Copyright Disclaimer FCC Warning
Contents
1. Blinks when any FX packets trans EX LNK Green mitting and receiving ACT Lit when Fiber connection is good Blinks when any TP packets trans TX ILNK Green mitting and receiving ACT Lit when TP connection is good Lit when Full duplex mode is en FX FDX Green abled in FX port Lit when Full duplex mode is en abled detect by Auto Negotiation in TP port Lit when the TP port runs in 100Mbps Remains off while LINK LED lit represent the TP port runs in 10Mbps 10 Lit when 5VDC power detected Note Fiber optic Partner should be set to the correct mode according to this FDX indicator for optimal network performance 0 5 E Cable Connection Parameter The limitations are as below Duplex Limitation max Twisted Pair Half Full Node te Node 100 meters Node to Switch Hub Multi Mode Converters MM Half Node to Neue 412 meters Node to Switch Node to Node X MM Full j 2 kilometers Node to Switch Single Mode Converters FT 802S Node to Node SM Full Depends on model Node to Switch Note Consult your local dealer for more about our single mode fiber connectivity J6 FT 80X Technical Specifications The FT 80X comes with the following standard features Standard IEEE802 3 u 10 100Base TX and 100Base FX Connectors gt One RJ 45 Auto MDI MDI X Twisted Pair EIA568 One Fiber optic 1300nm wavelength connector type vary with model Data Transfer Rat2. Copyright Copyright C PLANET Technology Corp 2003 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technol ogy Corp The information in this manual is subject to change without notice All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality per formance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comply with the regulations for a Cla
3. e 10 100Mbps TP 100Mbps FX Duplex mode support Full or half duplex mode by Auto Negotiation TP LED indicators PWR FX LNK ACT FX FDX TP 100 TP LNK ACT TP FDX Power Requirement 5V DC 2A Ambient Temperature 0 to 50 C operating Humidity 5 to 90 non condensing Dimension 26 x 70 x 97mm HxWxD Cable UTP Cat 5 UTP cable gt Fiber MM 50 125 mm or 62 5 125 mm optic fiber gt Fiber SM 8 3 125 8 7 125 9 125 mm optic fiber Connecting to Router Bridge or Switch Hub please refer to the device s Technical Manual 7 Power information The power jack of FT 80X is with 2 5mm in the central post and required 5VDC power input It will conform to the bundled AC DC adapter and Planet s Media Chassis Should you have the problem to make the power connection please contact your local sales representative Please keep the AC DC adapter as spare parts when your FT 80X is installed to a Media Chassis Part No 2010 000002 002 C
4. module to the 19 media chassis up to 15 units for a TP and Fiber combined networks at a central wiring closet Please contact with your sales representative for more about the 19 media chassis Model List Your Fast Ethernet Converter comes with one of the following models FT 801 on board ST fiber connector FT 802 S on board SC fiber connector Models with last character S indicate the fiber port is with Single Mode optic fiber connector In the following sections the term FT 80X indicates the product family above Checklist Your FT 80X carton should contain the following items gt The Fast Ethernet Bridge Converter gt AC DC Power Adapter Output 5VDC 2 A max gt This user s manual If any item is missing or damaged please consult the dealer from whom you purchased your Fast Ethernet Converter 1 Product Outlook Right View There are one RJ 45 Twisted Pair jack Auto MDI MDI X one fiber optic connector and six LED indicators FX TX TX RX oO Omaa O Ox O Qu Fast Ethernet Bridge EWR 10 100Base TX to 100Base FX Left View One DIP switch for Fiber optic mode operating selection FDX for full duplex and HDX for half duplex 5VDC 6 FX Duplex Hpx L FDX oeo 2 Installing the Converter Please follow these steps to install the converter Turn off the power of the device statio
5. n in a network to which the FT 80X will be attached Ensure that there is no activity in the network Attach fiber cable from the FT 80X to the fiber network TX RX must be paired at both ends Attach a Cat 5 UTP cable from the 10 100Base TX net work to the RJ 45 port on the FT 80X Connect the 5VDC power adapter to the FT 80X and verify that the Power LED lights up Turn on the power of the device station the TX Link and FX Link LEDs should light when all cables are attached 10 100Base TX Cat 5 5e TP Cable Network 100Base FX Fiber Network Note e RJ 45 STP UTP Cat 5 straight crossover cable is ac cepted e Please refer to section 8 for more about the wiring distance of your TP Optic fiber networks 36 Duplex Mode setting The TP port of FT 80X supports duplex mode detection by auto negotiation A N The following is the duplex mode parameters FT 80X Dupl Fast Ethernet Device z yR Ex Mode support Ethernet Fast Ethernet Hub Half Duplex Ethernet Fast Ethernet Switch Half Duplex without A N Fast Ethernet Devices Full Duplex Support Auto Negotiation Half Duplex Note Normally an A N switch will detect and set to full duplex where a dual speed hub will detects half There is a DIP switch as in the left view as section 4 Please check and follow the duplex mode of the fiber device and have the duplex selection to your FT 80X j4 LED indication COLOR DESCRIPTION
6. ss A digital device pur suant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communica tions Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will b CE mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Revision User s manual for PLANET Fast Ethernet Converter Multi mode FT 801 FT 802 Single mode FT 802S Rev 3 0 May 2003 Part No 2010 000002 002 Table of Contents Overview 1 Model List 1 Checklist 1 Product Outlook 2 Installing the Converter 3 Duplex Mode setting 4 LED indication 5 Cable Connection Parameter 6 FT 80X Technical Specifications 7 Power information 8 Overview Thank you for purchasing PLANET FT 80X family 10 100Mbps Ethernet Twisted pair to 100Base FX Fiber optic Bridge Converter This converter is used to convert one type media signal to other type equivalent that allows two type segments connect easily efficiently and inexpensively This converter can be used as a standalone unit or as a slide in
Download Pdf Manuals
Related Search