KM4A1 KM4CQB - Universo Sniper Airsoft
Contents
1. failure Return gun for Return gun for professional care care KM4A1 KM4CQB OPERATING UNDER UNUSUAL CONDITIONS Unusual conditions are defined as any condition requiring special maintenance Perform maintenance outlined for the climate similar to your operational area Extreme Cold Operating an Airsoft gas gun in extremely cold temperatures is not recommended Cold temperature will cause the Hop Up Bucking to harden reducing its effectiveness or cause the gearbox shell to fracture during operation rendering the gun inoperable Extreme Heat Do not keep Airsoft gun and batteries under direct sunlight for long periods of time Dust or Sand Dust or sand can get into a gun and cause malfunctions and or excessive wear Keep the gun covered whenever possible Use lubricant sparingly as lube naturally attracts dirt and other particles After use in a dusty area always field strip the gun refer to Disassembly Section and clean any areas you can reach with a soft lint free cloth Heavy Rain Keep the gun out of the rain and water This will prevent electrical failure and fluid build up inside the mechbox Dry gun completely with clean cloth and clean inner barrel if necessary 17 KM4A1 KMACQB DIAGRAM 531 04 e 236 E Kwa KM4A1 KM4CQB KM4A1 KM4CQB DIAGRAM 259 Sy Eme OO E in ae MC e usa M54 e e N 21 N43 A E u ES 22. Airsoft BB travels an upward trajectory path Turn Hop Up adjustment dial backward to decrease hop up Perfect Hop Airsoft BB travels long distance horizontally Inefficient Hop Airsoft BB travels a downward trajectory path Turn Hop Up adjustment dial forward to increase hop DECREASE ZEE INCREASE Kd HOP UP 204 12 4 KM4CQB FRONT AND REAR SIGHT ADJUSTMENT FRONT SIGHT ADJUSTMENT The front sight can be moved up and down when zeroing rear sight e Turn counter clockwise to lower the point of Impact e Stop turning when a click sound is heard WARNING If turned too far the front sight will come off REAR SIGHT ADJUSTMENT Flip the rear sight between general and precise aiming adjust the horizontal point of impact rotate the windage knob located on the rear of the sight adjust the vertical point of impact rotate the sight elevation knob located on the left and right side of the sight Rear Sight Assembly Rear Sight Windage Knob Small Large S Hole Use this position AC Use this position for precision firing E for full auto firing The sight assembly is marked in millimeter for precise adjustments Counter Clockwise Adjustment Knob 13 LATA DISASSEMBLY Note Before opening the receiver the piston must be in the forward position 1 Shoot in semi automatic mode 2 3 times to clear the barrel and reset the piston 2
3. OPERATOR S MANUAL KM4A1 KM4CQB TABLE OF CONTENTS Use of 2 Safety Guidelines es 2 3 Warranty and 4 5 CCI Cl WONG OO E 6 7 Funcions and Features TT m 8 Sogl 8 8 BES 9 Fire Selector 10 Battery amp Installailon 11 gi P S 11 12 Front and Rear Sight Adjustment rp evanida 13 Disassembly and Assembly Procedures pp 14 Cleaning and AON 15 REI E ETT 16 Operating Under Unusual 17 Diagram and Paris LASTS TEE E Eo 18 22 Kwa USE OF THIS MANUAL Before operating the Airsoft gun read this manual in its entirety Important safety topics and tips are discussed throughout all of the chapters It s important that the operator know the principles of gun handling safety and operation prior to firing the Airsoft gun SAFETY GUIDELINES WARNING Failure to follow safety guidelines may result In serious injury Safety Distance The effective shooting range is approximately 175 feet BBs fired from this Airsoft gun may t
4. Za EE Fuse Assembly 11 Kwa HOP UP SYSTEM The Hop Up device is one of KWA s standard features giving Airsoft BBs greater stability further travel and increased accuracy Airsoft BBs are light weight and can be affected by wind when fired With the Hop Up system the trajectory of the Airsoft BBs can be adjusted according to the shooting environment or surroundings HOP UP ADJUSTMENT Pull the charging handle to the rear the ejection port will open and Hop Up adjustment dial is revealed Pull and hold charging handle to the rear when adjusting Hop Up e Turn the Hop Up adjustment dial forward to increase hop up Turn the Hop Up adjustment dial backward to decrease hop up e Excessively turning of Hop Up adjustment dial forward can cause Airsoft BBs to jam Continued firing with a jammed barrel will cause damage to the gearbox e When jamming occurs immediately stop shooting and turn the Hop Up adjustment dial backward to decrease hop Remove jammed Airsoft BBs Before removing jammed Airsoft BBs be sure to return the hop up adjustment dial to normal position After removal of Airsoft BBs test fire 2 rounds to check for clearance Hesume adjustment KWA Airsoft guns are made with precision barrel use only new quality Airsoft BBs The use of recycled or low quality Airsoft BBs are the primary cause of jamming In most cases it can severely damage the gearbox and inner barrel Excessive Hop
5. 122 Mii M58 19 KM4A1 KMACQB PARTS LIST Parts Description Parts Description Parts Description Forward Assist Button 2 Swivel Cover Safety Lever Base nner Barrel Retainer 28 stock Latch Spacer safety Lever BB Ramp 29 stock Lever switch Assembly 99 96 7 1 Cylnder Head Main ylinder M55 Switch Chamber Block Upper Receiver Left M56 9 7 M Detente M35 Pbi Latch IBS M olt Plate Carrier Assembly M57 M Left earbox Shell Right 3 Hop Up Spindle Small Piston Assembly Disconnect 3 Hop Up Bar Spring Guide Assembly 66 Magazine Catch Ejection Port Cover Ejection Port Cover Lock Piston Plate ___ aT Charging Handle Switch Assembly pub E Anti Reversal Latch Spring IMMO Switch Assembly Selector Plate 48 Charging Handle Latch M71 Switch Assembly Main Spring 5 tock Swivel Charging Handle Sprin Hook i Flash Hider I2 Selector Plate Contact Retracting Stock M51 Tappet Plate 57 58 Selector Cover IM3 Switch Assembly Wire Retainer 37 Wre Holder Gearbox Shell Hop Up Adjustment Wheel Piston Head G 64 65 Pi 70 7 72 4 Tappet late Spring Magazine Catch Button Ejection Port Cover Lock switch Assembly Plunger Bott Catch 4 9 2 36 Up Adi 7 Up Spindle Small 8 15 Hop Up Spindle Large spring Guide Assembly 5 Trigger 0 i 2 i 3 i 7 8 M M7 Switch Assem
6. High Performance Bucking Fiber reinforced handguard with battery compartment e Removable carry handle Full metal alloy flat top receivers e Adjustable front and rear sights 6 position collapsible stock e Semi and Full Auto selective fire e Adjustable Hop up Individual test results may vary depending on brand of BBs and chronograph used KM4A1 KM4CQB SPECIFICATIONS KM4CQB Overall Length Retracted 67 31 cm 26 5 Overall Length Extended 275 65 cm 29 75 Outter Barrel Length 2283 cm 11 14 Inner Barrel Length 273 mm e nner Barrel Diameter 6 05 mm e Weight 2 91 kg 6 42 Ibs e Barrel thread 14 mm e Caliber 6 mm Magazine Capacity 350 rounds e Rate of Fire 20 RPS e Velocity 100 107 5 330 350 FPS Energy Output with 20g BB 1 14 Joules e Power Source 9 6v NiMh 7 4v or 11 1v 15c Li po Li Fe Special Features e KWA 2GX Gearbox e KWA 2G High Performance Gearbox e Fiber reinforced handguard with battery compartment e Removable carry handle Full metal alloy flat top receivers e Adjustable front and rear sights 6 position collapsible stock e Semi and Full Auto selective fire e Adjustable Hop up e High speed calibration Individual test results may vary depending on brand of BBs and chronograph used Kwa FUNCTIONS AND FEATURES KM4A1 The KWA KM4A1 Carbine is the first production AEG engineered specifically for the unparalleled perfo
7. Insert one end of the cloth into the hole in the cleaning rod adjust the length of cloth for smooth entry into the barrel b Wind the cloth around the cleaning rod c Insert the cleaning rod into the inner barrel turning the rod as you insert into the barrel d Remove the cleaning rod and check the cotton cloth for dirt Repeat steps a through c when necessary m ee rod Clean the remainder of the Airsoft gun with cotton tipped swabs or general purpose cleaning cloths BASIC TROUBLESHOOTING FOR RIFLE SYMPTOMS CAUSE SOLUTIONS Air Soft gun is not firing Selector set to Safe Mode Select Semi Auto or Full Auto Mode Dead battery Replace or Charge battery MEME ee C NNNM irc Ream 77 an _ Motor or Battery is hot Pinched wiring Return gun for professional care after short use Motor damaged or bad Return gun for professional care connection Semi Auto feature not Incorrect timing Set selector to full auto mode Dry fire 10 20 functioning properly rounds before returning it to semi auto mode Semi Auto feature not Internal failure Return gun for professional care per at all Fring cycle stows down cycle slows down Weak Recharge battery battery High pitch or grinding noise Gear may be damaged or Return gun for professional care Motor level not adjusted BB travels upward travels upward Excessive hop Excessive hop hop adjustment dial backward
8. SC X 2 Rear Sight Windace S M123 ear Box Set Pin 219 Cap Set Screw sight Windage Crew M124 ylinder O Ring levation Bar 123 ight Wi Hop Up Wheel S a 26 2 _ Rear Sight Elevation ME 295 295 C 28 G C 1 Pins X 2 In P Elevation Knob Pin 1260 45 Gas Tube Pin Front Sight Plunge S wivel Cover Pin Front Sight Housing Pins 1 Fjection Port Cover Pin Forward Assist Button Pin 99 131 Swivel Screw SP 3 X 20 Roll Pins Outer Barrel 1 Barrel Base Pins X 2 Outer Barrel KM4S 2 133 2 Weaver Rail Pin 135 Front Swivel Pin 3 3 3 0 0 138 Bolt Washer 158 159 Hop Up Bucking Kwa KM4 SERIES MAGAZINE DIAGRAM AND PARTS LIST MG 303 MG 319 MG 304 MG 306 ao MG Nov AL MG ue 0321 309 G e MG 326 MG 31 NN Parts Description Parts Description 199 1002 MG300 199 1002 MG310 Half Wheel Counter Weight 199 1002 MG301 Inner Magazine Housing Left 199 1002 MG314 Magazine Base Plate 199 1002 MC302 Inner Magazine Housing 199 1002 MG316 Sprocket Shaft Right 199 1002 MG317 Sprocket Wheel Pin 199 1002 MG303 BB Stop 199 1002 MG319 BB Stop Spring 199 1002 MG304 BB Compartment Cover 199 1002 MG320 Coil Spring 199 1002 MG305 Gear 1 199 1002 MG321 Counter Weight Spring 199 1002 MG306 Gear 2 199 1002 MG323 Half Wheel Retainer Clip
9. hop adjustment dial backward adjustment dial backward BB travels downward downward P Insufficient op Insufficient op hop adjustment dial forward hop adjustment dial forward adjustment dial forward BB double M or rolling Excessive oil in chamber Fire 200 rounds to eliminate excessive oil out the barrel Hop Up unit is contaminated Up unit is contaminated Clean Hop Up unit with supplied cleaning Clean Hop Up unit with supplied cleaning rod Up unit with supplied cleaning rod Hop Up unit may be damaged Up unit may Hop Up unit may be damaged damaged Return gun for professional care gun for Return gun for professional care care Up unit can t be adjusted Damaged adjustment dial Return gun for professional care or internal parts ner barelis jammed barrel is ner barelis jammed Use of recycled or low quality BBS of Use of recycled or low quality BBS or low quality BBs Use KWA Perfect BBs or other Use KWA Perfect BBs or other high quality BBs quality BBs Inner barrel is contaminated inner barrel with supplied cleaning rod en Inner barrel is damaged Return gun for professional care Hi cap magazine not magazine not feeding Magazine has been wound has not been wound Wind wheel underneath magazine wheel underneath Wind wheel underneath magazine BBs are lodged inside the Shake or tap magazine to unclog the BBs
10. is beyond it The Airsoft gun should never be fired at surfaces such as rocks glass water or other hard surfaces where BBs are likely to ricochet in unpredictable directions WARNING Adult supervision is required for any person under the age of 18 Failure To Fire If the Airsoft gun fails to fire misfires or malfunctions do not look into the gun barrel BBs can become lodged into the chamber and serious eye injury may occur Maintain Your Gun Properly Performing proper maintenance as outlined in this manual ensures that your Airsoft gun will be safe to shoot and will perform to its designed specifications for many years Alterations modifications or adjustments may damage your Airsoft gun make it unsafe to shoot and will void all warranty claims Store Your Gun Safely Always store the Airsoft gun in a safe place and out of the reach of children Always transport the Airsoft gun in a carrying case Never display the Airsoft gun in a public place Keep the safety engaged and remove the magazine before storing the Airsoft gun NOTE IT 15 YOUR RESPONSIBILITY TO TAKE EVERY REASONABLE PRECAUTION TO ENSURE THE SAFE STORAGE AND TRANSPORTATION OF YOUR AIRSOFT GUN Orange Tip The orange tip on Airsoft guns helps Law Enforcement distinguish between the replica guns from their real firearm counterparts Altering the coloration or markings required by state or Federal law so as to make the product look more like a firearm is dangerous an
11. periods The following are not covered by the warranty 1 Any product which is not imported and distributed in the U S A by KWA PERFORMANCE INDUSTRIES INC 2 Any products not purchased in the U S A from an KWA AUTHORIZED RESELLER Note KWA AUTHORIZED RESELLER can be identified by KWA AUTHORIZED RESELLER sticker displayed in the store If you are uncertain as to whether a dealer is a KWA AUTHORIZED RESELLER please contact KWA PERFORMANCE INDUSTRIES INC as listed above 8 Damaged deterioration or malfunction resulting from a Accident act of nature abuse misuse neglect unauthorized product repair opening of or modification or failure to follow instructions supplied with the product b Repair or attempted repair by anyone not authorized by KWA PERFORMANCE INDUSTRIES INC c Removal of the orange safety tip 4 Use of the product outside the U S A 5 Damaged batteries or improper use of bullets BBs or non approved propellants ie Propane Red Gas 134a etc 6 Use in industrial commercial and or professional applications What KWA Will Pay For If during the applicable warranty period from the date of the original purchase your KWA product is found to be defective by KWA Performance Industries Inc KWA Performance Industries Inc will repair or at its option replace with new used or equivalent model the defective product without charge for parts or labor How To Obtain Warranty Service If your product needs ser
12. 199 1002 MG307 Winding Wheel 199 1002 MG324 Phillip Screws X 5 199 1002 MG308 BB Spindle 199 1002 MG325 Magazine Base Plate Screw 199 1002 MG309 Counter Weight Wheel 199 1002 MG326 Base Plate Nut 22 MMD12 4 V01 R2011 06 29 KWA Performance Industries Inc 18571 E Gale Ave City of Industry CA 91 748 T 626 581 1777 F 626 581 0777 www kwausa com Copyright September 2009 KWA Performance Industries Inc All Rights Reserved
13. ANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OUR LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT AT OUR OPTION OF ANY DEFECTIVE PRODUCT AND SHALL IN NO EVENT INCLUDE INCIDENTAL OR CONSEQUENTIAL COMMERCIAL OR PROPERTY DAMAGES OF ANY KIND WE ARE NOT RESPONSIBLE FOR PRODUCTS LOST STOLEN AND OR DAMAGED DURING SHIPPING SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AND IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU This warranty gives you specific legal rights but you may also have other rights which vary from state to state This Warranty may not be altered other than in writing signed by an officer of KWA Performance Industries Inc KWA Performance Industries Inc 18571 E Gale Ave City of Industry CA 91748 1339 626 581 1777 www kwausa com TAZA SPECIFICATIONS KM4A1 Overall Length Retracted 77 47 cm 30 5 Overall Length Extended 85 73 cm 33 75 Outter Barrel Length 38 1 cm 15 Inner Barrel Length 395 mm e nner Barrel Diameter 6 05 mm e Weight 3 03 kg 6 68 Ibs e Barrel thread 14 mm e Caliber 6 mm Magazine Capacity 350 rounds e Rate of Fire 20 RPS e Velocity 118 125 5 390 410 FPS Energy Output with 20g BB 1 49 Joules Power Source 9 6v NiMh 7 4v or 11 1v 15c Li po Li Fe Special Features e KWA 2GX Gearbox e KWA 2G
14. N PERIOD Airsoft guns like many other products require a break in period to ensure the optimal performance This break in period allows the spring piston gears and other moving parts to be seated and become more consistent in their movements Every new KM4 Airsoft gun spring is manufactured with more tension than is required this break in period will allow the spring to settle and operate at the specified FPS range The KWA 4 Airsoft gun s break in period will require a minimum of 2000 rounds During this break in period the Airsoft gun will require more cleaning because it will expel excessive grease from the gearbox After the break in period the gun will operate within factory specification The accuracy of the brass barrel will also improve as you continue to use the gun 8 4 KM4CQB LOADING HIGH CAP MAGAZINE 1 Release the magazine from the Airsoft gun by pressing the magazine release button 2 Open the magazine top plate and pour Airsoft BBs into the chamber Close the plate when the chamber is full 3 Turn the winding wheel on the bottom of the magazine to tighten the spring tension This will allow the Airsoft BBs to feed through the top of the magazine 4 Insert the magazine into the Airsoft gun until it clicks into place NOTE Spring tension will unwind as you fire the gun Continue winding the magazine regularly as necessary to empty the high cap magazine Loading safety tips e Switch
15. Remove the Rear Pin only from lower receiver with the provided Allen wrenches 3 Use 1 wrench to hold the cap screw and one to turn the set pin 4 After removal of the cap screw use the allen wrench to push the pin out 5 Pull the Upper receiver up 6 Slide out the inner barrel with Hop Up assembly M RD eec e f sees WARNING Before removing any parts be sure the fire selector is set to SAFE Always place safety cap on the barrel tip when servicing your gun ASSEMBLY 1 Insert the inner barrel and Hop Up assembly into the upper receiver 2 Secure the Hop Up assembly into the upper receiver Push down the upper receiver to close 3 Align the pin holes Insert Pin and use the allen wrench to tighten the cap screw ja rr e Ej KM4A1 KM4CQB CLEANING AND LUBRICATION WARNING Unload and clear the Airsoft gun of all BBs before cleaning Cleaning Procedure The Airsoft gun barrel should be cleaned and lubricated after each shooting session Regular cleaning prevents the effects of BB residue buildup and ensures all parts are lubricated properly 1 2 6 15 Ensure that the safety is engaged Disable Hop Up by dialing to the normal position Remove the magazine and clear the chamber of loaded BBs Disassemble the receiver see Disassembly section Steps to use cleaning rod a Cut a piece of clean cotton cloth to 1 inch by 0 5 inch size
16. bly s 2 KM4A1 KM4CQB KM4A1 KM4CQB PARTS LIST Parts Description Parts Description Parts Description 161 Forward Assist Button 244 Locking Clamp 20770 249 Fuse 62 Chamber Block Spring 250 Power Supply Wire 63 Charging Handle Spring 252 Gear Box ea M80 Trigger Spring 65 257 Lower Hand Guard lash Hider Spring 81 Stock Tube Cap 258 71 Hop Up Bar Spring 8 Stock Tube Retainer 259 Rear Sight 73 Magazine Catch Spring 3 eceiver End Plate 260 Windage Knob 74 Motor Tension Spring Elevation Knob Dial Base Trigger ae 75 Ejection Port Cover Spring zl 8 ail Retaining Block We 262 Elevation Knob Dial Ejection Port Cover Lock 91 wivel Front 176 Spring 265 arrel Assembly Block M97 Bevel Gear 1 Stock Bolt Spring 266 Weaver Rail Bolt Plate Selector Spring Hand Guard Ring M101 Trigger Guard Plunger Barrel Nut me Motor Adjustment Screw Wire Clamp Screws X 2 Carry Handle Lock Rear B M115 Carry Handle Lock Screws Rear Sight Housing Base im t mm M117 M119 206 Motor Plate Screws X 2 Metric 3 Carry Handle Locking Plate Selector Screw Hand Guard End Cap Take Down Pin Rear Ramp Screws X 2 121 Locking Washer Gearbox X 4 Screw M3X3 SCX2 287 Gas Tube M122 Switch Assembly Carry Handle Knobs X 2 215 Windage Knob Set Screw Windage Knob PI Piston O Ring indage Knob Plunger 218 Screw M3X8
17. d may be a crime Operator assumes all risks and responsibility when doing so Hazards of Being Mistaken for a Real Firearm Airsoft guns have been mistaken by Police and Law Enforcement as real firearms A confrontation with law enforcement while carrying an Airsoft gun can result in serious injury or even death It is strongly advised to operate the Airsoft gun at a safe and legal location In the event that you are approached by Law Enforcement personnel you must comply with their instructions immediately to avoid an incident Alcohol Medications and Drugs Do not handle or operate your Airsoft gun while under the influence of alcohol medication or drugs Your Responsibility Your Airsoft gun is well engineered and manufactured to the highest standards It was carefully inspected before it was packaged and shipped from our factory Its safe use depends on you alone You are the ultimate safety device Like many other devices your Airsoft gun is safe unless handled in an irresponsible or uneducated manner 3 Kwa WARRANTY AND SERVICE KWA Performance Industries Inc is committed to serve our customers with the finest quality products the highest level of service and customer satisfaction Because of this we offer a 45 day warranty on all KWA products we import and distribute What is Covered Except as specified below this warranty covers all defects in material and workmanship KWA products occurring during the above warranty
18. ravel further than intended Make certain that you have an adequate backstop Eye Protection Eye protection should be worn at all times when both shooting and maintaining your Airsoft gun Protect your eyes from silicone spray and BBs under spring pressure while performing maintenance on your Airsoft gun Assume Every Gun is Always Loaded Until you are certain the chamber is empty treat every gun as if it were loaded Do not assume the chamber is empty based on your memory or someone else s words Always remove the magazine and visually check to confirm the chamber is empty Beware of Barrel Obstructions Ensure the Airsoft gun barrel is free of obstructions before you fire the gun Even the smallest obstruction such as lubrication or a stuck cleaning patch can cause a misfire or malfunction Muzzle Control Always keep the muzzle of the gun pointed in a safe direction Never point the muzzle at a person or object that you do not intend to shoot Keep Your Safety On Keep the gun s safety on until your sights are aligned on your target and you are ready to fire Keep Your Finger Off The Trigger Keep your finger off the trigger and out of the trigger guard until your sights are aligned on your target and you are ready to fire WARNING Airsoft BBs can be a choking hazard Keep them away from children KM4A1 KM4CQB SAFETY GUIDELINES Identify Your Target and Backstop Before you pull the trigger make certain of your target and what
19. rmance of today s advanced battery technology Lithium Polymer LiPo LiPo batteries provide higher capacity and superior performance surpassing the more common Nickel Metal Hydride NiMh batteries However this powerful battery requires the highest quality of internal components To handle the extra power of LiPo batteries the is equipped with a reinforced metal gearbox utilizing KWA s exclusive six 9mm ball bearing bushing combination and heat treated precision metal gear sets Heavy duty springs and high torque motors are matched for optimum performance High grade metal alloy are used for the production of the upper and lower receivers The KWA KM4A1 Carbine was engineered to outperform the competition offering ultra high performance and dependability straight out of the box KM4CQB The 4 was designed and engineered especially for close quarters battle scenarios with a 350 FPS limit After initial break in period the KM4 CQB shoots consistently below 350 FPS but fires more than 20 rounds per second using 20 gram BBs The KM4 CQB is LiPo Ready and share all the standard features found on the 4 All of the internal components have been finely tuned and recalibrated to provide the maximum rate of fire while maintaining the 350 FPS limit PACKAGE CONTENTS 1 KM4A1 KM4CQB Airsoft Gun 2 Allen Wrenches For cap screw removal 1 Safety Cap 1 Sight Adjustment Tool 1 Cleaning Rod 1 Owners Manual BREAK I
20. the selector to safe Be sure the safety cap is on Keep your finger off the trigger at all times WARNING Use only 6mm high grade BBs Using low grade BBs will damage Airsoft gun NOTE Use 0 25g or heavier BBs for better performance Magazine Top Plate Magazine Release Button oH LL AY ms annm Winding Wheel FIRE SELECTOR SWITCH 1 Safe In Safe mode the gun will not fire For safety reason you should keep the switch in Safe mode at all times when you are not ready to fire 2 Semi Auto In Semi Auto mode the gun will fire one shot for each time you pull the trigger 3 Full Auto In this Full Auto mode the gun will fire continuously as long as the trigger is depressed KWA AUTO WARNING Do not pull the trigger when switching the fire selector 10 KM4A1 KM4CQB BATTERY INSTALLATION 1 Setthe fire selector to safe mode Place the safety cap on the barrel end Slide the retaining ring back and remove the lower part of the hand guard 2 Place the battery into the lower half of the hand guard Push the connector plugs together firmly until they click into place 3 Replace the lower battery cover and slide the retaining ring back into place Connector Plug Hand Guard FUSE To replace the fuse open the hand guard by following the same procedure as the battery installation Open the fuse assembly and replace the fuse with a 15A glass fuse
21. vice it may be taken or shipped to KWA Performance Industries Inc The following procedures apply whenever your unit must be transported for warranty service e You must go to Help Desk at www kwausa com support to obtain an RMA number THE RMA NUMBER MUST BE CLEARLY MARKED ON THE OUTSIDE OF THE PACKAGE PACKAGES WITHOUT AN RMA NUMBER CLEARLY MARKED WILL BE REFUSED AND RETURNED TO THE SENDER You are responsible for transporting your unit or arranging for its transportation f shipment of your unit is required you must pay the initial shipping fee but we will pay the return shipping charge if the repairs are covered by the warranty WHEN RETURNING YOUR UNIT FOR WARRANTY SERVICE A COPY OF THE ORIGINAL SALES RECEIPT MUST BE ATTACHED e You must include the following RMA number your name address daytime telephone number model and serial number if applicable of the product and a description of the problem 4 KM4A1 KM4CQB NOTE THE RMA NUMBER MUST BE CLEARLY MARKED ON THE OUTSIDE OF THE PACKAGE PACKAGES WITHOUT AN RMA NUMBER CLEARLY MARKED WILL BE REFUSED AND RETURNED TO SENDER NO EXCEPTIONS This Warranty is Only Valid in the United States If your product does not require service but you have questions regarding its operation please contact our Technical Services Department as listed below THIS WARRANTY 15 EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING WITHOUT LIMITATION WARR
Download Pdf Manuals
Related Search