Layout 2
Contents
1. USER MANUAL esp www espuk com Contents EZ TAG2 1 x Security Torx Key 10 x Tags and Back Plate 4 x Screws and raw plugs 1 x Marking out template Equipment required for controlling one door 12 volt DC power supply 2 amp minimum EV BPS Lock Magnetic EVML 250 Yale type keep 12 volt lock enter D Push to exit button EVEXIT Green break glass emergency release EVEBG Note for use with Magnetic lock only Functions of the EZ TAG2 The EZ TAG2 can control up to two doors by use of Tags or pin numbers Selectable Pin number length 2 3 4 5 and 6 digits per zone Programmable door open time 00 to 99 seconds Two locations zone 1 zone 2 are available for programming Tags and Pin numbers 1000 Tags or Pins can be programmed for zone 1 10 Tags or Pins can be programmed for zone 2 Two volt free change over relays one per door Door closed function contact required 2 push to exit button inputs one per zone Programmable volt free change over relay for door bell function Programmable rear tamper Internal buzzer for tamper monitoring automatic cut off after 1 minute Sighting Of The EZ TAG2 The EZ TAG2 must not be located within 2 meters of any reader keypad type devices The EZ TAG2 must not be sited back to back with other reader keypad type devices Site the EZ TAG2 within easy access to the door doors to be controlled Recommended mounting height 1 2m Fitting Using the template mark and drill2. green programming LED top left of keypad will illuminate Note if this location already has a pin number or Tag programmed the LED will turn red To delete this location press the star key twice The LED will now turn green Enter the pin number required a conformation bleep will be heard If further pin numbers are to be programmed select the next available location number xxx Programming one Tag to Zone 1 Note Do not have Tags in your hand or close by when pressing keys Zone 1 has 1000 locations available from 000 to 999 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Enter the location you want to programme the Tag to in a 3 digit format xxx The green programming LED top left of keypad will illuminate Note if this location already has a pin number or Tag programmed the LED will turn red To delete this location press the star key twice The LED will now turn green Pick up one Tag only and present it to the bottom of the reader EZ TAG and remove 2 bleeps will be heard If further Tags are to be programmed select a the next available location number xxx Programming a group of Tags to Zone 1 Note Do not have Tags in your hand or close by when pressing keys Zone 1 has 1000 locations available from 000 to 999 Enter programming mode All tags to be programed as a group must have consecutive numbers A Long bleep will be heard and the green power L
3. ED will turn orange Press the key then the 9 key the power LED will start to flash Press the O key then the 1 key the unit will bleep once Enter the number of the first available location in the range of 000 to 999 Now enter in a 3 digit format how many tags you want to programme xxx into the system present the lowest number tag to the reader EZ TAG A and remove Alternatively enter the 8 digit number of the lowest number Tag from the group to be programmed into the keypad To confirm the programming has been successful 2 bleeps will be heard Setting the Unlock Time for Zone 1 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key then the 1 key the orange LED will start to flash Enter the time in seconds for the unlock time from 00 to 99 seconds Zone 2 programming Programming A User Pin number to Zone 2 Note Zone 2 has 10 locations available 00 09 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 4 key The orange LED will start to flash Enter the vacant location number you want to programme the pin number in to xx The green programming LED top left of keypad will illuminate Note if this location already has a pin number or Tag programmed the LED will turn red To delete this location press the star key twice The LED will now turn green Enter the new pin number required a conformati
4. ble the door Bell function Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 2 key the orange LED will start to flash Press the O key followed by the 1 key The door bell function is now off How to reset a lost programming pin number Note this will set the programming Pin back to its default factory setting of 1234 and leave all other settings intact Remove power to the keypad reader for 10 seconds Apply power and press the key within 3 seconds Technical Specification DC input 12 24volts AC input 12 24volts Standby current 80ma Operating current without lock 110ma Working temperature 20c to 50c Reader frequency 125Hz Tag reading distance 5cm IP rating 65 Dimension 152 x 45 x 25mm Technical Support 01527 515145 Elite Security Products Telephone 01527 515150 Unit 7 Target Park Shawbank Rd S Technical Support 01527 515145 Lakeside Redditch B98 8YN email info espuk com www espuk com
5. ions for entering pin or Tags zone 1 and zone 2 Zone 1 has 1000 locations available 000 999 Zone 2 has 10 locations available 00 09 Programme pin numbers and tags Select the lock release time 00 99 seconds How to escape programming mode Note if no keys are press within 30 seconds the unit will drop out of programming mode How to enter and exit programme mode To enter programme mode enter the 4 digit pin number twice default pin 1234 To exit programme mode press the key How to set the length of the pin numbers to be used Enter programming mode by entering the 4 digit pin number twice default pin 1234 A Long bleep will be heard and the green power LED will turn orange Press the key followed by 9 key the orange LED will now flash Press 04 a long bleep will be heard Enter the length of the pin number you require 2 3 4 5 or 6 If the length is the same as already programmed you will get a conformation bleep If you have changed the length you will get 7 bleeps to say it has now been changed Note Any pin numbers or Tags programmed into the system will be deleted if the pin length is change Zone 1 programming Programming a User Pin number to Zone 1 Note Zone 1 has 1000 locations available from 000 to 999 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Enter the vacant location you want to programme the pin number in using a 3 digit format xxx The
6. lete all pin numbers and Tag data Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press key followed by the 8 key the orange LED will start to flash Press the 8 key twice 7 conformation bleeps will sound How to load factory default settings Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 8 key the orange LED will start to flash Press the 9 key twice One bleep will sound and the System will automatically come out of programming mode How to Disable the rear tamper Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 6 key the orange LED will start to flash Press the O key followed by the 1 key The rear tamer is now off How to Enable the rear tamper Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 6 key the orange LED will start to flash Press the O key followed by the 2 key The rear tamer is now on How to Enable the door Bell function Note If two doors are being controlled the bell function can not be used Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 2 key the orange LED will start to flash Press the O key followed by the 2 key The door bell function is now on How to Disa
7. on bleep will be heard If further pin numbers are to be programmed select the next available location number xx Programming one Tag to Zone 2 Note Do not have Tags in your hand or close by when pressing keys Zone 2 has 10 locations available 00 09 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press key then 4 the orange LED will start to flash Enter the location you want to programme the first Tag in to xx The green programming LED top left of keypad will illuminate Note if this location already has a pin number or Tag programmed the LED will turn red To delete this location press the star key twice The LED will now turn green Pick up one Tag only and present to the bottom of the reader EZ TAG and remove 2 bleeps will be heard If further Tags are to be programmed select a the next available location number xx Setting the Unlock Time for Zone 2 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key then the 5 key the power LED will start to flash Enter the time in seconds for the unlock time from 00 to 99 seconds How to Change the Programming Pin Number Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press key followed by the 3 key the orange LED will start to flash Enter the new programming pin twice A conformation bleep will be heard How to de
8. the fixing and cable entry holes Remove security screw from the underside of the keypad reader and remove back plate Fit and secure the back plate in its final position See Fig 1 Feed the cable from the keypad reader though the centre hole of the back plate Clip the top of keypad reader onto the back plate and secure using the security fixing screw located on the underside of the keypad reader Make all wiring connections and connect 12 volts DC to the keypad reader The green power LED will now be illuminated on the front of the keypad reader Screws Screw raw plugs Wiring Diagram and connections Fr 5 Red power DC input 12V 24V Black power J AC input 12V 24V Brown door status detecting Orange push to exit button 1 Yellow push to exit button 2 A Green GND Blue NO 2 Purple COM 2 SN Gray NC 2 O White NO 1 Pink COM 1 m NCI Aqua NC 1 L Black white 485 9 noi Sine Brown white 485 Shielded ground Red A input 12V 24V Black 0 AC input 12V 24V Brown Door contact Orange Button1 Yellow Button2 Green a GND Additional power supply for lock PAM are Door lock Black White 485 Brown White 485 Shielded ground 9 Brief details of programming Access of programming mode Selecting the length of the pin number to be used 2 3 4 5 and 6 digits There are two locat
Download Pdf Manuals
Related Search