HG654440SM IE GB EN GAS HOB USER MANUAL
Contents
1. with vents to let a continuous supply of air The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit MANUFACTURER ELECTROLUX ITALIA S p A C so Lino Zanussi 30 33080 PORCIA PN ITALIA A A gt gt 2 77 gt 20 em P 0 4 P 4 El a le cm cm PRODUCT DESCRIPTION Cooking surface layout CX Cooktop Semi rapid burner Triple Crown burner Auxiliary burner Control knobs 0000 Control knobs H e no gas supply off position pa ignition position maximum gas supply minimum gas supply Operation OPERATION Ignition of the burner MN WARNING Be very careful when you use open fire in kitchen environment Manufacturer decline any responsibility in case misuse of the flame i Always light the burner before you put cookware To light the burner 1 Turn the control knob counterclockwise to the maximum position X and push it down 2 Keep the control knob pushed for approximately 5 seconds this will let thermocouple to warm up If not the gas supply will be interrupted 3 Adjust the flame after it is regular If after some tries the burner does not light check if the crown and its cap are in correct positions Each control knob has a pilot light It lights up when2. Be careful they do not come in touch with mobile parts or they are not squeezed Also be careful when the hob is put together with an oven It is important to install the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe Failure to ensure the correct assembly will cause leakage of gas Make sure that the gas supply pressure of the appliance obeys the recommended values Rigid connection Carry out connection by using metal rigid pipes copper with mechanical end Injectors replacement 1 Remove the pan supports 2 Remove the caps and crowns of the burner 3 With a socket spanner 7 remove the injectors and replace them with the ones which are necessary for the type of gas you use see table in Technical Data section 4 Assemble the parts follow the same procedure backwards 5 Replace the rating plate it is near the gas supply pipe with the one for the new type of gas supply You can find this plate in the package supplied with the appliance If the supply gas pressure is changeable or different from the necessary pressure you must fit an applicable pressure adjuster on the gas supply pipe Adjustment of minimum level To adjust the minimum level of the burners Installation GE 1 Light the burner 2 Turn the knob on the minimum position 3 Remove the knob 4 With a thin screwdriver adjust the by pass screw position lt The by pass screw f you ch
3. make the terminal become too hot A qualified electrician must install the clamping connections correctly Use a strain relief clamp on cable Use the correct mains connection cable and replace the damaged mains cable with ap plicable cable Speak to your local Service Force Centre The appliance must have the electrical installation which lets you disconnect the appli ance from the mains at all poles with a contact opening width of minimum 3 mm If the fixing bracket is near to the terminal block always make sure the connection cable does not come in contact with the edge of the bracket You must have correct isolation devices line protecting cut outs fuses screw type fuses removed from the holder ground leakage trips and contactors Disposal of the appliance To prevent the risk of physical injury or damage Disconnect the appliance from the power supply Cut off the mains cable where it connects with the appliance and discard it Flat the external gas pipes if there are fitted Speak to your local authorised facilities for disposal of your appliance INSTALLATION WARNING The following instructions about installation connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force Installation Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and Use Regula tions Current Edition a
4. mm Heat input Triple Crown burner 4 0 kW Semi rapid burner 2 0 kW Auxiliary burner 1 0 kW TOTAL POWER G20 2H 20 mbar 9 kW G30 3 28 30 mbar 654 g h G31 3 37 mbar 643 g h Environment concerns EEE Electric supply 230 V 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse Gas connection G Ja Category 112H3 Gas supply G20 2H 20 mbar Appliance class S By pass diameters Auxiliary 28 Semi rapid 32 Triple Crown 56 Gas burners NORMAL POWER NORMAL REDUCED LPG POWER POWER NATURAL GAS Butane Propane 630 631 3 G20 2H 20 mbar 28 30 37 mbar BURNER inj 1 100 mm ADE 1 0 0 33 70 0 095 50 73 71 burner Semi tap 20 0 45 96 0 190 71 145 143 id burner Triple Crown 40 1 4 146 0 381 98 291 286 burner ENVIRONMENT CONCERNS The symbol X on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the produ
5. the liquid starts to boil turn down the flame to barely simmer the liquid Care and cleaning IN WARNING Use pots and pans with diameter applicable to the dimension of burner Do not use cooking vessels on the hotplate that overlap its edges Triple Crown 180 260 mm Front Semi rapid 120 180 mm Rear Semi rapid 120 220 mm Auxiliary 80 160 mm WARNING Pots must not enter the control zone IN WARNING Make sure pot handles do not protrude over the front edge of the cooktop and that pots are centrally positioned on the rings in order to achieve maximum stability and to obtain lower gas consumption Do not place unstable or deformed pots on the rings to prevent from spill and injury IN WARNING Flame diffuser are not recommended Information on acrylamides Important According to the newest scientific knowledge if you brown food specially the one which contains starch acrylamides can pose a health risk Thus we recommend that you cook at the lowest temperatures and do not brown food too much CARE AND CLEANING AN WARNING Switch the appliance off and let it cool down before you clean it Disconnect the appliance from the electrical supply before carrying out any cleaning or maintenance work WARNING For safety reasons do not clean the appliance with steam cleaners or high pressure clean ers A A WARNING 1 Do not use abrasive cleaners steel wool pads or acids they can cause damage to the a
6. HG654440SM EN GAS HOB USER MANUAL FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler features you might not find on ordinary appliances Please spend a few minutes reading to get the very best from it ACCESSORIES AND CONSUMABLES In the AEG webshop you ll find everything you need to keep all your AEG appliances looking spotless and working perfectly Along with a wide range of accessories designed and built to the high quality standards you would expect from specialist cookware to cutlery baskets from bottle holders to delicate laundry bags Visit the webshop at www aeg com shop Contents CONTENTS 4 Safety information 6 Installation 12 Product description 13 Operation 14 Helpful hints and tips 15 Care and cleaning 17 What to do if 18 Technical data 19 Environment concerns The following symbols are used in this user manual A Important information concerning your personal safety and information on how to avoid damaging the appliance i General information and tips Environmental information Subject to change without notice Safety information N SAFETY INFORMATION IN WARNING These instructions are only valid in the countries whose symbols appear on this booklet s cover 1 For your s
7. afety and correct operation of the appliance read this manual carefully before installation and use Always keep these instructions with the appliance even if you move or sell it Users must fully know the operation and safety features of the appliance General safety N WARNING Persons including children with reduced physical sensory mental capabilities or lack of ex perience and knowledge must not use the appliance They must have supervision or instruc tion for the operation of the appliance by a person responsible for their safety Child safety Use Only adults can use this appliance Children must get supervision to make sure that they do not play with the appliance Keep all packaging away from children There is a risk of suffocation and physical injury Keep children away from the appliance during and after the operation until the appli ance is cold Remove all packaging stickers and the protective layer of the stainless steel hob panel if present from the appliance before first use Do not remove the rating plate It can inva lidate the guarantee Set the cooking zones to the off position after each use Burners and accessible part become hot during and after use Do not put cutlery or sau cepan lids on the cooking surface Cookware and its contents can tip over There is the risk of burns Too hot fats and oils can ignite very quickly There is the risk of fire Do not leave the appliance unattended duri
8. ange from natural gas 20 mbar to liquid gas fully tighten the by pass screw in f you change from liquid gas to natural gas 20 mbar undo the by pass screw proximately 1 4 of a turn 1 2 of a turn for Triple Crown burner WARNING Make sure the flame does not go out when you quickly turn the knob from the maximum position to the minimum position Electrical connection Electrical Requirements Any electrical work required to install this hob should be carried out by a qualified elec trician or competent person in accordance with the current regulations THIS HOB MUST BE EARTHED Always use a correctly installed shockproof socket Make sure that there is an access to the mains plug after installation Do not pull the mains cable to disconnect the appliance Always pull the mains plug The appliance must not be connected with an extension cable an adapter or a multiple connection risk of fire Check that the ground connection is in conformity with the standard and regulations force The power cable must be placed in such a way that it does not touch any hot part Connect the appliance to the mains with a device that lets to disconnect the appliance from the mains at all poles with a contact opening width of minimum 3 mm eg auto matic line protecting cut out earth leakage trips or fuse None of a parts of the connection cable can not get a temperature 90 C Any permanent electrical installation must comply with the lates
9. ct Packaging material The packaging materials are friendly to the environment and can be recycled The plastic components are identified by marking gt PE lt gt PS lt etc Discard the packaging materials as household waste at the waste disposal facilities in your municipality www aeg com shop 397201901 B 052011 Ps RE le 3 PE ce
10. face of hob 2 Clean the appliance with a damp cloth and some detergent 3 At the end rub the appliance dry with a clean cloth To make burners work properly make sure that pan supports are placed in the way that the arms are centred upon the burner 1 In order to avoid damaging the hob top pay attention when replacing the pan support A A O Y Cleaning of the spark plug This feature is obtained through a ceramic ignition candle with a metal electrode Keep these components well clean to prevent difficult lighting and check that the burner crown holes are not obstructed Periodic maintenance Periodically speak your local Service Force Centre to check the conditions of the gas supply pipe and the pressure adjuster if fitted What to do if WHAT TO DO IF There is no spark when lighting There is no electrical supply Make sure that the unit is the gas connected and the electrical supply is switched on e Control the fuse If the fuse is released more than one time refer to a qualified electrician e Burner cap and crown are Make sure that the burner placed uneven cap and crown are in correct positions The flame is blow out immedi e Thermocouple is not heated e After lightning the flame ately after ignition sufficient keep the knob pushed for approximately 5 seconds The gas ring burns unevenly e Burner crown is blocked e Make sure that t
11. h the edges of the hob is 400 mm If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob For appliances installed in the Republic of Ireland please refer to NSAI Domestic Gas Instal lation 1 5 813 Current Edition Section 7 Permitted Locations of Appliance Gas Connection WARNING Any gas installation must be carried out by a GAS SAFE REGISTER installer Make sure that once the hob is installed it is easily accessible for the engineer in the event of a breakdown The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored On the end of the shaft which includes the G 1 2 threaded elbow adjustment is fixed so that the washer is fitted between the components as shown in the diagram Screw the parts together without using excessive force EE installation p pe p End of shaft with nut IS Q a Washer Elbow Connection to the gas supply should be with either rigid or semi rigid pipe i e steel or cop per The connection should be suitable for connecting to R 1 2 1 2 BSP male thread When the final connection has been made it is essential that a thorough leak test is carried out on the hob and installation Make sure that the main connection pipe does not exert any strain on the hob If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards
12. he injector with food residues is not blocked and the burn er crown is clear of food particles If there is a fault first try to find a solution to the problem yourself If you cannot find a solution to the problem yourself speak your dealer or the local Service Force Centre 1 If you operated the appliance incorrectly or the installation was not carried out by a regis tered engineer the visit from the customer service technician or dealer may not take place free of charge even during the warranty period Labels supplied with the accessories bag Stick the adhesive labels as indicated below Technical data T MOD TYPE PROD NO 230V 50Hz PROD NO PROD NO C 0049 SER NO 20 SER NO SER NO nai DATA DATA MADE IN ITALY D 1 1 z one X X Stick it on Guarantee Card and send this part Stick it on Guarantee Card and keep this part Stick it on instruction booklet These data are necessary to help you quickly and correctly These data are available on the supplied rating plate e Model description e Product number PNC e Serial Number S N Use the original spare parts only They are available at Service Force Centre and approved spare parts shops TECHNICAL DATA Hob dimensions Width 594 mm Length 510 mm Hob recess dimensions Width 560 mm Length 480
13. nd the IEE Wiring Regulations Current Edition For appliances installed in the Republic of Ireland please refer to NSAI Domestic Gas Instal lation 1 5 813 Current Editions and the Rules for Electrical Installations Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Prac tice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions The hob should not be installed in a bed sitting room with a volume of less than 20 m3 If it is installed in a room of volume less than 5 m3 an air vent of effective area of 100 cm is required If it is installed in a room of volume between 5 m3 and 10 3 an air vent of effec tive area of 50 cm is required while if the volume exceeds 11 m3 no air vent is required However if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m3 If there are other fuel burning appliances in the same room B S 5440 Part 2 Current Edi tion should be consulted to determine the requisite air vent requirements For appliances installed in the Republic of Ireland please refer to the NSAI Domestic Gas Installation 1 5 813 Current Editions Table Four Location The hob may be located in a kitchen a kitchen diner or bed sitting room with a volume greater than 20 m3 but not in a bathroom or shower room The minimum distance combustible material can be fitted above the hob in line wit
14. ng operation Always monitor the appliance during operation Do not let the liquids overflow into the holes of the top of the hob Do not use the hob without cookware The appliance is only for domestic use Do not use the appliance for commercial and in dustrial use Only use the appliance for domestic cooking tasks This is to prevent physical injury to persons or prevent damage to property Use only cookware with diameter applicable to the dimensions of burners There is a risk of overheating and rupture of the glass plate if applicable Do not use a pan with diameter smaller than burner dimension flames will heat up the pan handle Safety information Pots must not enter the control zone Do not use not stable cookware to prevent from tilt and accident Do not put flammable products or items that are wet with flammable products and or fusible objects made of plastic or aluminium and or fabrics in near or on the appliance There is the risk of explosion or fire Use only the accessories supplied with appliance Be careful when you connect the appliance to the near sockets Do not let electricity bonds touch the appliance or hot cookware Do not let electricity bonds tangle Installation You must read these instructions The manufacturer is not responsible for any injury to persons and pets or damage to property caused by failure to obey these require ments To prevent the risks of structural damage or physical i
15. njury installation connection of the appliance to the power supply and gas system setting up and maintenance must only be done by qualified personnel in compliance with standards and local regulation force Make sure that the appliance is not damaged because of transport Do not connect a damaged appliance If it is necessary speak to the supplier Only use built in appliances after you assemble the appliance into correct built in units and work surfaces that obey the standards Do not install the hob over a domestic appliances if the installation instructions do not allow it Install the appliance only on a worktop with flat surface Do not change the specifications or modify this product There is the risk of injury and damage to the appliance Fully obey the laws ordinances directives and standards in force in the country where you use the appliance safety regulations recycling regulations electrical safety rules etc Keep the minimum distances to other appliances and units Install anti shock protection for example install the drawers only with a protective panel directly below the appliance Prevent damage of the cut surfaces of the worktop against moisture with a correct seal ant Seal the appliance to the worktop with no space left with a correct sealant Prevent damage to the bottom of the appliance from steam and moisture e g from a dishwasher or oven Do not install the appliance adjacent to doors and below windows H
16. ot cookware can be hit off the hob when you open the doors or windows Before installation make sure that the local supply conditions gas type and pressure agree with the adjustment of appliance The adjustment conditions for the appliance are on the rating plate which you can find near the gas supply pipe BE installation This appliance is not connected to a combustion products evacuation device It must be installed and connected in accordance with current installation regulations Particular attention must be given to the relevant requirements regarding ventilation The use of a gas cooking appliance cause heat and moisture in the room in which it is installed Make sure that the ventilation in the kitchen is good keep natural venti lation holes open or install a mechanical ventilation device mechanical extractor hood More ventilation for example opening of a window or increasing the level of me chanical ventilation where present is necessary when you operate the appliance with intensity for a long time Carefully obey the instructions for electrical connections There is the risk of injury from electrical current Disconnect the appliance from the electrical supply before you do the maintenance work or you clean it The electrical mains terminal is live Make electrical mains terminal free of voltage Install correctly to give anti shock protection A loose and incorrect mains plug and socket connections can
17. ppli ance Scratches or dark stains on the glass have no effect on how the appliance operates e You can remove the pan supports to easily clean the hob e To clean the enamelled parts cap and crown wash it with warm soapy water and dry it carefully before you put them back MIA Care and cleaning Stainless steel parts wash with water and then dry with a soft cloth The pan supports are not dishwasher proof they must be washed by hand e When you wash the pan supports by hand take care when you dry them as the enamel ling process occasionally leaves rough edges If necessary remove stubborn stains using a paste cleaner Make sure you position the pan supports correctly after cleaning e To make burners work correctly make sure that the arms of the pan supports are in the centre of the burner Be very careful when you replace the pan supports to prevent the hob top from damage After cleaning dry the appliance with a soft cloth The stainless steel can become tarnished if it is too much heated Refer to this you must not cook with potstones earthenware pans or cast iron plates Do not use aluminium foil to prevent damage the top during operation Removing the dirt 1 Remove immediately melting plastic plastic foil and food containing sugar Stop the appliance and let it cool down before you clean limescale rings water rings fat stains shiny metallic discolorations Use a special cleaner applicable for sur
18. t E E Regulations and lo cal Electricity Board regulations For your own safety this should be undertaken by a quali fied electrician e g your local Electricity Board or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting NICEIC The manufacturer declines any liability should these safety measures not be observed MIA Installation A A This hob is designed to be connected to a 230 V 50 Hz AC electrical supply Before switching on make sure the electricity supply voltage is the same as that indicated on the hob rating plate The rating plate is located on the bottom of the hob The hob is supplied with a 3 core flexible supply cord incorporating a 3 amp plug fitted In the event of having to change the fuse a 3 amp ASTA approved BS 1362 fuse must be used Green and Yellow 3 amp fuse Brown Cord clamp Blue Should the plug need to be replaced for any reason the wires in the mains lead are col oured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live 1 Connect the green and yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow 2 Connect the blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black 3 Connect the brown live wire to the terminal in the plug which is marked
19. with the let ter L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely The replacement of electric cable must be carried out exclusively by the service force centre or by personnel with similar competencies in accordance with the current regulations Installation Replacement of the connection cable To replace the connection cable use only HO5V2V2 FT9O or equivalent type Make sure that the cable section is applicable to the voltage and the working temperature The yellow green earth wire must be approximately 2 cm longer than the brown or black phase wire Building In min 600 mm gt gt y min 450 mm min 650 mm y 3 mm 11 mm A supplied seal A supplied seal B supplied brackets Possibilities for insertion Kitchen unit with door The panel installed below the hob must be easy to remove and let an easy access in case a technical assistance intervention is necessary 30 mm mm 20 mm max 150 mm a Removable panel Product description b Space for connections Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped
20. you turn the control knob Helpful hints and tips Burner cap Burner crown Ignition candle Thermocouple WARNING Do not keep the control knob pushed for more than 15 seconds If the burner does not light after 15 seconds release the control knob turn it into off posi tion and try to light the burner again after minimum 1 minute In the absence of electricity you can ignite the burner without electrical device in this case approach the burner with a flame push the relevant knob down and turn it counter clock wise to maximum gas release position If the burner accidentally goes out turn the control knob to the off position and try to light the burner again after minimum 1 minute E El gt The spark generator can start automatically when you switch on the mains after installa tion or a power cut It is normal Turning the burner off To put the flame out turn the knob to the symbol e WARNING Always turn the flame down or switch it off before you remove the pans of the burner Using the Wok Stand A wok stand lets you to use a rounded bottom wok on the hob Do not use the wok stand with any other type of wok or pan You must only use the wok stand on the Triple Crown When you install the wok stand make sure that the recesses in the frame fit on the bars of the pan supports HELPFUL HINTS AND TIPS Energy savings f possible always put the lids on the pans e When
Download Pdf Manuals
Related Search