M4x VoIP Blade Quick Start Guide
Contents
1. Port Rev B 2011 Raven Electronics Corporation 4655 Longley Lane Reno NV 89502 Main 775 858 2400 Sales Press 2 Technical Support Press3 Fax 775 858 2410 4 Configuring the M4x VoIP Module 9 Be sure to enable the session and press Submit Click on the Raven VolP on the system components 10 The session highlighted will be lit green as shown above window and the Port Status box will appear as shown in when the connection is established and working Figure 3 As with the Analog 4 Wire Module you may change the name Figure 3 Press settings and a larger box will appear with various tabs to choose from On this first tab labeled Description Figure 6 is where the Raven VoIP description can be changed to whatever the user or programmer would prefer Status Indicators Next press on the tab labeled Interface Settings as shown 1 To see the status of the VoIP Link click on the next to in Figure 4 This is where the local IP Addressing Raven VoIP on the system component window parameters are set for this Blade It is recommended to use a Static IP Address the default Press the Set 2 Click on the first VoIP Port and second if set up button when finished 3 This shows an example of the Raven VoIP Port 1 Receiving RCV and Raven VoIP Port 2 Transmitting XMT a VoIP stream Shown here with a Green Light lit next to VoIP RCV on the P2. led settings It is recommended to use the defaults for the RTP Real Time Protocol RX Port and TX Port 5 Click the check box Enabled to enable the bridge Raven Electronics Corporation 4655 Longley Lane Reno NV 89502 Main 775 858 2400 Sales Press 2 Technical Support Press 3 Fax 775 858 2410
3. n CD drive for each port installed in the M4x Blade Please note the pin i for clarity We recommend selecting Easy Install when prompted ONRET 1S Groupen 16r Garity 12345678 Follow the on screen prompts to complete the installation Note E Lead is PTT M Lead is COR Refer to the M4x User Manual included on the software disk for more detailed installation instructions especially if this version of software will be installed over a prior version of software Powering Up the M4x Blade WWW RAVENCOMM COM Connect the Power Cable into the AC Power Adapter MODULE 476 150 4 WIRE INTERFACE MODULE 476 151 4 WIRE INTERFACE MODULE 476 777 VOIP 2 Connect the AC Power Adapter to your AC power source rH Day meee Day WI Ly yy bem Lawa e g 3 pronged grounded wall outlet The AC Power ia inp ia a a Adapter can be connected to a 100 to 240 VAC 50 60 Hz mg SEO yg FHL pmo FMD Og jeD yg JO pyg JHE PIN 4 Jar PIN 4 Yan PIN 4 Jar PIN 4 Yar PIN 4 ii PIN 4 Jw im 0 5A source PIN 5 PIN 5 PIN 5 PIN 5 PIN 5 PIN 5 PIN 7 PIN 7 3 Connect the DC plug from the AC Power Adapter into the ma TD maf ma FED fpg hE pmo Hms pyg eo DC jack on the rear of the M4x Blade as shown in Figure 1 yo f l O ZY Thank you for choosing a Raven Electronics M4x Blade for your Communication needs where we are the idea shop committed to solving engineering problems and exceeding Figure 1 expectations DC Jack USB
4. ort 1 status screen and a Red Light lit next to VoIP XMT on the Port 2 status screen This shows the status of the VoIP connection and that communication is occurring Figure 4 Figure 7 VoIP Type is the next Tab to click as shown in Figure 5 This allows the user to choose different modes of operation Configuring a Bridge Most applications use Multi Point Unicast the default 1 Configure the M4x Analog 4 Wire Module s before configuring a Bridge 2 The M4x Blade allows multiple bridge configurations to be created on one blade 3 Click System Bridging on the right side of the screen 4 Drag various ports from the system components panel and Figure 5 drop them onto the Port Name boxes in the Bridge Now go to the Unicast Setup tab as shown in Figure 6 Configuration pop up box This is where the VoIP Configuration takes place amp ifBroadcastis NOT checked the associated Position the mouse over a Port an Analog Port previously bridge group will be full conference configured on the system components window Drag the Port into the screen above Repeat to include the Ports required to be backhauled If DITMF Bridge Group is enabled the members of the bridge are now able to be cross patched dynamically as remote users dial using DTMF Set the IP Address to match the host endpoint to enabled devices communicate with located under Peer l Please refer to the M4x User Manual for more detai
5. wWww ravencomm com Raven Electronics Corporation Specialized Communication Solutions 1968 M4x VoIP Blade Quick Start Guide Thank you for purchasing the M4x Blade LED Indicators There are seventeen LED indicators on the front panel of the M4x Blade as shown in Figure 2 There are two LEDs per Port The first LED is Red default is When unpacking your M4x Blade confirm the following items were received with your shipment Software CD XMT Output The second LED is Green default is RCV This CD also includes the User Manual Input AC Power Supply Adapter There is a Power On LED which is also Green to let the user 120 240 VAC 12 VDC 2 5 Amp regulated know the M4x Blade is powered on Note on units powered from a DC source this item will not be included Power Cord M4Communication System ry Port Note on units powered from a DC source this item will not be included USB Cable If any of these items are missing please contact Sales at 775 858 2400 press 2 Figure 2 For more details regarding how the LEDs can be set to indicate PTT E Lead or COR M Lead please refer to the M4x User Installing The M4x Software Manual Note Install this software before plugging in the M4x Blade Uninstall old M4x Software before installing a new version M4x Port Pin Outs 2 Install the software by inserting the CD into the computer s On top of the M4x Blade there is a label with pin out informatio
Download Pdf Manuals
Related Search