ADC-PMC User Manual
Contents
1. e JP2 JP4 JP6 and JP10 are reserved for future use Do not fit links in these positions e JP3 JPS and JP7 can be fitted in any combination Check the Pn4 information for the PMC s that are fitted to ensure there are no contention issues e See following section for Special Modes ADC PMC2 User Manual 3 2 Special Modes There are two modes available using JP8 and JP9 The configurations selected by these jumpers are shown in the diagrams below Figure 2 JP8 Installed Figure 3 JP8 and JP9 Installed 3 3 JP1 Additional Notes JP1 is connected to the M66EN signal of the secondary PCI bus connecting the bridge to the PMC sites It is necessary to fit this link if the ADC PMC2 is fitted to 33 MHz PCI slots and there are only 66MHz capable cards fitted to the PMC slots In all other cases the link can be removed for automatic PCI clock control 3 4 J1 PCI Connector This is a standard edge connector for PCI and is compatible with 32 bit slots with 3V or 5V signalling and 64 bit slots with 3V signalling 3 5 J2 JTAG Connector This connector provides access to the CPLD U2 and should only be used in manufacturing as changes to this device could cause system failure ADC PMC2 User Manual 3 6 J4 Header Configuration The IO header J4 is suitable for2. ADC PMC2 C1 User Manual ALPHA DATA Version 1 2 ADC PMC 2 User Manual Copyright 2002 2008 Alpha Data Parallel Systems Ltd All rights reserved This publication is protected by Copyright Law with all rights reserved No part of this publication may be reproduced in any shape or form without prior written consent from Alpha Data Parallel Systems Limited Alpha Data 4 West Silvermills Lane Edinburgh EH3 5BD UK Phone 44 0 131 558 2600 Fax 44 0 131 558 2700 Email support alphadata co uk Alpha Data 2570 North First Street Suite 440 San Jose CA 95131 USA Phone 408 467 5076 Fax 866 820 9956 Email support alpha data com ADC PMC 2 User Manual Reserved rights This manual is designed to provide outline information only Alpha Data has a continual policy of improving its products hence it reserves the right to change product specification without prior warning Alpha Data cannot accept any liability for loss or damages arising from the use of this manual or the use of products detailed within it Trademark acknowledgements MS DOS Windows95 and Windows NT are registered trademarks of Microsoft Corporation Intel is a registered trademark of Intel Corporation Warranty and Support All Alpha Data products enjoy parts and labour warranty for 12 months after purchase The warranty is based on the customer returning the defective goods to Alpha Data for repair or replac
3. ement which will be at the discretion of the company The warranty does not cover damages caused by negligence misuse and normal wear and tear No liability is accepted by the company for any damage caused by the use of its hardware or software All goods from Alpha Data carry a 6 months free support service This service is available by letter phone fax and email Technical support contracts for longer periods are available on request Support contracts for software components also normally cover the cost of upgrades ADC PMC 2 User Manual Table of Contents 1 Introduction pe om unless nr er tre eme eee Te 1 1 About the Hardware 1 2 Description Dis Installation AE Ra sess res nl dr sola wes tr ee niet enr den aS tas CREE oe 2 15 Into A PE Re 232 E AR ne M ee Se ee S 2 2 Adding PMC cards 2 3 Software Support end ne nn rene een genen seien 3 Hardware Pin out Information Sul JUPES sidi smith eurent nee te tr moines evista 3 2 SpecialLMOGRS tt interne cH ach Me enh hh eee neta eet 3 3 JP1 Additional Notes 3 4 J1 PCI Connector 3 5 J2 JTAG Connector 3 6 J4 Header Configuration ADC PMC2 User Manual 1 1 1 1 2 Introduction About the Hardware The ADC PMC2 is a 64 bit PCI carrier card for PMC modules It can be used in 3V and 5V signalling environments and in both 32 and 64 bit slots There are two PMC slots on the standard card and these can also support 32 or 64 bit operation The secondary bu
4. mating with IDC connectors and is a RN PS50E 080 P1 SR1 TG or equivalent J4 1 79 gnd gnd gnd gnd gnd hdr_io1 hdr_io3 hdr_io5 hdr_io7 hdr_io9 hdr_io11 hdr_io13 hdr_io15 hdr_io17 hdr_io19 hdr_io21 hdr_io23 hdr_io25 hdr_io27 hdr_io29 hdr_io31 hdr_io33 hdr_io35 hdr_io37 hdr_io39 hdr_io41 hdr_io43 hdr_io45 hdr_io47 hdr_io49 hdr_io51 hdr_io53 hdr_io55 hdr_io57 hdr_io59 hdr_io61 hdr_io63 gnd gnd gnd The IO header is optimised for LVDS pairing to ADM XRC II Pn4 connections All even number hdr _io signals are P with odd numbers being N For example hdr_i00 1 are a P N pair ADC PMC2 User Manual Revision History October 2007 Created from standard manual version 1 1
5. ntoaPC The ADC PMC2 is a universal PCI device meaning that it can be used in both 3V and 5V signalling environments 2 2 Adding PMC cards Fit any PMC modules that are required If only one PMC module is to be fitted either site can be used PMC site 1 is positioned so that an I O connector on the module aligns with the aperture in the ADC PMC2 s edge panel The PMC modules should be supplied with mounting kits which normally include spacers nuts bolts and washers Figure shows the typical assembly of a PMC to the ADC PMC2 It is recommended that washers be used on both sides of the ADC PMC2 to avoid damage to the PCB PMC AT a ADC PMC Figure 1 Assembly of a PMC to the ADC PMC2 2 3 Software Support The ADC PMC2 uses a PLX 6152 64 bit bridge device that is compatible with most operating systems that adhere to the PCI Bios specification No software is required to enable operation of the ADC PMC2 ADC PMC2 User Manual 3 Hardware Pin out Information 3 1 Jumpers There are 10 jumper sites on the board that are used for configuration settings bus clock select Bus er P2 1 PMC Monarch Not supported Option PMCI Pn4 mr Pn4 connected to IO isolated bus PMC2 Monarch Not supported JP5 Option PMC2 Pn4 PMC2 Pn4 connected to IO isolated bus PMC3 Monarch Not supported JP7 Option3 Header J4 Header J4 connected to IO isolated bus Special Mode 1 Special Mode 2 JP10 Not supported
6. s VIO can be configured in the factory for 5V or 3V operation The default is 3V operation The ADC PMC2 carrier card also supports features of the ADM XRC FPGA board in a PCI environment with the provision of Pn4 routing between the two PMC sites and selectively to a 64 way header Both primary and secondary bus interfaces are rated at up to 66MHz operation Description The ADC PMC2 is based on the PLX 6152 64 bit PCI PCI bridge This device supports 64 or 32 bit primary PCI and 64 or 32 bit secondary PCI Each of the two primary PMC sites supports Pn4 IO with quick switch isolation to permit various IO combinations A set of jumpers on the board enables each of the quick switch blocks The IO Bus is 64 bits wide and connects to all 64 signals from the Pn4 connector of each PMC site Further all of the IO Bus can be routed to the J4 header through a quick switch block that provides a level of protection to the IO bus signals by limiting the external signal levels Primary PCI Secondary PCI Bus Quick switch ADC PMC2 User Manual 2 Installation In order to ensure that the board operates correctly first time please read these instructions completely before attempting installation It will also help you to read the whole manual first so that you know how you want the board to be set up Figure 1 shows the physical layout of the board The installation instructions for your PC should be followed at all times 2 1 I
Download Pdf Manuals
Related Search