The points described below are: the on/off button , the current switch
Contents
1. The pump has three connectors right center and left The right is the discharge connector and must therefore be connected to the connector on the left of Final discharge unit The middle connector must be connected to the valve controlled loss valve and should be connected to The final discharge unit right connector W The left connector of the pump must be connected to the cylinder The scheme described above should be followed as pictured The discharge connector is important do not invert it If it is inverted the pump will not generate any vacuum but there are not obviously dangers or damage to the device Final discharge unit The final discharge unit must be completely immersed about 6 cm in water during operation of the pump It must be connected the discharge tube and the tube connected to the controlled loss valve Controlled loss valve The valve is positioned on the final discharge unit during use of the pump must be completely immersed in water The white knob on the head of the valve controls the rate of descent of the vacuum You have to adjust it by gently tightening or loosening 1 or 2 mm at a time so finding the right setting at your leisure Valve adjustments should be made keeping it totally immersed in water If you fully tighten clockwise there would be no leak and the vacuum level would remain stable Regulation intensity knob The intensity control knob above is a current regulator2. Press center S button one time and ensure the setting for oUI is HYS if not press up or down arrows to change the value 8 Press center S button one time and ensure the setting for lot is I_n if not press up or down arrows to change the value 9 Press center S button one time and ensure the setting for n_I is 3 your minimum vacuum if not press up or down arrows to change the value 10 Press center S button one time and ensure the setting for H 1 is 7 your maximum vacuum if not press up or down arrows to change the value 11 Press center S button one time and ensure the setting for Col is Sor if not press up or down arrows to change the value 12 Press center S button one time and arrive at F 1 and settings is complete 13 Press and hold center S button for 3 4 seconds to arrive at vacuum display Ensure the display is red and the value is 0 0 0 1 and screw black knob clockwise to desired pumping speed
3. USER MANUAL ELECTRIC DYNAMIC PUMP This manual briefly explains the operation of the device The points described below are the on off button the current switch power and charging connectors water connectors final discharge controlled loss valve regulation intensity knob display battery charge indicator cylinder supplied and operation of filling and emptying depiction connection tubes how best to use the device and setting vacuum values The on off button The on off button turn the device on and off In I position the device is in operation in O position the device is off The switch As in the figure above the switch selects the type of power supply only for the dual power supplymodel A C batteries with AC batteries or power supply The switch positioned on the left black color uses battery supply device The switch positioned on the right operates the device with AC mains power via a transformer To use the battery keep the selector positioned on the left To use AC power keep the switch positioned to the right In order to recharge the battery keep the switch positioned to the left If while using the battery powered device the switch is moved to the right the device will lose power and stop The left connector is only used to recharge the battery while the device is not in use The right connector is for AC power supply and should only be used to supply the device while it is in use Water connectors
4. ed and operation of filling and emptying Our pump could work with all kinds of cylinder but we have designed one tailored to the needs of our device to be able to offer you the best possible comfort in the use of our dynamic water pump The cylinder has two connectors and internal wing in line with one of the two connectors this connector must be connected to the pump tube see figure above you have to wear the cylinder with wing pointing on as the figure above we will call this connector connector 1 up The inner wing perform a very important function serves to hold any air bubbles due to possible losses caused by poor adherence between the cylinder and the base of the penis If during the use of the pump you realize you have air bubbles in the cylinder just move the cylinder towards the vertical position so that the bubbles rise up to the highest point of the cylinder ie the circular top where the two connectors are positioned at this point place the cylinder in the desired position and the air bubbles remain trapped in the wing specially designed containment The second connector of the cylinder is used exclusively to fill and empty the cylinder and we call it connector 2 down By using water you d think that you would get wet or that you will surely have water leaks in the place where you use the device However it is not so By holding the cylinder in a nearly horizontal position with the tip slightly upturned simply connect
5. isconnect the hose provided WE STRONGLY RECOMMEND USING WARM WATER IN THIS PUMP It is generally considered warmth assists in achieving the BENEFITS this device is capable of AND PREVENTION of injuries that can result from excessive pumping eg red spots Setting vacuum values The device is equipped with three buttons from which you can regulate the minimum and maximum vacuum which can be set in two different ways Setting minimum vacuum N_I 1 To set minimum vacuum turn on the device by turning the power switch on I position The display will show 0 1 0 2 2 now press the central button JW You will display the flashing writing N I present value 3 Press the button on the right E7 to decrease or press the button on the left AJ to increase 4 press the central button once more and you have finished setting minimum vacuum For example use the side left and right buttons to set 3 7 Hg So the value 3 7 Hg that you have just set means that when vacuum arrives to 3 7 the device starts and leads the vacuum to the maximum preset value the vacuum inside the vacuum circuit will not decrease under 3 7 To set the maximum vacuum value vacuum that the device will reach you set a number H 1 H Irepresents the increase in vacuum from the minimum set vacuum N 1 ie Maximum set vacuum N 1 H D Setting H I 1 Turn on the device by pressing I the display will show 0 1 0 2 hold down the central button a for a
6. t least 3 seconds the display will show the writing F 0 2 press the left button Ad once the display will show the writing F 1 3 Now press the central button four times until the display shows the writing H_I You increase with the button on the left and decrease with that on the right 4 then press again the central button for at least 3 seconds the display will show the writing 0 1 0 2 and you have now set the maximum value Examples If you want to make cycles at a minimum vacuum of 4 0 and a maximum vacuum of 9 0 set the minimum value N_I at 4 0 and set H_I value at 5 0 Cycles at a minimum vacuum of 3 3 and maximum vacuum of 10 2 set N I to 3 3 set H Ito 6 9 cycles at a minimum vacuum of 4 5 maximum vacuum of 8 7 set N_I 4 5 and H_I to 4 2 cycles at a minimum vacuum 5 5 maximum vacuum 11 0 set N I to 5 5 and H Ito 5 5 Note If you have 4 0 as minimum value and 8 0 as maximum value when you modify only the value N I that is 4 0 and you bring it to 5 0 for example you will obviously increase the maximum value H 1 too so it will automatically become 9 0 so you will have 5 0 as minimum value and 9 0 as maximum value It might seem complicated but in reality it is simple because if correctly used usually you will normally only change the maximum value while you will almost always have the same minimum value ie you will normally only modify the H I value You are advised to adj
7. that regulates the speed and the noise level of the device It must be used gently The intensity increases by turning it clockwise The intensity decreases by turning it anti clockwise If you turn the knob completely anti clockwise you remove power to the device and it stops This is normal The knob regulates the speed of vacuum increase and also the noise though moderate that the device emits Applying more power to the vacuum pump draws out air more quickly from the vacuum circuit clockwise Applying less power to the vacuum pump draws out air more slowly anti clockwise The display From the display you can display the vacuum value inside the circuit When the vacuum pump is active the numbers will be displayed in red When the pump is not active the numbers will displayed in green When the device starts the display flashes for some seconds about 2 seconds and it starts at the values that have been set previously The display shows the vacuum inside the vacuum circuit in inches of Hg they can also be displayed in Bar Psi etc Without having closed the vacuum circuit by connecting the small tube the display will show 0 1 0 2 that is normal since there is no vacuum Led indicator battery charge level When it is green the charge 1s about 100 when is Yellow indicates a charge from 80 to 30 When is red indicates a charge under 30 and then you have to recharge before the next use of the device Cylinder suppli
8. the supplied hose connector 2 down put it in the water and turn on the device in less than a minute the tube will be filled with water then place the cylinder vertically so that all air is sucked into the connector 1 when the cylinder is full of water and will have a total absence of air bubbles disconnect the hose supplied from connector 2 and you can begin the session At the end of use of the device to empty the cylinder connect the supplied hose to connector 2 and aim it at a drain water Keep the cylinder pointing down in about a minute the cylinder will be emptied of water Depiction connection tubes How best to use it In this section we will explain in a few essential points and most important how to use the device 1 Rest the device on a flat surface near the water source connect final discharge unit to the pump the right connector of the pump into the left connector of the final discharge unit the middle connector of the pump into the right connector of the final discharge unit completely immerse the final discharge unit in water 2 Wear the cylinder connect the connector 1 up into the connector left of the pump insert the hose provided in connector 2 down of the cylinder and keep it in the water turn on the pump and with the knob give maximum power to fill the cylinder 3 When the cylinder is almost full of water point it out As soon it is completely full of water and without air bubbles inside d
9. ust minimum and maximum values by following this handbook exclusively without relying on any other menu option but if you unconfigure the menu in error with the buttons under the display contact mrfantasticpumping hotmail it we will help you with reprogramming Lithium ion battery The dual power supply version of the device includes a lithium ion battery a very powerful and safe new generation battery that can supply the device for some hours with a range of at least two full hours the battery charging must be done exclusively when the device is not in use The battery must be charged when necessary do not charge the battery continually if it is not out of power for about 70 80 or there will be the risk of nullifying its duration Static pumping The device has been designed for dynamic pumping It has a natural slow vacuum leak that is amplified and regulated by the controlled loss valve If you wish to use the device for static pumping you have to remember that is does not maintain a constant vacuum but will always tend to slowly lose vacuum Checking pump settings 1 Turn on the device 2 Turn the black knob fully counterclockwise 3 Press the central S button for 3 4 seconds and arrive in F O 4 Press center S button one time and ensure the settings for uni is inH if not press up or down arrows to change the value 5 Press center S button one time arriveat F O 6 Press left up button one time and arriveat F 1 7
Download Pdf Manuals
Related Search