Home

SKF Reliability Systems standard product catalogue

1. CMSS 26xx Temperature Magnet 4 10 cm Stinger CMSS 60139 04 SKF Reliability Systems standard product catalogue www skf com cm 21 SKF Machine Condition Detector Pro IS CMVL 3600 IS Ordering information MCD Pro IS Machine Condition Detector CMVL 3600 IS K 01 C Machine Condition Detector MCD Pro IS Kit Each CMVL 3600 IS K 01 C Kit consists of the following items e MCD Pro IS Machine Condition Detector probe CMVL 3600 1S e MQC MARLIN QuickConnect 1 4 28 stud one 1 31706301 e Temperature magnet for MCD Pro IS Machine Condition Detector probe CMAC 3610 e Stinger probe 4 10 cm CMSS 60139 04 e AA Alkaline batteries two 2 e MCD Pro IS Machine Condition Detector setup key CMAC 3620 e MCD Pro IS Machine Condition Detector padded carrying Case 31736700 e MCD Pro IS Machine Condition Detector user manual CMVL 3600M SL e MCD Pro IS Machine Condition Detector quick start card CMVL 3600 QS MQC MARLIN QuickConnect and mounting accessories e MQC MARLIN QuickConnect mechanical M8 x 1 25 mounting thread three 3 studs per package CMSS 2600 3 MQC MARLIN QuickConnect mechanical 1 4 28 mounting thread three 3 studs per package CMSS 2610 3 MQC MARLIN QuickConnect computerized patent pending M8 x 1 25 mounting thread three 3 studs per package CMSS 2601 3 MQC MARLIN QuickConnect computerized patent pending 1 4 x 28 mounting thr
2. Machines of this group mostly have sleeve or rolling element bearings SKF Reliability Systems standard product catalogue www skf com cm 5 SKF Vibration Pen s CMVP 40 CMVP 50 Specifications Ordering information Vibration pickup Piezoelectric acceleration integrated sensor compression e CMVP 40 EN Vibration Pen english system in s equivalent type Peak includes two 2 CR2032 lithium batteries a leather Measurement range 110 55 mm s RMS 0 06 to 3 00 in s equivalent belt holster Vibration Severity Card anda English language Peak manual Tolerance 10 and 2 digits measured at 80 Hz Frequency range e CMVP 50 EN Vibration Pen s metric system mm s RMS Overall vibration 10 Hz to 1 000 Hz Tolerances measured within the includes two 2 CR2032 lithium batteries a leather belt frequency range are in accordance with ISO 3945 and 2 digits holster Vibration Severity Card and a English language Acceleration enveloping 10 kHz to 30 kHz manual Display Measurement value 3 5 digit LCD l l e CMVP 50 DE Vibration Pen s metric system mm s RMS includes two 2 CR2032 lithium batteries a leather belt holster Vibration Severity Card and a German language Display cycle Approximately one 1 second Overload indication OVER Battery replacement indication BATT Hold indication HOLD manual Power Two 2 CR2032 lithium batteries e CMVP 50 FR Vibration Pen s metric system mm s RMS Battery lifetime 170 mA
3. Non contact Thermometer CMSS 2020 e Laser sighted e Fast and easy to use e Compact rugged size For additional information please refer to the previous section containing the SKF Microlemp Non contact Thermometer Ordering information e CMPK 200 PLUS EN Basic Condition Monitoring Kit includes CMVP 50 EN Vibration Pens metric system mm s RMS with English user manual CMSS 2020 SL MicroTemp Non contact Thermometer CMIN 400 K Inspector 400 Ultrasonic Probe with headphones Custom hard shell carrying case Batteries included e CMPK 200 PLUS DE Basic Condition Monitoring Kit includes CMVP 50 EN Vibration Pen metric system mm s RMS with German user manual CMSS 2020 SL MicroTemp Non contact Thermometer CMIN 400 K Inspector 400 Ultrasonic Probe with headphones Custom hard shell carrying case Batteries included e CMPK 200 PLUS FR Basic Condition Monitoring Kit includes CMVP 50 EN Vibration Pens metric system mm s RMS with French user manual CMSS 2020 SL MicroTemp Non contact Thermometer CMIN 400 K Inspector 400 Ultrasonic Probe with headphones Custom hard shell carrying case Batteries included e CMPK 210 PLUS EN Basic Condition Monitoring Kit includes CMVP 50 EN Vibration Pen s english system in s equivalent Peak with English user manual CMSS 2020 SL MicroTemp Non contact Thermom
4. 250 Hz 500 Hz for CMSS 3812 Velocity Sensor only e E1 50 Hz e E2 250 500 Hz e E3 250 500 1k 2k 5k Hz e E4 250 500 1k 2k 5k 10k Hz Lines of resolution 1600 800 400 Averaging Stable exponential peak hold 1 2 4 8 times Window Hanning Measurement mode Normal recorder post process e Normal Recording time of waveform data is determined by FFT measurement condition analysis frequency line number Executes the measurement for average cycle in FFT and records the waveform for frame time final frame time e Recorder Records the waveform of specified time by Rec time Average cycle of FFT is one time e Rec Time 1 2 5 10 sec e Post process Calculates from raw waveform data temporary saved data Average cycle of FFT is one time Judgment Abnormal judgment by vibration severity standard ISO 10816 JIS B 0906 Standard Adnormal bearing judgment by enveloped acceleration E3 mode www skf com cm 25 Ordering Information MicroVibe P Kit CMVL 3850 ML includes e MicroVibe P Module e CMSS 3811 Accelerometer 1 5 meters 5 feet integral cable with plug and stinger one 1 each e CMAC 3825 Two Bar Magnetic Base high strength 35 lb pull one 1 each e CMAC 3830 Earphones one 1 each e Data Management software CD ROM one 1 each e MicroVibe P documentation English and German User manual PDF Data management software manual PDF Quick start
5. displacement and enveloped rh 0 409 0 647 acceleration simultaneously s Ww 36 67 52 25 SKF s Multi point automation mms saves time and enhances the a 184 3 ump p power accuracy and overall 0 017 0 078 reliability of your decision SE making giving you the information needed to make Done the best possible judgment call 152 Vibration Evaluation Measured Value 3 159 mmja Vibration Sewerik a Small machine Bearing Evaluation Measured Value 5 771 GE Judgement Judgement The MicroVibe P provides extensive automatic setup and evaluation of vibration results Simply collect the data and MicroVibe P does the rest comparing readings to pre programmed velocity and enveloped acceleration severity criteria for a reliable and accurate evaluation of vibration severity This allows even novice users to easily determine abnormal conditions and take appropriate action FFT spectrum analysis capabilities With pre set measurements and user selectable FFT resolution at 400 800 or 1600 lines selectable Fmax and a 90 db dynamic range the MicroVibe P has what it takes to help you easily pinpoint impending machine problems Cursor position SKF Reliability Systems standard product catalogue www skf com cm DS readout with display zoom HF Microvibe P 4 14 04 amp optimizes your analysis power Ede KHHKK In addition it automatically DataNo 8 tabulates and displ
6. A E3 E4 76 8 kHz frequency E1 E2 V D 38 4 kHz Aliasing A E3 E4 20 kHz filter E1 E2 V D 2 kHz Range A E1 E2 0 1 g 100x range E3 E4 0 5 g 20x range 0 20 g 5x range 0 100 g 1x range V 10 mm s 100x range 0 0 50 mm s 20x range 0 200 mm s 5x range 0 1000 mm s 1x range D 0 50 um 100x range 0 250 um 20x range 0 1000 um 5x range O0 5000 um 1x range 1 The upper bound frequency can be changed by Utility Menu s A Filter Overall and judgment specifications Item Specifications Simultaneous measurement of overall vibration level multi mode A V D E1 E4 Range Auto Measuring Time 0 1 s 0 5 s 1 0s Measurement data RMS value PEAK value C F value Measured value display digits Significant figure 4 digits Example 9999 999 9 99 99 9 999 Status Display Under measurement measurement end Overall value simultaneous measurement Item Specification Graph FFT graph display e Dominant frequency component highest 5 frequencies e Cursor indication value display e Zoom scroll value display Waveform graph e Cursor indication display e Zoom scroll display FFT specifications Item Specifications FFT Mode A V D E1 E2 E3 E4 waveform Range Fixed auto analysis FFT measurement condition Analysis frequencies Selection list e A 250 500 1k 2k 5k 10k 15k 30k Hz e V 250 500 1k Hz e D
7. C 30 F to 500 F 2 of reading Micro Temp Non contact Thermometer or 2 C 3 5 F whichever is greater 18 C to 1 C 0 to 30 F 3 C 5 F Weight 227 g 0 5 lb e CMPK 200s Basic Condition Monitoring Kit e CMPK 210 s Basic Condition Monitoring Kit Dimensions 152 mm x 101 mm x 38 mm 6 0 x 4 0 x 1 5 Ambient operating range O to 50 C 32 F to 120 F Relative humidity 10 to 95 relative humidity noncondensing at up to 30 C 86 F Power 9 V Alkaline or NiCad battery SKF Reliability Systems standard product catalogue www skf com cm ALS SKF Basic Condition Monitoring Kit CE CMPK 200 s metric system CMPK 210 s english system e Check bearing and machine condition quickly and easily e Reduce unexpected downtime An essential collection of monitoring tools that no industrial manufacturing plant should be without Makes condition monitoring a simple task for maintenance operations reliability and vibration analysis departments A powerful combination for detection of machine and bearing defects Multi parameter condition monitoring e Vibration Pen CMVP 40 CMVP 50 e Microlemp Non contact Thermometer CMSS 2020 e nspector 400 Ultrasonic Probe CMIN 400 CMPK 200 Kit metric system includes CMVP 50 metric system mm s RMS Vibration Pen with carrying case CMSS 2020 Microlemp Non contact Thermometer CMIN 400 Inspect
8. ISO Standard 10861 1 Enveloped acceleration 0 3 gE 20 0 gE Temperature 0 C to 100 C 32 F to 212 F Frequency range Overall velocity 10 Hz 1 kHz Tolerances measured within the frequency range are in accordance with ISO 3945 Enveloped acceleration band 3 500 Hz 10 kHz DISPLAY Viewing area 54 99 mm x 17 78 mm 2 165 x 0 700 POWER Main power Two 2 1 5 V alkaline AA batteries Battery lifetime 30 hours Backup battery One 1 3 V BR1225 Lithium lon Battery Auto off Two 2 minute countdown on last operation HAZARDOUS AREA RATINGS Intrinsic Safety IS Ex ATEX II1G EEx ia IIC T4 Ta 20 C to 40 C Class Division 1 Groups A B C D T3A USA Canada PHYSICAL CHARACTERISTICS Case Water and dust resistant IP 65 Drop test Six 6 feet on multiple axes Dimensions Length 190 5 mm _ 7 50 Width 43 2 mm 1 70 Height 41 4mm 1 63 Weight 431 gms 0 95 lb with battery 635 gms 1 4 lb with temperature magnet probe tip USER ENVIRONMENT Operating temperature 20 C to 60 C 4 F to 140 F ordinary locations 20 C to 40 C 4 F to 104 F hazardous locations Storage temperature 37 C to 70 C 34 F to 158 F Humidity 5 to 95 noncondensing COMMUNICATIONS PORT Type Micro D RS 232 QUICKCONNECT INTERFACE Receptacle 1 4 turn 5 8 24 two 2 lead thread with contact Accessories to fit MQC QuickConnect Stud series
9. Mark SKF Loop Powered Vibration Transmitter CMSS 420VT and displays CMSS 420LCD and CMSS 420LED SKF Loop powered Vibration Transmitter CMSS 420VT Ordering information CMSS 420VT 1 25 4 mm sec 0 1 in sec RMS Optional display includes 1 4 28 and M8 Mounting Studs Light Emitting Diode Display LED Liquid Crystal Display LCD CMSS 420VT 2 50 8 mm sec 0 2 in sec RMS CMSS 420LED 01 0 1 in sec CMSS 420LCD 01 0 1 in sec includes 1 4 28 and M8 Mounting Studs CMSS 420LED 02 0 2 in sec CMSS 420LCD 02 0 2 in sec CMSS 420LED 51 25 4 mm sec CMSS 420LCD 51 25 4 mm sec CMSS 420LED 52 50 8 mm sec CMSS 420LCD 52 50 8 mm sec Accessories CMSS 420LCD CMSS 420LED Display Retrofit requires CMSS 420EL 90 Degree 3 4 by 3 4 NPT Elbow transmitter Useful for connecting CMSS 420VT to hard or flexible conduit When used with the CMSS 420WF provides a simple weatherproof exit for the instrument wire LCD displays actual vibration levels in velocity on a Liquid Crystal display LED displays actual vibration levels in velocity on a Light Emitting Diode display The displays are shipped loose and it is CMSS 203 Pipe Thread a simple installation Includes a BNC Accelerometer Mounting Adapter connector that provides access to the raw acceleration signal They are provided in several NPT sizes to accommodate the most common plugs found on most machinery The adapters have a CMSS 420BNC BNC Adapter Retrofit
10. S 30 1 at focus point MIN MAX AVG DIF temperature display Data logging 12 points Probe jack Display hold 7 seconds Hi low alarm LCD backlit Temperature display C or F selectable Display resolution 0 1 C 0 1 F Hard carrying case Locking trigger Tripod mounting 6 35 mm 1 4 20 UNC threading Ordering information e CMSS 2000 SL Temperature Probe including multilingual user manual English French German Portuguese and Spanish alkaline battery hard case and wire strap Optional kits that includes the CMSS 2000 SL Temperature Probe e CMPK 60 5 Bearing Analysis Kit english system includes CMSS 2000 SL Temperature Probe TMEH1 OilCheck Monitor CMVP 40 Vibration Pen e CMPK 70 5 Bearing Analysis Kit metric system includes CMSS 2000 SL Temperature Probe TMEH1 OilCheck Monitor CMVP 50 Vibration Pen ls SKF Microlemp CE Non contact Thermometer CMSS 2020 SL Features e Laser sighted e Fast and easy to use e Compact rugged size Introduction The SKF MicrolTemp Non contact Thermometer CMSS 2020 takes the surface temperature of almost any object quickly and easily Just aim pull the trigger and read the temperature on the display Surface temperatures of hot hazardous or hard to reach objects can safely be measured without contact Its compact size makes it handy for use in the electrical industrial automotive diesel food safety and vario
11. arcing tracking and corona in electric apparatus e Test bearings pumps motors compressors etc Introduction The Inspector 400 Ultrasonic Probe senses high frequency sounds produced by operating equipment leaks and electrical discharges It electronically translates these signals by a heterodyning process making them audible so that a user can hear these sounds through a headset and see them as intensity Increments on a meter The Inspector 400 can complement your condition monitoring program by providing you with the following capabilities Pressure vacuum leaks As any gas air oxygen nitrogen etc passes through a leak orifice it generates a turbulent flow with detectable high frequency components By scanning the test area with the Inspector 400 a leak can be heard through the headset as a rushing sound or noted on the meter bar graph indicator The closer the instrument is to the leak the louder the rushing sound and the higher the meter reading Should ambient noise be a problem a rubber focusing probe may be used to narrow the instrument s reception field and to shield it from conflicting ultra sounds Valve Valve activity such as leakage or blockage can be accurately checked while the valve is on line Properly seated valves are relatively quiet while leaking valves produce a turbulent flow as the fluid moves from the high pressure side through the leak to the low pressure side Due to a wide sensitivity and ul
12. objects without contact The non contact thermometer senses the energy of an object with an infrared detector When pointed at an object the infrared detector collects energy producing a signal that the microprocessor translates as a reading on the backlit display As the trigger is squeezed the object temperature Is continuously measured by the infrared detector This allows for HI and LOW audible and visual alarms C or F selectable low fast and accurate real time readings battery indicator recall last reading and adjustable emissivity for more accurate temperature measurements Simply point shoot and read No contact with hot surfaces or moving parts means safer faster and easier temperature Units are molded from high strength solvent resistant plastic measurements The optics are recessed for added environmental protection A o cable strap anchor is provided for the belt clip This instrument features a 32 C to 600 C 25 F to 1100 F temperature range laser sighting LCD backlight Hard case MAX MIN AT and AVG temperatures recall last reading A water resistant dust proof case which holds the unit includes belt clip and measures 245 mm x 169 mm x 52 mm 9 6 x 6 6 x 2 0 is included SKF Reliability Systems standard product catalogue www skf com cm 10 SKF Temperature Probe CMSS 2000 SL Applications Find hot spots in electrical connections Find hot spots in motors and bearin
13. 90 Degree 3 4 NPT conduit elbow with a BNC connector to access the raw 1 4 28 threaded hole to mate acceleration signal This is useful for with the CMSS 420VT and most connection to portable data collectors common accelerometers and vibration transmitters CMSS 420WF 3 4 NPT Weatherproof Cable Fitting When used with the CMSS 420EL MONADA DEDE provides a simple weatherproof exit U Ny National BE Apere ira for the instrument wire NOTE Maximum load resistance calculations RLoad Vs 13 5 Vd 0 032 Where RLoad Load Resistance Vs DC Supply Voltage Vd Display Voltage 5 0 Vdc for LED 2 0 Vdc for LCD O Vdc if not using a display unit For Example Using a LED Display and a Supply Voltage of 24 Vdc Supply Voltage Vs 24 V Display Voltage Vd 5 0 Vdc for LED RLoad Vs 13 5 V Vd 0 032 24 V 13 5 V 5 Vdc 0 032 172 Ohm SKF Reliability Systems standard product catalogue Product Support Plan PSP A range of Product Support Plans are available to protect your investment Contact your local SKF Reliability Systems Sales Representative for additional information For additional information on SKF Reliability Systems products contact SKF Reliability Systems 52 71 Viewridge Court San Diego California 92123 USA Telephone 1 858 496 3400 e FAX 1 858 496 3531 Web Site www skf com cm The contents of this publication are the copyright of the publisher and may not b
14. IN 400 K SKF Temperature PROBE suiserarsnesnsuccincrrnmeniine 9 CMSS 2000 SL SKF MicroTemp Non contact Thermometer J gt CMSS 2020 SKF Basic Condition Monitoring Kit sissssssisissesessssisiassssssssesoesesrs 15 CMPK 200 5 CMPK 210P SKF Bearing Analysis IU vescaesascsarscapessesseuascdirnaseceomesnistieteriereet 17 CMPK 60 CMPK 7 Plus SKF Machine Condition Detector Pro IS we ceeeeseeeeeeeees 19 CMVL 3600 IS Machine Reliability Inspection System Intrinsically Safety IS rated SRF MITOVE P sinergien atten awacaese renee 22 CMVL 3850 SL SKF Loop powered Vibration Transmitter wo cece 26 CMSS 420VT Product Support Plans PSP wl ee seeeeceeeeeceees Back Cover SKF Reliability Systems standard product catalogue www skf com cm 3 SKF Vibration Pen s CE CMVP 40 english system in s equivalent Peak CMVP 50 metric system mm s RMS Overall vibration and enveloped acceleration Overview A multi parameter approach to condition monitoring provides two different methods for monitoring machinery condition This allows for early detection of specific machinery problems and provides more ways to measure changes in machinery condition The SKF Vibration Pen s is a multi parameter vibration monitoring tool capable of measuring vibration caused by rotational and structural problems like imbalance misalignment looseness etc and capable of measuring vibration in higher frequencies caused by rolling e
15. SKF Reliability Systems standard product catalogue Introduction Global presence local solutions With over 100 years of experience SKF stands alone as a total solution provider for maximizing machine and plant productivity With a reputation for quality technological innovation and service that spans the globe SKF brings what no other vendor can to the maintenance arena Local SKF sales and service representatives and worldwide distributors provide access to the range of SKF bearings maintenance products lubricants and condition monitoring instrumentation and software independent of your location In any kind of rotating machinery from huge rolling machines to the smallest of motors the bearing knows if there Is a potential problem As the primary interface between moving parts the bearing is literally the diagnostic heart of the machine Misalignment unbalance looseness and friction are all telegraphed through the bearing Understanding the information coming from this diagnostic pulse and then applying the latest and best technology to the problem is the key to raising machine productivity and lowering operating costs This standard product catalogue features a convenient collection of monitoring tools that no industrial manufacturing plant should be without Table of contents SKF WGI Pen sesers CMVP 40 in s equivalent Peak CMVP 50 mm s RMS SKF Inspector 400 Ultrasonic Probe esseere 6 CM
16. ager NI Non incendive Class Division 2 CMDM 6220 MARLIN I Pro NIA Bar Code Imager NI Non incendive ATEX Zone 2 CMDM 6230 MARLIN l Pro IS data manager Class Division 1 Groups C and D CMDM 6350 MARLIN S Pro IS data manager ATEX Zone 1 CMDM 5360 SKF Reliability Systems standard product catalogue www skf com cm 22 SKF MicroVibe P CMVL 3850 ML Power without complexity an advanced instrument for simplified vibration assessment that fits in your pocket Now available in multiple languages ML English Chinese German and Spanish With SKF s new MicroVibe P vibration assessment is as close and convenient as your PDA This economical vibration meter expansion module fits in a PocketPC s compact flash card slot CF Type Il and features the user friendly Windows Mobile Operating System Identify problems and assess machine condition guickly and easily with this versatile and easy to use pocket tool Power without complexity A handy quick check solution based on the universal PDA platform MicroVibe P is simple to use Built in automatic functions virtually eliminate setup while the analytical displays and automatic judgment of machine vibration readings help users identify machine problems on the spot Features e Exceptional value Low cost compact lightweight works with many Pocket PC PDA s by Hewlett Packard Dell Toshiba etc e Quickly identify problems Expert judgmen
17. arly detection of bearing and gear mesh problems Note Enveloped acceleration measurements do not detect rotational or structural vibration caused by imbalance misalignment looseness etc Easy operation Vibration Pen s readings are easily performed simply e Turn the Vibration Pen on e Press the Vibration Pens tool s sensor tip against your machinery measurement POINT e Wait for the readings to stabilize and record the measurement values Easy evaluation The Vibration Pen tool s front panel LCD simultaneously shows overall velocity vibration readings in mm s RMS CMVP 50 or in in s equivalent Peak CMVP 40 and acceleration enveloping readings in g E indicating enveloped acceleration The SKF Vibration Pen severity card provides quick reference for ISO Standard 10816 overall velocity vibration comparisons General severity level guidelines When considering severity levels one should always be aware that even standards can only provide general guidelines to determine initial alarm settings At no time should such guidelines substitute for experience and good judgement The most reliable method of determining alarm settings Is to trend vibration readings over time establish baseline values and alarm settings above baseline values Vibration measured In velocity For velocity vibration ISO standards like ISO 10816 First Edition 1995 or VDI 2056 guidelines are generally acc
18. ays the highest vibration peaks from a spectrum making it easy to quickly identify signals indicative of specific machine problems like misalignment Imbalance or bearing faults Mode Frequency 30kKHz 2006 250 Hz 6 006 3 6000 000 Hz Bios 2993 750 Hz a4 a S0KHzs1 Time waveform displays Measure and store time b Fe P Microvibe P 461157 data with the capability to aco select acquisition type and bo FL IWIN oA DataMo 5 time measurement Time pa Leo displays in acceleration PE TR ER velocity displacement or He 0 047 s ___ 0 170 g 0 031 s 275 5 enveloped acceleration A unique automatic transient capture function starts taking measurements when the signal exceeds a user specified trigger level enabling more detailed analysis of the pre and post trigger events surrounding a change In machine condition 1i 0 05s 1 Menu Versatile measurement capability The MicroVibe P works with the two most commonly used vibration sensors accelerometers and dynamic velocity transducers Both enable you to take a multi parameter approach to your analysis and to optimize vibration data gathering Audio analysis Now you can actually listen to machine problems using the MicroVibe P s acoustic capability Simply connect the earphones and listen to the operation of your machine When abnormal noise is detected use the vibration analysis capabilities of the MicroVibe P to ze
19. densing Weight 25 g 0 88 oz approximate Card only Dimensions 60 0 mm x 42 1 mm x 16 9 mm 2 36 x 1 66 x 0 67 Shape Conforms to CF Card TYPE ll Card Type See photograph Color Black May not work with all PDA s Please see list of Certified PDA s CMSS 3811 Accelerometer Type Pre amp is built in Shear type Power supply DC 5 V Voltage sensitivity 20 mV g Resonance frequency 20 kHz approximate Frequency range 3 Hz to 10 000 Hz Maximum acceleration 500 m s Vibration limit 5000 m s Maximum output voltage 1 V Output impedance Below 100 0 Temperature range 20 C to 80 C 4 F to 176 F Material SUS Weight 60 g 2 1 oz approximate Tapped hole M6 P 1 depth 5 mm internal thread Integral cable Length 1 5 meters 5 feet Connector 8 pin modular plug Dimensions See drawing below Structure Dust proof spray proof CMSS 3811 Accelerometer Dimensions SKF Reliability Systems standard product catalogue SKF MicroVibe P CMVL 3850 ML Measurement Specifications For Measurement with CMSS 3811 Accelerometer Frequency specifications Item Specifications Frequency range A Acceleration 10 15 kHz 1 V Velocity 10 1000 Hz D Displacement 10 150 Hz E1 Envelope Detection 5 100 Hz E2 Envelope Detection 50 1 kHz E3 Envelope Detection 500 10 kHz E4 Envelope Detection 5 k 20 kHz Display specifications Sampling
20. e reproduced even extracts unless permission is granted Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct indirect or consequential arising out of the use of the information contained herein SKF reserves the right to alter any part of this publication without prior notice SKF Patents include US05854553 US05845230 US06489884 US05679900 US04768380 US06199422 US05992237 US06202491 US06513386 US06275781 US06633822 US06006164 US2003_0178515A1 US6 789 025 US6 789 360 US 5 633 811 and US 5 870 699 WO_03_048714A1 e SKF Microlog and MARLIN are registered trademarks of the SKF Group e Microsoft Windows and Excel are registered trademarks and Windows Mobile is a trademark of Microsoft Corporation e All other trademarks are the property of their respective owners CM2355 6 07 e Copyright 2007 by SKF Condition Monitoring Inc ALL RIGHTS RESERVED
21. ead three 3 studs per package CMSS 2611 3 e Tool kit for spot face 1 4 28 CMAC 9600 01 e Tool kit for spot face M8 x 1 25 CMAC 9600 02 e Drill bit for 1 4 28 kit CMAC 9600 03 MQC MARLIN QuickConnect and mounting accessories continued Tap for 1 4 28 kit CMAC 9600 04 Pilot for 1 4 28 kit CMAC 9600 05 Drill bit for M8 x 1 25 kit CMAC 9600 06 Tap for M8 x 1 25 kit CMAC 9600 07 Pilot for M8 x 1 25 kit CMAC 9600 08 End mill or counter bore for either kit CMAC 9600 09 Optional accessories Cable MDM MARLIN I Pro to MCD Pro IS Machine Condition Detector CMAC 6107 MCD Pro IS Machine Condition Detector setup key CMAC 3620 Temperature magnet for MCD Pro IS Machine Condition Detector probe CMAC 3610 Probe tip replacement kit for temperature magnet for MCD Pro IS Machine Condition Detector CMAC 3630 Magnetic probe tip for MCD Pro IS Machine Condition Detector CMAC 3611 Stinger probe 4 10 cm CMSS 60139 04 1 4 28 MQC MARLIN QuickConnect for stinger interface CMSS 2610 1 MCD Pro IS Machine Condition Detector quick start card CMVL 3600 QS MCD Pro IS Machine Condition Detector user manual CMVL 3600M SL MARLIN data manager The MARLIN MCD Pro IS can be used in non hazardous conditions with the following MARLIN data managers as well as all international language translation kits MARLIN l Pro CS Bar Code Scanner CMDM 6210 MARLIN I Pro NI2 Bar Code Im
22. epted ISO 10816 with the title Mechanical vibration Evaluation of machine vibration by measurements on non rotating parts consists of six parts Part 1 10816 1 determines general guidelines and are superseded by the following more explicit parts of ISO 10816 like part 2 10816 2 for Land based steam turbines and generators in excess of 50 MW with normal operating speeds of 1500 r min 1800 r min 3000 r min and 3600 r min The severity chart shown in Table 1 is In accordance with the ISO 10816 2 guidelines For exceptions to this guideline and for more details please refer to the ISO 10816 2 document itself Industrial machines with nominal power above 15 kW and nominal speeds between 120 rpm and 15000 rpm when measured in situ are covered by ISO 10816 3 The machines are separated into four different groups Group 1 Large machinery and electrical machines with shaft height greater than 315 mm These machines are normally equipped with sleeve bearings Group 2 Medium size machines and electrical machines with shaft height in between 160 mm and 315 mm These machines are normally equipped with rolling element bearings and operating speeds above 600 rpm Group 3 Pumps with multivane impeller and with separate driver with rated power above 15 kW Machines of this group may be equipped with sleeve or rolling element bearings Group 4 Pumps with multivane impeller and with Integrated driver
23. eter CMIN 400 K Inspector 400 Ultrasonic Probe with headphones Custom hard shell carrying case Batteries included SKF Reliability Systems standard product catalogue www skf com cm Ay SKF Bearing Analysis Kit CE CMPK 60s english system CMPK 70 s metric system e Check bearing and machine condition quickly and easily e Reduce unexpected downtime A convenient collection of monitoring tools that no industrial manufacturing plant should be without Makes condition monitoring a simple task for maintenance operations reliability and vibration analysis departments Monitor vibration temperature and oil condition with e Vibration Pen CMVP 40 CMVP 50 e Non contact Temperature Probe CMSS 2000 SL e OilCheck Monitor TMEH1 CMPK 60 5 Bearing Analysis Kit english system includes e CMVP 40 english system in s equivalent peak Vibration Ordering information anes Pens with manual carrying case severity card and battery e CMPK 60 PLUS EN Bearing Analysis Kit includes e CMSS 2000 SL Laser Sighted Non contact Temperature CMVP 40 EN Vibration Pen s english system in s Probe with manual hard case belt clip and battery equivalent Peak with English user manual e SKF TMEH1 OilCheck with manual soft carrying case and CMSS 2000 SL Temperature Probe including hard case battery and wrist strap multilingual user manual English French German Portuguese and Spanish TMEH1 OilC
24. etic bases for automatic collection of vibration and temperature data Green yellow and red LEDs provide easy to interpret indications of machine status so operations or maintenance personnel can quickly identify the need for more In depth analysis on a particular machine Multi parameter monitoring capabilities The Machine Condition Detector Pro IS operates as a stand alone device or as an accessory to the SKF MARLIN hand held mobile computers for Operator Driven Reliability ODR When used with SKF Machine Inspector companion software and the MARLIN QuickConnect Line of mechanical and computerized studs the complete system offers customers in non hazardous conditions the added power and functionality of immediate in the field feedback on alarm conditions as well as data storage trending and analysis Data is logged for trending SPC Statistical Process Control rule violation and percent change from last measurement and baseline data SKF Operator Driven Reliability ODR process ensures that operator observations are accurately thoroughly and consistently recorded and communicated Utilizing automated technology that Is linked to your maintenance strategy operators immediately respond to abnormal process conditions proactively with in the field corrective actions that help increase production output In the event of degrading asset health operators can initiate work notifications to your computerized maintenance management
25. gs Examine temperature differences in engine blocks to eliminate costly breakdowns Verify the temperature of asphalt welded membranes and rooftop HVAC components D gt Ne Measure a steam trap line for temperature differences Make sure that the diameter of the pipe fills the field of view Scan a moving surface to examine a dynamic thermal profile Laser sighting With offset single point laser sighting the laser point shows the approximate center of the area measured Extra bright laser point How to accurately measure temperature Locating a hot or cold spot To find a hot or cold spot aim the thermometer outside the area of interest Then slowly scan across the area with an up and down motion until you locate the hot or cold Spot Field of view Make sure that the target is larger than the unit s spot size The smaller the target the closer you should be to it See the diagram on the side of the unit Emissivity Emissivity is a term used to describe the energy emitting characteristics of materials Most organic materials and painted or oxidized surfaces have an emissivity of 0 95 Inaccurate readings can result from measuring shiny or polished metal surfaces To compensate for this adjust the unit s emissivity reading or cover the surface to be measured with masking tape or flat black paint lt 148 C 300 F Allow time for the tape or paint to reach
26. guide PDF CE declaration of confirmation e Carrying case NOTE Pocket PC PDA NOT INCLUDED Additional Accessories e CMSS 3811 Accelerometer 1 5 meters 5 feet integral cable replacement with plug and stinger one 1 each e CMSS 3812 Velocity Pickup Sensor 1 5 meters 5 feet integral cable with plug one 1 each e CMAC 3825 Two Bar Magnetic Base high strength 40 lb pull one 1 each e CMAC 3830 Earphones one 1 each Certified Pocket PC PDA s with Windows Mobile 2003 2005 Certified Pocket PC PDA s with Windows Mobile 2003 e Hewlett Packard iPAQ hx2400 iPAQ hx2700 iPAQ hx2750 iPAQ hx4700 e Toshiba e830 e ASUS MyPal A730 e Dell AXIM X50 NOT 51 Compatible Pocket PC PDA s with Windows Mobile 2003 e Hewlett Packard iPAQ h2210 iPAQ h2215 e Toshiba e800 Certified Pocket PC PDA s with Windows Mobile 2005 e Hewlett Packard iPAQ hx2490 IPAQ hx2790 SKF Reliability Systems standard product catalogue www skf com cm 26 SKF Loop powered Vibration Transmitter CMSS 420VT Features e Solid state reliability e Integral sensor e 4 20 mA output e Dynamic signal output Description The CMSS 420VT is a solid state loop powered vibration transmitter It provides a 4 20 mA output that is proportional to overall vibration in terms of velocity The CMSS 420VT continuously monitors machinery health and transmits directly into a PLC or DCS fo
27. heck Monitor soft carrying case manual in CMPK 70 s Bearing Analysis Kit metric system English language Includes Custom hard shell carrying case Batteries included e Custom hard shell carrying case e CMVP 50 metric system mm s RMS Vibration Pen s with manual carrying case severity card and battery e CMPK 70 PLUS EN Bearing Analysis Kit includes e CMSS 2000 SL Laser Sighted Non contact Temperature CMVP 50 EN Vibration Pen s metric system mm s RMS Probe with manual hard case belt clip and battery with English user manual e SKF TMEH1 OilCheck with manual soft carrying case and CMSS 2000 SL Temperature Probe including hard case and wrist strap multilingual user manual English French German Portuguese and Spanish TMEH1 OilCheck Monitor soft carrying case manual in English language Custom hard shell carrying case Batteries included battery e Custom hard shell carrying case SKF Reliability Systems standard product catalogue www skf com cm 18 SKF Bearing Analysis Kit CMPK 60 s CMPK 70P s The SKF Bearing Analysis Kit consists of SKF Vibration Pen s CMVP 40 in s equivalent Peak CMVP 50 mm s RMS e So light and compact it fits in your shirt pocket e Easy to operate e Measures according to ISO 10816 standards For additional information please refer to the previous section containing the Vibration Pen s OilCheck a TMEH1 e Shows cha
28. hours current consumption includes two 2 CR2032 lithium batteries a leather belt Measurement mode 7 5 mA holster Vibration Severity Card and a French language HOLD mode 3 0 mA manual Auto power off function Power is turned off approximately two minutes after last ON or HOLD operation Dimensions Height 17 8 mm 0 7 Width 30 5 mm 1 2 Length 157 5 mm 6 2 Weight Approximately 77 g 2 7 oz with batteries Ambient operating conditions 10 C to 50 C 14 F to 122 F 20 to 90 relative humidity ISO International Organization for Standardization Table 1 Vibration severity chart ISO 10816 2 Table 2 Vibration severity chart ISO 10816 3 ISO 10816 2 Steam Turbines and Generators ISO 10816 3 Machinery Machinery Velocity need on Groups 2 and 4 Groups 1 and 3 n e 1500 or 1800 3000 or 3600 CMVP 40 CMVP 50 ea in sec eq msec 15 KW 300 kW Group 1 300 kW 50 MW 0 66 11 8 DAMAGE OCCURS Peak RMS Group 3 Above 15 kW 0 56 61 11 0 oer 110 DAMAGE OCCURS 0 47 8 5 0 42 7 5 RESTRICTED OPERATION RESTRICTED OPERATION 0 29 53 0 08 1 4 NEWLY COMMISSIONED 008 oa pooo 0 00 00 MACHINERY 0 04 0 7 000 oo NEWLY COMMISSIONED MACHINERY SKF Reliability Systems standard product catalogue www skf com cm 6 SKF Inspector 400 Ultrasonic Probe CMIN 400 K Features e Detect pressure and vacuum leaks including compressed air e Check steam traps and valves quickly and accurately e Detect
29. ich are dirt soot fuel water antifreeze and metal particles These elements give a marked increase in the OilCheck s reading and will give immediate warning of possible resulting failure Technical Data Suitable oil types Mineral and synthetic oils Repeatability Better than 5 Readout Green red grading numerical value O 100 Battery 9 V Alkaline IEC 6LR61 Battery lifetime gt 150 hours or 3 000 tests Dimensions 250 mm x 95 mm x 32 mm 9 8 x 3 7 x 1 3 NOTE The SKF OilCheck is not an analytical instrument It is an instrument to detect only changes in the oil condition The visual and numerical readouts are purely a guide to enable trending of the comparative readings of a good oil to a used oil of the same type and brand SKF Reliability Systems standard product catalogue www skf com cm A SKF Machine Condition Detector Pro IS CMVL 3600 IS Machine Reliability Inspection System Intrinsically Safety IS rated The SKF Machine Condition Detector Pro IS MCD Pro IS is certified Intrinsically Safe IS for Europe and North America The ruggedized MCD Pro IS is ideal for use in the hazardous environments typically found in the petrochemical Industrial marketplace Go No Go machine monitoring The Machine Condition Detector Pro IS is designed to provide a straightforward approach to machinery monitoring The instrument s sensor affixes to a machine point via a MARLIN QuickConnect MQC Stud or magn
30. instruments with an ultrasonic input port HAONGNBANGNN Heat exchangers boilers and condensers In leakage or pressure leakage can be readily located with the Inspector 400 Fittings valves flanges are all easily scanned for leakage The high frequency short wave nature of ultrasound allows operators to pinpoint the location of a leak in high noise environments Condenser tubes and heat exchanger tubes may be tested for leakage through two 2 methods Vacuum and Pressure Vacuum The tube sheet is scanned for the telltale rushing sound produced as the leak draws air into the tube Pressure Additional testing may be performed when the system is off line utilizing air pressure around the tube bundle and scanning for the rushing sound produced from the leaking tube Application CMIN 400 K Pressure and vacuum leak detection Valve seat leak detection Exhaust system leaks Heat exchangers boilers condensers Steam trap inspection Bearing testing Gear gear box inspection Tanks pipes etc leak testing Electrical inspection Left to right Valve leakage pressure vacuum leaks mechanical inspection and tank leakage SKF Reliability Systems standard product catalogue www skf com cm 8 SKF Inspector 400 Ultrasonic Probe CMIN 400 K Available Inspector 400 Ultrasonic Probe Stethoscope Scanner kit includes e Inspector 400 ultrasonic probe pistol housing with LED bar graph meter 8 position sensiti
31. ition Detector Pro IS may be easily programmed for six alarm settings which include the alert and danger levels for each of the three measurements When measurements are taken current measured values are automatically compared to six user defined settings and the MCD Pro S s alarm indicator and LED react appropriately An alert condition provides a user with an early warning of impending problems for which immediate in depth analysis should be performed A danger alarm indicates that a problem has escalated to a point where actions must be made quickly to avoid a serious failure MARLIN QuickConnect MQC studs for quality repeatable data collection Specially designed mechanical and computerized studs enable one or several users to collect consistent accurate and repeatable data from each measurement point Engineered to work exclusively with the Machine Condition Detector Pro S MCD Pro IS the MARLIN QuickConnect MQC mechanical computerized studs provide for a fast quarter turn connection which temporarily fastens the probe to a measurement point This reduces the possibility of errors and inconsistencies often resulting from data collected by a variety of individuals using varying methodologies Specifications MEASUREMENTS Vibration pickup Integrated piezoelectric acceleration ceramic shear type Measurement range Velocity 0 3 55 mm s RMS 0 02 3 00 in s equivalent Peak Meets
32. lement bearing or gear mesh problems Multi parameter monitoring is the most thorough and effective method for monitoring bearing and machinery condition The Vibration Pen s tool s multi parameter approach provides accurate and reliable data upon which to base maintenance Many machinery problems may cause excessive overall decisions and promotes early detection confirmation and vibration Mechanical looseness imbalance soft foundation accurate trending of bearing and machinery problems misalignment rotor bow resonance eccentricity bad belts or P lost rotor vanes can all be measured with overall ISO vibration Functional description measurements When performing measurements the Vibration Pen s tool s sensor Input signal is processed to produce two different measurements for each machinery POINT Overall Vibration and enveloped acceleration Measuring the overall vibration of a machine or component or the structure of a machine and comparing the measured value to the machine s normal value or to ISO 10816 standards Indicates machinery health and condition changes iE l The Vibration Pen tool s LCD simultaneously displays both Note Overall vibration is not an indicator of bearing or gear mesh measurement values Depending on the type and location problems that typically occur in higher frequency ranges of the machinery component being measured either or both readings may be of interest Envelo
33. n e CMIN 400 K Inspector 400 Ultrasonic Probe Stethoscope Scanner Kit Accessories and replacement parts e CMAC 8600 1 Lightweight foam lined headset e CMAC 8600 2 Deluxe noise isolating headphones e CMAC 8600 3 Deluxe noise isolating headphones to be worn with hard hat e CMAC 8600 4 Utility belt with holster e CMAC 8600 5 Patented liquid leak amplifier case of 12 x 8 oz bottles used for extremely low level leaks 1 x 10 mil sec e CMAC 8600 6 Stainless steel unisonic scanning module e CMAC 8600 7 Stainless steel stethoscope contact module e CMAC 8600 8 Stethoscope extension rods e CMAC 8600 9 Rubber focusing probe Optional kits that includes the CMIN 400 K Inspector 400 Ultrasonic Probe e CMPK 200s Basic Condition Monitoring Kit e CMPK 210 s Basic Condition Monitoring Kit SKF Reliability Systems standard product catalogue www skf com cm 9 SKF Temperature Probe CE CMSS 2000 SL Laser Sighted Non contact Temperature Probe Features e Single point laser sighting e Adjustable emissivity e High and low alarm e MAX MIN DIF AVG temperature displays e Data logging e Trigger lock e Backlit display e Hard case and wrist strap Introduction There are many uses for this hand held non contact thermometer Compact rugged and easy to use just aim pull the trigger and read the temperature in less than a second You can safely measure surface temperatures of hot hazardous moving or hard to reach
34. nges in oil condition effected by Water content Fuel contamination Metallic content Oxidation e Hand held and user friendly e Numerical readout to facilitate trending The OilCheck detects and measures the dielectric constant of oil By comparing the measurements obtained from used and unused oils of the same brand OilCheck is able to determine the degree of change in the dielectric constant of the oil Dielectric change is directly related to the degradation and contamination level of the oil and helps the user to optimize intervals between oil changes and to detect increased mechanical wear and loss of the oils lubricating properties Laser Sighted Non contact Temperature Probe CMSS 2000 SL e Proven method e High and low alarms e Calculates minimum maximum differential and average temperatures e Expanded temperature range of 32 C to 500 C 25 F to 932 F e Precision laser sighting to pinpoint the target For additional information please refer to the previous off section containing the Laser Sighted Non contact Temperature Probe e Features automatic shut The usual contamination found in oils is caused by oxidation and acid build up which occur during the normal operation of a machine and should show up as a gradual increase in readings over a period of time Other contaminants occur because of excessive wear or mechanical failure the main elements of wh
35. or 400 Ultrasonic Probe with headphones CMPK 210 Kit english system includes Batteries included CMVP 40 english system in s equivalent peak Vibration Vibration severity card Pens with carrying case Belt holder for the Vibration Pens CMSS 2020 MicroTemp Non contact Thermometer CMIN 400 Inspector 400 Ultrasonic Probe with headphones Batteries included Comprehensive quick start Instruction card Rugged carrying case Vibration severity card Belt holder for the Vibration Pen s Comprehensive quick start instruction card Rugged carrying case SKF Reliability Systems standard product catalogue www skf com cm 16 SKF Basic Condition Monitoring Kit CMPK 200 CMPK 210 The SKF Basic Condition Monitoring Kit consists of SKF Vibration Pen l s CMVP 40 in s equivalent Peak CMVP 50 mm s RMS e So light and compact it fits in your shirt pocket e Easy to operate e Measures according to ISO 10816 standards For additional information please refer to the previous section containing the Vibration Pen s SKF Inspector 400 Ultrasonic Probe CMIN 400 Detect pressure and vacuum leaks including compressed air Check steam traps and valves quickly and accurately Detect arcing tracking and corona in electric apparatus Test bearings pumps motors compressors etc For additional information please refer to the previous section containing the Inspector 400 Ultrasonic Probe SKF MicroTemp
36. or D 2 S is shown in the diagram to the NOTE The unit measures the average surface right temperature inside the measurement spot at Focal Point SKF Temperature Probe CMSS 2000 SL Specifications Temperature range 32 C to 600 C 25 F to 1100 F Accuracy assumes ambient operating temperature of 23 C 73 F at calibration geometry For targets above 23 C 73 F 1 of reading or 1 C 2 F whichever is greater 18 C to 23 C 0 to 73 F 2 C 3 F 26 C to 18 C 15 F to O F 2 5 C 4 F 32 C to 26 C 25 F to 15 F 3 C 5 F Repeatability 0 5 or lt 1 C 2 F whichever is greater Response time lt 0 5 second 95 of reading Spectral response 8 to 14 um Emissivity Digitally adjustable emissivity from 0 1 to 1 0 by 0 01 Ambient operating range O to 50 C 32 F to 120 F Relative humidity 10 to 90 relative humidity noncondensing at lt 30 C 86 F ambient Storage temperature 20 C to 60 C 13 F to 158 F without battery Weight 320 g 11 oz Dimensions 200 mm x 160 mm x 55 mm 8 x 6 x 2 Power 9 V Alkaline or NiCad battery Typical battery life Alkaline e 20 hours with laser and backlight on 50 e 40 hours with laser and backlight off Laser sighting Class Il Extra bright laser point Typical distance to target 5 meters 15 feet Distance to spot D
37. ped acceleration Overall vibration Bearing gear mesh frequency vibration 10 kHz to 30 kHz ISO 10816 Part 1 6 Low frequency vibration 10 Hz to gt Enveloped acceleration measurements measure the high 1 kHz frequency repetitive vibration signals typically caused by bearing and gear mesh problems gt Overall velocity vibration occurring in the 10 Hz to1 kHz frequency band Is considered the best operating parameter Envelope detection is very useful in rolling element bearing and for judging rotational and structural problems like gear mesh analysis where a low amplitude repetitive vibration imbalance resonance misalignment looseness and stress signal may be hidden by the machine s rotational and structural applied to components vibration noise SKF Reliability Systems standard product catalogue www skf com cm ik SKF Vibration Pen s CMVP 40 CMVP 50 For example suppose a rolling element bearing has a defect on its outer raceway Each rolling element strikes the defect as it passes the defect Causing a small repetitive vibration signal This vibration signal is of such low amplitude that under normal ISO vibration monitoring it is lost in the machine s other rotational and structural noise Envelope detection filters out low frequency rotational signals then enhances the high frequency defect Signals to focus on repetitive events in the 10 kHz to 30 kHz frequency range and provides an averaged peak value for e
38. r trending alarm and machine shutdown In addition the CMSS 420VT provides access to the dynamic transducer output The buffered output is available for temporary connection of portable analyzers for detailed machine fault analysis Simple installation Simply mount the CMSS 420VT into a 1 4 28 or M8 tapped hole in the bearing housing or machine case NPT Mounting Adapters are available part number CMSS 203 connect two wires into a 4 20 mA loop and you are ready to interface with a PLC or DCS Electrical conduit may be connected directly to the top 3 4 NPT fitting NPT Mounting Adapters are available part number CMSS 203 Specifications DYNAMIC Output 4 20 mA proportional to full scale Velocity Accuracy 5 of full scale Frequency response 2 2 000 Hz Frequency response accuracy 3 db 2 Hz to 2 kHz 10 10 Hz to 1 kHz Ba Lo hz to 750 Hz Buffered output Acceleration 100 mV g ELECTRICAL Power Two wire loop power 22 Vdc to 36 Vdc Maximum load see note maximum load resistance calculations for specific requirements Up to 600 Ohms resistive Grounding Case isolated aKF k CMSS 420VT SKF C PN CMSS 420VT SN 06724 ay lt cE A ENVIRONMENTAL Operating temperature 20 C to 80 C 4 F to 176 F Sealed Epoxy encapsulated Enclosure SS NEMA 4 4X 12 Mounting Stud mounted Weight without display 227 g 8 oz REGULATORY APPROVAL CE
39. ral mechanical inspection The Inspector 400 ultrasonic probe can detect the early stage of a machine s mechanical malfunction NASA research has demonstrated that ultrasound monitoring will locate potential bearing deficiencies before they are detected by the traditional heat and vibration methods With the Inspector 400 users hear the sound quality of a bearing as well as monitor amplitude changes on the meter This complements other monitoring instruments and adds to the ability to trend troubleshoot and confirm potential bearing problems General mechanical inspection is easy with the Inspector 400 and with very little training users can learn to test bearings within minutes Current vibration programs can achieve enhanced diagnostic ability with the Inspector 400 Prevent over lubrication with the Inspector 400 by simply lubricating only until the meter reaches a specified level Over lubrication is one of the more common causes of bearing failure General mechanical inspection of pumps motors compressors gears and gear boxes All types of operating equipment may be inspected with the Inspector 400 Since the Inspector 400 works in a high frequency short wave environment problems such as cavitation in pumps compressor valve leakage or missing gear teeth may be heard and isolated Reciprocating compressor valve analysis has also become successful with the Inspector 400 and therefore many engine analyzer companies now offer
40. ro In on the problem SKF Reliability Systems standard product catalogue www skf com cm 24 SKF MicroVibe P CMVL 3850 ML Store and recall measurements for trending and analysis The MicroVibe P s data storage capacity is also extraordinarily Impressive It can store up to 2 000 overall vibration signals 1 000 FFT spectrums or 200 records of time waveform data for later recall A search function retrieves specific measurement points and a repeat measurement let s you recall and repeat any measurement for more focused analysis or trending of a potential problem Finally a recall data storage list helps you keep track of and reference all collected data Data management and software for your desktop computer The MicroVibe P offers added functionality Including a software program to extract save edit and display collected data It s ideal for small route data collection 3 lM point2 H GF Point3 A Plank 421205 x 4 Microvibe P Point List Equipment f Planti EM Machine i tie For further analysis and trending data may be uploaded Machines to your desktop computer using a the Data Management software Once uploaded vibration data overall trends and spectra can be stored trended graphically displayed and even exported to Excel Utilities add value Several exciting utilities help make the MicroVibe P an universal tool for machine vibration analysis for any le
41. system CMMS providing enhanced awareness to maintenance management x atex CE ATEX APPROVED The SKF Machine Condition Detector Pro IS MCD Pro IS provides for velocity enveloped acceleration and temperature monitoring with general alarm capabilities and has ATEX Certifications Vibration monitoring When performing measurements the MCD Pro IS s sensor Input signal is processed to produce two vibration measurements for each measurement POINT Velocity vibration identifies phenomena which are observable in the low to mid frequency range and indicates such structural problems as misalignment unbalance mechanical looseness and more However events which occur in the higher frequency ranges such as bearing and gear problems can also be detected by the MCD Pro IS with its Acceleration Enveloping capability a Signal processing technique which focuses on enhancing the repetitious vibration signals that characterize such problems Temperature Temperature measurements enhance the early warning benefit of the instrument by offering a useful indication of mechanical condition or the load applied to a specific component since as a bearing or its lubrication fails friction causes its temperature to rise SKF Reliability Systems standard product catalogue www skf com cm 20 SKF Machine Condition Detector Pro IS CMVL 3600 IS General alarm capabilities When used as a stand alone tool the Machine Cond
42. t criteria based on ISO vibration severity standard and SKF bearing evaluation The SKF MicroVibe P system FFT Spectrum analysis enables user to pinpoint problems like unbalance misalignment bearing rubs etc Multi point automation e Standard vibration measurements Envelope acceleration acceleration velocity displacement time waveform and FFT spectrum analysis e Store and recall measurements For trending and analysis store up to 2 000 overall vibration signals 1 000 FFT spectrum and 200 time waveforms e Data management software Enables users to transfer machinery vibration data to a computer for trending and further analysis e MicroVibe P kit includes MicroVibe P module data management software accelerometer and cable magnetic base earphones user manual and carrying case everything but the PDA An advanced instrument for simplified vibration assessment The MicroVibe P collects and displays overall vibration readings and automatically provides expert judgment of the measured velocity and overall enveloped acceleration levels enabling immediate accurate and reliable assessment of machine or bearing condition SKF MicroVibe P CMVL 3850 ML Multi point automation saves time and improves reliability Automatically collect the ti most useful measurements for vibration analysis DataNo 1 acceleration velocity en ane gee i Micro ibe P Lv 12 26
43. the same temperature as the material underneath it Measure the temperature of the tape or painted surface SKF Temperature Probe CMSS 2000 SL Display User interface display A Backlight On symbol B C F symbol C High Alarm and Low Alarm symbol D Temperature values for the MAX MIN DIF AVG HAL high alarm LAL low alarm and logged temperatures E Symbols for MAX MIN DIF AVG HAL LAL PRB F LOG icon shows log Mode for data storage G Current temperature value H SCAN or HOLD Emissivity symbol and value J Low Battery Lock and Laser On symbols Buttons 1 SET button for setting high and low alarm 2 Up and Down buttons 3 MODE button for cycling through the Mode loop 4 Laser Backlight on off button pull trigger and press button to activate laser backlight 5 LOG button for storing data In SCAN mode the LCD displays both the current temperature G and selected Mode function D E in C F B The unit will HOLD the last reading for 7 seconds after the trigger is released the word HOLD appears H When the battery is low the battery icon Is displayed but the unit will continue to function when the battery is dead the display will be blank and the unit will no longer function To activate the laser and backlight pull the trigger Press the laser backlight button 4 once to activate the backlight twice to turn both laser and backlight on and a third time to
44. trasonic frequency all types of valves even in noisy environments can be accurately tested Valve stems Valve stems may be quickly tested for leaks to atmosphere CE Y 2 P i la e Ai h r s 1 Ly 1 Steam trap inspection Major steam trap manufacturers have recommended ultra sound inspection of steam traps as one of the most reliable methods available By converting the ultrasonic elements of a working steam trap into the audible range the Inspector 400 allows users to hear through headphones and see on a meter the exact condition of a steam trap while it is on line Blowby machine gunning oversized traps or line blockage are all easily detected The Inspector 400 markedly reduces confusion from extraneous sounds or from heat transfer even when traps are extremely close together Electrical inspection Arcing and corona discharge emit ultra sounds at the site of emission This electrical discharge can be located quickly by scanning the area with the Inspector 400 The signal is heard as a frying or buzzing sound in the headset As with pressure or vacuum leak detection the closer the instrument Is to the discharge the more intense the signal Test switch gear transformers circuit breakers buss bars relays junction boxes insulators and other electrical gear SKF Reliability Systems standard product catalogue www skf com cm gt SKF Inspector 400 Ultrasonic Probe CMIN 400 K Gene
45. turn them off How it works Infrared thermometers measure the surface temperature of an Opaque object The unit s optics sense emitted reflected and transmitted energy which is collected Target and focused onto a detector The units electronics translate the information into a temperature reading which is displayed on the unit The laser is used for aiming purposes only Transmitted Energy Measuring temperature Units measure the surface temperature of objects To measure temperature pull and hold the trigger while pointing at the target to be measured See distance and spot size A temperature reading appears on the display If the thermometer Is subject to large changes in ambient temperatures hot to cold or cold to hot allow 30 minutes for temperature stabilization before taking measurements to ensure accuracy Storing data The thermometer is capable of storing up to 12 data locations The infrared temperature temperature unit C or F and emissivity are also stored Distance and spot size To achieve an accurate temperature reading unit must be the correct distance from the targeted object A singular laser spot highlights the approximate 24mm 30mm 62mm center of the spot measurement 300mm 900mm 1500mm area This spot E i D S 30 1 measurement area gets larger the farther away you are from the target The ratio r 09 12 25 of the Distance E 12 36 60 to Spot Size
46. us other industries Non contact thermometer uses Electrical industrial ae Automotive and diesel a Ra Food safety SKF Reliability Systems standard product catalogue www skf com cm 14 SKF Micro lemp Non contact Thermometer CMSS 2020 SL Details Measuring To measure a temperature point MicroTemp Non contact Thermometer at object and pull the trigger Be sure to consider distance to spot size ratio and field of view The laser is only used for aiming Display The backlit LCD displays the current temperature in Celsius or Fahrenheit The unit will hold the reading for 7 seconds after the trigger Is released the word HOLD appears The presence of the battery icon indicates a low battery B Usage The handle pulls open by using the finger indents This provides access to the unit switch A for Celsius or Fahrenheit selection It also provides access to insert or remove the 9 Volt battery Specifications Order information Recommended target ranges The unit s distance to target spot size ratio e CMSS 2020 SL MicroTemp Non contact Thermometer is 6 1 For best results make sure the target is larger than the unit s spot including multi lingual user manual English French size l l l German Portuguese and Spanish 9 V alkaline battery Temperature range 18 C to 260 C 0 to 500 F Accuracy For targets at Optional kits that includes the CMSS 2020 SL 1 C to 260
47. vel of expertise Collect data in english or metric units or reference a dictionary of vibration terminology Poinki t FF SKF s new MicroVibe P truly brings you vibration monitoring and analysis power without complexity It s tomorrow s big solution for vibration analysis in a small smart package and its available today Get more information at www skf com cm Specifications MicroVibe P CMVL 3850 ML Minimum PDA requirements Conforms to the Pocket PC specifications Operating system Microsoft Windows Mobile 3 0 5 0 Processor ARM processor Interface Compact Flash TYPE II Slot 3 3 V only Recommended specifications Processor PXA255 400 MHz or higher Memory RAM 64 MB or higher Interface with Pocket PC Compact Flash TYPE Il slot 3 3 V only Power supply 3 3 V supplied by Pocket PC Current Standby 44 u A Under measurement 48 mA Pickup input PU IN AC voltage signal Maximum 2 5 V Input terminal 8 pin modular jack RJ 45 ICP type pre amp built in accelerometer is not connected Raw waveform output PU OUT AC voltage signal Maximum 2 5 V Output terminal Mini jack 2 5 mm Sampling frequency Maximum 76 8 kHz changes according to mode 76 8 kHz 38 4 kHz Aliasing filter 20 kHz 2 kHz changes according to mode and sampling frequency A D 16 Bit Temperature range O to 45 C 32 F to 113 F Humidity range lt 90 relative humidity non con
48. vity selection low battery indicator e Scanning module e Rubber focusing probe e Stethoscope module e Lightweight foam lined headset e 9 volt alkaline battery replaceable e Cordura nylon soft pack carrying case e Comprehensive instruction manual English language Specifications Construction Hand held ABS pistol type ultrasonic processor stainless steel sensor enclosures Circuitry SMD solid state hybrid heterodyne receiver Frequency response 20 100 kHz centered at 38 42 kHz Indicator 10 segment LED bar graph red Sensitivity selection 8 position precision attenuation Power 9 volt alkaline battery Low battery voltage indicator LED Headset Lightweight foam lined double headset wired monophonic impedance 16 ohms Probes Scanning module stainless steel unisonic single transducer piezoelectric crystal type stethoscope contact module stainless steel plug in type with 5 5 stainless steel waveguide Rubber focusing probe Shields stray ultrasonic signals and focuses detected signals Response time 300 millisec Ambient operating temperature range 0 C to 50 C 32 F to 120 F Relative humidity 10 to 95 noncondensing at up to 30 C 86 F Storage temperature 18 C to 54 C 0 F to 130 F Dimensions Height 133 mm 5 25 Width 50mm 2 00 Length 203 mm 8 00 Weight 320 g 11 oz Carrying case Cordura nylon soft pack with die cut foam Ordering informatio

SKF Reliability Systems standard product catalogue

Contents

Download Pdf Manuals

Related Search

Related Contents