Home

Network Operating Instructions

1. 15 fps 30 fps Default setting 5 fps Note When ON is selected for MPEG 4 transmission the refresh intervals may be longer than the set value when the setting value with an asterisk on the right is selected Image capture size Select QVGA or VGA for the image capture size of JPEG images Default setting VGA Image quality Select image quality of JPEG images from the following O Super fine 1 Fine 2 3 4 5 Normal 6 7 8 9 Low Default setting 5 Normal 21 E MPEG 4 setup Configure the settings relating to MPEG 4 image such as Max bit rate per 1 client Image capture size Image quality etc in this section Refer to page 21 for further information about the settings relating to JPEG images Network Camera WV NF284 WV NF284000 Unicast port AUTO 04 D 3004 5 04 4 7 fe JE MPEG 4 transmission Select ON or OFF to determine whether or not to transmit MPEG 4 images ON Transmits MPEG 4 images OFF Does not transmit MPEG 4 images Default setting ON Note When ON is selected for MPEG 4 transmission displaying rather of MPEG 4 image or JPEG image will be available However the refresh interval JPEG may be longer than the set value when dis playing JPEG images Max bit rate per 1 client Select a MPEG 4 bit rate per a client from the following 64 kbps 128 kbps 256 kbps 512 kbps 1024 kbps 1536 kbps 2048 kbps 3072 kbps
2. Authentication setup 6 Authentication setup button Server setup Network setup Maintenance 7 Server setup button Network setup button Help 9 Maintenance button Help button Live button The Live page will be displayed D Basic setup button Click this button to display the Basic setup page The basic settings such as time and date and cam era name and the settings relating to the NTP serv er and the SD memory card can be configured on the Basic setup page Refer to page 17 for further information GEE Camera setup button Click this button to display the Camera setup page The settings relating to image from the camera such as image quality and brightness and the settings relating to audio can be configured on the Camera setup page Refer to page 21 for further informa tion O Multi screen setup button Click this button to display the Multi screen setup page The cameras to be used for the multi screen display can be registered on the Multi screen setup page Refer to page 26 for further information ft Internet Explorer e Eek h 2006101101 0 00 Status display area SD memory card WV NF284 2006 v 7 01 v 01 v v 100 12 hours 24 hours 2 Setup page MM DDAYYYY v OON ON e QE Alarm setup button Click this button to display the Alarm setup page The settings relating
3. EE The letters MPEG 4 on the button will turn green and an MPEG 4 image will be displayed When OFF is selected for MPEG 4 transmission on the setup menu the MPEG 4 button will not be dis played page 22 GEG The letters JPEG on the button will turn green and JPEG image will be displayed 5 Image capture size buttons These buttons will be displayed only when a JPEG image is displayed GEE The letters VGA on the button will turn green and images will be displayed in VGA size Ew The letters QVGA on the button will turn green and images will be displayed in QVGA size ZOOM buttons 2 Le The zoomed image will be zoomed out Image displayed in the original size cannot be zoomed out The zoomed image will return to the original size a The displayed image will be zoomed in Note When ON is selected for VMD alarm page 27 the displayed images will not be zoomed in 7 Brightness buttons 2 The displayed image will be darker The adjusted brightness will return to the default brightness page 24 a The displayed image will be brighter AUX buttons 2 foem The AUX connector will open tose The AUX connector will close 9 Camera name The set camera name will be displayed Alarm occurrence indication button 2 This button will be displayed and will blink when an alarm occurred When the button is clicked the but ton will disappear and the ala
4. j _ Full TER ET N ssn EET T heini Teer Disable all DirectDraw and DirectsD accelerations as well as all cursor and advanced drawing accelerations Use this setting to corect severe problems with Direct accelerated applications Enable write combining When using a PC on which Windows XP Service Pack2 SP2 is installed The following may occur during operation when using a PC on which Windows XP Service Pack2 SP2 is installed Follow the instructions below when the following occurred By performing the following solutions other applications and the security level may not be affected The Information Bar expressed in the following symptom and solutions will be displayed just below the address bar only when there is information to communicate index Microsoft Internet Explorer PeR ar Fie Edit View Favorites Tools Help r a gt gt ws i Q e gt x a Yo Search Ke Favorites Ea vas 38 Address http 192 168 0 100 vo n 6 Pop up blocked To see this pop up or additional options click here The following message is e Click the information bar and select Always Allow displayed on the information Pop ups from This Site The dialog window saying bar Allow pop ups from this site will be displayed Click Pop up blocked To see this the Yes button pop up or additional options click here baat x lt Information Bar Reference The following message is Click
5. will be applied to the size of the image to be attached E E mail notification setup Destination address Enter the destination mail address Up to 4 destination addresses can be registered To notify by e mail when an alarm occurred check the Alarm checkbox respective to the desired address To provide notification by e mail when any of the follow ing has occurred check the Diag checkbox respective to the desired address When notification of the remaining space of the SD memory card has been provided page 19 When the SD memory card has become full When mounting of the SD memory card failed To delete the registered address click the DEL button respective to the desired address Number of characters for the destination mail address 3 128 characters Mail subject Enter the mail subject Number of characters for the mail subject 0 50 characters Mail body Enter the mail body Number of characters for the mail body 0 200 char acters Note Notification mail will be sent with the following mes sage The message to be sent differs depending on the status of the SD memory card e The SD memory card is full This message will be sent when the SD memory card becomes full e The SD memory card cannot be recognized This message will be sent when the SD memory card has failed to mount Configure the settings relating to Panasonic alarm protocol Click the Notification tab on t
6. 1 250 pics Approx 625 pics rnond O spom 8 Approx 22 000 pics Approx 11 000 pics Approx 5 500 pics Approx 2 750 pics Approx 1 375 pics Approx 687 pics Image capture size QVGA Size of SD Approx 26 000 pics Approx 13 000 pics Approx 6 500 pics Approx 3 250 pics Approx 1 625 pics Approx 812 pics Approx 28 000 pics Approx 14 000 pics Approx 7 000 pics Approx 3 500 pics Approx 1 750 pics Approx 875 pics Image quality Approx 30 000 pics Approx 15 000 pics Approx 7 500 pics Approx 3 750 pics Approx 1 875 pics Approx 937 pics Approx 32 000 pics Approx 16 000 pics Approx 8 000 pics Approx 4 000 pics Approx 2 000 pics Approx 1 000 pics memory card 0 Super fine 1 Fine a A Approx 24 000 pics Approx 12 000 pics Approx 6 000 pics Approx 3 000 pics Approx 1 500 pics Approx 750 pics Size of SD Approx 26 000 pics Approx 13 000 pics Approx 6 500 pics Approx 3 250 pics Approx 1 625 pics Approx 812 pics Approx 27 000 pics Approx 13 500 pics Approx 6 750 pics Approx 3 375 pics Approx 1 687 pics Approx 843 pics Image quality Approx 28 000 pics Approx 14 000 pics Approx 7 000 pics Approx 3 500 pics Approx 1 750 pics Approx 875 pics Approx 30 000 pics Approx 15 000 pics Approx 7 500 pics Approx 3 750 pics Approx 1 875 pics Approx 937 pics mowed O snom 8 O r o o f o Approx 32 000 pics Approx 16 000 pics Approx 8 000 pics
7. Approx 4 000 pics Approx 2 000 pics Approx 1 000 pics 20 Approx 36 000 pics Approx 18 000 pics Approx 9 000 pics Approx 4 500 pics Approx 2 250 pics Approx 1 125 pics Approx 38 000 pics Approx 19 000 pics Approx 9 500 pics Approx 4 750 pics Approx 2 375 pics Approx 1 187 pics Approx 40 000 pics Approx 20 000 pics Approx 10 000 pics Approx 5 000 pics Approx 2 500 pics Approx 1 250 pics Approx 42 000 pics Approx 21 000 pics Approx 10 500 pics Approx 5 250 pics Approx 2 625 pics Approx 1 312 pics Configure the settings relating to images and audio Camera setup The settings relating images and audio such as brightness and image quality of JPEG MPEG 4 can configured on this page The Camera setup page has 3 tabs of the JPEG MPEG 4 tab the Camera tab and the Audio tab Configure the settings relating to JPEG MPEG 4 images JPEG MPEG 4 Click the JPEG MPEG 4 tab on the Camera setup page page 15 E JPEG setup Configure the settings such as Refresh interval JPEG Image capture size and Image quality on this page Refer to page 22 for further information about the settings relating to MPEG 4 images s Network Camera WV NF284 WV NF284 2006101101 0 00 A JPEGIMPEG 4 Refresh interval JPEG Select an interval to refresh the displayed JPEG image from the following 0 1 fos 0 2 fos 0 33 fps 0 5 fos 1 fps 2 fps 3 fps 5 fps 6 fps 10 fps
8. a network the alarm action will be performed Action at an Alarm Occurrence Display the Alarm occurrence indication button on the Live page page 5 The Alarm occurrence indication button will be displayed on the Live page at an alarm occurrence Note The Alarm occurrence indication button will be refreshed in 30 seconds intervals For this reason it may take a maximum of 30 seconds until the Alarm occurrence indication button is displayed on the Live page at an alarm occurrence Notify of alarm occurrences to the device connected to the alarm connector It is possible to output signals from the alarm connector on the mounting side of the camera and sound the buzzer when an alarm occurs The settings for the alarm output can be configured on the Alarm tab of the Alarm setup page page 29 Transmit an image onto a server automatically An alarm image can be transmitted at an alarm occurrence to the server designated in advance The settings required to transmit an alarm image to a server can be configured in the Alarm image setup section of the Alarm tab of the Alarm setup page page 28 and the FTP tab of the Server setup page page 37 Notify of alarm occurrences by e mail Alarm mail alarm occurrence notification can be sent at an alarm occurrence to the e mail addresses registered in advance Up to 4 addresses can be registered as recipients of the alarm mail An alarm image still picture can b
9. already in use gt 20 21 23 25 42 53 67 68 69 110 123 161 162 995 10669 10670 DNS Select AUTO or MANUAL to determine whether or not to use the DNS When MANUAL is selected it is necessary to configure the settings for the DNS When using the DHCP function it is possible to obtain the DNS address automatically by selecting AUTO Refer to the network administrator for further information about the settings Default setting MANUAL Primary DNS Secondary DNS When MANUAL is selected for DNS enter the IP address of the DNS Refer to the network administrator about the IP address of the DNS Line speed Select the line speed for data transmission from the fol lowings It is recommended to use the default setting AUTO AUTO Line speed will be applied automatically 100MF 100 Mbps full duplex 100MH 100 Mbps half duplex 10MF 10 Mbps full duplex 10MH 10 Mbps half duplex Default setting AUTO FTP access Select Allow or Forbid to determine whether to allow or forbid the FTP access Default setting Forbid Total bit rate Select the total bit rate for data transmission from the followings 64 kbps 128 kbps 256 kbps 512 kbps 1024 kbps 2048 kbps 4096 kbps Unlimited Default setting Unlimited Notes e When selecting 64 kbps select OFF for Mic mode on the Audio tab s page 25 e When 64 kbps is selected it is impossible to carry out the live transmission of J
10. delet ed when the SD memory card is formatted e Do not turn the power of the camera off in the process of formatting 19 e After formatting the SD memory card available size may be smaller than the total size since the default directory is automatically created in the SD memory card e Compatible SD memory card is as follows SD memory card manufactured by Panasonic 64 MB 128 MB 256 MB 512 MB 1 GB 2GB SD High Capacity SDHC card is not compatible with this unit Possible number of images that can be saved on the SD memory card as indications Important They are not actual numbers of images that can be saved on the SD memory card Numbers will differ according to photographic subject settings relating to the SD memory card etc Image capture size VGA Size of SD Image quality memory card 0 Super fine 1 Fine ee ee Approx 10 000 pics Approx 5 000 pics Approx 2 500 pics Approx 1 250 pics Approx 625 pics Approx 312 pics Size of SD Approx 14 000 pics Approx 7 000 pics Approx 3 500 pics Approx 1 750 pics Approx 875 pics Approx 437 pics Approx 16 000 pics Approx 8 000 pics Approx 4 000 pics Approx 2 000 pics Approx 1 000 pics Approx 500 pics Image quality Approx 18 000 pics Approx 9 000 pics Approx 4 500 pics Approx 2 250 pics Approx 1 125 pics Approx 562 pics Approx 20 000 pics Approx 10 000 pics Approx 5 000 pics Approx 2 500 pics Approx
11. failed to transmit using the FTP periodic transmission can be saved automatically on the SD mem ory card To obtain the images saved on the SD memory card use the Windows command prompt or FTP client software The obtained images can be browsed on a PC When using the SD memory REC function of a Panasonic s network disk recorder select OFF for the FTP periodic transmission function page 43 When using the DHCP function images will not be saved on the SD memory card until an IP address is assigned to the camera We make no guarantee for any damages of files on the SD memory card incurred by malfunction or error occur rence in files saved on the SD memory card regardless of what the cause may be Save images on the SD memory card By configuring the following settings saving images which had been failed to transmit to the FTP server using the FTP periodic transmission function will become available About SD memory card Use page 19 File name With time and date page 43 Obtain images on the SD memory card Step 1 Access the camera using the Windows command prompt or FTP client software The window with the user name and password entry fields will be displayed Step 2 Enter the user name whose access level is 1 Administrator and its password Log in the camera Note The default user name with the access level 1 Administrator and its password are as follows User name admin Password 12345 To e
12. the information bar and select Install Active X displayed on the information bar This site might require the following Active X control nwcvssetup exe from Matsushita Electric Industrial Co Ltd Click here to install Unnecessary status bar or scroll bar is displayed on the pop up window Images are not displayed or refreshed smoothly Control The Security Warning window will be displayed Click the Install button on the displayed Security Warning window Click Internet Options on the Tools menu of Internet Explorer and then click the Security tab Then click the Custom Level button to open the Security Setting window Under Miscellaneous select Enable for Allow script initiated windows without size or position constraints Click the OK button The Warning window will be displayed Click the Yes button Delete temporary internet files as follows 1 Select Internet Options from Tools on the menu bar of Internet Explorer The Internet Options window will be displayed Click the Delete Files button in the Temporary Internet files section on the General tab Matsushita Electric Industrial Co Ltd Osaka Japan http panasonic net 2006 Matsushita Electric Industrial Co Ltd All Rights Reserved N1206 0 1 3TROO4678AAA Printed in Japan
13. to register cameras in advance 4 cameras can be registered as a group and up to 2 groups 8 cameras can be registered page 26 Important e Select OFF for both the user authentication and the host authentication of the camera to be registered pages 34 and 35 e Only JPEG images can be displayed on a multi screen Audio will not be heard e When the power is turned off or the LAN cable is disconnected while displaying images displaying images ona multi screen from the Live page will become unavailable Step 1 Click the Multi screen button Images from the registered cameras will be dis played on a 4 split screen 2006 01 01 0 00 1 To display images on a single screen click the Live button 2 Click a camera title Live images from the camera corresponding to the clicked camera title will be dis played on the Live page of the newly opened win dow Action at an Alarm Occurrence The alarm action will be performed when the following alarm occur Alarm type Terminal alarm When connecting an alarm device such as a sensor to the alarm connector on the mounting side of the camera the alarm action will be performed when the connected alarm device activated VMD alarm When a motion is detected in the set VMD area the alarm action will be performed VMD stands for Video Motion Detection Command alarm When a Panasonic alarm protocol page 27 is received from the connected device via
14. zone Select a time zone according to the location where the camera Is in use Default setting GMT Greenwich Mean Time Dublin Edinburgh Lisbon London Configure the settings relating to SD memory card SD memory card Click the SD memory card tab on the Basic setup page page 15 The settings relating to the SD memory card can be configured on this page 2006 01 01 0 00 235840KB 235904kKB remaining total E SD memory card setup About SD memory card Select Use or Not use to determine whether or not to use the SD memory card Important e Before removing the SD memory card from the cam era it is necessary to select Not use first e After inserting the SD memory card it is necessary to select Use to use the SD memory card Notification for SD memory card When the E mail notification function or the Panasonic alarm protocol function is used to provide notification of the remaining space of the SD memory card select a level to be notified at from the following 50 20 10 5 2 Default setting 50 Note Notification will be provided each time the remaining space of the SD memory card reached the values above For example notification will be provided each time the remaining space reaches 50 20 10 5 and 2 when 50 is selected Notification may not always be made at the very moment when the remaining space of the SD mem ory card has reached each value E Informat
15. 4096 kbps Default setting 2048 kbps Note The MPEG 4 bit rate is synchronized with Total bit rate on the Network tab of Network setup page page 39 For this reason the bit rate may be lower than the value when the setting value with an asterisk on the right is selected Image capture size Select QVGA or VGA for the image capture size of MPEG 4 images Default setting VGA Image quality Select image quality of MPEG 4 images from the follow ing Fine Normal Low Default setting Normal Refresh interval MPEG 4 Select an interval l frame interval 1 5 seconds to refresh the displayed MPEG 4 images If using under the network environment with frequent error occurrences shorten the refresh interval for MPEG 4 to diminish image distortions However the refresh interval MPEG 4 may be longer than the set value when displaying JPEG images Default setting 3 sec Transmission type Select a MPEG 4 transmission type from the following Unicast port AUTO Up to 8 users can access a sin gle camera concurrently Unicast port1 Image and Unicast port2 Audio will automatically be selected when transmitting images and audio from the camera When it is unnecessary to fix the port number for MPEG 4 image transmission such as when using in a particular LAN environment it is recommended to select Unicast port AUTO Unicast port MANUAL Up to 8 users can access a single camera co
16. 7 and 29 for further information about the settings relating to the alarm action at an alarm occur rence and the alarm out connector Important Depending on the network line speed or the network traffic images may not be transmitted at the exact designat ed interval or period 2006 01 01 0 00 rt A Dopo fois 1 65535 EI Network Camera Wi NEDee WV NF284 UII ata ttt To FTP setup When To FTP setup is clicked the FTP tab of the Server setup page will be displayed page 37 Alarm image FTP transmission Select ON or OFF to determine whether or not to transmit the alarm image to the FTP server Default setting OFF Directory Enter the directory name where the alarm images are to be saved For example enter ALARM to designate the directory ALARM under the FTP root directory Number of characters for the directory name 0 256 characters File name Enter the file name used for the alarm image to be transmitted to the FTP server The file name will be as follows Entered file name Time and date year month day hour minute second Serial number Number of characters for the file name 1 8 charac ters Post alarm e Transmission interval Select a transmission interval for the alarm image FTP transmission from the following 0 1 fps 0 2 fps 0 33 fos 0 5 fos 1 fps Default setting 1 fps e Number of images Select the number of images to be transmitted from the fo
17. DDNS Category Content Connection error Cannot connect to DDNS server User name and password isn t correct IP address updated failed Internal error Other error Error indications relating to NTP Category Content Connection error Cannot connect to NTP server Internal error Other error Time adjustment syn Succeeded in the update chronizing with NTP suc ceeded Description e The designated IP address of the DDNS may be incorrect Check if the DDNS set tings are configured correctly e The DDNS server may be down Ask the network administrator Entered user name or password may be incorrect Check if the DDNS settings are configured correctly IP address update error occurred in the DDNS server Ask the network administrator An error occurred in the DDNS function Check if the DDNS settings are configured correctly Description e The IP address of the server may be incorrect Check if the IP address of the server is configured correctly e The NTP server may be down Ask the network administrator e The designated IP address of the NTP server may be incorrect Check if the DNS settings are configured correctly e The DNS server may be down Ask the network administrator Time correction succeeded Troubleshooting Before asking for repairs check the symptoms with the following table Contact your dealer if a problem cannot be solved even after checking and trying the solution or if the problem is no
18. Depending on the traffic of the network or the concen tration of access to the camera there might be diffi culties displaying the camera picture Click the reload button of the browser to request the camera picture to be refreshed Images are displayed blurry Images cannot be saved on the SD memory card Unnecessary title bar is dis played when displaying images on a full screen No image is displayed ona full screen gt gt gt gt Cause solution e Aren t there dusts or dirt on the dome cover Check if there are dust or dirt on the dome cover e Is the focus adjusted correctly Check if the focus is adjusted correctly e Is the SD memory card inserted correctly Check if the SD memory card is inserted correctly e Is the SD memory card formatted Format the SD memory card e Isn t the write protect switch set to LOCK When the write protect switch is set to LOCK avail able size total size indication of the SD memory card will be WER RRRESERA BLS e SARE ESSE lt B e Isn t the SD memory card out of order There are limited times to overwrite on an SD memory card When frequently overwritten it may be at the end of product life It is recommended to replace the SD memory card e Open the Security tab of Internet options under Tools on the menu bar of Internet Explorer Then add the IP address of the camera to Trusted sites e Wasn t the Esc key pressed bef
19. PEG images and the FTP periodic transmission simultaneously 39 40 Notes e The port forwarding function changes a global IP address to a private IP address and Static IP masquerade and Network Address Translation NAT have this function This function is to be set in a router e To access the camera via the Internet by connecting the camera to a broadband router it is necessary to assign a respective port number for each camera and address translation by using the port forwarding function For fur ther information refer to the operating instructions of the broadband router in use Enter Global IP address colon port number in the Address box of the browser WAN via the Internet Global address VW XXX YVY ZZZ 82 A VY y Z ZZ VVV XXX YVY ZZZ 8 1 Internet e S 5 o o co co So WAN Cable modem xDSL modem Broadband router an Pan Private addikss PA PM 192 168 0 254 Address translation using the port forwarding function VVV XXX YVY ZZZ 82 gt 192 168 0 2 82 Private address 192 168 0 2 Port number 82 Address translation using the port forwarding function VVV XXX YVy ZZZ 81 gt 192 168 0 1 81 Private address 192 168 0 1 Port number 81 Configure the settings relating to DDNS DDNS Click the DDNS tab on the Network setup page page 15 The settings relating to DDNS can be configured on this page When accessing the camera via the Internet from the
20. Panasonic Network Camera Network Operating Instructions Model No WV N F284 Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use No model number suffix is shown in this manual CONTENTS Fe TAC ee abel viv arauesescerearenctnnssracusidentonestansue E E E EE 3 About these operating instructions cceccccecseeeeeeceeeeeeeeeeeeseeesaaeeeeeeseeeeeeseseeeesaaaeeees 3 Trademarks and Registered Trademarks cccccccseeeececeeeeeeeeeaeeeeeeeeeeeeeesueeeeessaaeeees 3 Viewer OM WAN G cresian Errn E rN rA Ee EE N RESETE EREN EAEri 3 Montor images on a PO ce otc ne i EEN EEE 4 Monitor images from a single camera scsuiersneredaaesvinmdsearidvscinsanivonesiesaneksndee enon 4 Monitor images from multiple cameras nnnnnnnnsennnsnnnennnenrrresrnrnsnrersrrrnsrrrsnnrrenrersnnne T PCUOM atan Alarm OCCUMENCE sersissisacrsaaoani ooer a EE E EE AREE 8 Transmit Images onto an FTP Server ccccccccceesssseecceeeeeaeeeceeeeeeeeeeeeeeeesseeeeeeeeeesaaseeeeees 9 Transmit an alarm image at an alarm occurrence Alarm image FTP transmission wes seas crncdenenessmeconecinnctisouecrnactagdenteeensmnetasenemmbunsnesnectnengic 9 Transmit images at a designated interval or period FTP periodic transmission 9 Save images on the SD memory card when failed to transmit images by the FTP periodic transmission function cccccsseeceeeeeeeeeeeeeeseee
21. able IP addresses gt e 0 eO e 255 eo e 127 0 0 1 e Class D address 224 0 0 0 239 255 255 255 E Network setup Class E address 240 0 0 0 255 255 255 255 DHCP These IP addresses are unavailable even when Select ON or OFF to determine whether or not to use using the DHCP function Refer to the network the DHCP function administrator for the settings of the DHCP server Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs Net mask whose IP address is unique Refer to the network When not using the DHCP function enter the net mask administrator for the settings of the server of the camera Default setting OFF Default setting 255 255 255 0 Default gateway When not using the DHCP function enter the default gateway of the camera Default setting 192 168 0 1 lt Unavailable IP addresses for the default gate way gt e 0 e 0 i 255 577 e 255 e 127 0 0 1 e Class D address 224 0 0 0 239 255 255 255 e Class E address 240 0 0 0 255 255 255 255 These IP addresses for the default gateway are unavailable even when using the DHCP function Refer to the network administrator for the settings of the DHCP server HTTP port Assign the port numbers independently The following port numbers are unavailable since they are already in use Available port number 1 65535 Default setting 80 lt Port numbers
22. ank File name Enter the file name name of the image file to be trans mitted and select the naming option from the following With time and date File name will be Entered file name Time and date year month day hour minute second 00 Without time and date File name will be the charac ters entered for File name only When Without time and date is selected the file will be overwritten each time a file is transmitted newly Number of characters for the file name 1 32 char acters Default setting blank Interval Select the interval for the FTP periodic transmission from the following 1 sec 2 sec 3 sec 4 sec 5 sec 6 sec 10 sec 15 sec 20 sec 30 sec 1 min 2 min 3 min 4 min 5 min 6 min 10 min 15 min 20 min 30 min 1 hour 1 5 hours 2 hours 3 hours 4 hours 6 hours 12 hours 24 hours Default setting 1 sec Image capture size Select QVGA or VGA for the image capture size of the images to be transmitted by the FTP periodic trans mission Default setting VGA 43 Configure the schedule settings of the FTP periodic transmission Click the FTP tab on the Network setup page page 15 E Schedule setup The schedule settings of the FTP periodic transmission can be configured on this page Refer to page 43 for further information about the settings relating to the FTP periodic transmission How to configure the schedule settings a http 192 168 0 10 WV NF 284 Network Camera Mi
23. ation of the remaining space of the SD memory card has been provided page 19 e When the SD memory card has become full e When mounting of the SD memory card has failed To delete the registered address click the DEL button respective to the desired address Important Confirm that the destination IP addresses are regis tered correctly When a registered IP address does not exist notification may be delayed 33 34 Configure the settings relating to the authentication Authentication setup The settings relating to the authentication such as users and PCs restrictions for accessing the camera can be con figured on this page The Authentication setup page has 2 tabs of the User tab and the Host tab Configure the settings relating to the user authentication User Click the User tab on the Authentication setup page page 15 The settings relating to the user authentication can be configured on this page Up to 16 users can be registered 2006 01 01 0 00 WV NF284 Network Camera WV NF284 OFF OON E C ee O1 Administrator 2 Camera contro 3 Live only User authentication Select ON or OFF to determine whether or not to authenticate the user Default setting OFF User name Enter a user name Number of characters for the user name 1 32 char acters Default setting blank Password Retype password Enter the password Number of characters for the
24. ble to operate the camera for around 1 minute after the initialization Initialize setup data and HTML data Click the Execute button to reset the settings of the camera and the HTML files to the default However the network settings will not be reset It is impossible to operate the camera for around 1 minute after the initial ization Restart Click the Execute button to restart the camera The camera will be inoperable for around 1 minute after the restart just as when the power is turned on Notes e To initialize the network settings turn off the power of the camera first Then turn on the power of the camera while holding down the INITIAL SET button of the camera Wait around 5 seconds without releasing the INITIAL SET button Wait around 30 seconds after releasing the button The camera will restart and the settings including the network set tings will be initialized When the notification function is on notification will be provided to the registered addresses mail address or IP address when the SD memory card has failed to mount after the restart or when the inserted SD memory card is locked pages 32 and 33 About the Displayed System Log Error indications relating to SMTP Category POPS server error SMTP server error Internal error Content Authentication error Cannot connect to POP3 SMTP server SMTP authentication error Failed to resolve mail server address from DNS Cannot c
25. crosoft Internet Explorer File Edit View Favorites Tools Help Network Camera WV NF284 Click the SET button after completing the settings Setup menu SHIEH cele gt The result will be displayed at the bottom of the win MmMon OTue Owed CO Thu Ofri Osat O Basic setu Schedule O24 hours 06 v 00 x 12 30 v dow a Camera setup Omon M Tue Owed OThu OFr Osat O H JU Of be OL M24 hours Mult screen setup Alarm setup Authentication setup oo 00 OC 00 Omon OTue Owed OThu Ofri Osat O Sun O24 hours 00 00 v 00 i o0 v a http 192 168 0 10 WV NF 284 Network Camera Microsoft Internet Explorer File Edit View Favorites Tools Help WV NF284 2006 01 01 0 00 Network Camera WV NF284 Image capture size AA Server setup Maintenance Setup menu Help Basic setup Camera setup Mult screen setup Alarm setup Authentication setup Server setup Check the check box of the desired day of the week The selected day of the week will be validated for the schedule To designate time click and select the desired hour and minute When not designating time check the checkbox of 24 hours wed OThu Ofri OSat e vi 00 12 30 v 24 hours 024 hours 00 v 00 00 i o0 v vJTue Owed OThu Ofri Osat O 00 a 00 00 a 00 OTue Owed O Thu OFr Osat O How to d
26. cting the IP address to be deleted 35 36 Configure the settings of the servers Server setup The settings relating to the mail server and the FTP server can be configured on this page The Server setup page has 2 tabs of the Mail tab and the FTP tab Configure the settings relating to the mail server Mail Click the Mail tab on the Server setup page page 15 The settings relating to the mail server used to send the alarm mail can be configured on this page WV NF284 2006 01 01 0 00 Network Camera WV NF284 OPOP before SMTP OSMTP SMTP server address Enter the IP address or the host name of the SMTP server used to send e mails Number of characters for the SMTP server address 1 128 characters POP server address When POP before SMTP is selected for Authentica tion enter the IP address or the host name of the POP server Number of characters for the POP server address 1 128 characters Important When entering the host name for NTP server address it is necessary to configure the DNS set tings on the Network tab of the Network setup page page 39 Authentication Select the authentication method to send e mails from the following None It is not necessary to clear any authentication to send e mails POP before SMTP It is necessary to clear the POP server authentication first to use the SMTP server to send e mails SMTP It is necessary to clear the SMTP serv
27. d on this page Refer to pages 28 and 29 for further infor mation about the settings relating to the alarm image and the alarm out connector Network Camera WV NF284 WV NF 284 2006 01 01 0 00 OON OFF OON OFF OON OFF 151 1 65538 Terminal alarm Select ON or OFF to determine whether or not to receive the terminal alarm Default setting OFF VMD alarm Select ON or OFF to determine whether or not to perform the alarm action using the VMD function Refer to page 30 for descriptions of how to set the VMD areas Default setting OFF Command alarm Select ON or OFF to determine whether or not to receive the command alarm The command alarm is the function that notifies of Panasonic alarm protocol from the other cameras When ON is selected alarm actions will be performed between multiple cameras Default setting OFF Originating port number Select a port number to be used to receive the com mand alarm Available value 1 65535 Default setting 8181 2 28 Configure the settings relating to the alarm image Click the Alarm tab on the Alarm setup page page 15 E Alarm image setup The settings relating to the alarm image to be transmitted to the FTP server can be configured on this page The alarm image will be transmitted to the FTP server To transmit alarm images to the FTP server it is necessary to configure the settings in advance page 37 Refer to pages 2
28. e sent with the alarm mail as an attached file The settings for alarm mail can be configured in the E mail notification setup section of the Notification tab of the Alarm setup page page 32 and the Mail tab of the Server setup page page 36 Notify of alarm occurrences to the designated IP addresses Panasonic alarm protocol This function is available only when Panasonic device such as the network disk recorder is connected to the sys tem When ON is selected for Panasonic alarm protocol the connected Panasonic device will be notified that the camera is in the alarm state The settings for Panasonic alarm protocol can be configured on the Notification tab of the Alarm setup page page 33 Transmit Images onto an FTP Server Images can be transmitted to an FTP server By configuring the following settings transmission of images captured at an alarm occurrence or captured at a designated interval to an FTP server will become available Important When using this function set the user name and password to restrict users who can log into the FTP server Transmit an alarm image at an alarm occurrence Alarm image FTP transmission An alarm image can be transmitted at an alarm occurrence to the FIP server To transmit alarm images to an FTP server it is necessary to configure the settings in advance The settings for the FTP server can be configured on the FTP tab of the Server setup page page 37 The a
29. eceeeeeeesaeeeeesesaaeeeeseseeeeeeeas 10 About the network security of this unit cc eecccccceseeeeeeeeeeeeeeeeeeeeeeseeseeeseaaeeeeesseeeeeeesaees 12 Equipped security functions staccsceecseectsnrc aecensanecesactosbonscetoseentact icionsesestoateesostiausedeneeeeees 12 Display the Setup Menu and Configure the Settings of the Camera using a PC 13 How to display the setup Menu tcivictsasnsdinierwensamiscuiunvanvesedinyeaswisanbastavianpeosundtotverdans 13 How to operate the setup Menu n ssssssssnsssrnesrrrrerrrrsrnrnsrrrrrnrrrsrrrsrnrrrrrrenrrenrrennnrrn ne 14 Configure the basic settings of the camera Basic setup cccceseeeeeeeeeeeeeseeeeeeeees 17 Configure the settings relating to images and audio Camera setup 00ee 21 Configure the multi screen settings Multi screen Setup cccccsseseeeeeeeeeeeeeeeeeeees 26 Configure the alarm settings Alarm setup cccccceeeceeceeeeeeeeeeeeeeeseeeeeeeeeeseeaeeeeeess 27 Configure the settings relating to the authentication Authentication setup 34 Configure the settings of the servers Server setup cccccecseseeeceesseeeeeeeeeeeeeeaees 36 Configuring the network settings Network setup cccccccesssseeeeeeeeeeeeeeeeeeeseaeeeeees 38 Maintenance of the camera Maintenance ccccssececcseeeeceeseesseeeeeeaeseeeeeeeessaeeeess 46 About the Displayed System Log cccccc
30. eck firmware upgrade and initialization of the setup menu can be performed on this page The Maintenance page has 3 tabs of the System log tab the Upgrade tab and the Initialization tab Check the system log System log Click the System log tab of the Maintenance page page 15 Up to 4 000 system logs can be saved on the SD memory card when the SD memory card is inserted after selecting Use for About the SD memory card on the SD memory card tab 1 page 19 When Not use is selected for About the SD memory card up to 100 system logs can be saved on the built in memory of the camera When the saved system logs have reached the maximum number the newer logs will overwrite the older system logs In this case the oldest log is the first to be overwritten The system logs will be displayed in 100 logs each When using the SD memory card the logs will be saved even when the power of the camera is turned off When not using the SD memory card the logs will be deleted when the power of the camera is turned off 2006 01 01 0 00 Time amp date Time and date at the error occurrence will be displayed Error message The descriptions about the error will be displayed Refer to page 49 for further information about the sys tem logs Upgrade the firmware Upgrade Click the Upgrade tab of the Maintenance page page 15 The current firmware can be checked and upgraded to the latest version on this
31. elete the set schedule a http 192 168 0 10 WV NF284 Network Camera Microsoft Internet Explorer File Edit View Favorites Tools Help Network Camera WV NF284 WV NF284 Image captu VGA os SET Live Setup menu setup Mon OTue Owed O Thu OFri OSat 24hours 06 voo w 12 v30 Basic setup Camera setup Mon CJ Tue Owed CJ Thu OFri OSat Mutti screen setup ae 24 hours 00 sM oo oo A oo Omon OTue Owed Thu Ofri Osat O 124 hours oo joo x o v oo v Alarm setup Authentication setup Server setup 0 00 6 00 24 00 Maintenance Help Uncheck the check box of the set day of the week Click the SET button after completing the settings The result will be displayed at the bottom of the win dow a http 192 168 0 10 WV NF 284 Network Camera Microsoft Internet Explorer File Edit View Favorites Tools Help Network Camera WV NF284 WV NF284 2006 01 01 0 00 Live Setup menu Schedule setup Omon OTue Owed Thu Ofri Osat O Basic setup _ 5 3 C24 hours 06 00 m 12 v 30 Camera setup Mon OTue Owed CO Thu Ofri Osat Multi screen setup 24 hours 00 goo a o0 voo Mon OTue Owed OThu Ofri Osat O Alarm setup 24hours 00 o0 o0 o0 v Authentication setup Server setup 0 00 6 00 24 00 Maintenance Help 46 Maintenance of the camera Maintenance System log ch
32. er File Edit View Favorites Tools Help Network Camera al 4 WV_NF284 WV NF284 a o amp 2006101101 0 00 Live Setup Multi screen uA HA 8 HA Image type JPEG a il eee 4 all E 5 a Step 3 Click the OK button after entering the user name and the password Connect to 192 168 0 10 fc d vil A R security dir User name Password Remember my password Click this button to display the setup menu Refer to the next page for further information about this menu E http 192 168 0 10 WV NF284 Network Camera Microsoft Internet Explorer File Edit View Favorites Tools Help ERT WV NF284 2006 01 01 0 00 Live Setup asic SD memory card WWV NF 284 setup ir O 12 hours 24 hours aiian naui MM DDIYYYY x Multi screen setup OON OFF Alarm setup ink Access LED ON OOFF Authentication setup ED Server setup Network setup Maintenance Help 13 14 How to operate the setup menu E http 192 168 0 10 WV NF284 Network Camera Microsoft Internet Explorer File Edit Yiew Favorites Tools Help Network Camera WV NF284 WV NF 284 2006 01 01 0 00 Live Setup SD memory card Jww NF 284 EATE 2005 io vlon 00 v co ilo 12 hours 24 hours U MM DDIYYYY OON OFF Camera setup Multi screen setup Alarm setup Authentication setup Server setup Network setup Maintenance Help Menu button Setup page 1 o Click the desired bu
33. er authen tication to send e mails Default setting None Note When you don t know the authentication method to send e mails refer to the network administrator User name Enter the user name to access the server Number of characters for the user name 1 32 char acters Password Enter the password to access the server Number of characters for the password 0 32 char acters Sender mail address Enter the mail address of a sender Entered mail address will be displayed in the From sender line of the sent mails Number of characters for the sender s mail address 3 128 characters Configure the settings relating to the FTP server FTP Click the FTP tab on the Server setup page page 15 The settings relating to the FTP server used to transmit the alarm images can be configured on this page WV NF 284 Network Camera WV NF284 Live Setup FTP server address Enter the IP address or the host name of the FTP serv er Number of characters for the FTP server address 1 128 characters Note When entering localhost for FTP server address alarm images will be sent to the SD memory card In this case images will not be sent to the FTP server periodically Important When entering the host name for FTP server address it is necessary to configure the DNS set tings on the Network tab of the Network setup page page 39 User name Enter the user name login na
34. ernet Explorer File Edit View Favorites Tools Help Network Camera WV NF284 Live Setup Setup menu Basic setup Camera setup Mult screen setup Authentication setup Server setup Network setup Maintenance Help 2006 01 01 0 00 1 White J 2 Blue 3 Green 4 Red ON OOFF ON OOFF ON OOFF CON OFF Middle v Click the Delete button respective to the area to be deleted The outline of the area will disappear Click the SET button The deletion will be completed Important The deletion will not be completed unless the SET button is clicked 31 32 Configure the settings relating to the mail notification Notification Click the Notification tab on the Alarm setup page page 15 E E mail notification setup The settings relating to the alarm mail can be configured on this page To notify of an alarm occurrence by e mail it is necessary to configure the settings of the mail server page 36 WV NF 284 Network Camera WV NF284 E mail notification Select ON or OFF to determine whether or not to notify of an alarm occurrence by e mail at an alarm occurrence Default setting OFF Attach image Select ON or OFF to determine whether or not to attach an image to the mail to be sent Default setting OFF Note The settings for Image capture size of the Alarm image setup section on the Alarm tab page 28
35. etwork Camera File Edit View Favorites Tools Help WV NF284 Microsoft Internet Explorer Network Camera 5 VENEZA 2006101101 0 00 Live Setup Setup menu Basic setup Camera setup Multi screen setup Authentication setup Server setup 1 White E 2 Blue ue 3 Green ON OOFF ON OFF ON OFF ON S OFF Heip Jetection sensitivity Middle v SET 4 Red Network setup Maintenance Select ON or OFF for Status of each VMD area When the SET button is clicked after selecting OFF the outline will become the broken line and no alarm action will be performed even when a motion is detected in the area a http 192 168 0 10 WV NF 284 Network Camera File Edit View Favorites Tools Help WV NF284 Microsoft Internet Explorer 2006 01 01 0 00 Network Camera WV NF284 Live Setup Setup menu Basic setup Camera setup Mult screen setup Authentication setup Server setup 1 White 2 B 4 Red lue 3 Green ele as SET Network setup Maintenance Select the detection sensitivity from the following The selected detection sensitivity will be applied to all the VMD areas High Middle Low Default setting Middle fA l Click the SET button after completing the settings Important The setting will not be applied unless the SET but ton is clicked Delete the set VMD area a http 192 168 0 10 WV NF 284 Network Camera Microsoft Int
36. ght when accessing to a network e SD memory card error indicator This indicator will light when it is impossible to write data on the SD memory card Configure the settings relating to the NTP server NTP Click the NTP tab on the Basic setup page page 15 The settings relating to the NTP server such as the NTP server address port number etc can be configured on this page O Synchronization with NTP server 1 65535 SET Time adjustment Select the time adjustment method from the following Manual setup Time set on the Basic tab on the Basic setup page will be used as the standard time of the camera Synchronization with NTP server Time automatically adjusted by synchronizing with NTP server will be used as the standard time of the camera Default setting Manual setup NTP server address Enter the IP address or the host name of the NTP serv er Number of characters for the NTP server address 1 128 characters Default setting blank Important When entering the host name for NTP server address it is necessary to configure the DNS set tings on the Network tab of the Network setup page page 39 NTP port Enter a port number to be used for the NTP server Available port number 1 65535 Default setting 123 Synchronization interval Select an interval 1 24 hours in 1 hour intervals of synchronization with the NTP server Default setting 1 hour Time
37. he Alarm setup page page 15 E Panasonic alarm protocol setup The settings relating to Panasonic alarm protocol can be configured on this page Network Camera WV NF284 WV NF 284 Live Setup Alarm Dia e i i 0o 4 Panasonic alarm protocol Select ON or OFF to determine whether or not to notify of an alarm occurrence by Panasonic alarm proto col when an alarm is detected Default setting OFF Note When ON is selected the alarm occurrence will be notified to the registered destination IP addresses in order to IP address 1 first to IP address 8 last Destination port Select a destination port of the Panasonic alarm proto col from the following Available value 1 65535 Default setting 1818 Retry times Select a retry time of Panasonic alarm protocol Available value 1 30 Default setting 2 E Panasonic alarm protocol Destination IP address Enter the destination IP address of the Panasonic alarm protocol from the following Host name is unavailable for the IP address Up to 8 destination addresses can be registered To notify by Panasonic alarm protocol when an alarm occurred check the Alarm checkbox respective to the desired address To provide notification using Panasonic alarm protocol when any of the following has occurred check the Diag checkbox respective to the desired address e When notific
38. he firmware using a PC in the same sub net as of the camera s e Follow the instruction of the dealer when upgrading the firmware e Use the designated file extension img for the firmware upgrade e The name of the firmware to be used for upgrade should be nf284_xxxxx img Xxxxx indicates the version of the firmware e Do not turn the power of the camera off in the process of upgrade e Do not operate the web browser including adjusting the window size in the process of upgrade e The following network settings will not be initialized when upgrade the firmware after selecting Reset to the default setting after completing the upgrade Except the network settings ON OFF for DHCP IP address net mask default gateway HTTP port line speed total bit rate time amp date 4 48 Initialize restart the camera Initialization Click the Initialization tab of the Maintenance page page 15 Initialization of the setup data and HTML files of the camera and restarting of the camera can be performed on this page WV NF 284 Network Camera WV NF284 ve ping System log Initialize setup data Click the Execute button to reset the settings to the default However the network settings will not be reset It is impossible to operate the camera for around 1 minute after the initialization Initialize HTML data Click the Execute button to reset the HTML files to the default It is impossi
39. he host Default setting OFF Important Before configuring the host authentication it is nec essary to register IP addresses of the PCs to be allowed to access the camera and determine their access levels If ON is selected for Host authenti cation before registering the hosts IP addresses it will be impossible to access the camera IP address Enter the IP address of the PC to be allowed to access the camera Host name is unavailable for the IP address Notes e When IP address subnet mask is entered it is pos sible to restrict PCs in each subnet For example when 192 168 0 1 24 is entered and 2 Camera control is selected for the access level the PCs whose IP address is between 192 168 0 0 192 168 0 255 can access the camera with the access level 2 Camera control e When the IP address already in use is entered and the REG button is clicked the respective host infor mation will be overwritten Access level Select the access level of the host from the following 1 Administrator 2 Camera control 3 Live only Refer to page 34 for further information about the access level Default setting 3 Live only Note By clicking of Host check the registered host can be selected and the selected host s IP address can be checked The registered IP address will be displayed with the access level Example 192 168 0 21 1 To delete the registered host click the DEL button after sele
40. ing the SNMP function contact the network administrator WV NF284 Network Camera WV NF284 Community name Enter the community name to be monitored Number of characters for the community name 0 32 characters Default setting blank Important When using the SNMP function it is necessary to enter the community name When no community name is entered the SNMP function will not work Camera title Enter a camera title to be used to manage the camera with the SNMP function Number of characters for the camera title 0 32 characters Default setting blank Camera location Enter the name of the location where the camera is installed Number of characters for the camera location 0 32 characters Default setting blank Contact Destination address or phone number of manager Enter the mail address or the phone number of the SNMP manager Number of characters for the destination address or the phone number of manager 0 255 characters Default setting blank Configure the settings relating to the FTP periodic transmission FTP Click the FTP tab on the Network setup page page 15 E FTP periodic transmission The settings relating to the periodic transmission of images to an FTP server can be configured on this page To transmit images to an FTP server periodically it is necessary to configure the settings of the FTP server in advance page 37 Refer to page 44 for descripti
41. ing the camera under fluorescent lamps and flickers appear select ON Default setting ON Note When using the camera under low light intensity the flicker less function may not work effectively even when ON is selected In this case select an inter val for Refresh interval JPEG s page 21 from the following 0 1 fos 0 2 fps 0 5 ftp 1 fos 2 fos 5 fos 10 fos Sensitivity up Select the sensitivity from the following OFF Does not use the sensitivity adjustment x2 Adjusts the sensitivity up to x2 automatically x4 Adjusts the sensitivity up to x4 automatically x8 Adjusts the sensitivity up to x8 automatically x16 Adjusts the sensitivity up to x16 automatically Default setting OFF Important When the sensitivity is incremented the refresh interval may be longer Backlight compensation BLC Select ON or OFF to determine whether or not to compensate backlight ON Compensates backlight Suitable when the subject has backlight OFF Does not compensate backlight Suitable when the subject has light in the front Default setting OFF Configure the settings relating to audio Audio Click the Audio tab on the Camera setup page page 15 The settings relating to audio can be configured on this page WV NF 284 Network Camera WV NF284 Setup JPEGIMPEG4 Mic mode Select ON or OFF to determine whether to turn on or off audio on a PC ON Transmits audio from the came
42. ion about SD memory card SD memory card Available size and the total size of the SD memory card will be displayed Depending on the state of the SD memory card the size indications will differ as follows Indication Description KB KB No SD memory card is inserted Failed to obtain available size due to error etc meeee KB KB The SD card memory is locked etc Note When the available size reached 0 KB images will not be saved on the SD memory card When the notification function Is on a notification mail will be sent to the registered addresses when the SD mem ory card becomes full pages 32 and 33 Format To format the SD memory card click the Execute but ton Important e Before formatting the SD memory card it is neces sary to select Use for SD memory card on the SD memory card tab of the Basic setup page page 19 and OFF for FTP periodic transmis sion on the FTP tab of the Network setup page page 43 e Format the SD memory card only by clicking the Execute button on the setup menu Otherwise the following functions using the SD memory card may not work properly with this camera e Save obtain images when failed to transmit to the FTP server using the FTP periodic transmis sion function e Save obtain the system logs e It is impossible to access the SD memory card in the process of formatting e All data saved on the SD memory card will be
43. ject access traffic etc Important e When displaying multiple MPEG 4 images on a PC images may not be displayed depending on the per formance of the PC e When ON is selected for VMD alarm s page 27 the frame rate of MPEG 4 images will become 15 fps at a maximum About the Live page Alarm occurrence indication button Camera name a http 192 168 0 10 W NF 284 Network Camera Microsoft Internet Explorer Refer to this page for further information about the Live page 1 Full screen button 2 One shot button 553 d3 Audio button File Edit Yiew Favorites Tools Help aaia m m Setup button WV_NF284 WV NF284 0 a aN 2006 01 01 0 00 4 Time and date 2 Live button Live Setup 2 i Multi screen fa ao IE eee I 3 Multi screen buttons re Ee as CE gc a E E e 4 Image type buttons mage capture size 5 Image capture size buttons ZOOM buttons i Brightness 7 Brightness buttons g e3 Main area AUX buttons EES Setup button 1 Image type buttons Click this button to display the setup menu The but ton will turn green and the setup menu will be dis played C Live button Click this button to display the Live page The but ton will turn green and the Live page will be dis played OE Multi screen buttons Images from multiple cameras can be displayed on a multi screen by registering cameras on the setup menu amp page 7
44. larm image FTP transmission function can be turned on off on the Alarm tab of the Alarm setup page page 28 Note Depending on the network traffic number of the transmitted images may not reach the set number of images to be transmitted Transmit images at a designated interval or period FTP periodic transmission Images can be transmitted at a designated interval or period To transmit images at a designate interval or period it is necessary to configure the settings in advance The settings for the FTP server to which images are to be transmitted can be configured on the FTP tab of the Server setup page page 37 On the FTP tab of the Network setup page the FTP periodic transmission function can be turned on off and the settings relating to schedules periods can be configured page 43 45 Notes e Depending on the network line speed or the network traffic images may not be transmitted at the exact designat ed interval or period e When ON is selected for both of the alarm image FTP transmission function and the FTP periodic transmission function the alarm image FTP transmission function will be given priority over the FTP periodic transmission function For this reason images may not be transmitted at the exact designated interval or period if alarms occur frequently 10 Save images on the SD memory card when failed to transmit images by the FTP periodic transmission function Images that have
45. llowing 10 pics 20 pics 30 pics 50 pics 100 pics 200 pics 300 pics 500 pics 1000 pics 2000 pics 3000 pics 5000 pics Default setting 100 pics e Recording duration Approximate time to be taken to save the set num ber of images with the set transmission interval will be displayed Image capture size Select QVGA or VGA for the image capture size of images to be transmitted to the FTP server or of an image to be attached to the alarm mail Default setting VGA Configure the settings relating to the alarm out connector Click the Alarm tab on the Alarm setup page page 15 E Alarm output terminal setup The settings relating to the alarm out connector can be configured on this page Refer to pages 27 and 28 for further information about the settings relating to the alarm action at an alarm occurrence and the alarm image Network Camera WV NF284 WV NF 284 CUNT diaii 2006 01 01 0 00 SET Live Setup Alarm output setup Select ON or OFF to determine whether or not to output the alarm signals to the alarm out connector when an alarm is detected Default setting OFF External terminal output setup Select Latch or Pulse for the alarm out connector at an alarm occurrence Latch When an alarm is detected alarm output con nector will be in the state selected for Alarm output until the Alarm reset button is clicked Pulse When an alarm is detected alarm output con nector will be in
46. me to access the FTP server Number of characters for the user name 1 32 char acters Password Enter the password to access the FTP server Number of characters for the password 0 32 char acters Control port Enter a control port number to be used for the FTP serv er Available port number 1 65535 Default setting 21 FTP mode Select Passive or Active for the FTP mode Normally select Passive When failed to establish the connection select Active Default setting Passive 3 7 38 Configuring the network settings Network setup The network settings and the settings relating to DDNS Dynamic DNS and SNMP Simple Network management Protocol can be configured on this page The Network setup page has 4 tabs of the Network tab the DDNS tab the SNMP tab and the FTP tab Configure the network settings Network Click the Network tab on the Network setup page page 15 The following information is required to configure the network settings Contact the network administrator or your Internet service provider e IP address e Net mask e Default gateway when using the gateway server router e HTTP port Number e Primary DNS Secondary DNS when using DNS IP address When not using the DHCP function enter the IP address of the camera Do not enter the IP address already in use for the PCs and the other network cam eras Default setting 192 168 0 10 lt Unavail
47. ncurrently It is necessary to select Unicast port Image and Unicast port2 Audio manually to transmit images and audio from the camera It is possible to fix the port number of the router used for MPEG 4 image transmission via the Internet by setting Unicast port MANUAL Refer to the oper ating instructions of the router in use Multicast No concurrent access limitation for a cam era Refer to page 4 for further information about the maximum concurrent access number Default setting Unicast port AUTO Unicast port1 Image Enter the unicast port number used to transmit image from the camera Available value 1024 50000 Only even numbers are available Default setting 32004 Unicast port2 Audio Enter the unicast port number used to transmit audio from the camera Available value 1024 50000 Only even numbers are available Default setting 33004 Multicast address Enter the multicast IP address Images and audio will be transmitted to the designated IP address Available value 224 0 0 0 239 255 255 255 Default setting 239 192 0 20 Multicast port Enter the multicast port number used to transmit MPEG 4 images from the camera Available value 1024 50000 Only even numbers are available Default setting 37004 Multicast TTL Enter the multicast TTL value Available value 1 254 Default setting 16 Important e Depending on the PC in use for monitoring
48. network environment of which the global IP address is obtained using DHCP the DDNS function is necessary When using the DDNS function it is possible to access with Host name registered in the DDNS server nmdns net To use the DDNS function it is necessary to connect to the dedicated DDNS server Refer to the web site for further information about the DDNS Refer to the Readme file about the web site It is necessary to configure the host name user name and password registered in the DDNS server DDNS Select ON or OFF to determine whether or not to use the DDNS function Default setting OFF Host name Enter the host name to be used Number of characters for the host name 1 64 char acters User name Enter the user name login name to access the DDNS server Number of characters for the user name 1 32 char acters Password Enter the password to access the DDNS server Number of characters for the password 0 32 char acters Access interval Select the interval to access the DDNS server to check the IP address and the host name from the following 1 min 10 min 30 min 1 hour 6 hours 24 hours Default setting 1 hour 41 42 Configure the settings relating to SNMP SNMP Click the SNMP tab on the Network setup page page 15 The settings relating to SNMP can be configured on this page It is possible to check the status of the camera by connecting to the SNMP manager When us
49. ng the camera without changing the default password the pop up window saying that it is recommended to change the password will be dis played To enhance the security change the password for the user admin It is recommended to change this password periodically Maximum concurrent access to the camera will be limited to up to 8 users in the following case e When Unicast port AUTO is selected for Transmission type amp page 22 e When Unicast port MANUAL is selected for Transmission type amp page 22 e When JPEG images are being transmitted from the camera Depending on the set values for Total bit rate and Max bit rate per 1 client the maximum concurrent access number may be less than 8 users When 8 users have been concurrently accessing already the access limit message will be displayed for users who accessed subsequently When ON is selected for MPEG 4 transmission page 22 an MPEG 4 image will be displayed When OFF is selected a JPEG image will be dis played It is possible to display JPEG image even when ON is selected for MPEG 4 transmission In this case the refresh interval will be limited lt Refresh interval JPEG gt e When ON is selected for MPEG 4 transmission JPEG VGA 5 fps JPEG QVGA 10 fps e When OFF is selected for MPEG 4 transmission JPEG VGA or QVGA 30 fps The refresh interval may be longer depending on a net work environment PC spec photographic sub
50. nhance the security it is recommended to change the password for the administrator periodically Step 3 Move the current directory to drive B and obtain images Notes e When logging in the camera the current directory will be drive D Images on the SD memory card can be found in the FTP directory under drive B Move to the FTP directory and obtain images lt Directory structure of drive B gt Example To obtain the image img_06010101230000 jpg using the Windows command prompt Enter c gt ftp 192 168 0 10 and press the Enter key FTP connection will be established with 192 168 0 10 2 Log in by entering the user name and the password 3 Enter fto gt cd B FTP 060101 0123 and press the Enter key The current directory will be B FTP 060101 0123 Directory Directory Directory year month day hour minute 060101 An image failed to transmit by the FTP periodic transmission function 060102 Example img_06010101230000 jpg T The image will be saved here lt Destination of logs to be saved 4 The transfer mode will be set to the binary mode Enter fto gt bin and press the Enter key 5 Enter fto gt get img_06010101230000 jpg and press the Enter key The image will be obtained Log out by entering ftp gt bye and press the Enter key e It is possible to delete images on the SD memory card using the Windows command prompt etc 11 12 About the network secu
51. ollowing cameras are available for the multi screen display WV NF284 WV NS202 WV NP240 series WV NP1000 series WV NW470S series WV NP472 WV NS320 series Network Camera y WV NF284 WV NF284 2006101101 0 00 IP address Camera title a a a a SET IP address Camera title a IP address Enter the IP address or the host name of the camera to be used for the multi screen 4 cameras can be regis tered as a group and up to 2 groups 8 cameras can be registered When the HTTP port number for the camera had been changed enter as follows Example 192 168 0 10 8080 Number of characters for the IP address 1 128 characters Note When using the host name it is necessary to config ure the DNS settings of the PC in use page 39 Camera title The entered camera title will be displayed on a multi screen Number of characters for the camera title 0 20 characters Configure the alarm settings Alarm setup The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence the alarm occurrence notification and the VMD area settings can be configured on this page The Alarm setup page has 3 tabs of the Alarm tab the VMD area tab and the Notification tab Configure the settings relating to the alarm action Alarm Click the Alarm tab on the Alarm setup page page 15 E Alarm setup The settings relating to the alarm action can be configure
52. onnect to SMTP server Other error Error indications relating to FTP Category FTP server error Connection error Internal error Content Connection error to DNS server Cannot connect to FTP server File transfer error Passive mode error Log out failed Directory change failed User name and password isn t correct Other error Description Entered user name or password may be incorrect Check if the mail settings are con figured correctly e The IP address of the server may be incorrect Check if the IP address of the server is configured correctly e The POP3 server may be down Ask the network administrator Entered user name or password may be incorrect Check if the mail settings are con figured correctly e The designated IP address of the DNS server may be incorrect Check if the DNS settings are configured correctly e The DNS server may be down Ask the network administrator e The IP address of the server may be incorrect Check if the IP address of the server is configured correctly e The SMTP server may be down Ask the network administrator An error occurred in the mail function Check if the mail settings are configured correctly Description The FTP server or DNS server may be down e The FTP server settings may be incor rect e The settings relating to the indicated item may be incorrect The FTP server settings may be incorrect 49 o0 Error indications relating to
53. ons of how to configure schedules of image transmission Important e Depending on the network line speed or the network traffic images may not be transmitted at the exact designat ed interval or period e When ON is selected for both of the alarm image FTP transmission function and the FTP periodic transmission function the alarm image FTP transmission function will be given priority over the FTP periodic transmission function For this reason images may not be transmitted at the exact designated interval or period if alarms occur frequently Note Images failed to transmit by the FTP periodic transmission can be saved automatically on the SD memory card page 10 Network Camera WV NF284 WV NF284 2006 01 01 0 00 A Omon OTue Owed CO Thu Ofri Osat O Sun rs 00 o0 v o0 v o0 v u OFri O Sat O Sun y 00 x o0 v ed OThu Ofri Osat O Sun oo vioo v FTP periodic transmission Select ON or OFF to determine whether or not to transmit images using the FTP periodic transmission function When ON is selected it is necessary to configure the settings of the FTP server page 37 Default setting OFF Directory Enter the directory name where the images are to be saved For example enter img to designate the directory img under the FTP root directory Number of characters for the directory name 0 256 characters Default setting bl
54. ore images are dis played Close the browser window by pressing the Alt key and F4 key simultaneously etc Reference pages Installation Guide Installation Guide O 93 54 When displaying MPEG 4 images on two browser win dows or more images from two cameras or more are displayed in sequence on a single browser window Reference Cause solution pages e This may occur due to the display adapter and driver combination When this occurred update the driver of the display adapter to the latest version first If updating the driver does not solve the problem adjust the hardware acceleration as follows The following are descriptions for when Microsoft XP Professional SP2 is installed on the PC in use 1 Right click on the desktop and select Properties from the displayed pop up menu 2 Select Settings from Display Properties and then click the Advanced button 3 Click the Troubleshoot tab and disable the DirectDraw acceleration by adjusting the level of Hardware acceleration Color Management a General Adapter Monitor Troubleshoot O Are you having problems with your graphics hardware These settings can help you troubleshoot display related problems Hardware acceleration Manually control the level of acceleration and performance supplied by your graphics hardware Use the Display Troubleshooper to assist you in making the change Hardware acceleration None
55. ovided CD ROM e The viewer software used on each PC should be licensed individually Refer to your dealer for the software licensing Monitor Images on a PC The following are descriptions of how to monitor images from the camera on a PC Monitor images from a single camera Step 1 Start up the web browser Step 2 Enter the IP address designated using the Panasonic IP setup software in the address box of the browser Example http 192 168 0 10 a sonic com Hash ntm Panasonic ideas for life Now all Panasonic digital cameras have so your memories will never be shaky again more more gt ss more gt moe nasonic Digital Concepts Center Oxyride p Panasonic Avionics Corporation more gt sis perfect one for your home more more Important e When the HTTP port number is changed from 80 enter http IP address of the camera colon port number in the address box of the browser for example http 192 168 0 11 8080 e Configure the web browser to not use the proxy server Step 3 Press the Enter key on the keyboard The Live page will be displayed WV NF284 oao D 2006101101 0 00 Notes e When ON is selected for User Authentication page 34 the authentication window will be dis played before displaying live images for the user name and password entries The default user name and password are as follows User name admin Password 12345 When accessi
56. owser 91 92 Cannot access from the browser No image is displayed The image is not being refreshed Reference Cause solution pages e Is the same IP address provided to other devices Are there contradictions between the address and the network subnet to be accessed lt When the camera and the PC are connected in the same subnet gt Are the IP addresses of the camera and the PC set in a common subnet Or is Use Proxy Server for the settings of the browser checked When accessing the camera in the same subnet it is recommended to enter the address of the camera in the Don t Use Proxy For These Addresses box lt When the camera and the PC are connected in the different subnet gt Is the IP address of the default gateway set for the camera correct Is the power of the camera on Installation Check if the power of the camera is turned on Guide Is the viewer software installed on a PC Installation Install the viewer software on a PC Guide Is the version of DirectX 9 0c or later Check the version of DirectX as follows 1 Select Run from the start menu of Windows 2 Enter dxdiag in the displayed dialog box and click the OK button If the version of DirectX is older than 9 0c upgrade it Depending on the version of your browser there might be difficulties refreshing the picture and operat Installation ing the camera Guide It is recommended to use Internet Explorer 6 0 SP2
57. page Contact the dealer for further information about the firmware upgrade Network Camera WV NF284 WV NF284 Reset to the default settings after completing the upgrade Except the network settings O Do not reset the settings after completing the upgrade It wil take for around 4 minutes with resetting the settings or for around 3 minutes without resetting the settings to complete the upgrade Please wait for a while Please do not operate the browser in the process of the upgrade Model No MAC address Firmware version IPL version Information of each item will be displayed How to upgrade the firmware Step 1 Contact the dealer and download the latest firmware onto a PC Important A blank space cannot be used for the name of the directory where the downloaded firmware to be saved Step 2 Click the Browse button and designate the down loaded firmware Step 3 Click the radio button respective to the desired option to determine whether or not to initialize the settings after the firmware upgrade Note Read the readme file provided with the firmware first and determine whether or not to initialize the settings after the firmware upgrade Step 4 Click the Upgrade button The confirmation window will be displayed When Do not reset the settings after completing the upgrade was selected the confirmation window will not be displayed Important e Upgrade t
58. password 4 32 char acters Default setting blank Note When the user name already in use is entered and the REG button is clicked the respective user infor mation will be overwritten Access level Select the access level of the host from the following 1 Administrator Allowed all available operations of the camera 2 Camera control Allowed to display images from the camera and to control the camera The camera set ting configuration is unavailable 3 Live only Only displaying live images is available The camera setting configuration and camera con trol are unavailable Default setting 3 Live only Note By clicking of User name check the registered user can be selected and the selected user s infor mation can be checked The registered user will be displayed with the access level Example admin 1 To delete the registered user click the DEL button after selecting the user to be deleted Important If all users whose access level is 1 Administrator is deleted it will be impossible to configure the set tings Configure the settings relating to the host authentication Host Click the Host tab on the Authentication setup page page 15 The settings to restrict PCs IP address to access the camera can be configured on this page Network Camera S WV NF284 WV NF284 2006101101 0 00 Host authentication Select ON or OFF to determine whether or not to authenticate t
59. ra to the PC Audio can be heard with images on the PC Images and audio will not be synchronized OFF Audio will not be transmitted from the camera to the PC Therefore no settings and controls relating audio will be invalidated Default setting ON Audio bit rate Select 16 kbps or 32 kbps for audio bit rate Default setting 32 kbps Audio sensitivity Select the sensitivity of the built in microphone of the camera from the following Low Middle High Default setting Middle Transmission interval Select an interval for audio transmission from the follow Ings 20 msec 40 msec 80 msec 160 msec Default setting 40 msec Note When a shorter interval is selected delay time will be shorter When a longer interval is selected audio interruption may be diminished even though delay time will be longer Select the interval according to the network environ ment Authentication Select an access level for audio transmission from the following Refer to page 34 for further information about the access level Level 1 only Level 2 or higher All users Default setting All users Note Images and audio will not be synchronized Therefore images and audio may not always match 20 26 Configure the multi screen settings Multi screen setup The cameras to be used for the multi screen display can be registered on this page Refer to page 15 for descriptions of how to display images on a multi screen The f
60. rity of this unit Equipped security functions The following security functions are featured in this camera Access restrictions by the host authentication and the user authentication It is possible to restrict users from accessing the camera by setting the host authentication and or the user authentication to on pages 34 and 35 2 Access restrictions by changing the HTTP port It is possible to prevent illegal access such as port scanning etc by changing the HTTP port number page 39 Note When failed to pass the user authentication authentication error using the same IP address PC for 8 times within 5 minutes access to the camera will be denied for a while Important Design and enhance security countermeasures to prevent leakage of information such as image data authenti cation information user name and password alarm mail information FTP server information DDNS server information etc Display the Setup Menu and Configure the Settings of the Camera using a PC The settings of the camera can be configured on the setup menu The setup menu Is only operable by users whose access level is 1 Administrator How to display the setup menu Step 1 Display the Live page page 4 Step 2 Click the Setup button on the Live page The window with the user name and password entry fields will be displayed E http 192 168 0 10 WV NF284 Network Camera Microsoft Internet Explor
61. rm output connector will be reset page 29 Ed Full screen button Images will be displayed on a full screen To return to the Live page press the Esc key or the F5 key or the combination of the Alt key and the F4 key on the keyboard 2 One shot button Click this button to take a picture a still picture The picture will be displayed on a newly opened window When right clicking on the displayed image the pop up menu will be displayed The displayed image can be saved on the PC by selecting Save from the pop up menu 43 d Audio button The Audio button will be displayed only when ON is selected for Mic mode on the setup menu page 25 When this button is clicked the button will turn into 1 button and audio will not be heard Time and date Current time will be displayed in the set date time display format page 17 5 Main area Images from the camera will be displayed in this area 1 Operable by only users whose access level is 1 Administrator 2 Only operable by users whose access level is 1 Administrator or 2 Camera control when ON is selected for User authentication page 34 Refer to page 34 for further information about the access level Monitor images from multiple cameras Images from multiple cameras can be displayed on a multi screen Images from up to 4 cameras can be displayed simultaneously To display images on a multi screen it is necessary
62. se settings currently being configured and date and time will be dis played 2 Setup page Pages of each setup menu will be displayed There are tabs for some setup menus Configure the basic settings of the camera Basic setup The basic settings such as time and date and camera name and the settings relating to the NTP server and the SD memory card can be configured on the Basic setup page The Basic setup page has 3 tabs of the Basic tab the NTP tab and the SD memory card tab Configure the basic settings Basic Click the Basic tab on the Basic setup page page 15 The settings such as the camera name time and date etc can be configured on this page 2006 01 01 0 00 v o0 fo 24 hours Camera title Enter the title of the camera Click the SET button after entering the title of the camera The entered title will be displayed in the status display area Number of characters for the camera title 0 20 characters Default setting WV NF284 Time and date setup Enter the current time and date When 12 hours is selected for Time display AM or PM can be select ed Available value 2006 01 01 00 00 00 2035 12 31 23 59 59 Note 2036 01 01 00 00 00 or later is unavailable to set and display Time display Select 12 hours or 24 hours Enter the current hour reflecting this setting when entering the current time and date for Time and da
63. seeseccceeeeeeseeeeeeeeeeeeeeeeesseeaeeeeeeeeseeaseeeeeeessageeeeees 49 fe 0 s 255 lolol ig le eee en nenen ee eee eee hee eee nner ai ee ee ee ee 51 Preface About these operating instructions There are 2 sets of operating instructions for the WV NF284 as follows e Installation Guide e Network operating instructions These network operating instructions contain descriptions of how to operate this product using a PC via a network and of how to configure the settings Refer to the installation guide for descriptions of how to install this product and of how to connect to a network Adobe Reader is required to read PDF When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it Trademarks and Registered Trademarks e Microsoft Windows Internet Explorer ActiveX and DirectX are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries e Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries e SD logo is a trademark e Other names of companies and product contained in these operating instructions may be trademarks or regis tered trademarks of their respective owners Viewer Software e Images will not be displayed when the viewer software Network camera Views is not installed on the PC Install the viewer software from the pr
64. t described below Reference Symptom Cause solution pages e Is the LAN cable category 5 is firmly connected to the network connector on the mounting side of the camera Installation Guide Are both the link indicators inside the camera and the PC right by the network connector lit When it is not lit connection to a LAN may not be established or a network may be not working correct ly Check if the cables have any contact failure or if the wiring is correct or not To check network estab lishment with the link indicator inside the dome cover set the indicator ON OFF switch inside the camera to ON Installation Guide e Are you accessing the wrong IP address Check the connection as follows With the Windows command prompt gt ping IP address of the camera When the WV NF284 replies the camera is function ing normally If not proceed either of the following e Restart the camera and change the IP address by using the Panasonic IP setup software within 20 minutes after the restart Restart the camera while holding the INITIAL SET button on the mounting side of the camera The camera will be initialized and the IP address will return to the default setting 192 168 0 10 After the camera is initialized access the camera and set the IP address again When the camera is initialized all the settings of the camera previ ously configured on the setup menus will be initial ized Cannot access from the br
65. te setup Default setting 24 hours Date time display format Select a date time display format When 04 01 2006 13 10 00 is set for Time and date setup after selecting 24 hours for Time display time and date will be displayed as follows respectively DD MM YYYY 01 04 2006 13 10 MM DD YYYY 04 01 2006 13 10 DD Mmm YYYY 01 Apr 2006 13 10 YYYY MM DD 2006 04 01 13 10 Mmm DD YYYY Apr 01 2006 13 10 Default setting MM DD YYYY Daylight saving Summertime Select ON or OFF to determine whether or not to apply daylight saving time Select ON or OFF to determine whether or not to apply daylight saving time ON Applies summer time An asterisk will be dis played on the left side of the displayed time and date OFF Does not apply summer time Default setting OFF Link Access LED Select ON or OFF to determine whether or not to light the link indicator the access indicator and the SD memory card error indicator Select ON to check the network status by lighting the indicators Select OFF to turn off the indicators at all times e Even when ON is selected the link indicator and the access indicator inside the dome cover will not light when the indicators ON OFF switch on the camera is set to OFF Default setting ON 17 18 Notes e Link indicator This indicator will light when com munication with the connected device is available e Access indicator This indicator will li
66. the mul ticast port number may be already in use In this case it may be impossible to monitor images Change the multicast port number e When transmitting MPEG 4 image via a network the transmitted image sometimes may not be displayed In this case refer to the network administrator e When two or more network interface cards are installed on the PC in use the network interface card s not used for receiving images should be invalidated when displaying images using the multi cast port 23 24 Configure the camera settings such as image quality and brightness etc Camera Click the Camera tab on the Camera setup page page 15 The following are descriptions of how to configure the settings relating to images such as brightness etc 2006 01 01 0 00 Brightness 17 steps 8 8 are available for brightness The value 8 is the darkest and 8 is the brightest Default setting 0 White balance Select the white balance adjustment method from the following AUTO Adjusts the white balance automatically HOLD Fixes to the white balance applied when the SET button is clicked Default setting AUTO Aperture level 9 steps 4 4 are available for aperture level sharp ness The value 4 is the softest and 4 is the sharpest Default setting 0 Flicker less mode Select ON or OFF to determine whether or not to use the flicker less mode Normally select OFF When us
67. the opposite state to the Alarm out put setting for the period set for Pulse width Default setting Latch Alarm output Select Open or Close to determine whether to open or close the alarm output connector when output the alarm signals Open The alarm out connector will open when output the alarm signals Normally close Close The alarm out connector will close when output the alarm signals Normally open Default setting Open Note When Open is selected the alarm signal will be output for around 20 seconds when the power of the camera is turned on Pulse width When Pulse is selected for Alarm output select an pulse width Available value 1 120 sec Default setting 1 sec 29 30 Set the VMD areas VMD area Click the VMD area tab on the Alarm setup page page 15 The video motion detection areas can be set on this page When a motion is detected in the set area the alarm action will be performed Set the VMD areas Set the video motion detection area by dragging the mouse on the screen When the All areas button is clicked the whole area will become the VMD area and 1 White will be automatically applied to Area The designated area will become the VMD area and the outline will be displayed When 2 4 VMD areas are set each area will be numbered in order The areas will be identified by the respective outline colours a http 192 168 0 10 WV NF 284 N
68. to alarm occurrences such as settings for the alarm action at an alarm occurrence the alarm occurrence notification and the VMD area settings can be configured on the Alarm setup page Refer to page 27 for further information Authentication setup button Click this button to display the Authentication setup page The settings relating to the authentication such as users and PCs restrictions for accessing the camera can be configured on the Authentication setup page Refer to page 34 for further informa tion D Server setup button Click this button to display the Server setup page The settings relating to the mail server and the FTP server to which the camera accesses can be config ured on the Server setup page Refer to page 36 for further information 15 Network setup button Click this button to display the Network setup page The network settings and the settings relating to DDNS Dynamic DNS SNMP Simple Network management Protocol and FTP File Transfer Protocol can be configured on the Network setup page Refer to page 38 for further information a Maintenance button Click this button to display the Maintenance page System log check firmware upgrade and initializa tion of the setup menu can be performed on the Maintenance page Refer to page 46 for further information E Help button Click this button to display the Help page Status display area The name of the camera who
69. tton in the frame on the left of the window to display the respective setup menu When there are tabs at the top of the setup page dis played in the frame on the right of the window click the desired tab to display and configure the setting items relating to the name of the tab Complete each setting item displayed in the frame on the right of the window After completing each setting item click the SET but ton or REG button to apply them Important When there are two SET buttons or REG but tons or more on the page click the respective but ton to the edited setting item lt Example gt 2006 01101 0 00 a Di 31 1 65535 as ET To FTP setup a When completing the setting items in field A click the SET button below field A A 1 The edited set ting items in field A will not be applied unless the SET button below field A A 1 is clicked In the same manner as above click the SET button below field B B 1 when completing the setting items in field B About the operation window E http 192 168 0 10 WV NF284 Network Camera Microso File Edit View Favorites Tools Help Network Camera WV NF284 WV NF284 1 Live button Live Setup Basic Camera title Setup menu 2 Basic setup button Time amp date setup 3 Camera setup button Camera setup Multi screen setup 4 Multi screen setup button Alarm setup 5 Alarm setup button

Network Operating Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents