b) BiColor model
Contents
1. Gold Mt plate On Lighting Rail Due to the shortened yoke on Prime Location LED when hanging the fixture from rail or pipe fixture should be positioned upside down see photo If using with gel frame or any other front light controls installed be sure that top corner accessory guide lock on the fixture is fully engaged Attach clamp tightly to yoke of fixture according to clamp mfrs instructions Hang clamp on pipe or grid and tighten the large screw so that the clamp and fixture are securely mounted Attach safety cable between the fixture and the rail for necessary security 16 25 41 3 cm i atioie 4 BiCOLOR 12 25 31 cm 4 75 12 cm Saige s PrimeLocatioited Performance Each fixture has installed LEDs totalling 5800 6000 lumens Foot Candles Lux foot candles x 10 8 Full Day Tung 365 98 46 27 Full Daylight 196 54 25 15 Full Tungsten 180 50 23 14 Beam Angles Points at which intensity drops to 50 of maximum Foot Candle readings taken at center of beam using a Minolta CL 200 meter Color Full Daylight Tungsten blend 4000k aprox Full Daylight 6000k Full Tungsten 3000k Differences in LED color output levels as well as electronics can influence the com bined color output readings Color Rendering Index 90 Fuses amp Power Consumption Note Most electrical equipment briefly consumes a higher amount of electrical current durin2. variance for each color At full day full Note When using the AC bridge PowerCon tungsten mix the 4 digit LED display will connection pay attention to the total read 0000 and the Color Indicator Scale will ade consumption of the chain on show a reading in the middle As you shift the AC circuit Do not overload color in either direction you will see both displays reflect the changes Color Change Buttons Cool Warm Fuse Always power down amp unplug the fixture before changing its fuse Open the fuse holder with a phillips head screwdriver to replace the fuse Lowel Prime Location LED s use fuses rated at 3 Amps and 250 Volts Prime Location Accessories Lowel Prime Location Light Control Accessories mount on the front of the fixture using the 2 slots The rear slot closest to the LEDs should be used for the gel frame with the front slot used for either of the below listed accessories Make sure top corner fixture Accessory Lock is engaged to secure accessories Honeycomb Grid Honeycomb grids control the spill of the light by attaching to the front of the fixture The grid is available in 20 degree dispersion 20 Honeycomb Barndoor Softening Set Due to the multi point source nature of most LED fixtures it is common to have an undesired multi shadow effect when using barndoors to trim the beam This set includes a 4 way barndoor subtle Output Loss aprox 54 diffusion gel and Gel jawz Code PL
3. 132 clips to minimize ee multi shadow while still allowing a visible barndoor cut Includes 4 way adjustable Barndoor Prime Lite Diffusion Gel Lowel Gel jawz 4 Code PL 120 Problems repairs amp info Repairs problems suggestions be made only by Lowel or by and requests for brochures catalogs a qualified electrician instructions and parts lists can be Lowel Prime Location LED equipment is a prod handled through your Authorized Lowel uct of the ongoing collaborative relationship Dealer Distributor or directly through between Lowel Light and Fluo Tec Mexico Lowel Electrical repairs should AC DC Power Switch Center Off AC Input AC Bridged Output Fuse Suggested Stands Uni Sr Stand KS Jr Stand Code UN 66 Weight 3 3 Ibs 1 5 kg Size 22 5 57 2 cm folded Maximum height 7 2 2 m Code DT 33 Maximum height 7 7 2 3 m Collapsed length 2 4 65 cm AX se 3 5 Ibs 1 6 kg Safety Cable 3 Code CM 50 omOQ Weight 2 oz 57 g AC Use Lowel Prime Location LEDs use Powercon connector AC cables The fixture will auto set itself to international voltages See the listed cables if adapting for use in another country For IP 65 use do not use switched AC cables Also Prime Location LEDs can be ganged together using AC Bridging cables when AC outlets are scarce With each fixture drawing aprox 1 amp a 20 amp circuit could accommodate 15 fixt
4. BiColor Prime Location LED Instructions rm PrimelocationLED Lowel Prime Location LED equipment is a professional lighting system Read these instructions as well as acces sory instructions and applicable warnings before operating m Do not leave fixture unattended For fixed stationary use in studio s theaters and similar locations m Not for household use Use only for photographic lighting video amp film imaging m Always unplug unit before changing fuse m Never bypass plug s ground pin E Do not interfere with unit s ventilation m Do not operate unit with Accessory Barndoors closed m Make sure clamp is tightened at yoke m Always use with supplied Lowel AC Cable m Always use Safety Cable when attaching to overhead pipes or grids m Make sure Accessory Lock is engaged to to secure accessories Mounting the Fixture On Stand The recommended Lowel Stand for the light is the Uni 66 stand UN 66 or larger Set the stand risers at less than full extension for most stable operation and if tilting the light down make sure 1 leg of the stand is extended Straight out in front of the light for best balance Prime Locations yoke is placed off center vertically in the unit This is to allow a more full tilting range Make sure to tighten the side locking knob fully to prevent slippage Female 5 8 Stand Fitting Safety Cable LED Warnings m Avoid lo
5. Prime Location LED Operation AC DC Power Switch Operation The Prime Location LED can be powered Turning on the Power in either AC or DC by AC or DC with attached V lock or Anton operation switch causes the fixture to light Bauer type battery Press the Power Switch to at whatever dimming level it was at when last the left side for AC or the right side for DC powered down factory shipped at 100 In the switch s middle setting the fixture The unit will retain its previous dimming is powered off level even if unplugged AC Power In amp Out Dimming 1 100 From the wall outlet the Prime Location LED The Prime Location LED fixture s full output AC cable plugs into the top Powercon level is dimmable manually on the rear of Connector shown above with a twist lock the unit regardless of its color setting To action Be sure the cable is securely locked dim the light to a desired level press the Up The fixture will auto set itself from 90 240 amp Down buttons setting dimming level from VAC Use the proper cable for the country 1 100 as seen in the 4 digit LED display of use The AC Bridged Output allows Changing Color jumper PowerCon cables to pass AC power The Up Down CLR buttons will shift the from fixture to fixture in a chain of Location color output from Warm tungsten to Cool Prime LED s This can be helpful when dayli one sees ylight There are 99 total steps of access to individual AC outlets is limited
6. g startup ignition Consult the below chart to con firm that your electrical wiring is sufficient for the fixtures used All fuses must be rated at 250VAC Lowel Prime Location LED s auto set from 90 240 VAC Fixture consumes 82 Watts and has a Power Factor of 97 110V 240V Model Fuse Nominal Peak Nominal Peak Current Ignition Current Ignition Current Current ALL 3A 250V O714A 0 97A 0 403A 0 61 A Using Prime Location LED in Rain or Dust Sand Storms Prime Location LED s IP 65 rating means the fixture is sealed against dust amp sand and protected from water splashing on it from any direction such as a rainstorm AC Use When using the fixture with AC power in rain or dust environ ments it will be protected at the fixtures locking Powercon connec tor Also ensure that the AC outlet the fixture is plugged into is pro tected When not in use make sure AC connections have their rubber covers securely in place DC Use Prime Location s V Lock or Gold Mount battery plates are also sealed against rain amp dust when not in use For IP 65 protection you must also use batteries that are rated for IP 65 use Before attaching in damp environments make sure the battery pins are wiped dry BiColor Lowel Prime Location LED Control Panel Prime LocationLED Battery Plate Connection Color Indicator Scale Cool Warm LED Display Dimming Buttons Down Up A g BiCOLOR KNT LED
7. oking directly at the LED s for extended periods of time m LED s take time to reach standard operating output level and frequently have slightly higher output during the first 1 2 hr when powered up IP Ingress Protection m Prime Location LED is protected against all dust sand and dirt as well as rain D CE Intertek Accessory Lock Female 5 8 Stand fitting For use on stand only Allows mounting the fixture on 5 8 male stand stud Stand fitting comes with a locking washer and a flat washer Mount with the locking washer above the flat washer on the top side of the yoke under the bolt head Attach the female stand fitting tightly and rotate yoke so it is now on the underside of the fixture Tighten yoke clamp locking lever and place female stand fitting over stand making sure that its locking screw is loosened enough to allow the fitting to completely fit over the 5 8 stand stud Tighten knob mak ing sure its screw is under the safe ty cut of the stand fitting stud Add additional weight to base of stand for increased stability Lowel C Clamp FLS 803 Specs amp Performance BiColor Models 16 40 6 cm Supplied with Gel Frame selected Battery Plate safety Cable 5 8 Female Stand Fitting and 10 unswitched AC Cable PC1 808 Other AC cable connection options are available Weight 10 5 Ibs 4 76 kg Code PL 01VBC BiColor V lock plate Code PL 01ABC Bicolor
8. ures Do not overload AC circuits 16 Lowel Powercon AC Eurocord Switched PC1 801 y QA Switched 16 Lowel Powercon AC UK Cable Switched PC1 802 16 Lowel Powercon AC Cable Switched PC1 800 oo Male Switched Switched Female Female Male Female Male 12 Lowel Powercon AC Cable Unswitched 12 Lowel Powercon AC Eurocord Unswitched PC1 810 12 Lowel Powercon AC UK Cable Unswitched PC1 812 Unswitched Female Male Unswitched Female Female Male Male Unswitched 12 Lowel Powercon AC Bridging Cable PC1 805 Female Unswitched Male V Lock Mount Code PLPLVLMNT Anton Bauer Gold Mount Code PLABMNT Battery Use Battery run time will vary with battery model age and charging level Both Location Prime battery plates are user removable amp swappable via a multi pin connector beneath the plate For use in rain or dust sand make sure battery is also rated for IP 65 use ver 1 0 Lowel Light Mfg Inc 2014 927 Lowel Light Manufacturing Inc 90 Oser Avenue Hauppauge N Y 11788 a gi Call 800 645 2522 or 631 273 2500 Fax 631 273 2557 e mail info lowel com www lowel com
Download Pdf Manuals
Related Search