Air-Mate™ Belt-Mounted High Efficiency Powered Air
Contents
1. ASSEMBLY Breathing Tube To connect the breathing tube to the PAPR unit insert the breathing tube male end with pin into the PAPR unit and twist clockwise to lock in place To connect the breathing tube to the headgear see the appropriate headgear User Instructions Battery Installation 1 Remove the back cover and the filter from the PAPR unit 2 Insert the battery pack into its compartment and press it down to seat in place This action will engage the battery terminals in the socket on the side of the battery pack Fig 2 Slide the battery pack clip under the slot on the housing to hold in place Assure that the filter gasket is properly installed in the grove on the housing Replace the filter with arrows pointing in towards the battery ON Pn ey 9 Snap the back cover into place Battery Filter Clip Gasket Battery Terminals CSS man Fig 2 Battery Charging A completely exhausted battery pack should be charged for 16 to 24 hours To use the 3M smart battery charger place the charging station horizontally on a flat surface and plug the station AC power cord into a regulated 120v 60Hz outlet The green LED light will turn on Insert the charging lead into the socket in the side of the blower filtration unit Alternatively the battery can be removed from the blower filtration unit and charged using the external charging adapter sold separately as part number 520 04 24 The LED will turn off in2. In United States contact Internet www 3M com occsafety Technical Assistance 1 800 243 4630 For other 3M products 1 800 3M HELPS or 1 651 737 6501 3M Occupational Health and Environmental Safety Division 3M 2005 Printed in USA 3M Center Building 0235 02 W 70 St Paul MN 55144 1000 38 9019 0907 7 98 0060 0030 5 1 17 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com
3. leaving the contaminated area Doing so may result in sickness or death Contaminants that are dangerous to your health include those that you may not be able to see or smell Leave the contaminated area immediately if any of the following conditions occur Failure to do so may result in sickness or death Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com Airflow decreases or stops Any part of the system becomes damaged Airflow into the respirator decreases or stops Breathing becomes difficult You feel dizzy or your vision is impaired You taste or smell contaminants Your face eyes nose or mouth become s irritated You suspect that the concentration of contaminants may have reached levels at which this respirator may no longer provide adequate protection Do not expose blower filter assembly directly to sparks or molten metal spatter Direct contact with sparks or molten metal spatter may damage the filter allowing unfiltered air into the breathing zone which may result in sickness or death and may cause the filter or blower housing to ignite resulting in serious injury sickness or death Do not clean respirator with solvents Cleaning with solvents may degrade some respirator components and reduce respirator effectiveness Inspect all respirator components before each use to ensure proper operating conditions Failure to do so may resu
4. unit and battery are not waterproof They should not be submersed or subjected to heavy spraying with water or other liquids High concentrations of mist or sprays may temporarily clog filters and cause airflow to drop below safe levels 2 Remove the respirator system in a clean area Refer to the Inspection Cleaning and Storage sections of these User Instructions for cleaning inspection and storage information 14 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com CLEANING AND STORAGE Follow the hygiene practices established by your employer for the specific contaminants to which you have been exposed Do not clean respirator with solvents Cleaning with solvents may degrade some respirator components and reduce respirator effectiveness Inspect all respirator components before each use to ensure proper operating conditions Failure to do so may result in sickness or death Cleaning Solvents should not be used to clean the PAPR blower unit battery pack or smart battery chargers Liquid solvents may chemically weaken the plastic Use the following suggested procedures for cleaning 1 Wipe the PAPR blower unit battery pack and smart battery charger with a mild cleaning solution 2 Do not immerse the PAPR blower unit battery pack or smart battery charger 3 Properly dispose of used filters Do not attempt to clean the filters Dispose of the filter according t
5. www envirosafetyproducts com 3M Accessories Product Number CB 1000 GVP 117 520 03 73 520 03 72 520 01 61 520 01 61SGL 520 01 61 FIV Description Comfort Belt fits waist sizes from 26 52 in 66 to 132 centimeters Waist Belt Vinyl Smart Battery Charger Single Unit Smart Battery Charger 5 Unit Smart Battery Charger 10 Unit Smart Battery Charger Single Unit Canada only Smart Battry Charger 5 Unit Canada only NIOSH Approved System Configurations The Air Mate PAPR unit must be combined with a headpiece respiratory inlet cover and breathing tube in accordance with the following table to form a complete NIOSH approved respirator system 3M TM Headpiece 3M Breathing Tube Current Formerly Current Formerly BE 10 Series Hoods R Series Hoods BE 10 3 522 01 11R03 BE 224 008 00 14R01 Polyurethane 38 inch Polyurethane 38 inch BE 10 20 522 01 11R20 BE 10L 20 522 02 17R03 Current BE 12 Series Head Covers R Series Head Covers Formerly BE 12 3 522 02 00R03 BE 12 50 522 02 00R50 BE 12B 3 522 02 01R03 BE 12B 50 522 02 01R50 BE 12L 3 522 02 02R03 BE 12L 50 522 02 02R50 BE 12LB 3 522 02 03R03 BE 12LB 50 522 02 03R50 Note 3M Hoods R Series to BE Series denotes a product number change only no change to product Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com
6. 30 days Without periodic charging a NiCd battery in storage loses approximately 1 of its charge each day Infrequently used battery packs should be fully charged initially then charged overnight once per week or one hour each day to maintain a full charge Allowing a battery to self discharge during extended storage will not harm the battery pack Batteries subjected to prolonged storage longer than 6 months may loose their capacity to hold a full charge Battery capacity can be checked by running the PAPR motor blower unit for eight hours and checking that airflow is maintained at six CFM or greater Several charge run down cycles may restore battery capacity Do not charge multiple battery packs in an enclosed cabinet without ventilation To properly dispose of the battery pack follow local solid waste disposal regulations or call the RBRC Battery Recycling Information Helpline at 1 800 8 BATTERY 1 800 822 8837 Filter and Filter Gasket The high efficiency filter must be changed When an airflow check of the PAPR unit reveals that the airflow indicator does not rise to the specified level with a properly charged battery pack powering the PAPR unit When the filter has been physically damaged When water has entered the high efficiency filter or In order to comply with local administrative procedures Examine the new high efficiency filter and if no damage is evident change the filter as follows Removal Pull t
7. 3M Air Mate Belt Mounted High Efficiency Powered Air Purifying Respirator User Instructions for Air Mate PAPR Assembly 231 01 30 and Air Mate PAPR Unit 520 03 63RO01 Keep these User Instructions for reference This product helps protect against certain airborne particles Misuse may result in sickness or death For proper use see supervisor User Instructions or call 3M in U S A 1 800 243 4630 In Canada call Technical Service at 1 800 267 4414 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com TABLE OF CONTENTS GENERAL SAFETY INFORMATION j3 ccsscssscstsccnseacsoscxccsvcscsovenonavoud coceencsevnnsevasandeenasesedennsanegeaieds 3 l tended Usera nn heee ales ed a adhe aut eda R A E A N S SE cachet 3 List of Warnings and Cautions within these User Instructions sseeeseeseesesreeeesreersssrerresrrerssse 3 USE INSTRUCTIONS AND LIMITATIONS ssessesssseessesesssesserssseesseresseessseessesseressresseressereseeessee 4 TIVO A ABE E A E E E E E E E E 4 Use Forme Aya ea dio Sree a E A a a ee ee eek 4 Do N t bse FOr ee e as Sai ee ee i a aed 4 Respirator Selection and Tra nini oo oe Gs ate cas Sess stacs se scas tacesedac dessus a a a n aa A 4 Assigned Pr tection FAClONJs cswaauccnsiasaavyagsyadeoncdontvoatanainbaatcabeauneea hianed ivmet ad E A 6 NIOSH Approval spiria eiaensdis avai va tsacats E stun ae annie eae es 6 NIOSH Cautions and EaniitatOn
8. ate matter inside the blower may indicate a damaged filter or improper seating of the filter cartridge to the gasket Contact 3M Technical Service for assistance ee FS Examine the outside of the battery for cracks Replace if damaged Inspect the breathing tube and replace if punctured cracked or worn Bend the breathing tube to verify that it is flexible Ser Successfully complete the applicable User Performance Check USER PERFORMANCE CHECK Failure to pass a user performance check and complete all necessary repairs before use may adversely affect respirator performance and result in sickness or death 1 Ensure that the breathing tube is connected to the PAPR unit Hold the free end of the tube up by grasping the slotted connector and covering the slots of the connector with thumb and forefinger Drop the black bullet shaped airflow indicator pointed end first into the slotted connector Fig 3 2 Switch the PAPR unit on Hold the tube so that it is vertical and at eye level The indicator should float on the air coming out and the lower band on the indicator should be above the connector s rim 3 Ifthe lower band on the indicator rises above the slotted connector edge airflow is sufficient If the indicator fails to rise to this level airflow is insufficient This may be the result of a battery with a low charge a clogged filter or another malfunction Refer to Troubleshooting section 12 Enviro Safety P
9. ckel cadmium Up to 8 hrs of use per charge Airflow range Greater than 6 cfm 170 lpm Weight PAPR Approximately 1 1 1b 0 5 kg Weight battery pack Approximately 1 7 1b 0 8 kg 6 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com SYSTEM COMPONENTS AND REPLACEMENT PARTS Do not use with parts or accessories other than those manufactured by 3M as described in these User Instructions or on the NIOSH approval label for this respirator Do not attempt to repair or modify any component of the system except as described in these User Instructions Failure to do so may adversely affect respirator performance and result in sickness or death 3M Components and Replacement Parts Product Number Description 231 01 30 Air Mate PAPR Assembly includes PAPR unit battery filter belt and airflow indicator 520 03 63RO01 Air Mate PAPR Unit does not include battery pack belt and airflow indicator Fig 1 007 00 15R01 Battery Pack 451 02 01R01 High Efficiency Filter includes gasket GVP 127 Waist Belt Web 021 41 02R01 Waist Belt Nylon 59 long 150 cm 021 14 00RO1 Airflow Indicator 021 10 07RO1 Back Cover for PAPR unit Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com Fig 1 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at
10. dicating that the battery pack attached is being charged in a high rate mode After approximately eight hours depending on the amount of charging required the LED will turn back on indicating that the charger has switched to a trickle rate mode preventing damage to the 10 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com battery from overcharge For Canada chargers when in trickle mode the LED light will cycle on and off every 3 5 seconds 3M batteries provide up to 500 charge discharge cycles However the life of 3M batteries will be significantly reduced when they are exposed to high heat over an extended period of time To maximize battery life these guidelines should be followed Charge 3M battery packs before they are completely discharged Damage may occur if the battery pack is completely discharged deep discharged frequently 3M battery packs may be charged any time during the discharge cycle Unlike some NiCd batteries 3M battery packs do not develop a memory Whether it has been used 30 minutes or 8 hours the battery pack may be charged Always charge batteries at a temperature of 77 F 25 C or less At higher temperatures the battery pack may not accept a full charge If a battery pack feels hot let it cool for 1 2 hour before charging Batteries may be left on trickle rate mode to maintain optimum capacity for up to
11. erformance and result in sickness or death Do not use with parts or accessories other than those manufactured by 3M as described in these User Instructions or on the NIOSH approval label for this respirator Do not attempt to repair or modify any component of the system except as described in these User Instructions Failure to do so may adversely affect respirator performance and result in sickness or death Failure to conduct an inspection and complete all necessary repairs before use may adversely affect respirator performance and result in sickness or death Failure to pass a user performance check and complete all necessary repairs before use may adversely affect respirator performance and result in sickness or death Use of this respirator in atmospheres for which it was not NIOSH certified or designed may result in sickness or death Do not wear this respirator where Atmospheres contain hazardous vapors or gases Atmospheres are oxygen deficient Contaminant concentrations are unknown Contaminant concentrations are Immediately Dangerous to Life or Heath IDLH Contaminant concentrations exceed the assigned protection factor APF recommended for the applicable headpiece or the APF mandated by specific government standards whichever is lower Refer to the User instructions provided with the applicable headpiece Do not enter a contaminated area until properly donning the respirator system Do not remove the respirator before
12. erly plugged into charger attached and locked into the PAPR housing PAPR fails airflow test Clogged filter Replace filter Battery needs charging Charge battery Battery does not hold charge Replace battery Breathing tube blocked Locate and remove restriction 16 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com IMPORTANT NOTICE WARRANTY In the event any 3M OH amp ESD product is found to be defective in material workmanship or not in conformation with any express warranty for a specific purpose 3M s only obligation and your exclusive remedy shall be at 3M s option to repair replace or refund the purchase price of such parts or products upon timely notification thereof and substantiation that the product has been stored maintained and used in accordance with 3M s written instructions EXCLUSIONS TO WARRANTY THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR OTHER WARRANTY OF QUALITY EXCEPT OF TITLE AND AGAINST PATENT INFRINGEMENT LIMITATION OF LIABILITY Except as provided above 3M shall not be liable or responsible for any loss or damage whether direct indirect incidental special or consequential arising out of sale use or misuse of 3M OH amp ESD products or the user s inability to use such products THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE FOR MORE INFORMATION
13. he belt through the belt retainers to form a loop which is clear of the PAPR unit Release the back cover s locking tabs and remove the back cover Remove and discard the high efficiency filter and filter gasket in accordance with local state and federal guidelines Replacement Inspect the new filter gasket and ensure that it is not torn or damaged before proceeding Fit the new filter gasket into the filter support ridge ensuring that the gasket is flush against the sides of the PAPR unit leaving no gaps Fit the replacement filter into the PAPR unit with the arrows pointing into the PAPR unit Snap the back cover s locking tabs into the rear of the PAPR unit Pull the belt through the belt retainers 11 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com INSPECTION Failure to conduct an inspection and complete all necessary repairs before use may adversely affect respirator performance and result in sickness or death An inspection must always be performed prior to each use of the respirator as follows Remove the back cover and filter Check that the filter gasket is clean in good condition and properly installed Examine the blower housing for cracks or warping Check that the battery latch is fully extended under the retaining ledge in the blower housing Examine the inside of the blower housing and fan assembly The presence of dust or other particul
14. lt in sickness or death Never attempt to clean filters by knocking or blowing out accumulated material This may result in damage to the filter membrane allowing hazardous particles to enter the breathing zone resulting in sickness or death USE INSTRUCTIONS AND LIMITATIONS Important Before use the wearer must read and understand these User Instructions Keep these User Instructions for reference Use For Respiratory protection against certain airborne particulate contaminants including dusts fumes mists radionuclides and asbestos Do Not Use For Protection from gases or vapors Oxygen deficient atmospheres Contaminant concentrations that are unknown or immediately dangerous to life or health IDLH Contaminated concentrations that exceed the assigned protection factor APF recommended for the applicable headpiece or the APF mandated by specific government standards whichever is lower Refer to additional limitations and cautions under NIOSH Cautions and Limitations Respirator Selection and Training Use of these respirators must be in accordance with applicable health and safety standards respirator selection tables contained in such publications as American National Standards Institute ANSI Z88 2 1992 Canadian Standards Association CSA Standard Z94 4 or pursuant to the recommendations of an industrial hygienist The employer must have a written respirator program in place which is in accordance with the Occu
15. nderstand these User Instructions Keep these User Instructions for reference Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com GENERAL SAFETY INFORMATION Intended Use The belt mounted Air Mate PAPR Assembly consists of a blower unit a high efficiency filter and a rechargeable nickel cadmium battery pack The blower unit draws contaminated air through the high efficiency filter before it enters the breathing tube in the rear of the headgear The PAPR unit includes an on off switch for safety and convenience When combined with appropriate 3M breathing tubes and headpieces the Air Mate PAPR Assembly 231 01 30 forms a complete NIOSH approved powered air purifying respirator PAPR These PAPR systems are intended to help provide respiratory protection against certain airborne particulate contaminants List of Warnings and Cautions within these User Instructions This product helps protect against certain airborne particles Misuse may result in sickness or death For proper use see supervisor User Instructions or call 3M in U S A 1 800 243 4630 In Canada call Technical Service at 1 800 267 4414 Each person using this respirator must read and understand the information in these User Instructions before use Use of these respirators by untrained or unqualified persons or use that is not in accordance with these User Instructions may adversely affect respirator p
16. o applicable regulations 4 Disconnect breathing tube from the headpiece and PAPR unit Flush breathing tube with mild cleaning solution and soak as necessary Flush with clean water and let drain until drippings stops Immediately connect breathing tube to an assembled PAPR unit and run system for a minimum of 1 2 hour with the breathing tube hanging downward Never attempt to clean filters by knocking or blowing out accumulated material This may result in damage to the filter membrane allowing hazardous particles to enter the breathing zone resulting in sickness or death Storage Store your respirator at room temperature in a dry area that is protected from exposure to hazardous contaminants 15 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com TROUBLESHOOTING Possible Cause Corrective Action You smell or taste contaminants Misuse improper assembly or Leave work area immediately or an irritation occurs malfunction of equipment and contact your supervisor Do not use the PAPR until the cause is identified and corrected Blower does not run when switch Battery is discharged Recharge 14 16 hours is depressed Faulty power switch Replace battery pack Faulty motor Replace motor blower Battery does not accept charge Faulty battery connection or Check that battery terminals are but PAPR unit runs when terminals dirty damaged clean and battery is prop
17. ontact 3M Technical Service at 1 800 243 4630 NIOSH Cautions and Limitations A Not for use in atmospheres containing less than 19 5 percent oxygen B Not for use in atmospheres immediately dangerous to life or health C Do not exceed maximum use concentrations established by regulatory standards F Do not use powered air purifying respirators if airflow is less than four cfm 115 Ipm for tight fitting facepieces or six cfm 170 lpm for hoods and or helmets I Contains electrical parts which have not been evaluated as an ignition source in flammable or explosive atmospheres by MSHA NIOSH J Failure to properly use and maintain this product could result in injury or death L Follow the manufacturer s User s Instructions for changing cartridges canister and or filters M All approved respirators shall be selected fitted used and maintained in accordance with MSHA OSHA and other applicable regulations N Never substitute modify add or omit parts Use only exact replacement parts in the configuration as specified by the manufacturer O Refer to User s Instructions and or maintenance manuals for information on use and maintenance of these respirators P NIOSH does not evaluate respirators for use as surgical masks SPECIFICATIONS Heat and flame resistance This respirator system is not designed for use in high temperature environments and should not be exposed to sparks or flame Battery pack Rechargeable ni
18. pational Safety and Health Administration OSHA respiratory protection standard found in 29 CFR 1910 134 prior to using any respirator In Canada follow CSA standard Z94 4 or the requirements of the authority having jurisdiction in your region Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com Before use the employer must assure that each respirator user has been trained by a qualified person in the proper use and maintenance of the respirator and air supply components according to the instructions contained in these User Instructions and other applicable User Instructions Each person using this respirator must read and understand the information in these User Instructions before use Use of these respirators by untrained or unqualified persons or use that is not in accordance with these User Instructions may adversely affect respirator performance and result in sickness or death Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com Assigned Protection Factor Refer to the User Instructions supplied with the respirator headpiece for information on protection factors NIOSH Approval For a listing of the components of NIOSH approved 3M Respirator Systems using 3M Air Mate PAPR Unit 520 03 63RO01 refer to the NIOSH approval label that is part of the User Instructions included with the product or c
19. roducts 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com opar Airflow Indicator Lower Band Slotted Connector Breathing Tube Airflow Indicator Airflow Fig 2 Fig 3 DONNING THE PAPR 1 Complete assembly inspection and user performance check of the PAPR assembly as described in these User Instructions 2 Complete assembly and fitting of the respirator headpiece in accordance with the User Instructions provided with the respirator headpiece 3 Place the belt with PAPR assembly around the waist and snap the buckle closed Adjust the belt as needed for a comfortable and secure fit 4 Press the power switch to turn the system on and verify that air is flowing to the headpiece 5 Don the respirator headpiece then enter the contaminated area 13 Enviro Safety Products 8248 West Doe Ave Visalia CA 93291 1 800 637 6606 Visit us at www envirosafetyproducts com OPERATING INSTRUCTIONS Use of this respirator in atmospheres for which it was not NIOSH certified or designed may result in sickness or death Do not wear this respirator where Atmospheres contain hazardous vapors or gases Atmospheres are oxygen deficient Contaminant concentrations are unknown Contaminant concentrations are Immediately Dangerous to Life or Heath IDLH Contaminant concentrations exceed the assigned protection factor APF recommended for the applicable headpiece or the APF manda
20. s lt t u2 s vsbucesedscundewespucbsedenvadietesustaissnuederegushucdcqund de tehwehantebindeadeouags 6 SPECIFICATIONS 3 issih ee eee er i a Re Re a ee 6 SYSTEM COMPONENTS AND REPLACEMENT PARTS Q eessccssssceeeseceeesececesececesaeeeesaeeeeeas 7 NIOSH Approved System Oni uration cu cutak ccna des eceoxasece gee suc cave ace yuu Saree caceeee cate grtusenconees 9 PS MIB Te a e ae ea Al eat title Sasa dita aa Laled tae 10 MSV ALIA Te DID stesso srs E ss ra a se cco saw Saas ea Res E A EE SE es 10 Battery Installations sisi tec Nico Site is ig Geta eg ele bas ada eine a wang cine 10 Battery Charging usisne airmen awa aie awn E nee ama 10 Filter and Filter Gaskets sscani tists acca sind ister ia AE cued S A ts eS ences N E eA ST 11 MSP OTO N E a E a a E A A ES 12 USER PERFORMANCE CHECK arei a Snel E me A E A 12 DONNING THEE APIS osiris atenei naaa aaa A aE aa a EA haste aaa a a aa A Aaoi ei 13 OPERATING INSTRUCTIONS oiee a i a a a e 14 CLEANING AND STORA GE ohe a A a e R A A E A A E A ERN 15 Ui ANI EAEE A sachet ca E N E E A E E E E 15 Stota irra a a ee eea pap aaraa cd ea eai a aa ae a eenas raae e Seha 15 HERO Pe SOOO TIN Ge tos ea tc cpu A EAA 16 IMPORTANT NOTICE eerie iaaa E aaa E Eao gad ART EERE Saa E Eao i aa TEE 17 FOR MOREINFORMATION s uiiarocnn sionn a R a aaa 17 If final printed User Instruction ends up in a booklet form include this following statement on front cover Important Before use the wearer must read and u
21. ted by specific government standards whichever is lower Refer to the User instructions provided with the applicable headpiece Do not enter a contaminated area until properly donning the respirator system Do not remove the respirator before leaving the contaminated area Doing so may result in sickness or death Contaminants that are dangerous to your health include those that you may not be able to see or smell Leave the contaminated area immediately if any of the following conditions occur Failure to do so may result in sickness or death Airflow decreases or stops Any part of the system becomes damaged Airflow into the respirator decreases or stops Breathing becomes difficult You feel dizzy or your vision is impaired You taste or smell contaminants Your face eyes nose or mouth become s irritated You suspect that the concentration of contaminants may have reached levels at which this respirator may no longer provide adequate protection Do not expose blower filter assembly directly to sparks or molten metal spatter Direct contact with sparks or molten metal spatter may damage the filter allowing unfiltered air into the breathing zone which may result in sickness or death and may cause the filter or blower housing to ignite resulting in serious injury sickness or death 1 After successfully completing the donning procedures enter the contaminated area breathing normally Note This PAPR
Download Pdf Manuals
Related Search