1 - Triumph Adler
Contents
1. To keep the copier cool and facilitate changing of parts and maintenance allow access space as shown below Other precautions Leave adequate space especially around the left Connect the power plug to the closest outlet possible cover to allow air to be properly ventilated out of the Q to the copier MN The power supply cord is used as the main disconnect device Ensure that the socket outlet is Rear located installed near the equipment and is easily gt 1113 16 30 cm accessible Left z 1911 16 50 eins E Handling of plastic bags 30 cm A WARNING n Keep the plastic bags that are used with the copier away from children The plastic may cling to their nose and mouth causing suffocation Front gt 393 s 100 cm Other precautions Adverse environmental conditions may affect the safe operation and performance of the copier Install in an air conditioned room recommended room temperature around 68 F 20 C humidity around 65 RH and avoid the following locations when selecting a site for the copier Avoid locations near a window or with exposure to direct sunlight Avoid locations with vibrations Avoid locations with drastic temperature fluctuations Avoid locations with direct exposure to hot or cold air Avoid poorly ventilated locations 1 2 A PRECAUTIONS FOR USE E Cautions when using the copier A WARNI2. If the paper reaches the right hand wall of the drawer the length guide is not used Store it in the space shown in the illustration IMPORTANT Load paper so that it is kept under the claw of the drawer When loading paper into the drawer make sure that the copy side is facing upward the copy side is the side facing upward when the package is opened Check that the length and width guides securely contact the paper If there is a gap adjust the position of the length or width guide to close it Load paper all at once and do not add paper until all sheets are used up If you add paper to a drawer that still contains paper a paper misfeed may occur Do not use paper with curls creases folds or with rough or uneven edges caused by improper cutting Depending on the type cut condition or storage condition of the paper copied paper may become extremely curled or a paper misfeed may occur Should such problems occur remove the paper from the drawer and turn the paper upside down CHAPTER 3 PREPARATIONS BEFORE USE Gently push the drawer back in If you force the drawer in the paper may come out from under the claw NOTE Leaving paper out of its package under high temperature and high humidity conditions may lead to problems caused by ambient moisture After loading paper into the drawer store the remaining paper sealed in the paper storage bag Also before leaving the copier in disuse for a p
3. Triumph Adler DC 2115 INSTRUCTION HANDBOOK gt As an ENERGY STAR Partner UTAX GmbH a company of TA Triumph Adler AG has determined that this product meets the ENERGY STAR guidelines for energy efficiency The ENERGY STAR program is an energy reduction plan introduced by the United States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment ENERGY STAR is a U S registered mark All rights reserved No part of this material may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying recording or by any information storage and retrieval system without permission in writing from the Publisher Legal Restriction On Copying t may be prohibited to copy copyrighted material without permission of the copyright owner It is prohibited under any circumstances to copy domestic or foreign currencies Copying other items may be prohibited Please read the instruction handbook before using the copier Keep it close to the copier for easy reference The sections of this handbook and parts of the copier marked with symbols are safety warnings meant to protect the user other individuals and surrounding objects and ensure correct and safe usage of the copier The symbols and their meanings are indicated below A DANGER Indicates that serious
4. A CAUTION Avoid inhalation ingestion skin or eye contact If ingestion occurs dilute stomach contents thoroughly with water and seek medical treatment If skin contact occurs wash with soap and water If contact with eyes occurs flush thoroughly with water and seek medical treatment Prolonged inhalation of excessive dusts may cause lung damage Use of this product as intended does not result in inhalation of excessive dusts Do not incinerate toner and toner containers Dangerous sparks may cause burn Other precautions Always read the safety instructions which are included in the box or printed on the container when handling consumables Dispose of the toner or toner containers in accordance with Federal State and Local rules and regulations Store consumables in a cool dark location If the copier will not be used for an extended period of time remove the paper from the cassette return it to its original package and reseal it A Keep away from children 1 3 NAMES OF PARTS CHAPTER 2 1 Main body Original cover Open close to set the original on the platen 2 Operation panel Contains the keys and indicators for operating the copier 3 Left cover handle Hold to open the left cover 4 Left cover Open when a paper misfeed
5. injury or even death will very possibly result from insufficient attention to or incorrect compliance with the related points A WARNING Indicates that serious injury or even death may result from insufficient attention to or incorrect compliance with the related points A CAUTION Indicates that personal injury or mechanical damage may result from insufficient attention to or incorrect compliance with the related points Symbols The symbol indicates that the related section includes safety warnings Specific points of attention are indicated inside the symbol General warning AN Warning of danger of electrical shock N tibt Warning of high temperature The symbol indicates that the related section includes information on prohibited actions Specifics of the prohibited action are indicated inside the symbol Warning of prohibited action Q Disassembly prohibited The 6 symbol indicates that the related section includes information on actions which must be performed Specifics of the required action are indicated inside the symbol Q TET Alert of required action e Heian Remove the power plug from the outlet e Always connect the copier to an outlet with a ground connection Please contact your service representative to order a replacement if the safety warnings in the handbook are illegible or if the handbook itself is missing fee required CONTENTS CHAPTER
6. left cover does not close 9 Close the left cover and multi bypass 1 0 Pull the drawer out and check that no paper is misfed 1 1 Close the drawer slowly CHAPTER 6 WHEN A PROBLEM OCCURS 6 6 CHAPTER 6 WHEN A PROBLEM OCCURS 3 Troubleshooting If trouble occurs carry out the applicable checks and actions given below If the trouble persists print out a user status report and contact your service representative Trouble Checks Action Nothing lights on the Is the power plug connected to an AC Connect the plug to an AC outlet operation panel when the outlet main switch is turned ON No copies come out when Is there any indication appearing on the Perform the corrective action corresponding the Start key is pressed operation panel to the indication Copies come out blank Are the originals set correctly When setting originals on the platen place them face down Copies come out too light Is the copier in the auto exposure mode To change the overall exposure perform auto exposure adjustment Is the copier in the Photo Text amp Photo or Adjust the exposure to the correct degree Text mode using the copy exposure adjustment keys To change the overall exposure perform the exposure adjustment for each mode Is the Add Toner indicator lit Replace the toner container Is paper wet Replace the paper with new paper Trouble Checks CHAPTER 6 WHEN A PROBLEM OCCURS Actio
7. loading paper into the multi bypass place it lengthwise as shown in the illustration Do not load paper widthwise Setting the paper size for the multi bypass Set the paper size for the multi bypass according to the paper to be loaded 1 When you select the multi bypass by pressing the Paper Select key the multi bypass indicator flashes and the current paper size of the multi bypass is indicated on the copy quantity magnification display Inch specifications L Legal letter S Statement XXX Setting of non standard size paper width for multi bypass Metric specifications A4 A4 A5 A5 A6 A6 FL Folio XXX Setting of non standard size paper width for multi bypass Setting of non standard size paper width for multi bypass will not be displayed if OFF is selected in Turning multi bypass non standard size paper setting ON OFF see page 5 2 English text panel Symbol panel CHAPTER 3 PREPARATIONS BEFORE USE 2 Select the paper size by changing the display indication using the Paper Select key Inch specifications Metric specifications The display indication can also be changed using the Number of Copies Zoom key or Number of Copies Zoom key English text panel Symbol panel Number of Number of W Copies opies 0 ey rs Enter zu 3 Press the Zoom Input Enter key The multi bypass indicator will light and normal copyi
8. paper setting ON OFF Inch 4 13 to 8 50 4 13 Metric 105 to 216 mm 105 mm The maximum width of the print area is 210 mm with respect to the paper centerline Copy limit Limits the number of copies that can be made at a time 1 to 99 copies 99 copies CHAPTER 5 COPIER DEFAULT SETTING Default code Setting item Setting contents Setting code F12 Silent mode Selects the length of time from when copying ends to when entering the silent mode which stops the motors inside the copier When 0 seconds is selected the motors stop immediately after copying has been finished 0 seconds 5 seconds 10 seconds 15 seconds 30 seconds Auto shut off Turns the auto shut off function page 4 4 ON or OFF The auto shut off function automatically turns the main switch OFF if copying is not performed for a certain period of time f auto shut off interferes with your copying operations turn this function OFF It is recommended to set a longer interval for triggering the auto shut off rather than turn it OFF Auto preheat time Selects the length of time from when copying ends to when the energy saver auto preheat function page 4 4 is triggered 5 minutes 10 minutes 15 minutes 20 minutes 25 minutes 30 minutes 35 minutes 40 minutes 45 minutes gt Auto shut off time Selects the lengt
9. 1 IMPORTANT PLEASE READ FIRST 1 1 N CAUTION LABELS ennt 1 1 A INSTALLATION PRECAUTIONS 1 2 AN PRECAUTIONS FOR USE 1 3 CHAPTER 2 NAMES OF PARTS 2 1 15 Malim DO GY ccce ter reete 2 1 2 Operation panel 2 4 CHAPTER 3 PREPARATIONS BEFORE USE 3 1 1 How to load 3 1 1 Precautions for loading paper 3 1 2 Loading paper into the drawer 3 1 3 Loading paper into the multi bypass 3 2 2 How to set originals 3 5 1 Setting an original on the platen 3 5 3 Replacing the toner container and waste toner tank 3 6 CHAPTER 4 BASIC OPERATIONS 4 1 1 Basic copying procedure 4 1 2 Enlargement reduction 4 3 1772000 CODY ennon tas 4 3 2 Standard zoom copy 4 3 3 Energy saver auto preheat function 4 4 4 Auto shut off function ssssss 4 4 CHAPTER 5 COPIER DEFAULT SETTING 5 1 1 Default settings 5 1 2 How to make default settings 5 5 CHAPTER 6 WHEN A PROBLEM OCCURS 6 1 1 Error
10. Copying can be performed at the same settings copy mode number of copies and exposure if copying is started before the auto clear function clears settings CHAPTER 2 NAMES OF PARTS 2 4 CHAPTER3 PREPARATIONS BEFORE USE 1 How to load paper Paper can be loaded into the drawer and the multi bypass 1 Precautions for loading paper After unpacking the paper ruffle it several times and then load into the tray 2 Loading paper into the drawer Up to 250 sheets of standard paper 64 to 80 g m standard paper as specified by our company or colored paper can be loaded into the drawer Set the drawer paper size according to the size of paper to be loaded see drawer paper size on pages 5 2 and 5 5 It is set to 8 1 2 x 11 letter A4 at the factory Inch specifications The drawer can hold paper of 8 1 2 x 14 legal 8 1 2 x 11 and 5 1 2 x 8 1 2 vertical sizes Metric specifications The drawer can hold paper of A4 A5 vertical and folio sizes 1 Pull the drawer out toward you as far as it will go 3 1 2 Press the drawer bottom plate down and lock it there Holding the width adjustment lever move it to align the width guide with the required paper width Paper sizes are marked inside the drawer While squeezing the presses on the sides remove the length guide and then insert it into the holes of the required paper length Paper sizes are marked inside the drawer
11. IONS BEFORE USE 3 8 CHAPTER 4 1 Basic copying procedure 1 Warm up Turn the main switch ON When warm up ends the Start indicator lights If you set an original and press the Start key before warm up ends copying automatically starts at the end of warm up English text panel Symbol panel 54X8 8x11 A5 gt A4 Full Size 1 1 A4 A5 Number of Copies Size Select 2 Function selection Set copy functions as desired Auto idi English text panel Symbol panel Paper Select 3 Paper size selection Select the paper source that contains the paper to be used from the drawer and multi bypass using the Paper Select key 4 1 BASIC OPERATIONS English text panel Symbol panel e AutoExp OText amp Photo OPhoto OText 4 Copy quality selection Copy quality can be selected according to the original type Press the image mode selection key to light the respective indicators To adjust automatically Auto Exp indicator Text and photo originals Text amp Photo indicator Photo originals Photo indicator Text originals Text indicator The copy exposure can be adjusted in all image modes see Auto exposure adjustment Text and photo original exposure adjustment Text original exposure adjustment and Photo original exposure adjustment on pages 5 1 and 5 2 The image mode used in the initial mode can be selected see Image mode on page 5 1 English text pane
12. NG DO NOT place metallic objects or containers with water flower vases flower pots cups etc on or near the copier This of situation presents a danger of fire or electrical shock should they fall inside DO NOT remove any of the covers from the copier as there is a danger of electrical shock from high voltage parts inside the copier eese DO NOT damage break or attempt to repair the power cord DO NOT place heavy objects on the cord pull it bend it unnecessarily or cause any other type of damage These types of situations present a danger of fire or electrical shock dra NEVER attempt to repair or disassemble the copier or its parts as there is a danger of fire electrical shock or damage to the laser If the laser beam escapes there is a danger of it causing blindness If the copier becomes excessively hot smoke appears from the copier there is an odd smell or any other abnormal situation occurs there is a danger of fire or electrical shock Turn the main switch OFF O immediately remove the power plug from the outlet and contact your service representative If anything harmful paper clips water other fluids etc falls into the copier turn the main switch OFF O immediately Next remove the power plug from the outlet to avoid the danger of fire or electrical shock Then contact your service repre
13. PERATIONS 3 Energy saver auto preheat function This function automatically puts the copier in the sleep mode if no copying operation is performed for a certain period of time 5 to 45 minutes In sleep mode is displayed on the copy quantity magnification display and all other indicators are turned off 4 Auto shut off function To resume copying after the energy saver auto preheat function has been activated press any of the operation section keys The length of time that the copier uses to recover from the energy saver auto preheat function can be selected between within 10 seconds priority to recovery and within 30 seconds priority to power save See Auto preheat time on page 5 3 and Preheat recovery time on page 5 3 English text panel Symbol panel This function automatically turns the main switch OFF O if no copying operation is preformed for a certain period of time 15 to 120 minutes To make copies again set the main switch to the ON position If the optional printer board is installed copying will be enabled when any of the operation keys is pressed or data is received from the computer Auto shut off function The auto shut off function is a power saving feature which automatically turns OFF O the main switch when a certain time elapses without copying being performed Copiers are generally in the standby mode more than operation mode
14. and power consumption in the standby mode occupies a large part of overall consumption Having the copier turn OFF O automatically reduces unnecessary power consumption in the standby mode or at night when the copier is left on The result is a lower electricity bill To change the time until the auto shut off function starts see Auto shut off time on page 5 3 To cancel the auto shut off function see Auto shut off on page 5 3 4 4 CHAPTER 5 COPIER DEFAULT SETTING 1 Default settings The state the copier is in at the end of warm up or when the Reset key is pressed is called the initial mode and the function settings that are automatically set for the initial mode are called the default settings The default settings can be changed according to how you wish to use the copier Setting codes are provided for the default setting items that have selection items Only the number of the setting code appears on the copy quantity display See the Setting code column in the table below for the meanings of those numbers Initial settings are indicated with an asterisk Default code Setting item Setting contents Setting code F01 User status report Prints the details of the default settings Image mode Selects the image mode at power on Auto Exposure Text amp Photo Photo Text Exposure steps Changes the number of exposure steps for the manual exposure mode Auto exposure adjustment Adjusts the o
15. and status indications 6 1 2 When paper misfeeds 6 3 1 Misfeed location indications 6 3 2 Cautions sss 6 3 3 Removal procedures 6 4 3 Troubleshooting eseeeeeesss 6 7 CHAPTER 7 CLEANING AND SPECIFICATIONS 7 1 1 Cleaning the 7 1 2 SpecifiCallonis co sat cete ed vdd 7 2 MAKING FULL USE OF THE MACHINE S ADVANCED FUNCTIONS 1 Various functions for making enlarged and W Making copies using the magnification 2 Making clear reproductions of reduced copies ratios preset in the copier photographs E Enlarging reducing copies to any size Standard zoom mode page 4 3 Copy quality selection page 4 1 in the 50 200 range Zoom copy mode page 4 3 aoc de ghi j len Ighijk ijk hik ijk abcde g abcdelghi k 200 CHAPTER1 IMPORTANT PLEASE READ FIRST A CAUTION LABELS Caution labels have been attached to the copier at the following locations for safety purposes BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when removing a paper jam or when replacing toner Label 2 High temperature inside Do not touch parts in this area because there is a danger of getting burned Label 1 High voltage inside NEVER touch parts
16. articularly effective if accomplished prior to seasons of high humidity Consult with your service representative in regard to the cost of cleaning the internal parts of the copier Q o Other precautions DO NOT place heavy objects on the copier or cause other damage to the copier DO NOT open the front cover turn off the main switch or pull out the power plug during copying During copying some ozone is released but the amount does not cause any ill effect to one s health If however the copier is used over a long period of time in a poorly ventilated room or when making an extremely large number of copies the smell may become unpleasant To maintain the appropriate environment for copy work it is suggested that the room be properly ventilated When lifting or moving the copier contact your Service representative Do not touch electrical parts such as connectors or printed circuit boards They could be damaged by static electricity DO NOT attempt to perform any operations not explained in this handbook CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Do not open any cover or turn the power off while the motor inside can be heard regardless of the condition of the copier E Cautions when handling consumables
17. ause burns A WARNING High voltage is present in the charger section Take sufficient care when working in this area as there is a danger of electrical shock A CAUTION Do not incinerate toner and toner containers Dangerous sparks may cause burns 3 6 CHAPTER 3 PREPARATIONS BEFORE USE 4 Slide the toner container to the left and then pull it out toward 6 Hold the new toner container vertically and tap the top 15 times Turn the container upside down and tap the top 15 times Then hold the container horizontally and shake it from side to side 10 times you Zaw A WARNING High voltage is present in the charger section Take sufficient care when working in this area as there is a danger of electrical shock 5 Gently pull the cleaning shaft out as far as it will go and push 7 Install the toner container First insert the toner container into the copier as far as it will it back in 2 to 3 times go and then slide it to the right as indicated by the marked arrows IMPORTANT Do not pull the cleaning shaft with force or pull it out completely 3 7 8 Install the waste toner tank NOTE If the waste toner tank is not installed correctly the front cover will not close Close the front cover Toner replenishment requires 2 to 3 minutes NOTE If the Add Toner indicator does not turn off 2 to 3 minutes after the start of toner replenishment repeat step 6 CHAPTER 3 PREPARAT
18. ed to step 15 8 English text panel Symbol panel Zoom Input Enter 5 5 When the report is printed out the display returns to that for step 2 To make other settings perform the respective procedures see below To end the making of default settings proceed to step 17 Enter the paper width by pressing the Number of Copies Zoom key or Number of Copies Zoom key The paper width can be set from 4 13 to 8 50 105 to 216 mm Inch specifications Metric specifications Press the Zoom Input Enter key The display returns to that for step 2 To end the making of default settings proceed to step 17 Enter the copy limit 99 copies or lower by pressing the Number of Copies Zoom key or Number of Copies Zoom key English text panel Symbol panel Number of Number of Copies Copies Qo Input Enter E E Press the Zoom Input Enter key The display returns to that for step 2 To end the making of default settings proceed to step 17 9 10 11 12 13 Press the Start key The image pattern shown in the illustration will be printed out When adjusting paper feed shifting of the multi bypass be sure to use 8 1 2 x 11 letter A4 paper Image center Fold the paper precisely into two to obtain the center line of the paper and then compare it with the center line of the image Adjust the value using the Number o
19. ed to take adequate measures The above warning is valid only in Australia and New Zealand DECLARATION CONFORMITY TO 89 336 EEC 73 23 EEC and 93 68 EEC We declare under our sole responsibility that the product to which this declaration relates is in conformity with the following specifications Limits and methods of measurement for immunity characteristics of information technology equipment ENS5024 Limits and methods of measurement for radio interference characteristics of information technology equipment ENS5022 Class Limits for harmonic currents emissions for equipment input current S 16A per phase EN61000 3 2 Limitation of voltage fluctuations and flicker in low voltage supply systems for equipment with rated current S 16A EN61000 3 3 Safety of information technology equipment including electrical equipment EN60950 Radiation Safety of laser products equipment classification requirements and user s guide EN60825 1
20. en the total number of copies is 1 234 001 234 The total counter value can also be checked in the following way CD Hold down the Stop Reset key for 5 seconds 2 The total counter value is displayed Toner counter report Prints a report on the toner consumption ratio Using this toner consumption ratio you can manage when the toner container needs replacing If the toner consumption ratio is very high it is recommended to combine the use of the economy mode page 4 1 with the regular use Toner replacement message output setting When the toner is used up and toner container replacement is required a message requesting the user to replace the toner container will be printed Select OFF when not printing the message Paper feed shifting adjustment Adjusts displacement of the copy image 3 0 to 3 0 0 in increments of 0 1 Paper feed shifting adjustment multi bypass Adjusts displacement of the copy image Be sure to use 8 1 2 x 11 letter A4 paper 3 0 to 3 0 0 in increments of 0 1 Inch metric specifications setting Switches the copier specifications setting between inch and metric Since the specifications setting is made at the factory it is not necessary to make this setting under normal circumstances If A and 011 alternate on the copy quantity display the copier initializes the data to remedy an error If this occurs make the specificati
21. f Copies Zoom key or Number of Copies Zoom key Adjustment can be made between 3 0 and 3 0 changing the value by 0 1 moves the image center line by 0 1 mm oH gt gt If the image looks like 1 increase the value If the image looks like 2 decrease the value Press the Zoom Input Enter key The display returns to that for step 2 To end the making of default settings proceed to step 17 Set the length of folio 200 to 216 mm by pressing the Number of Copies Zoom key or Number of Copies Zoom key English text panel Symbol panel Number of Copies Copies 9 Zoom Q Input Enter Number of 14 15 16 17 CHAPTER 5 COPIER DEFAULT SETTING Press the Zoom Input Enter key The display returns to that for step 2 To end the making of default settings proceed to step 17 The setting code changes each time the Number of Copies Zoom key or Number of Copies Zoom key is pressed Select a setting code by referring to the table shown in 1 Default settings Symbol panel English text panel Number of Number of Copies Copies 9 Zoom Input Enter Press the Zoom Input Enter key The display returns to that for step 2 To end the making of default settings proceed to the next step When F00 appears press the Zoom Input Enter key The display indication changes from the default code to the numbe
22. h of time from when the copier is not used to when the auto shut off function page 4 4 turns the main switch OFF automatically The auto shut off function can also be turned OFF If turned OFF this setting cannot be made see Auto shut off This setting item will not be displayed if OFF is selected for Auto shut off t is recommended to set a long period of time to trigger the auto shut off if the copier is used frequently and set a short period of time if the copier is used only occasionally For how to cancel the auto shut off function see Auto shut off 15 minutes 30 minutes 45 minutes 60 minutes 75 minutes 90 minutes 105 minutes 120 minutes Preheat recovery time Selects the mode of the energy saver auto preheat function page 4 4 from the recovery priority mode and power save priority mode The length of time that the Copier uses to recover from the energy saver auto preheat function can be selected between within 10 seconds recovery priority mode and within 30 seconds power save priority mode 1 Recovery priority mode 2 Power save priority mode Default code Setting item CHAPTER 5 COPIER DEFAULT SETTING Setting contents Setting code F17 Viewing total counter value Displays the total number of copies made The total number of copies are displayed on the copy quantity display three digits at a time Example Wh
23. ical shock When J96 J98 or JOO is displayed see page 6 2 A CAUTION The copier s fixing unit is extremely hot Take sufficient care when working in this area as there is a danger of getting burned Do not reuse misfed paper If paper is torn during removal be sure to remove all loose scraps from inside the copier or they could cause misfeed later After misfed paper has been removed warm up will begin The misfeed indicator will turn off and the copier will return to the same settings prior to the misfeed 6 3 CHAPTER 6 WHEN A PROBLEM OCCURS 3 Removal procedures Misfeed in multi bypass If the multi bypass indicator flashes green when the multi bypass is Misfeed in paper feed section used a misfeed has occurred in the multi bypass Remove the misfed Misfeed in drawer paper using the procedure given below If the drawer indicator flashes green when the drawer is used a misfeed has occurred in the drawer Remove the misfed paper using 1 Remove all the paper remaining in the multi bypass the procedure given below 4 Open the drawer 2 Check that the indicator showing the location of the paper misfeed has turned off and re load the paper into the multi bypass Remove the misfed paper while taking care not to tear it f the paper should be torn remove all the scraps from the 2 Misfeed in left cover inside the copier If the misfeed indicator lights red a mi
24. ification display with 96 lit English text panel Symbol panel Change the displayed zoom ratio using the Number of Copies Zoom key or Number of Copies Zoom key English text panel Symbol panel Number of Number of Copies Copies e Zoom Input Enter 9 6 Press the Zoom Input Enter key The zoom ratio will be set and the display indication changes from the magnification to the number of copies English text panel Symbol panel Input Enter 2 Standard zoom copy Copying is possible using the ratios preset in the copier Available ratios Inch specifications 200 129 5 1 2 x 8 1 2 gt 8 1 2 x 11 100 Initial setting 78 8 1 2 x 14 gt 8 1 2 x 11 5096 Metric specifications 200 141 A5 gt A4 100 Initial setting 7096 A4 gt A5 50 1 Press the Size Select key The zoom ratio appears on the copy magnification display with lit Inch specifications Metric specifications MAX MAX 129 54x814 84x11 Ab gt A4 Full Size 1 1 BuX14 gt 81X11 AA A5 78 2 Each time you press the Size Select key the standard zoom ratios appear on the copy magnification display in order Display the desired zoom ratio English text panel Symbol panel Input Enter 3 Press the Zoom Input Enter key The zoom ratio will be set and the display indication changes from the magnification to the number of copies CHAPTER 4 BASIC O
25. in this area because there is a danger of electric shock NOTE DO NOT remove these labels A INSTALLATION PRECAUTIONS E Environment E Power supply Grounding the copier A CAUTION A WARNING Avoid placing the copier on or in locations which are DO NOT use a power supply with a voltage other unstable or not level Such locations may cause the than that specified Avoid multiple connections in the copier to fall down or fall over This type of situation same outlet These types of situations present a presents a danger of personal injury or damage to the danger of fire or electrical shock pol E Plug the power cord securely into the outlet If Avoid locations with humidity or dust and dirt If dust metallic objects come in contact with the prongs on or dirt become attached to the power plug clean the the plug it may cause a fire or electric shock Q plug to avoid the danger of fire or electrical shock Always connect the copier to an outlet with a ground Avoid locations near radiators heaters or other heat connection to avoid the danger of fire or electrical sources or locations near flammable items to avoid shock in case of an electric short If an earth the danger of fire connection is not possible contact your service representative
26. l Symbol panel V OAutoExp OText amp Photo OPhoto When the Auto Exp Text amp Photo Photo and Text indicators are all turned off the copier is in the economy mode In the economy mode the image density becomes lighter to reduce toner consumption Use this mode when high quality printing is not required Symbol panel English text panel OText amp Photo ofr OPhoto odil OText Lighter Darker m mp O O00000 O 5 Copy exposure adjustment Copy exposure can be selected for all the image modes excluding the auto exposure mode To make the copy density darker press the right copy exposure adjustment key to move the indication on the exposure scale to the right to make the copy density lighter press the left copy exposure adjustment key to move the indication on the exposure scale to the left The number of exposure adjustment levels can be selected from 3 and 5 see Exposure steps on page 5 1 English text panel Symbol panel Number of Number of 6 Setting the number of copies Pressing the Number of Copies Zoom key increases the number of copies and pressing the Number of Copies Zoom key decreases the number of copies If you hold down the Number of Copies Zoom key for approximately 2 seconds when the number of copies is 1 the number jumps to 99 if you hold down the Number of Copies Zoom key for approximately 2 sec
27. ll automatically be printed out The copier initializes the data to remedy the error Make the specifications setting F22 Inch metric specifications setting before using the copier again If the same indication appears again or if the same indication appears frequently contact your service representative The error message is as follows Default data was initialized Need initial setting to use the machine Input F22 User Code cf User manual The Add Toner indicator lights Making one copy at a time is still possible for some time with the indicator lighting but it will eventually be disabled Replace the toner container and wasted toner tank as soon as possible If you replace the toner container with the main switch turned OFF the Add Toner indicator may not go out In this case open and close the front cover AP appears on the copy quantity display Toner is being replenished inside the copier Wait a few minutes Although the lamp under the platen may remain lit while AP is displayed it is not a problem PF appears on the copy quantity display A paper misfeed occurred in the drawer of the flashing indicator Remove the misfed paper The drawer of the flashing indicator is not inserted correctly Close the drawer securely There is no paper in the drawer of the flashing indicator Load paper E07 appears on the copy quantity display The set paper size is different from that of the paper u
28. move the power plug from the outlet when performing cleaning operations Lift open the original cover Wipe the shaded areas shown in the below illustrations with a soft cloth dampened with alcohol or a mild detergent Never use thinner or other organic solvents for this purpose CHAPTER 7 CLEANING AND SPECIFICATIONS 2 Specifications Huq Desk top Original table siira Fixed type COPYING SVSTENI erede eter Indirect electrostatic Originals reitera m tereti maie Sheets of paper books 3 dimensional objects Maximum original size 8 1 2 x 14 folio COPY SIZES cedente da 8 1 2 x 14 8 1 2 x 11 5 1 2 x 8 1 2 A4 A5 vertical A6 vertical folio Print margin loss 0 5 5 5 mm COPYING Speed temen ks Same size copying 8 1 2 x 11 A4 15 copies min tlie pe Paco rab Within 30 seconds at room temperature of 68 F 20 C humidity 65 RH From energy saver auto preheat mode Within 10 seconds priority to recovery within 30 seconds priority to power save at room temperature of 68 F 20 C humidity 6596 RH First COPY SPCC fei oisi es nei n rs Approximately 6 3 seconds 8 1 2 x 11 A4 ZOOM or EP sensi Any ratio between 50 and 200 in increments of 196 Resolution nter enne eie Reading 600 x 600 dpi Writing 600 x 600 dpi Paper feed system erret Automatic feeding from the drawer 1 drawer capacit
29. n Copies come out too dark Is the copier in the auto exposure mode To change the overall exposure perform auto exposure adjustment Is the copier in the Photo Text amp Photo or Text mode Adjust the exposure to the correct degree using the copy exposure adjustment keys To change the overall exposure perform the exposure adjustment for each mode Copies are dirty Is the platen dirty Clean the platen Open the front cover pull out and push back in the cleaning shaft Copy image is askew Are the originals set correctly When setting an original on the platen be sure to align a corner of it with the rear left corner of the platen Misfeed occurs frequently Is the paper set correctly in the drawer Set paper properly Is paper curled folded or wrinkled Replace the paper with new paper Is there any misfed paper or loose scraps of paper remaining inside the copier Carry out the appropriate procedure to remove the paper Is the set paper size different from that of the paper used Set the paper size to the size of the actual paper or use a paper of the set size The Add Toner indicator does not turn off after toner replenishment Has the new toner container been shaken sufficiently Shake the toner container again CHAPTER7 CLEANING AND SPECIFICATIONS 1 Cleaning the copier A CAUTION For safety purposes ALWAYS re
30. ng enabled English text panel Symbol panel Zoom Input Enter 3 4 CHAPTER 3 PREPARATIONS BEFORE USE 2 How to set originals 1 Setting an original on the platen 1 Set the original with the side to be copied facing downward Be sure to align a corner of the original with the rear left corner of the platen 3 5 CHAPTER 3 PREPARATIONS BEFORE USE 3 Replacing the toner container waste toner tank When the level of toner becomes low the Add Toner indicator lights 1 Open the front cover and a toner replacement message is printed out When the message is printed replace the toner container and waste toner tank immediately It is still possible to make copies one at a time with the indicator lit However if copying is continued under this condition the Start indicator will eventually go off and copying will become disabled Be sure to replace the waste toner tank when replacing the toner container Use the new waste toner tank that is supplied with the toner container The toner replacement message is as follows Replace waste toner tank at the time of toner container exchange surely and do charge wire cleaning Replenish toner only when the Add Toner indicator is lit Replace the toner container with the main switch turned ON 2 Remove the waste toner tank English text panel Symbol panel A CAUTION Do not incinerate toner and toner containers Dangerous sparks may c
31. occurs 5 Multi Bypass Load paper here when copying onto small size or special paper Insert guides Align the guides with the paper width when loading paper on the multi bypass Support guide Pull out when loading paper into the multi bypass Toner container Waste toner tank Cleaning shaft Pull out and push back in several times after toner container replacement or when copy images are soiled with toner Front cover Open to replace the toner container and waste toner tank Main switch Turn ON before starting to make copies 93 Copy storage section Copied paper is stored here Drawer Holds up to 250 sheets of standard paper standard paper as specified by our company 49 Platen Set originals here for copying Place originals face down with the edges aligned with the size scales on the left and rear sides of the platen Original size scales Be sure to align the original with these when setting the original on the platen Length guide Adjust to the length of the paper to be set in the drawer Width guide Adjust to the width of the paper to be set in the drawer Width adjustment lever Hold the lever and adjust the width guide to the width of the paper to be set in the drawer 9 Length guide storage section Store the length guide here when it is not used 3 Drawer bottom plate Push down when loading paper Handles for transport The handles are located on the right and left sides
32. of the copier Hold these two handles when moving the copier CHAPTER 2 NAMES OF PARTS 2 2 CHAPTER 2 NAMES OF PARTS Inch specifications Paper Select D European metric specifications MAX Stop Start Reset 54X81 84X11 Full Size BUX14 gt 8X11 Number of Number of Copiesl MIN Cancel Zooml Z Zoom Size Select oom Input Enter mx d A5 gt A4 1 1 4 gt MIN e E Asia and Oceania metric specifications a OAutoExp Add OText amp Photo Toner OF hote OText Ors Lighter Darker _ PT mp e O Paper Start N MAX Stop Reset AS P AS 11 A4 A5 Number of Number of Copiesi 5 MIN Cancel Go Size Select T D 2 3 Zooml 2 Zoom Input Enter 2 Operation panel CD Start key indicator Press to start copying Copying is possible when the indicator is lit green Stop Reset key Stop Interrupts or aborts copying and printing Reset Cancels settings and returns the copier in the initial mode 3 Size Select key Press when copying using the standard zoom mode See page 4 3 Number of Copies Zoom key Press to increase the number of copies or magnification ratio 5 Number of Copies Zoom key Press to decrease the number of copies or magnification ratio 6 Zoom Input Enter key Press
33. onds when the number of copies is 99 the number jumps down to 1 Display the desired number of copies on the copy quantity display The number of copies can be set to up to 99 It is possible to lower the limit on the number of copies that can be set at a time see Copy limit on page 5 2 CHAPTER 4 BASIC OPERATIONS English text panel Symbol panel Stop Start Q CA 8 Starting copying Press the Start key Copying is possible when the indicator is lit green 9 At the end of copying Copied sheets are ejected onto the copy storage section Up to 100 sheets of standard paper 80 g m can be stored Note that the number of sheets that can be stored varies depending on the condition of the paper used 7 Setting originals Set the original on the platen see 2 How to set originals on page 3 5 A CAUTION If the copier will not be used for a short period of time overnight etc turn the main switch OFF O If it will not be used for an extended period of time vacations etc remove the power plug from the outlet for safety purposes during the time the copier is not in use 4 2 CHAPTER 4 BASIC OPERATIONS 2 Enlargement reduction 1 Zoom copy The zoom ratio can be set to any value from 50 to 200 in 1 increments 1 3 4 3 200 Press the Zoom Input Enter key The zoom ratio appears on the copy magn
34. ons setting 1 Inch 2 Metric 3 Metric Japan Folio length setting drawer When folio is selected as the paper size this sets the length of folio This setting item is available only when metric is selected for the copier specifications 1 210 2 216 Folio length setting bypass When folio is used this sets the length of folio This setting item is available only when metric is selected for the copier specifications 200 to 216 mm 210 mm CHAPTER 5 COPIER DEFAULT SETTING 2 How to make default settings 1 Hold down both of the copy exposure adjustment keys for 3 4 seconds F00 default code appears on the copy quantity display English text panel Symbol panel e AutoExp OText amp Pho OPhoto OText Lighter Darker hus 2 The default code changes each time the Number of Copies Zoom key or Number of Copies Zoom key is pressed Select a default code by referring to the table shown in 1 Default settings English text panel Symbol panel 6 Number of Number of Copies Copies 3 Press the Zoom Input Enter key If F01 or F18 is selected a report will be printed out Proceed to step 4 If F10 is selected proceed to step 5 If F11 is selected proceed to step 7 If F20 or F21 is selected proceed to step 9 If F24 is selected proceed to step 13 If a code other than the above is selected proce
35. r In the normal operation of the product by user no radiation can leak from the machine This machine is classified as Class 1 laser product under IEC 825 CAUTION Performance of procedures other than those specified in this manual may result in hazardous radiation exposure This label is attached to the laser scanner unit inside the machine and is not in a user access area DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM CAUTION INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM ATTENTION RAYONNEMENT LASER INVISIBLE SI OUVERT DANGEREUX DE REGARDER A L INTERIEUR VORSICHT UNSICHTBARE LASERSTRAHLEN WENN GEOFFNET NICHT HINENSEHEN V A TYPE 2A11301 INPUT 24VDC MAX 1 8A WAVE LENGTH 765 795nm 5VDC 0 30A LASER SOURCE 5mW gt PS lt The labels shown below are attached on the rear side of the machine CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT E1 CAUTION The power plug is the main isolation device Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source VORSICHT Der Netzstecker ist die Hauptisoliervorrichtung Die anderen Schalter auf dem Ger t sind nur Funktionsschalter und k nnen nicht verwendet werden um den StromfluB im Ger t zu unterbrechen WARNING This is Class A product In a domestic environment this product may cause radio interference in which case the user may be requir
36. r of copies English text panel Symbol panel Number of Number of Copies Copies 9 Zoom Input Enter You can also end the making of default settings by pressing the Stop Reset key Q CA 5 6 CHAPTER6 WHEN A PROBLEM OCCURS 1 Error status indications When any of the indications listed in the table below appears on the operation panel take the corrective action as instructed P MAX Q CA 4 X 9 Ga ABP AA Q 11 Dh CD aas MIN Indication Action A and 100 alternate on the copy quantity display Turn the main switch OFF and ON and check that the lamp under the platen turns on during copying If the lamp turns on leave the power turned on for approximately 1 hour If the same indication appears again contact your service representative If the lamp does not turn on contact your service representative C and 610 620 630 or 710 alternate on the copy quantity display Contact your service representative A and 310 400 401 or 510 alternate on the copy quantity display Turn the main switch OFF and ON If the same indication appears again contact your service representative CHAPTER 6 WHEN A PROBLEM OCCURS Indication Action A and 011 alternate on the copy quantity If this indication appears turn the main switch OFF and ON An error message display wi
37. rolonged period of time remove the paper from the drawer and seal it in the paper storage bag to protect it from moisture 3 Loading paper into the multi bypass Standard paper 60 160 g m standard paper as specified by our company colored paper and special paper can be loaded into the multi bypass The multi bypass can hold up to 50 sheets of standard paper of 64 to 80 g m Inch specifications The multi bypass can hold paper of any size from 8 1 2 x 14 legal to 5 1 2 x 8 1 2 vertical Metric specifications The multi bypass can hold paper of any size from folio to A6 vertical The types of special paper that can be used with the multi bypass and the number of sheets that can be loaded are as follows Transparencies 1 sheet Standard paper 160 g m 1 sheet When copying onto special paper be sure to use the multi bypass 1 Open the multi bypass 3 2 CHAPTER 3 PREPARATIONS BEFORE USE 2 Pull out the support guide 3 Adjust the insert guides to the width of the paper to be loaded 3 3 IMPORTANT When loading paper into the multi bypass make sure that the copy side is facing downward The copy side is the side facing upward when the package is opened If the leading edge of the paper is curled straighten it out before loading the paper in the multi bypass Do not leave paper loaded in the multi bypass when it is not used If you do a paper misfeed may occur When
38. sed Check the paper size setting and the actual paper size and set the paper size to the size of the actual paper or use a paper of the set size E30 appears on the copy quantity display The tape in the developing section has not been removed See the installation manual J96 J98 or JOO appears on the copy Open the drawer and left cover and check for any misfed paper If the same quantity display indication appears contact your service representative OP appears on the copy quantity display The front or left cover is open Close the cover CHAPTER 6 WHEN A PROBLEM OCCURS 2 When paper misfeeds If a paper misfeed occurs copying will stop An indication signaling a paper misfeed appears on the operation panel and an indicator lights showing the location of a paper misfeed Remove the misfed paper by referring to 3 Removal procedures on page 6 4 with the main switch in the ON position 1 Misfeed location indications 2 Cautions Misfeed in paper feed section page 6 4 PF appears on the copy quantity display and the drawer indicator or multi bypass indicator flashes green WARNING 2 Misfeed in left cover page 6 4 High voltage is present in the charger section Take 020 J22 J40 J50 or J95 appears on the copy quantity sufficient care when working in this area as there is a display and the misfeed indicator lights red danger of electr
39. sentative DO NOT remove or connect the power plug with wet hands as there is a danger of electrical shock ALWAYS contact your service representative for maintenance or repair of internal parts A CAUTION DO NOT pull the power cord when removing it from the outlet If the power cord is pulled the wires may become broken and there is a danger of fire or electrical shock ALWAYS grasp the power plug when removing the power cord from the outlet ALWAYS remove the power plug from the outlet when moving the copier If the power cord is damaged there is a danger of fire or electrical shock If the copier will not be used for a short period of time overnight etc turn the main switch OFF O If it will not be used for an extended period of time vacations etc remove the power plug from the outlet for safety purposes during the time the copier is NONIN USOE c c etico ere erp pee ALWAYS hold the designated parts only when lifting or moving the copier For safety purposes ALWAYS remove the power plug from the outlet when performing cleaning ME If dust accumulates within the copier there is a danger of fire or other trouble It is therefore recommended that you consult with your service representative in regard to cleaning of internal parts This is p
40. sfeed has occurred in the left cover Remove the misfed paper using the procedure given below 1 Open the multi bypass Close the drawer slowly Check that the paper is kept under the claw of the drawer If not reload the paper 6 4 CHAPTER 6 WHEN A PROBLEM OCCURS IMPORTANT The drum 1 is highly sensitive to light and dirt Be careful not to expose it to strong light such as room lighting or to touch the drum with the hands A WARNING High voltage is present in the charger section Take sufficient care when working in this area as there is a danger of electrical shock A CAUTION The copier s fixing unit is extremely hot Take sufficient care when working in this area as there is a danger of getting burned 3 Holding the green handles lower the two fixing section release levers 5 Holding the green handle open the ejection guide 4 Remove the misfed paper while taking care not to tear it If the paper is not easy to remove proceed to the next step If the paper is removed successfully proceed to step 9 If the paper should be torn remove all the scraps from the inside the copier A CAUTION The copier s fixing unit is extremely hot Take sufficient care when working in this area as there is a danger of getting burned 6 Remove the misfed paper while taking care not to tear it 7 Close the ejection guide NOTE If the fixing section release levers are lowered the
41. verall exposure when using the auto exposure mode The larger the setting code number the darker the copy density Text and photo original exposure Adjusts the exposure for when text and photo original is adjustment selected for the image mode The larger the setting code number the darker the copy density Default code Setting item CHAPTER 5 COPIER DEFAULT SETTING Setting contents Setting code F06 Photo original exposure adjustment Adjusts the exposure for when photo original is selected for the image mode The larger the setting code number the darker the copy density 1 Light 2 87 14 Text original exposure adjustment Adjusts the exposure for when text original is selected for the image mode The larger the setting code number the darker the copy density 2 14 5 Dark Drawer paper size Sets the size of paper loaded in the drawer Inch 1 8 1 2 x 14 2 8 1 2 t1 3 5 1 2 8 1 2 1 A4 2 5 3 Folio Turning multi bypass non standard size paper setting ON OFF Set to ON when using non standard size paper with the multi bypass Non standard size paper width setting for multi bypass Sets the paper width for the multi bypass to use non standard size paper The maximum paper length is 14 355 6 mm This setting item will not be displayed if OFF is selected in Turning multi bypass non standard size
42. when copying using the zoom copy mode See page 4 3 Copy quantity magnification display Displays the number of copies to be made and magnification ratio for reduction enlargement copying When displaying a magnification ratio will light Add Toner indicator Lights when the level of toner becomes low See page 3 6 9 Paper Select key Press to select a drawer or the multi bypass The indicator for the selected paper source will light Drawer indicator Lights when the drawer is selected flashes when a paper misfeed occurs or paper is used up Multi bypass indicator Lights when the multi bypass is selected see page 3 3 flashes when a paper misfeed occurs or paper is used up Misfeed indicator Lights when a misfeed occurs Image mode selection key Press to select the type of the original Copy exposure adjustment keys Press the left key to make the copy density lighter press the right key to make it darker Initial mode at the end of warm up or when the Reset key is pressed In the initial mode the drawer is selected as the paper source the number of copies is set to 1 and the image mode is set to Text amp Photo The image mode selected in the initial mode can be changed see Image mode on page 5 1 Auto clear function About 90 seconds after copying stops the copier will automatically return to the same settings as those after warm up However the exposure mode will not change
43. y 250 sheets 80 g m standard paper as specified by our company and multi bypass capacity 50 sheets 80 g m standard paper as specified by our company PAPET Drawer Standard paper 64 80 g m Multi bypass Standard paper 60 160 g m special paper colored paper letterhead etc Continuous COPYING sei eiecti mes 1 99 sheets Light source Rare gas lamp Developing system 2 componet reverse developing Fixing system Heat roller Cleaning system Blade PhotoGOndUclor ci iit ec em REED een OPC FUNCTIONS and modes nr rrt nre Auto exposure adjustment photo mode economy mode zoom copy mode standard zoom mode auto shut off function energy saver auto preheat function self diagnosis function POWGF SOURCE 1 iiie ds tries 120 V AC 60 Hz 9A 220 240 V AC 50 60 Hz 4 8 A average 2 5 A Dimensions 19 9 16 W x 19 9 16 D x 14 13 16 H 497 mm W x 497 mm D x 376 mm H Approx 46 2 Ibs 21 kg NOIS6 emlsSlOTn ir o EE 70 dB A TE 27 3 16 W x 19 9 16 D 691 mm W x 497 mm D Specifications are subject to change without notice 7 2 Laser Safety Laser radiation could be hazardous to the human body For this reason laser radiation emitted inside this machine is hermetically sealed within the protective housing and external cove
Download Pdf Manuals
Related Search