Home

* I User`s Manual

image

Contents

1. range from 1 to 9999 F ADD The counter may add up the counting result each time at this mode Only when taking away the banknote from stacker and pressing the reset key to clear up the result the counter can start counting from zero and accumulating again Note For 3 digit counting display the accumulating range is within 999 and for 4 digit counting display range within 9999 Clear up the banknote and sort as per par value clear away stains on banknote and spread properly and feed onto hopper for counting For the 3a User s Manual bundled banknote please loosen first and spread out properly before feeding onto hopper See the illustration Fig 1 the proper way to feed banknote Fig 2 and Fig 3 improper ways Fig 2 shows that the operator forgets to keep banknotes spreading properly and Fig 3 shows that the operator spreads the banknotes improperly Proper way to feed banknote Improper way Improper way When banknote feeding is not desirable please adjust the gap between drag rubber and feeding wheel through the screw on the hopper After adjusting test the tension by feeding one piece of banknote between drag rubber and feeding wheel Better to keep the tension at 2Kg after adjustment Clockwise to fasten Anti clockwise to loosen D 7 1 Please change the drag rubber when its worn out Unscrew the adjusting screw take out the banknote stand and press the hopper board to take apart and
2. then take away the worn rubber to change a new one 7 2 Please change the feeding wheel when it s worn out otherwise the feeding and counting may not be desirable Take out the banknote stand and take apart plastic shield at both sides use long nose pliers to take out the snap ring on the feeding shaft for loosening the shaft and then take away the worn feeding wheel to change a new one 4 User s Manual 8 1 Common Trouble amp Solution Trouble Cause Solution 1 Infrared targeting tube 1 Keep aligned with infrared 2 Dust covered on infrared 2 Clear away dust eco fo not good 2 Dust covered on infrared 2 Clear away dust aoe e Reset Key not functional Key broken 2 Connection Change connect ee ad automatically _Motor not work motor 2 starting capacitor of 2 Change ee Sa 3 Motor burn out or 3 Change Driven wheel not run Transmission belt broken Change nome ewe fe Noise from driven wheel Driven wheel not fastened Keep the wheel close to Not work after switching or not close to bearing so bearing and fasten the screw as to make bearing sliding User s Manual 8 2 Code displayed after self diagnosis amp Solution Trouble Code Trouble Position Solution Clear away dust and other Clear away dust and other C 5 Speed Sensor Clear away dust and other impurities eS a hd 7 es Banknote Sandwiched 8 3 Alarm
3. Bill Counter Thanks for Use User s Manual Precaution For your personal safety please use only the socket with grounding connection Be sure the power supply complies with the specific limit 1 A Counting Speed gt 1000pcs min B Hopper amp Stacker Capacity gt 130pcs C Banknote Size Max 90x 175mm Min 50x 100mm D Counting Display Range 1 999pcs 1 9999pcs E Preset Display Range 1 999pcs 1 9999pcs F Power Supply 220V 1410 60Hz 110V 1 10 60Hz G Max Working Current 0 5A H Ambient Temperature 0 40 C I Relative Humidity 40 90 J Noise lt 60dB K Power Consumption 60W L Weight 8kg perate Plug the cord into the right power supply socket If your counter has the 2 outer display please plug to connect well After switching on better in performance to keep it set up running for one minute your counter will start self diagnosis and then enter MG 1 UV working mode when no trouble is detected Now only feed banknote to keep it working When some code appears in display please refer to the chapter of Common Trouble amp Solution to solve the problem before normal working Select the working mode of MG 1 MG 2 Counting and UV 1 When the panel features the key of Function press the key to select the e User s Manual working modes of MG2 Counting and MG1 in circle and the responding indicator will be on 2 When the panel feat
4. ing Code Co E 6 Consumabies T We reserve the right to make technical modification without prior notice 6
5. top shield use a brush to clear away the dust Be sure to cut off the power supply before cleaning 3 6 Keep the counter well grounded earth wire as the counter may produce static charge in use Don t store the counter in a wet place which may cause electric shock 3 7 Be sure to cut off the power supply while the counter is not in use for a long time or without operator s care F User s Manual 3 8 Please cut off the power supply and contact maintenance worker for repair services in case that the below case happens A Heavily broken due to falling B Not work even by following the operation instructions C Function abnormal D Liquid splashed onto the counter A MG1 For counting and detecting the banknote that s low in magnetism B MG 2 For counting and detecting banknote that s strong in magnetism like US dollars C Counting For counting and spectrum detecting banknote that s without magnetism D Counting For UV detecting generally keep the function on while counting E Preset Press the preset button to activate the function Now press or button to preset the counting batch as required The counter will stop automatically while completing the setup pieces and starting again after taking away the banknote from stacker Press the Select key to cancel the function Note For 3 digit counting display the preset range is from 1 to 999 and for 4 digit counting display
6. ures the keys of MG and Counting press the MG key to select the working mode of MG1 or MG2 in circle and press the Counting key to enter working mode of Counting directly and shut off the MG detecting function synchronously 3 When the panel features no key of UV the machine keeps the UV detecting function on aiways when the panel features the key of UV please press the key to keep the function on or off Select the working mode of Preset and ACCUM in the standby state 4 Press the Select key to keep Preset and ACCUM mode on in circle and the responding indicator will be on 3 power supply AC220V 410 60HZ and optional for AC110V 410 50Hz Be sure to cut off power supply and unplug the cord before disassembling or stopping for a time 3 2 Keep far away from some electric appliances e g cell phone or welder that can cause interference on power supply while using Avoid direct strong light or magnetic field otherwise the counter may not work desirably 3 3 Protect feeding wheel driven wheel drag rubber against touching with grease otherwise the feeding wheel may be sliding to cause counting error 3 4 In case of sudden failure of power supply please switch on again after at least 5 seconds otherwise the counter may not work normally 3 5 Completely clean counting tube and sensors once every week Only take part the

Download Pdf Manuals

image

Related Search

Related Contents

Samsung HT-TX25T Manual de Usuario    Graide Color Match User Manual  Piège à polypes  

Copyright © All rights reserved.
Failed to retrieve file