been recently checked during a weekly test blockage can occur if a metal object somehow blocks the signal path Wireless button type transmitters that have visual and audible indications of status must be used to confirm that the desired action such as arming has occurred after pressing a function button on any of these transmitters Be sure to listen for appropriate audible and visual indications that such action has occurred Otherwise you could inadvertently leave yourself or your premises unprotected External factors such as humidity high or low temperatures or con
Download Pdf Manuals
Related Search