8-Port 10/100/1000Mbps Gigabit Ethernet Switch GSD
Contents
1. e Gigabit Ethernet Switch x 1 e User s manual x 1 e Power cord x 1 e Rubber feet x 4 If any of these are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 How to Use This Manual This Gigabit Ethernet Switch User Manual is structured as follows Chapter 2 Installation The chapter explains the feature functionality and the physical installation of the Gigabit Ethernet Switch Chapter 3 Switch operation The chapter explains the Gigabit Ethernet Switch transmit operation Chapter 4 Troubleshooting The chapter explains the troubleshooting of the Gigabit Ethernet Switch Appendix A This chapter contains cable information of the Gigabit Ethernet Switch 46 1 3 Product Features Comply with IEEE 802 3 10Base T IEEE 802 3u 100Base TX IEEE 802 3ab 1000Base T Ethernet standard 8 Port 10 100 1000Mbps Gigabit Ethernet ports Features Store and Forward mode with wire speed filtering and forwarding rates Hardware based 10 100Mbps half full duplex and 1000Mbps full duplex mode flow control and auto negotiation IEEE 802 3x flow control for full duplex operation and Back pressure for half duplex operation Integrated address look up engine support 4K absolute MAC addresses 1Mbit on chip frame buffer 9K Jumbo packet suppor2. device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic 1 equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET 8 Port 10 100 1000Mbps Gigabit Ethernet Switch User s Manual For Model GSD 805 Revision 1 0 July 2008 Part No EM GSD805v1 0 2350 A33230 000 TABLE OF CONTENTS T INTRODUCTION 2 22 22 25e pee Drexeutur de ect eat uten qaia Dust cr dna Deae 6 1 1 Package Contents siccscsincsnnnaranu
3. 3 Keep enough ventilation space between the Gigabit Ethernet Switch and the surrounding objects 13 H When choosing a location please keep in mind the environmental restrictions discussed in Chapter 1 Section 1 4 Product Specifications Step 4 Connect your Gigabit Ethernet Switch to network devices A Connect one end of a standard network cable to the 10 100 1000 RJ 45 ports on the Back of the Gigabit Ethernet Switch B Connect the other end of the cable to the network devices such as printer servers workstations or routers etc Connection to the Gigabit Ethernet Switch requires UTP Category 5 network cabling with RJ 45 tips For more information please see the Cabling Specification in Appendix A Step 5 Supply power to the Gigabit Ethernet Switch A Connect one end of the power cable to the Gigabit Ethernet Switch B Connect the power plug of the power cable to a standard wall outlet When the Gigabit Ethernet Switch receives power the Power LED should remain solid Green A 14 3 Switch Operation 3 1 Address Table The Gigabit Ethernet Switch is implemented with an address table This address table composed of many entries Each entry is used to store the address information of some node in network including MAC address port no etc This information comes from the learning process of Gigabit Ethernet Switch 3 2 Learning When one packet comes in from an
4. 8 Port 10 100 1000Mbps Gigabit Ethernet Switch GSD 805 User s Manual Trademarks Copyright PLANET Technology Corp 2008 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital
5. Gigabit Ethernet Switch scans the destination address from the packet header searches the routing table provided for the incoming port and forwards the packet only if required The fast forwarding makes the switch attractive for connecting servers directly to the network thereby increasing throughput and availability However the switch is most commonly used to segment existing hubs which nearly always improves overall performance An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters Due to the learning function of the Gigabit Ethernet Switch the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subsequently used to filter packets whose destination address is on the same segment as the source address This confines network traffic to its respective domain reducing the overall load on the network The Gigabit Ethernet Switch performs Store and Forward therefore no error packets occur More reliably it reduces the re transmission rate No packet loss will occur 7 16 3 5 Auto Negotiation The STP ports on the Gigabit Ethernet Switch have built in Auto negotiation This technology automatically sets the best possible bandwidth when a connection is established with another network device usually at Power On or Reset This is done by
6. detect the modes and speeds at the second of both device is connected and capable of both 10Base T and 100Base TX devices can connect with the port in either Half or Full Duplex mode 1000Base T can be only connected in Full duplex mode 17 1 4 TROUBLESHOOTING This chapter contains information to help you solve issues If the Gigabit Ethernet Switch is not functioning properly make sure the Gigabit Ethernet Switch was set up according to instructions in this manual The per port LED is not lit Solution Check the cable connection of the Gigabit Ethernet Switch Performance is bad Solution Check the speed duplex mode of the partner device The Gigabit Ethernet Switch is run at Auto negotiation mode and if the partner is set to half duplex then the performance will be poor Per port LED is lit but the traffic is irregular Solution Check that the attached device is not set to dedicate full duplex Some devices use a physical or software switch to change duplex modes Auto negotiation may not recognize this type of full duplex setting Why the Gigabit Ethernet Switch doesn t connect to the network Solution Check per port LED on the Gigabit Ethernet Switch Try another port on the Gigabit Ethernet Switch Make sure the cable is installed properly Make sure the cable is the right type Turn off the power After a while turn on power again APPENDIX A NETWORKING CONNECTION A 1 Switch s RJ 45 Pin Ass
7. etevacvansacadsansyadidacdonicasdaned 6 1 2 How to Use This Manual onere eorr nre 6 1 3 Product Features deo eesue e ies onia eeter nios omen s pese iter crean 7 1 4 Product Specifications iuit edi ose uoct ee te Rea E oden eq peor uU uE 8 2 INSTALLATION visia e aas eges chou verde a pee Aae 10 2 1 Product DescrIDEIOD crion ottiene kh rh ra ndn nerui Eun 10 2 1 1 Product OVervi8w c oce eerie nderit nee pn ene nens daes 11 2 1 2 Switchi Front Panel centes spe usen ee eene orspeocises 11 2 1 3 EED IndiCatots iie urere tiene a benc edes 12 2 1 4 Switch Rear Panel decis etae diese sao ai ood 12 2 2 Installing the GWICCH ssion nnie tete eaa dun 13 2 2 1 Desktop Installati n 1 45 rte ra rra rn nr nnns 13 EM ceo uo M CE 15 Bali Address Table eene orte roit ip rese Sopa E utedeadscaapeds 15 3 2 ip m 15 3 3 Forwarding amp Filterilg rici tenin baeo nat h pe kr ree eees 15 3 4 Store arid FOFWeld iieeesee ieu a unas te ree Ure nin enin 6 16 3 5 Auto NegotlabllOPi e decssea sensor pa kit enixa EE x RE bra EAR xal taii 17 4 TROUBLESHOOTING bis scncictssescneparaccaccnstcieesteansonacdaedectodens 18 APPENDIX A NETWORKING CONNECTION een 19 A 1 Switch s RJ 45 Pin Assignments esee 19 A 2 RJ 45 cable Pin Assignments seseeeeene 20 1 INTRODUCTION 1 1 Package Contents Check the contents of your package for following parts
8. ignments 1000Mbps 1000Base T Contact MDI MDI X 1 BI_DA BI_DB 2 BI_DA BI_DB 3 BI_DB BI_DA 4 BI_DC BI_DD 5 BI_DC BI_DD 6 BI_DB BI_DA 7 BI_DD BI_DC 8 BI_DD BI_DC 10 100Mbps 10 100Base TX RJ 45 Connector pin assignment MDI MDI X Contact Media Dependant Media Dependant Interface Interface Cross 1 Tx transmit Rx receive 2 Tx transmit Rx receive 3 Rx receive Tx transmit 4 5 Not used 6 Rx receive Tx transmit 7 8 Not used 19 A 2 RJ 45 cable Pin Assignments The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection Straight Cable SIDE 1 SIDE 2 12345678 SIDE1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 12345678 SIDE2 6 Green 7 White Brown 8 Brown Cross Over Cable SIDE 1 12345678 SIDE1 1 White Orange 3 White Green 4 Blue 12345678 SIDE2 6 Green 7 White Brown 2 Orange 5 White Blue 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 34 20
9. itch 1 10 supported routers and Servers to directly connect to this device for fast reliable data transfer 2 1 1 Product Overview The PLANET Gigabit Ethernet Switch with 8 RJ 45 10 100 1000Mbps ports for high speed network connectivity The Gigabit Ethernet Switch can also automatically identify and determine the correct transmission speed and half full duplex mode of the attached devices with its 8 ports The Gigabit port with 9K jumbo frame feature supported can handle extremely large amounts of data transmission in a secure topology linking to a backbone or high power servers The Gigabit Ethernet Switch also supports Store and Forward forwarding scheme to ensure low latency and high data integrity eliminates unnecessary traffic and relieves congestion on critical network paths With an intelligent address recognition algorithm the Gigabit Ethernet Switch could recognize up to 4K different MAC address and enables filtering and forwarding at full wire speed 2 1 2 Switch Front Panel Figure 2 1 shows a front panel of GSD 805 QPLANET a Port Gigabit Ethernet Switch GSD 805 Figure 2 1 GSD 805 front panel 11 2 1 3 LED Indicators GSD 805 LED Color Function PWR Green Lit indicate the Switch has power Lit indicate the Switch is successfully connecting to the network at 1000Mbps 1000 Green Off indicate that the Switch is successfully connecting to the network at 10Mbps o
10. r 100Mbps Lit indicate the link through that port is successfully established Blink indicate that the Switch is actively sending or receiving data over that port LNK ACT Green 2 1 4 Switch Rear Panel Figure 2 2 shows a rear panel of GSD 805 100 240V AC TEE 50 60Hz 8 Figure 2 2 GSD 805 rear panel 4 12 1 The device is a power required device it means it will not work till it is powered If your networks should active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent g you from network data loss or network down Power time Notice 2 In some area installing a surge suppression device may also help to protect your Switch from being damaged by unregulated surge or current to the Switch or the power adapter 2 2 Installing the Switch This part describes how to install your Gigabit Ethernet Switch and make connections to it Please read the following topics and perform the procedures in the order being presented This Gigabit Ethernet Switch does not need soft ware configuration 2 2 1 Desktop Installation To install the Gigabit Ethernet Switch on desktop simply follow the next steps Step 1 Attach the rubber feet to the recessed areas on the bottom of the Gigabit Ethernet Switch Step 2 Place the Gigabit Ethernet Switch on desktop near an AC power source Step
11. t Automatic address learning and address aging Supports Auto MDI MDI X function Support CSMA CD protocol Internal power adapter 100 240V AC 50 60Hz 0 2A FCC CE class A compliant 741 1 4 Product Specifications Product GSD 805 Hardware Specification 10 100 1000Base T 8 Ports Dimensions W x D x H 191 mm x 85 mm x 26 mm Weight 390g Power Requirement Internal power 100 240V AC 50 60Hz 0 2A Power Consumption Dissipation 9 6 watts 32 BTU Switch Specification Switch Processing Scheme Store and Forward Address Table 4K entries Share data Buffer 1Mbit on chip frame buffer Back pressure for half duplex IEEE packet per second Fow Gonirel 802 3x Pause Frame for full duplex Switch fabric 16Gbps Throughput 11 9Mpps Network cables 10 100 1000Base T Cat 3 4 5 5e 6 UTP cable 100meters max EIA TIA 568 100 ohm STP 100meters max 48 Standards Conformance IEEE 802 3 Ethernet Standards IEEE 802 3u Fast Ethernet Compliance IEEE 802 3ab Gigabit Ethernet IEEE 802 3x Full duplex flow control Operating 0 50 degree C Te ti IE Storage 40 70 degree C Humidity Operating 90 Non condensing Operating 5 to 90 Storage 5 to Regulation FCC Part 15 Class A CE Compliance 9 1 2 INSTALLATION This section describes the functionali
12. ties of the Gigabit Ethernet Switch s components and guides how to install it on the desktop Basic knowledge of networking is assumed Please read this chapter completely before continuing In the following section the term Gigabit Ethernet Switch means the GSD 805 2 1 Product Description The PLANET GSD 805 is 8 Port 10 100 1000Mbps Gigabit Ethernet Switch with non blocking wire speed performance and new metal shape for easily desktop deployment in compact housing or SOHO application With a 16Gbps internal switching fabric the Gigabit Ethernet Switch can handle extremely large amounts of data in a secure topology linking to a backbone or high capacity servers The Gigabit Ethernet Switch has 4K MAC Address table and offers wire speed packets transfer performance without risk of packet loss The Gigabit ports with 9K jumbo packet support can handle large amounts of data transmission in a secure topology linking to a backbone or high power servers The high data throughput of the device makes it ideal for most Gigabit environments especially network upgrades to a Gigabit environment All RJ 45 copper interfaces support 10 100 1000Mbps Auto Negotiation for optimal speed detection through RJ 45 Category 6 5 or 5e cables Support standard for Auto MDI MDI X that can detect the type of connection to any Ethernet device without requiring special straight or crossover cables The Flow Control function allows Gigabit Ethernet Sw
13. y port The Gigabit Ethernet Switch will record the source address port no And the other related information in address table This information will be used to decide either forwarding or filtering for future packets 3 3 Forwarding amp Filtering When one packet comes from some port of the Gigabit Ethernet Switch it will also check the destination address besides the source address learning The Gigabit Ethernet Switch will lookup the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will transmit this packet to the network it connected If found and the destination address is located at different port from this packet comes in the Gigabit Ethernet Switch will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet comes in then this packet will be filtered Thereby increasing the network throughput and availability 15 1 3 4 Store and Forward Store and Forward is one type of packet forwarding techniques A Store and Forward Gigabit Ethernet Switch stores the incoming frame in an internal buffer do the complete error checking before transmission Therefore no error packets occurrence it is the best choice when a network needs efficiency and stability The
Download Pdf Manuals
Related Search