User`s Guide 600A True RMS AC/DC Clamp Meter
Contents
1. before operating the meter Repair or replace any damage before use Use great care when making measurements if the voltages are greater than 25VAC rms or 35VDC These voltages are considered a shock hazard Remove the battery if the meter is to be stored for long periods Always discharge capacitors and remove power from the device under test before performing Diode Resistance or Continuity tests Voltage checks on electrical outlets can be difficult and misleading because of the uncertainty of connection to the recessed electrical contacts Other means should be used to ensure that the terminals are not live If the equipment is used in a manner not specified by the manufacturer the protection provided by the equipment may be impaired Input Limits Function Maximum Input AAC ADC 600A V DC V AC 600V DC AC Resistance Capacitance Diode Test 250V DC AC Temperature 60V DC 24V AC 38389 V2 6 10 03 Meter Description Current clamp Data Hold button 1 Peak Hold button Mode select button ZERO button LCD display COM input jack Clamp trigger Rotary Function switch 0 V G CAP TEMP jack O OCS OP Or e a O AK WD N 1 AC alternating current and DC direct currrent 2 Minus sign 3 4000 count 0 to 3999 measurement reading 4 AutoRange mode 5 Peak Hold mode 6 Diode test mode AUTO PEAK gt HOLD ZERO BAT 1 DC i GD lt gt es KOH 7 Audible Continui2. on an annual basis to ensure calibration integrity gt ES Tech Support Hotlines 781 890 7440 ext 200 support extech com www extech com Copyright 2002 Extech Instruments Corporation All rights reserved including the right of reproduction in whole or in part in any form 11 38389 V2 6 10 03
3. six month limited warranty applies on sensors and cables If it should become necessary to return the instrument for service during or beyond the warranty period contact the Customer Service Department at 781 890 7440 ext 210 for authorization or visit our website at www extech com click on Contact Extech and go to Service Department to request an RA number A Return Authorization RA number must be issued before any product is returned to Extech The sender is responsible for shipping charges freight insurance and proper packaging to prevent damage in transit This warranty does not apply to defects resulting from action of the user such as misuse improper wiring operation outside of specification improper maintenance or repair or unauthorized modification Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct indirect incidental or consequential damages Extech s total liability is limited to repair or replacement of the product The warranty set forth above is inclusive and no other warranty whether written or oral is expressed or implied Repair and Calibration Services Extech offers complete repair and calibration services for all Extech products For periodic calibration NIST certification or repair of any Extech product call customer service for details on services available Extech recommends that calibration be performed
4. to the 600 or 400A range If the range of the measured is not known select the higher range first then move to the lower range if necessary 2 Select AC or DC with the AC DC button Press the zero button to zero the meter in the DCA mode only 3 Press the trigger to open jaw Fully enclose one conductor to be measured 4 The clamp meter LCD will display the reading AC DC Voltage Measurements 1 Insert the black test lead into the negative COM terminal and the red test lead into the positive V terminal 2 Set the function switch to the V position 3 Select AC or DC with the AC DC button 4 Connect the test leads in parallel to the circuit under test 5 Read the voltage measurement on the LCD display 7 38389 V2 6 10 03 Resistance and Continuity Measurements 1 w 5 6 Insert the black test lead into the negative COM terminal and the red test lead into the positive terminal Set the function switch to the t Q CAP position Use the multifunction button to select resistance Touch the test probe tips across the circuit or component under test It is best to disconnect one side of the device under test so the rest of the circuit will not interfere with the resistance reading For Resistance tests read the resistance on the LCD display For Continuity tests if the resistance is lt 30Q a tone will sound Capacitance Measurements WARNING To avoid electric shock discharge the capacitor under tes
5. User s Guide EXTECH NSTRUMENTS 600A True RMS AC DC Clamp Meter Model 38389 Safety International Safety Symbols This symbol adjacent to another symbol or terminal indicates the user must refer to the manual for further information normal use hazardous voltages may be present Double insulation A This symbol adjacent to a terminal indicates that under SAFETY NOTES Do not exceed the maximum allowable input range of any function Do not apply voltage to meter when resistance function is selected Set the function switch OFF when the meter is not in use Remove the battery if meter is to be stored for longer than 60 days WARNINGS UL Set function switch to the appropriate position before measuring When measuring volts do not switch to current resistance modes Do not measure current on a circuit whose voltage exceeds 600V When changing ranges using the selector switch always disconnect the test leads from the circuit under test Do not exceed the maximum rated input limits A UL mark does not indicate that this product has been evaluated for the accuracy of its readings 2 38389 V2 6 10 03 CAUTIONS Improper use of this meter can cause damage shock injury or death Read and understand this user manual before operating the meter Always remove the test leads before replacing the battery or fuses Inspect the condition of the test leads and the meter itself for any damage
6. attery Indication Overrange Indication Measurements Rate Temperature sensor Input Impedance Display AC bandwidth AC response Operating Temperature Storage Temperature Relative Humidity Altitude Over voltage Battery Auto OFF Dimensions Weight Safety Open circuit voltage 1 5V DC typical Threshold lt 50Q Test current lt 1mA BAT is displayed 1 is displayed 2 per second nominal Type K thermocouple 7 8MQ VDC and VAC 3 3 4 digits 4000 counts LCD 50 60Hz AAC and VAC True rms AAC and VAC 14 to 122 F 10 to 50 C 14 to 140 F 30 to 60 C 90 0 C to 30 C 75 30 C to 40 C 45 40 C to 50 C Operating 3000m Storage 10 000m Category Il 600V 9V Battery After 15 minutes of inactivity 8x3 2x1 7 204x80x43mm 0 62 Ibs 281g For indoor use and in accordance with Overvoltage Category II Pollution Degree 2 Category Il includes local level appliance portable equipment etc with transient overvoltages less than Overvoltage Cat III 6 38389 V2 6 10 03 Operation NOTICES Read and understand all warning and precaution statements listed in the safety section of this operation manual prior to using this meter Set the function select switch to the OFF position when the meter is not in use AC DC Current Measurements WARNING Ensure that the test leads are disconnected from the meter before making current clamp measurements 1 Set the Function switch
7. n again to return to normal operation Peak Hold To hold the highest reading on the LCD press the peak hold button The peak hold button is located on the left side of the meter bottom button The meter reading will not change as readings change rather it will only display the highest reading encountered since the peak hold button was pressed Press the peak hold button again to return to normal operation 9 38389 V2 6 10 03 Maintenance WARNING To avoid electrical shock disconnect the meter from any circuit remove the test leads from the input terminals and turn OFF the meter before opening the case Do not operate with open case Cleaning and Storage Periodically wipe the case with a damp cloth and mild detergent do not use abrasives or solvents If the meter is not to be used for periods of longer than 60 days remove the battery and store it separately Battery Replacement 1 Remove the Phillips head screw that secures the battery door 2 Open the battery compartment 3 Replace the 9V battery 4 Replace and secure the door Temperature Probe Replacement The replacement bead wire probe with banana plug connectors is p n TP873 The use type k probes with a mini plug connector requires a mini plug to banana plug converter p n 872000 10 38389 V2 6 10 03 Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date of shipment a
8. t before measuring ti Set the function switch to the HF Q CAP Position Press the multifunction button to select the capacitance function Insert the black test lead banana plug into the negative COM jack and the red test lead banana plug into the positive jack Touch the test probe tips across the part under test Read the capacitance in the display The display will indicate the proper decimal point and value 8 38389 V2 6 10 03 Temperature Measurements WARNING To avoid electric shock disconnect both test probes from any source of voltage before making a temperature measurement 1 Set the function switch to TEMP 2 Insert the Temperature Probe into the negative COM and the positive jacks making sure to observe the correct polarity 3 Touch the Temperature Probe head to the part whose temperature you wish to measure Keep the probe touching the part under test until the reading stabilizes about 30 seconds 4 Read the temperature in the display The digital reading will indicate the proper decimal point and value WARNING To avoid electric shock be sure the thermocouple has been removed before changing to another measurement function Data Hold To freeze the LCD meter reading press the data hold button The data hold button is located on the left side of the meter top button While data hold is active the DH display icon appears on the LCD Press the data hold butto
9. ty 3 POLI RN pr 8 Data Hold mode 9 ZERO Relative mode 10 Low Battery icon 11 Units of measure list 4 38389 V2 6 10 03 Specifications Function Range amp Resolution Accuracy of reading DC Current 400 0 ADC 0 to 70A 2 5 0 6A 70 to 300A 3 0 0 3A 300 to 400A _ 3 5 0 3A 600 ADC Oto 150A 2 5 4A 151 to 350A 3 0 4A 351 to 600A 4 0 6A AC Current 400 0 AAC 0 to 70A 3 0 0 6A 70 to 300A 3 5 0 3A 300 to 400A _ 3 5 0 6A 600 AAC Oto 150A 3 0 4A 151 to 350A 3 5 5A 351 to 600A 4 0 8A DC Voltage 400 0 mVDC 0 5 5 digits 4 000 VDC 40 00 VDC 1 2 3 digits 400 0 VDC 600 VDC 1 5 3 digits AC Voltage 4 000 VAC 1 0 5 digits 40 00 VAG 1 5 3 digits 600 VAC 2 0 4 digits Resistance 400 0Q 1 0 4 digits 4 000KQ 40 00KQ 1 5 2 digits 400 0KQ 4 000MQ 2 0 3 digits 40 00MQ 3 0 5 digits Temperature 4 to 1400 F 3 0 5 F 20 to 760 C 3 0 3 C 38389 V2 6 10 03 Function Range amp Resolution Accuracy of reading Capacitance 40 00 nF 5 0 7 digits 400 0 nF 4 000 uF 3 5 5 digits 40 00 uF 100 0 uF 5 0 5 digits Clamp size Opening 1 3 33mm approx Diode Test Test current of 0 3mA typical Continuity Check Low B
Download Pdf Manuals
Related Search