Base and Tag Instruction Manual _FLIPBOOK_small
Contents
1. Retain Instructions These safety and operating instructions should be retained for future reference The operator of this equipment should from time to time review the manufacturers website for any new or revised instructions warnings and safety information 3 Heed Warnings All warnings on the product and in the operating instructions should be read understood and adhered to 4 Follow all instructions 5 Do not expose BASE directly to water Do not place any part SOLOSHOT near any heat sources such as radiators heat registers ovens stoves or other apparatus including amplifiers that produce heat 7 Only use attachments and accessories specified or approved by the manufacturer of SOLOSHOT2 8 Unplug this apparatus during lightning storms or when unused for long periods of time 9 Refer all servicing to qualified service personnel approved by the manufacturer Servicing is required when the apparatus has been damaged in any way including power supply cord or plug damage liquids have een spilled into or around the BASE or CHARGER or objects have fallen into the apparatus the BASE or CHARGER has been exposed to rain or moisture does not operate normally or has been dropped 5 n Follow Instructions All operating and maintenance instructions should be followed Cleaning Clean BASE and TAG separately Clean BASE only with a dry cloth Unplug BASE from the wall outlet and completely detach CHARGER from BA2. 1 866 347 0869 info soloshot com DESIGNED amp BUILT IN THE USA
3. 4 times in rapid succession LEDs 1 3 will turn GREEN for 2 seconds before going back to their previous state indicating you have stored the E gt Tag Capture Centering Object Command For use when calibrating multiple Bases sold separately using a single Centering Object Centering Object in your Tag for use later in your session Use this stored Centering Point to calibrate a Base by pressing the BUTTON of the Tag until LED 1 turns GREEN after 7 seconds Continue pressing your Tag s BUTTON and also press the BUTTON on the Base that has been prepared for Press Four Times 4x to Capture Centering Object calibration meaning the Base is pointed at the shared Centering Object You may Press amp Hold for 7 Seconds capture a NEW Centering Object at any time by pressing the BUTTON 4 times to use Centering Object rapidly Capture Centering Object Command simplifies the set up of multiple Bases For best results select a centering object that is further away than the activity you will be filming 7 ADVANCED SETTINGS TAG Tag Highlight Command Same requirements as Record ON OFF Command You may tell your camera to immediately STOP and RESTART recording by 1 Pressing the Button or 2 Tapping the white surface of your Tag 3 times quickly 5 ae Press Once to Send LEDs 1 3 will flash GREEN before LED3 resumes blinking RED for record HIGHLIGHT Command command TIP Sending
4. set to Single mode LED4 GREEN meaning it only keeps track of a single Tag To set your Base to Multi Mode use quick presses of the BUTTON to cycle through the setting LEDs until LED4 is blinking Press the mode button once to turn LED4 indicating your Base is now in Multi Tag mode MULTI SYSTEMS Single Multi Settings Toggle to Multi Mode to track multiple Tags from the same Base GREEN Single Mode default RED Multi Mode B Extra Tags sold separately See Extra Tag Quick Start Guide to learn how to pair multiple Tags to the same Base Single Base to Multiple Tag MULTIPLE TAGS EZB Set Multi Tracking Mode When Multi Mode is on your Base will by default track the by LEDS being GREEN You can change this setting to Fastest Mode or Call Mode using the BUTTON closest Tag that is paired with the system by default as indicated only available in Multi Mode Use this setting to tell the Base when to switch between Tags GREEN Closest Tag Mode Base will follow the closest Tag RED Fastest Tag Mode Base will follow the fastest Tag ORANGE Follow Me Mode Allows a subject to call the Base by pressing their Tag s BUTTON or by triple tapping their Tag firmly tap the Tag three times in rapid succession MULTIPLE TAGS Select Multi Mode Record Setting Camera Controller ACCESSORY required Sold separately LED6 will be active when you have a came
5. sports fe Compare Surf and Turf Jump Detection versus Big Motocross Terrain Altitude and see what works best for you Set your Base up at the landing zone and capture Skydiving yourself as you swoop in Shoot as wide as possible Downhill Sports Requires Camera Controller Accessory Sold separately ADVANCED SETTINGS BASE Manually Offset Your Centering Position While in Surf amp Turf Mode your Base will automatically adjust its tilt to keep your feet on an imaginary line separating the bottom third and middle third of the screen and centered horizontally While in Big Altitude Mode your Base will automatically adjust its tilt to keep your Tag in the center of the screen However you can use the PAN and TILT arrows to manually offset your position on the screen For example a kite boarder might want to offset their position towards the bottom of the screen so that their kite is included in the shot ONLY ADJUST YOUR CENTERING AFTER YOU HAVE COMPLETED STEP 9 NOTE any vertical offsets you make will ONLY be present in the current tilt mode For example shifting your position while in Surf and Turf Mode will not effect your position in Big Altitude Mode and vice versa ADVANCED SETTINGS BASE FED Calibrating in Big Altitude Mode Use the POWER and MODE buttons on your Base to set LED1 to RED and perform Setup Steps 5 amp 8 with the following alterations Step 5 Use wider framin
6. 4 Mounting Screw 5 Accessory Release Button 6 K Lock Port 7 USB Ports Mini amp USB 2 0 side BASE 7 Power Button 8 Mode Button 9 Pairing Button 10 Pan Tilt Buttons 11 Mode LEDs 12 Antenna 13 Tripod Socket back side EQUIPMENT OVERVIEW EQUIPMENT OVERVIEW TAG 1 Charging Docking Z 9 Contact 2 Power Button 3 Pairing Button 4 Status LEDs 5 Top Surface EQUIPMENT OVERVIEW TRIPOD TOOL CHARGING CABLE CLIP ARM BAND LISTEN IMPORTANT You MUST read and understand the Cheat Sheet that came with your product so you understand BASIC set up pairing and calibration before attempting the advanced settings described in this manual SOLOSHOT is a robot It assumes that you have FOLLOWED THESE INSTRUCTIONS While robots FREE us from repetitive and time consuming tasks they do not replace HUMAN CREATIVITY So please enjoy your freedom and get creative ADVANCED SETTINGS BASE Using Advanced Settings SOLOSHOT offers a variety of Modes designed for various sports shooting styles and situations Each of the six LEDs on the back of the Base represents a Setting indicated by LED that can be toggled between different Modes indicated by LED color Cycle through the Setting LEDs by quickly pressing and releasing the 2 BUTTON The active Setting LED will flash Cycle through the various Modes within the active Setting by pressing the Murron The f
7. CHILDREN WARNING STRANGULATION HAZARD CONTAINS A LONG POWER CORD THAT MAY CAUSE STRANGULATION IF USED IMPROPERLY KEEP OUT OF REACH OF SMALL CHILDREN TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE SOLOSHOT BASE TO REDUCE THE RISK OF ELECTRICAL SHOCK AND TO PREVENT UNDESIRABLE INTERFERENCE ONLY USE THE RECOMMENDED ACCESSORIES COPYRIGHT WARNING Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws CAUTION Do not expose this product to excessive heat such as the inside of a car under direct sunlight fire etc To reduce the risk of electrical shock do not dis assemble the base station No user serviceable parts inside Refer servicing to qualified service personnel Warranty voided if unauthorized service is performed CAUTION Do not place more than a well balanced 5 lb load on the SOLOSHOT base CAUTION To prevent electric shock fully insert plug while charging on Contains li polymer battery Battery must be recycled or disposed properly Important Safety Instructions In these safety instructions the word product refers to SOLOSHOT including the BASE TAG and all of it s accessories 1 Read Instructions All safety and operating instructions should be read completely and understood completely before the product is operated 2
8. NGS BASE GREEN Wide Frame Mode Camera Controller automatically adjusts zoom AND tilt EIE Zoom Settings Only available when Camera Controller is connected to maintain a wide shot as the Tag moves closer to or farther away from the Base RED Medium Frame Camera Controller automatically adjusts zoom AND tilt to maintain a medium width shot as the Tag moves closer to or farther away from the Base MEDIUM ORANGE Tight Frame Mode Camera Controller automatically adjusts zoom AND tilt to maintain a tight shot as the Tag moves closer to or farther away from the Base NOTE The subject is less likely to stay centered in the frame as the shots get tighter Over aggressive zooming in some situations can cause the subject to periodically go out of the frame In Big Altitude Mode all of the zoom setting frame sizes are 50 larger than in the Surf amp Turf and Pan Only modes ADVANCED SETTINGS BASE Single Multi Settings Toggle to Multi Mode in order to track multiple Tags from the same Base B GREEN Single Mode default RED Multi Mode SEE PAGES 25 40 FOR DETAILED DESCRIPTION OF CREATING amp MANAGING MULTI SYSTEMS Single Base to Multiple Tags only available in Multi Mode Use this setting to tell the Base when to switch between Tags GREEN Closest Mode Base will follow 0 the closest Tag RED Fastest Mode Base will follow the fastest Tag ORANGE Follow Me Mode Allows a Tag
9. SE before cleaning Only use a clean dry cloth to clean e A the external surfaces of BASE Do no use liquid or aerosol cleaners on BASE Clean the TAG only by rinsing in fresh water The product should be cleaned only as recommended in this manual 2 Accessories Only use accessories recommended in this manual as all other accessories may be hazardous 3 Avoid magnetic or electric fields Do not use 50 05 2 close to TV transmitters portable communication devices or other sources of electric or magnetic radiation They may cause interference or permanent jamage to your SOLOSHOT2 4 Water and moisture ELECTRIC SHOCK HAZARD Do not expose BASE or CHARGER to wet environments The TAG is waterproof up to 10 ft but BASE and CHARGER are NOT waterproof or water resistant 5 The TYP60 0901500u Compact Power Adapter CHARGER should be operated only from the type of power source indicated on the marking label AC100 to 240V If you are not sure of the power supply in your ome consult your local power company ONLY USE CHARGER AS DESCRIBED IN THIS INSTRUCTION MANUAL 6 Power Cord Protection The power cord of the CHARGER should be routed such that it is NOT likely to be walked on or pinched by items placed upon or against it Pay particular attention to plugs and the point from which the cords exit the product 7 Objects and Liquid Entry Never push objects of any kind into or through openings of BASE or TAG as they may touch dangerous vol
10. TASOLOSHOTZ Important Usage Instructions This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This device meets the requirements for RF exposure to humans when worn on the upper arm or against the body In order to comply with FCC standards this device should not be used in any other application other than that described in this manual This device complies with Part 15 of the FCC rules Changes or modifications to the device not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment When the transmitter is worn on the body there may be increased risk of injury if the remote strikes a solid object or the ground The transmitter has been designed to be worn as an armband for use in surfing but for other sporting activities it may be preferable to be placed elsewhere such as on the outside of a helmet or attached to a vehicle if used in motor sports There is no one recommendation as it depends on the activity terrain aggressiveness of the activity and specific use By using SOLOSHOT user agrees to assume all risk and not hold Soloshot Inc liable for injuries or damages in any way NS WARNING CHOKING HAZARD CONTAINS SMALL PARTS KEEP OUT OF REACH OF
11. g since vertical tracking is less accurate Step 8 Walk for at least 100 150 steps prior to pairing with Base for best vertical tracking results NOTE If you calibrate in Surf amp Turf Mode you can toggle to Big Altitude Mode later but if you calibrate in Big Altitude Mode you should not switch to Surf amp Turf Mode because the Base will not track properly Go for a longer walkabout to improve tracking accuracy when using Base in Big Altitude Mode KEY TIP ADVANCED SETTINGS TAG Tag Record ON OFF Command By default your Tag broadcasts a record command as indicated by LED3 blinking RED You can tell your camera to go to standby by holding down the BUTTON for 2 seconds until LED3 blinks GREEN Remember RED record Your Base s tracking LED normally blinks GREEN like this blink blink blink blink blink blink When a Camera Controller is properly attached and your Base receives a record command the LED will switch to an extended single blink YOUR CAMERA WILL ONLY RESPOND TO THIS COMMAND IF 1 YOU ARE USING THE CAMERA CONTROLLER ACCESSORY 2 YOU ARE USING A SUPPORTED CAMERA 3 YOUR TAG IS IN RANGE Press and Hold to Toggle Recording ON OFF ADVANCED SETTINGS TAG ie Tag Hide Me Command LED3 will either blink RED camera recording or GREEN camera on standby when radio is ON You may turn OFF your Tag s radio at any time by quickly pressing the BUTTON twice LEDs 1 2 and 3 wil
12. highlight commands makes it easier to find specific moments when editing because they will be located at the end of a file TAG COMMAND SUMMARY BUTTON SUMMARY Press and hold until LED3 changes color Radio ON OFF Press twice to Toggle Follow Me Command Press Once Base must be in Multi Mode Follow Me Mode Highlight Command Press once or Tap White Surface 3 times Capture Centering Object Press four times Use Centering Object Press and hold until LED1 turns green Requires Camera Controller Accessory Sold separately NOTE All BUTTON presses are acknowledged by LEDs 1 2 and 3 turning GREEN while the button is held MULTI SYSTEMS BD Creating a Multi Device System You create a Unique System each time you pair a Base and Tag together by pressing their 8 BUTTONS simultaneously during setup and calibration You can add more Tags sold separately to this Unique System by pairing them to a Base or Tag that is already part of the system A new Base or Tag may be added to the system by FIRST pressing and holding the BUTTON of the device that is ALREADY part of the system and then pressing the 3 BUTTON on the device you wish to add NOTE You must set each Base to Multi Mode if you want that Base to follow multiple Tags TIP If you press the buttons in the wrong order you can correct the mistake by re pairing both to a device that is still part of the original sys
13. i Mode LED4 RED and pair the desired Tags to the System as described on page 27 29 FILTER 1 Identify a Centering Object that will be visible from all the camera locations you wish to set up Example Manhole Cover 2 Walk over to the shared Centering Object with your warm Tag TOP WHITE SIDE UP facing the sky and after completing the 50 100 step walkabout press the BUTTON 4 times as described on pg 22 LEDs 1 2 and 3 on your Tag will flash GREEN with each button press and remain GREEN for 2 seconds after the fourth button press indicating you have stored the Centering Object s location for later use 3 Set up each Base as described in Steps 1 5 of the Cheat Sheet Once each Base is set up you can either follow the Pairing amp Calibration procedure described in Step 4 below or setup and calibrate each Base one by one according to the steps outlined in the Cheat Sheet 4 Perform the standard 50 100 step walkabout with your warm Tag Press and hold the 3 BUTTON on your Tag towards the end of your walk and until LED1 turns GREEN Continue pressing the BUTTON and while holding your Tag above your Camera TOP WHITE SIDE UP facing the sky Press the BUTTON on your Base The LEDs on the Base will flash RED for a few seconds and LED3 on your Tag will blink RED Once pairing AND calibration are complete the Tracking LED on the Base will blink GREEN The Base will start tracking the Tag after you ha
14. ing and GREEN when fully charged Note the Base MUST also be plugged in to charge a Tag Slide the dock button down to release the Tag Your Tag will be 80 charged after 1 5 hours 80 after 2 5 hours 90 after 4 hours and 99 after 5 hours at KEYTIP which point the charging LED will turn GREEN WARNING Make sure the Tag and Accessory Port are clean dry and clear of all debris before connecting FIRMWARE UPDATE Check SOLOSHOT com for the latest SOLOSHOT2 Base firmware updates You will be provided with files named SOLOSHOT ss2 and 002 ss2 Copy those files to a standard USB drive Hold Button down then tap the Power button while holding down M Button to put the Base in Update Mode LED 1 will flash RED GREEN indicating the Base is ready for Firmware Update Insert USB into the standard USB socket on the side of the Base LED 1 will turn solid ORANGE LED 2 will blink RED GREEN then LED 1 and 2 will turn off and LED 3 will blink RED GREEN The Base will then return to Default Mode where LED 1 2 and 4 will be solid GREEN indicating the Base Update is complete NOTE If your Base will not accept the firmware try starting with an empty and recently formatted USB drive The USB drive must be a USB 2 0 drive black inside the connector Check SOLOSHOT com for the latest SOLOSHOT2 Base firmware updates You will be provided with files named 001 ss2 Copy those files to a standard USB drive Hold B
15. l briefly turn GREEN then LED1 and LED2 will turn solid RED camera recording or solid GREEN camera on standby Repeat this procedure to power your Tag s radio back ON Press Two Times to Toggle Radio ON OFF TIP Need a rest Toggle radio off to save battery while keeping the Tag warm amp paired Filming in Multi Mode Use Hide Me Mode to momentarily hide a Tag from the Base Simply toggle the radio back on to rejoin the action ADVANCED SETTINGS TAG Tag Multi Mode Follow Me Command Tell all Bases set to Multi Mode Follow pg 34 to follow your Tag by 1 Quickly pressing the BUTTON will NOT automatically start recording 2 Tapping the TOP WHITE SURFACE surface of your Tag three times quickly will automatically start recording Press Once to Call Base LEDs 1 2 and 3 will flash GREEN before LED3 returns back to blinking RED camera recording or GREEN camera standby Look towards the Base for the blinking GREEN Tracking LED to confirm the Base is now pointing at you To ensure that the camera is always recording when pointed at your Tag keep your Tag in record mode LED3 blinking RED or use the tripple tap to call the camera automatically starts recording TIP Use the Tap to Call method so you don t have to look at your Tag or the BUTTON ADVANCED SETTINGS TAG After walking about with your warm Tag proceed to the Centering Object and Press the BUTTON
16. lashing LED will change color as you cycle through the available Modes Try different combinations of Modes to see what works best for you Setting amp Mode Indicators Surf amp Turf Mode Ideal for sports involving a large generally level playing field like Surfing Park Skating amp Soccer RED Big Altitude Mode Great for sports with large altitude changes like Skydiving Snowboarding NOTE this mode is less accurate and therefore requires a wider frame to ensure most of the action is captured See page 18 to learn more ORANGE Pan Only Mode Great for filmmaking where panning alone has the desired cinematic effect Set the tilt manually and it will not change during use Suggested framing for Big Altitude Mode MANUAL ND FILTER MANUAL ND FILTER 3 15 16 GREEN Standard Mode default Base tracks Tag based on LED 1 setting RED Barrel Mode Base assumes lost communication with Tag epee arcing tog eetrelode is due to getting barreled and continues to track for 8 seconds or until communication with Tag is reestablished ORANGE Jump Detection Mode Designed for activities that include large jumps on a mostly level surface like kiteboarding BMX or motocross Jump Detection adds jump based tilt to Surf amp Turf mode so you can get tighter shots AND capture the jumps NOT available in Big Altitude Mode Suggested framing for Jump Detection Mode ADVANCED SETTI
17. ra controller attached to your Base AND your Base is set to Multi Mode on Your Base will be set to Cut Mode by default LED6 GREEN You can change this setting to Continuous Mode RED using the M BUTTON In Cut mode your Base will tell your camera to create a new file each time it switches between Tags to make editing and sharing easier See opposite page for details MULTI SYSTEMS Multi Mode Record Settings Only available if Multi Mode is ON and Camera Controller is connected to a supported camera GREEN Cut Mode creates a new video file each time the Base switches between Tags RED Continuous Mode continuous video recording when the Base switches between Tags See online User Guide for detailed information on Settings Multi Mode filming and other advanced features at www soloshot com MULTIPLE BASES Pair Extra Base s into your SOLOSHOT2 system to capture the action from multiple angles Extra Base s can be used to 1 Film one Tag from multiple perspectives 2 Film multiple subjects from multiple vantage points Requires Extra Tags sold separately Extra Bases sold separately SOLOSHOT2 Use the same Tag to calibrate each Base using the steps described in the Cheat Sheet of this Manual Each Base you calibrate will be in Single Mode by default LED4 GREEN and will be tracking the Tag used to calibrate it If you want each Base to track multiple Tags you must set each Base to Mult
18. system Press amp hold the BUTTON on an already calibrated Base before pressing the BUTTON on the Tag you would like to add to the system LEDs 1 2 and 3 on the Tag will briefly turn GREEN then RED Release the BUTTONs and LEDs 1 2 and 3 will turn GREEN for 2 seconds followed by LED3 blinking RED Press and Hold on Base and Extra Tag Tag warm or solid RED Tag not yet warm Repeat for additional Tags that you would like to add to the system LTI SYSTEMS TIP You can add and remove Tags and Bases or even combine whole systems from nearby users easily Example you are filming at a location for an hour and then your friend shows up with their own SOLOSHOT2Z sets up and films for a while Eventually you want to join systems so at least one of the Bases films both of you Pair one of the Tags to the other Each Base will continue to track the Tag it was originally paired to but one of the Bases will track BOTH tags if you place it in Multi Mode If you want the other Bases to also track BOTH Tags you must pair that Base into the system no need to recalibrate and set it to Multi Mode To pair that Base to the combined system press and hold the Button on either Tag and then press the Button of the Base All 4 items will now share the same system ID and both Bases can track both Tags when placed in Multi Mode Keep reading for details MULTIPLE TAGS Turn Multi Mode ON Your Base by default is
19. tage points or short out parts that could result in fire or electric shock or jamage to product Be careful not to spill liquids of any kind on BASE or CHARGER 8 Servicing Do not attempt to service any part of SOLOSHOT2 yourself as opening or removing covers or otherwise removing or altering any component SOLOSHOT2 may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Any attempt to access internal components will void manufacturers warranty 9 Rinse TAG CLIP and ARMBAND in fresh water after use in salt water TASOLOSHOT Safety and Handling Review full Safety and Handling information in the SOLOSHOT2 User Guide Videos and Tutorials For SOLOSHOT videos and tutorials visit www soloshot com videos Customer Service Call us at 1 866 347 0869 M F 9am 5pm CST or email us at info soloshot com Table of Contents Eguipme RENALES pgs 6 9 2 important Infommati OMincciicaisin ccna sts iiendirensinndinranravecctameccdnseapyedninty pgs 10 13 Settings Base pgs 14 23 6 Advanced pgs 24 29 Te Malti SYStOIMNS i aieenitemies pgs 30 45 8 Batteries amp Charging cccccsesesseseseeessesseesesesesseesssseessesassesesseeesseeensnsenseeens pgs 46 47 9 Firmware Updates pgs 48 49 EQUIPMENT OVERVIEW BASE 1 2 Tracking LED Tilt Drum 3 Accessory Port
20. tem MULTI SYSTEMS UNIQUE x_ 8x_ MULTI SYSTEM You fill in the blanks The possibilities are nearly endless Additional Bases and Tags sold separately Visit Soloshot com for more information MULTIPLE TAGS Add New Tags Using A Tag Press amp hold the BUTTON on the Tag that is already part of the system LEDs 1 2 and 3 will turn GREEN Then press the BUTTON on the Tag you wish to bring into the system The new Tag s LEDs will also briefly turn GREEN Once pairing is N complete LEDs 1 2 and 3 turn RED on both Tags Release both BUTTONS and LEDs 1 2 and 3 will turn GREEN for 2 seconds followed by LED3 blinking RED Tag warm or solid RED Tag not yet warm Press and Hold Existing Tag s 8 BUTTON first then Press New Tag s BUTTON Repeat for additional Tags you would like to add to the system MULTI SYSTEMS TIP You can pair multiple Tags together BEFORE calibrating ANY Bases This can come in handy at events where you want to pass out multiple Tags and keep one for calibrating your Base s TIP You DO NOT need to warm up or walkabout Tags before pairing them together but you MUST warm up and walkabout a Tag before using it to calibrate a Base TIP If you mistakingly press the buttons in the wrong order thereby creating a new system existing of just those two devices you can correct it by pairing those devices to a device that is still part of the original
21. to call the Base by pressing its BUTTON or by firmly tapping the white side of the Tag three 9 times in rapid succession SEE PAGES 25 40 FOR DETAILED DESCRIPTION OF CREATING amp MANAGING MULTI SYSTEMS ADVANCED SETTINGS BASE Multi Mode Record Settings Only available if Multi Mode is ON and Camera Controller is connected to a supported camera GREEN Cut Mode creates a new video file each time the Base switches between Tags RED Continuous Mode continuous video recording when the Base switches between Tags These Modes assume that all Tags being tracked are set to camera record If the Base switches to a Tag that is set to camera standby the camera will stop recording regardless of the Multi Mode Record Setting See page 19 for detailed instructions on how to toggle a Tag between record and standby SEE PAGES 25 40 FOR DETAILED DESCRIPTION OF CREATING amp MANAGING MULTI SYSTEMS LED 1 LED 2 LED 3 Tilt Specialty Zoom TIPS Settings ettings Settings Surfing Try Fastest or Follow Me in Multi Mode Field Sports Tag the ref and use Wide for an interesting perspective Compare Surf amp Turf Jump Detection versus Big Altitude and see what works best for you Kiteboarding Wa keboarding Set up a Base near a slider and set to Multi Mode closest pg 34 to film each Tagged rider as they hit it Zoom window sizes are 50 larger in Big Altitude Mode Try Tight or Medium for downhill
22. utton down then tap the Power button while holding down Button to put the Tag in Update Mode The Power button will flash RED GREEN indicating it is ready for Firmware Update Dock the Tag into the accessory port and power on the Base Insert USB drive into Base to begin the Tag Update LED 6 on the Base will flash RED GREEN while the Tag LEDs cycle RED GREEN during the Update LED 1 2 and 3 will turn solid GREEN then all will turn solid RED Once LED 2 and 3 turn off and LED 1 remains a Solid RED your Tag Update is complete NOTE Load all 3 files onto the USB drive and put both Base and Tag into update mode to update Base and Tag simultaneously FIRMWARE UPDATE 5 2 Safety and Handling Review full Safety and Handling information in the SOLOSHOT2 User Guide Videos and Tutorials For SOLOSHOT videos and tutorials visit www soloshot com videos Customer Service Call us at 1 866 347 0869 M F 9am 5pm CST or email us at info soloshot com 00000 SOLOSHOTupdates Follow us and share your SOLOSHOT experiences SOLOSHOT2 is designed and built in the USA by Soloshot Inc SOLOSHOT SOLOSHOT2 Robot Cameraman Automatic Cameraman Film Yourself Personal Cameraman Dedicated Cameraman and the SOLOSHOT logo are trademarks of Soloshot Inc 2014 Soloshot Inc All rights reserved US AND INTERNATIONAL PATENTS PENDING TSOLOSHOTZ SOLOSHOT Inc 2540 Boardwalk Street San Antonio TX 78217 www SOLOSHOT com
23. ve moved about 10 ft away from the Base YOU DO NOT HAVE TO RETURN TO THE CENTERING OBJECT STEP 9 5 You may set up your next Base using either the standard method of the Stored Shared Centering Object TIP You can switch between standard and Shared Centering Object Base calibration as you see fit Just press and hold the Tag BUTTON whenever you want to calibrate a base using the Shared Centering Object CHARGING Charge the Base using the USB to Mini charging cable provided by plugging the Mini end into the corresponding socket on the SOLOSHOT2 Base and the USB end into a standard USB wall adaptor not provided The charging LED will be RED while charging and GREEN when charging is complete Charging from a computer will take up to 3x longer than charging from wall power 4 hours 90 after 5 hours and 99 after 8 hours at KEYTIP which point the charging LED will turn GREEN Your Base will be 50 charged after 3 hours 80 after WARNING 46 Make sure SOLOSHOT socket cable connectors and wall charger are all dry 46 free from debris and undamaged before connecting system to wall power CHARGING While holding the Tag at a 45 degree angle dock the Tag into the Base by connecting the depressions on the top of the Tag into the hooks at the top of the accessory port and then bringing the Tag toward the port until the release button clicks The LED above the Tag s POWER BUTTON will turn RED when charg
Download Pdf Manuals
Related Search