Metasys N2 OPTION OPC-G11S-MN2 for Fuji FRENIC5000G11S
Contents
1. WY WY Whitt Charge lamp 2 to 4 Loosen two screws M 4 at a and remove the top cover Loosen two screws M 3 at b and detach the keypad panel For the 30kW 40HP and above inverters the keypad panel can be detached if the front cover is removed and the screws loosened at b 1 Reassemble the top cover push in the option unit and secure it with two screws M 3 at Secure the keypad panel to the option unit with two screws at b Connect the ground cable to the PE terminal of the option unit HMS INDUSTRIAL NETWORKS AB USER MANUAL Revision 1 01 2000 11 06 3 2 Installation Checklist After installation and wiring check the following items 1 The wiring is correct 2 No loose wires or screws remain inside the Inverter 3 The screws and terminals are all tight 4 There are no loose threads of wires at terminals that may contact other terminals 5 The switch positions on the Anybus S module JP6 on the conversion board are suitable for the use purpose Do not change the JP4 the conversion board 6 Inverter parameters such as H30 027 028 030 to 038 are set correctly H30 Link Active Inactive 027 and 028 for RAS HMS INDUSTRIAL NETWORKS AB 7 USER MANUAL Revision 1 01 2000 11 06 4 Metasys 2 option card OPC G11S MN2 The OPC G11S PDP option card gives an instant connection between Fuji 6115 drives GE Fuji AF 300G112. 7 Operating the drive via Metasys 2 LS HMS INDUSTRIAL NETWORKS AB 3 USER MANUAL Revision 1 01 2000 11 06 1 Applicable inverters Inverter type FRENIC5000G11S P11S AF 300G11 P11 Compatible Inverter The last two digits of the model number should be 1 or later Model number Example 6KG1123X1B1 GE Fuji version Minimum inverter to 22 EN version 508000 and after ROM version It is impossible to use version prior number to 508000 inverter Japanese standard JE Cannot be used and CN version UX and GE Fuji version 508000 and after It is impossible to use version prior to S08200 inverter 30 kW 40HP and EN Japanese standard 07602 and after above JN JE AN CN UX It is impossible to use versions of 00000 to 07601 and Fuji version NOTE This product can only be used for Inverters with ROM version numbers greater than or egual to the versions shown above And in the case of installing this option in the G11 P11 inverter that is a Japanese standard JN JE version please contact Fuji Electric or its distributors Check the ROM number of your Inverter as follows using the inverter keypad a Check that the Inverter Operation monitor Operation mode screen is displayed b Press the PRG key of the Inverter once c Select the 5 MAINTENANC with the cursor and press the FUNC DATA key d Press the down cursor key
3. and Metasys N2 network The option board will perform as an integrated part of the G11S drive and gives the user access to all relevant parameters as well as control status signals needed to control the drive The OPC G11S MN2 option card communicates according to the etasys N2 standard from Johnson Control This means that it can communicate with all masters that comply with this standard but it does not necessarily mean that all services available in the etasys N2 standard are supported In a control system the 115 2 will act as a slave that can be read and written to from Metasys 2 master It will not initiate communication to other nodes it will only respond to incoming telegrams 5 Introduction to Metasys N2 etaSys N2 is a fieldbus system from the Johnson Controls company More than 10 000 systems are installed around the world in colleges and universities hospitals commercial offices factories government facilities and on military bases M etaSys N2 is mainly a fieldbus for building and automation industry 5 1 Technical features of Metasys N2 e Physical media EIA RS 485 twisted pair cable e Baud rate 9 6 kbps fixed e Maximum number of nodes 255 e Bus topology Master Slave communication The figure below gives an overview of a Metasys N2 network HMS INDUSTRIAL NETWORKS AB 8 USER MANUAL Revision 1 01 2000 11 06 6 OPC G11S MN2 Overview These sections contain all necessary info
4. to increment the display at the MAINTENANC screen Finally the ROM number is shown in the maintenance information as indicated by the display INV HXxxxxx or 5 The maintenance and inspection items are similar to the Inverter unit for detail refer to the Inverter Instruction M anual HMS INDUSTRIAL NETWORKS AB 4 USER MANUAL Revision 1 01 2000 11 06 2 Receiving Inspection Confirm the following items upon receipt 1 The model number matches your purchase order Check the model number printed on the circuit board Model 115 MN2 me TYPE 2 gt Metasys N2 INTERFACE OPTION INVERTER TYPE G115 gt FRENIC5000G11S P11S SERIES amp AF 300 G11 P11 SERIES 2 Inspection for damage during transportation Report damage to transportation carrier HMS INDUSTRIAL NETWORKS AB 5 USER MANUAL Revision 1 01 2000 11 06 3 Installation 3 1 Installation Method Please follow the installation procedure described as follows Please install or detach the option after turning off the input power supply of the inverter and confirming the charge lamp CHARGE or CRG is gone out The shape the dimensions and the position of the charge lamp of the inverter are different by each capacity keypad keypad Top cover YP b Option unit b 1 Inverter unit YA X s PE Line Inverter unit
5. USER MANUAL Revision 1 01 2000 11 06 USER MANUAL Metasys N2 OPTION OPC G11S MN2 for Fuji FRENIC5000G11S P11S amp GE Fuji AF 300G11 P11 DOC NO SIM 4124 001 HMS INDUSTRIAL NETWORKS AB 1 USER MANUAL Revision 1 01 2000 11 06 Revision Notes Document 00 01 03 Revision 0 10 Created by Jonas Akerlund JAK 00 01 10 Revision 0 11 Added Point list JAK 00 01 21 Revision 0 12 Updated Table 1 with terminal block pins JAK 00 02 01 Revision 0 13 Update of 6 3 indication LED 5 00 05 015 Revision 0 90 Update of 6 1 6 3 DSUB connection picture added 00 05 19 Revision 0 91 Update Table2 00 08 02 Revision 1 00 Document released 00 11 06 Revision 1 01 Added section 6 2 4 Preface The data and illustrations found in this document are not binding We reserve the right to modify our products in line with our policy of continuous product development The information in this appendix is subject to change without notice and should not be considered as a commitment by HM S INDUSTRIAL NETWORKS HMS INDUSTRIAL NETWORKS AB assumes no responsibility for any errors that may appear in this document The product and technology described in this document is patent pending in the following countries USA Canada Japan Belgium Denmark Finland France Greece Ireland Italy Luxemburg Monaco Netherlands Portugal Switzerland Liechtenstein Spain United Kingdom Sweden Germany and Austria Any Bus is a registered tr
6. ademark of HM S INDUSTRIAL NETWORKS AB All other trademarks are the property of their respective holders Related documents Document Author FRENIC5000G115 P115 INSTRUCTION MANUAL Fuji Electric INR Si47 0554 E HMS INDUSTRIAL NETWORKS AB 2 USER MANUAL Revision 1 01 2000 11 06 Table of Contents 1 Applicable inverters suzuzununzuna 2 RECEIVING Inspection 3 Installation AA AA nl Eee ee aO 3 1 WAstallation Mito aa 6 322 Installation CHECKS 7 4 Metasys N2 option 115 2 8 5 Introduction to M etasys 2 5 1 Technical features of 8 6 115 2 Overview ia aa aa AA Aa Ta Pa ant el a ee as 9 6 21 ANGU AA 10 6 21 WA WM WA WAN WA WA WA WAA Terre oer 10 R Ka Aa Ta Ya Aa AAA AAA AAA A E AU 10 6 2 3 Na AA ui aa Saa 10 6 2 4 C nfig ration Parameters IA a a aa a a a a 11 6 3 Ndi LED Srani a a a a ia 11
7. emoryO 0t037 ParM16 Format 10 7 hast Fautt Oto 37 Par M17 Format 10 C _ a aa FWD ON OF T On B gt REVO ON Off On Bi J3 J Fait OA Bo 4 Frequency __10 0 1 0 __ BI 5 J Freq LevelDetect _ O Off1 On f Ready __ 0 BI 7 Torque Limit Active 0 Off1 On Voltage Limit Active O Off 1 On Current Limit Active _ O Off 1 On _ __ ee 0 Off 1 0n Defined by Config E24 Point Description Range Value Par AA Reference Frequenc 0 400 00 505 Universal 20000 to 20000 Must set 1 10 UserDefined User Defined ii ae Par 505510 Selects Ramp 4 O of 1 on lt Tooge 10 Min on time 20msec ee le HMS INDUSTRIAL NETWORKS AB 13
8. herwise the switch has to be in OFF position Please Note If an external termination connector is used the switch must be in OFF position Termination switch ON Bus termination enabled If the module is the last or first module the bus termination has to be set on or an external termination connector has to be used Termination switch OFF Bus termination disabled 6 2 3 Node Address Before power on OPC G11S PDP the node address has to be set This is done with the DIP switch on the module this enables address settings from 1 255 DIP switch nr Value 1 1 2 2 3 4 4 8 5 16 6 32 7 64 8 128 Example Setting DIP switch 1 3 and 6 to ON gives node address 37 1 4 32 Please Note The node address can not be changed during operation HMS INDUSTRIAL NETWORKS AB 10 USER MANUAL Revision 1 01 2000 11 06 6 2 4 Configuration parameters The following parameters affect the operation of the Metasys 2 option Operation parameter Description Validinputvalues Default value Loss of network behavior e 0 Immediate trip Code ERR5 e 1 ERR5 trip after timer setting 028 e 2 Re check after timer setting 028 e Ignore communication error ERR5 timer setting 0 0 60 0 5 0 0 seconds used with 027 Description of Parameters 027 and 028 Parameters 027 configures how the drive reacts to loss of network Out of the four settings the first 0 setting allows for an immediate trip
9. rmation to start up and configure the 115 2 6 1 Physical interface Isolation The bus is galvanically separated from the other electronics with an on board DC DC converter Bus signals N2 and N2 are isolated via opto couplers Bus connection The 115 2 connects to the etasys network with 9 pin female DSUB connector a 6 pole terminal block For the pin layout refer to Table 1 Pin Pin DSUB Name Function Terminal Shield Connected to PE Physical Earth Not used 2 oe ee Not used 5 Ref Isolated GND from RS 485 side ls 5V BUS Isolated 5V from RS 485 side Negative RxD TxD according to RS 485 specification Positive according to RS 485 specification Not Connected e 5V BUS and Ref are used for bus termination Some devices like optical transceivers 5485 to fiber optics might require external power supply from these pins Table 1 Pin Layout HMS INDUSTRIAL NETWORKS AB 9 USER MANUAL Revision 1 01 2000 11 06 6 2 Configuration 6 2 1 Baudrate The baudrate Metasys 2 network is always 9600kbps 6 2 2 Termination The end nodes in a Metasys network can be terminated to avoid reflections on the bus line The OPC G11S 2 is equipped with a termination switch to accomplish this in an easy way If the module is used as the first or last module in a network the termination switch should be in ON position Ot
10. when a network problem occurs The last setting 3 configures the drive to ignore the error The middle two settings 1 and 2 use a timer setting 028 in conjunction with the error setting Parameter 028 contains the timer setting that is used when 027 is configured for a value of 1 or 2 6 3 Indication LED s The OPC G11S M 2 is equipped with four LED s The functions of the LED s are described in Figure 1 and Table 2 1 Power Error 2 Not Used 3 4 Fieldbus diagnostics Not Used HMS INDUSTRIAL NETWORKS AB 11 USER MANUAL Revision 1 01 2000 11 06 z 4 Figure 1 LED s Name Power Error Fieldbus diagnostics Table 2 LED functionality HMS INDUSTRIAL NETWORKS AB m Function Turned On Module running in normal mode Turned On Hardware fault Flashing Red 1 Hz Error during initialization of inverter communication Turned On Permanent communication error M odule Offline Irregular Flash Communication error Flashing Red 1 Hz Error during initialization of the M etasys channel Turned Off No diagnostics present 12 USER MANUAL Revision 1 01 2000 11 06 7 Operating the drive via Metasys 2 This section describes how to control drive via control word status word and how to access drive parameters Point Description NPT NPA Range Value Notes Al 4 Motor output power Oto 200 00 Par M10_ fe Faultm
Download Pdf Manuals
Related Search