User Manual for GC0101
Contents
1. Internal negative supply Zero volts To connect a switch or contact to an input simply connect the switch between the and IN terminals and a wire between the and IN terminals The reverse is just as suitable i e that you connect a wire between and IN and place the switch between and IN Model LE WHR GSMCOMMANDER COM MICRO COMMANDER PROGRAMMABLE TELEMETRY CONTROLLER PWA IN STATUS You may need an input to activate when power is supplied from some other unit A good example will be a burglar alarm that applies power to the wires going to the siren In such a case it will be a simple matter of connecting the positive wire to the IN input and the negative wire to the IN input Polygon Technologies All rights reserved Page 10 Model E GC0101 HHL SSMCOMMANDER COM MICRO COMMANDER PROGRAMMABLE TELEMETRY CONTROLLER 1 CAS A TA 2008 710 PWR IN STATUS Supplies 12V when active Other Appliance Please keep in mind that this input is designed for 3V to 20V operation If you require to connect a voltage above 20V to these terminals you should connect a resistor in series with the input as shown below Model GC0101 HWH GSMCOMMANDER lt om MICRO COMMANDER PROGRAMMABLE TELEMETRY CONTROLLER IEAS A k TA 2008 710 PWR IN STATUS Above 12V when active Input Voltage range Required Series resistor 20V 40V DC 1K ohm The and termin2. a Current analog input reading 0 255 Unit s serial number f Unit s current firmware version b Battery voltage in volts p Current power status of mains s GSM signal strength in c Airtime credit remaining local currency i Current status of input 0 OFF 1 ON o Current status of output 0 OFF 1 ON v Last received voice call number m Last received message number q Last received message text r Carriage Return 0x0D n Line Feed 0x0A VV VV VV VV VV VV VV Y For example Serial no s signal is s will send Serial no 100641 12345 s signal is 75 Polygon Technologies All rights reserved Page 28 The Micro Commander supports time constraints which can be setup for any statement Time constraints will prevent a statement from triggering outside of the preselected times and days of the week The Micro Commander can also be configured to trigger a statement at a certain time on a certain date or group of days The current time and date can be set in one of two ways either by SMS or by clicking on the tab Set to PC time in the software interface under the Status Tab By means of SMS you would send a special SMS message to the Micro Commander containing the text SETTIME The cellular network supplies the time and date with any message that is sent and the Micro Commander sets its own time according to this Pleas
3. 65M COMMANDER User Manual for GC0101 Applicable to software package Version 7 22and up Revision V7 0 Last Edited 7 April 2014 Before Attempting to connect or operate this product please read these instructions in its entirety This manual is intended to provide detailed technical specifications and explanations to the basic user as well as the more technically minded person This manual is a live document and will be updated often with new information Please insure that you have the latest version by checking our website at http www gsmcommander com Changelog SJD 7 Apr 2014 Document created POALUNES cc axucmssmaueedwessasenseaewevennemcanuensaseseawenduuaaaeesseeweennabeanawsaaaronsdedsssussesceensens 3 Specifications iscaciceaacariuausseasdasoravamsawedeniawbanaienennacecedstoseeusbandeusmedsenmiunensaeawaus 4 System TEQUINCMENES sic cdaccaaddaoncatandauedisceansshedudeeennsaienssegiaadeetenanaeuesenved 4 DIMENSIONS vccissaviscessiovemsanvndansaienadnadacwsnaaaeiseinna Seaaseecieneesaeseepeaeemebaupead abieaweceonens 5 DARIELA Oa 3 cc sancvnnsnstarenerdaniuaese candies E T E E E ees ensendens 6 ENVIrOnNMEN Cossee ec ee ea and se EEE EIN E aa EE E EE E S 6 LONLA 0 01 d EEE E E E 6 USB PO cox ote r a A E E E E EEEE E E EEEE E ER EE ESN 6 SIM Car aenea eas EEEE E TE een EE E E E E E EA EOE EA 6 ANTENNAS rea aE E AOE E N EE E OE a E S E E et 7 Software IS AA CIONS en on de tee de no neo ie 7 Mountini s ccsteadsdec
4. C to 80 C Digital Input Opto isolated Inputs draw 2 45mA depending on voltage Can accept any DC signals of any type including gt Dry Contacts gt Open Collector NPN gt Closed Collector PNP gt DC Voltage 3 20V Digital Output 1 x SPDT Relay Contact rating 8Amp DC 10 48V or 4amp AC 110 400V Expandable to maximum of 32 10 Connector type Pluggable terminals GSM 850 900MHz Output Power Class 4 33dBm 2W GSM 850 900MHz Sensitivity 107dBm GSM 1800 PCS 1900 Output Power Class 1 30dBm 1W GSM 1800 PCS 1900 Sensitivity 106dBm The setup software requires a PC with the following specifications Operating system Win2000 WinXP Vista Win7 Win8 Computer Architecture Pentium 2 or higher IBM compatible PC Disk space 20MB Ports 1 x free USB port Polygon Technologies All rights reserved Page 4 Polygon Technologies All rights reserved Page 5 Due to the make up of the Micro Commander and it s electronics we STRONGLY advise that it not be installed in close proximity to a variable speed drive or any other electrically noisy equipment DO NOT install the Micro Commander into a metal enclosure unless an antenna is mounted on the outside of the enclosure The Micro Commander has a 2 1mm DC jack connector where a power supply must be connected The power supply should have the following specificati
5. Technologies All rights reserved Page 27 It is often required to have more than a single action to be executed for a single Trigger condition For instance if your home alarm is triggered you may want to activate an output that in turns switches on a loud alarm or perhaps pulls the trigger on a rigged up shotgun and you also want to receive a voice call and an SMS as well The Micro Commander will always execute all statements that are eligible to trigger due to a certain event in other words the first statement that is triggered does not void or eat up the event So to take our example we will have a set of statements like Statement 1 IF input 1 becomes Active THEN Place Voice Call to lt your number gt Statement 2 IF input 1 becomes Active THEN Send XYZ via SMS to lt your number gt Statement 3 IF input 1 becomes Active THEN Activate Output 1 for 10 minutes If input 1 becomes active all the above statements will trigger and their associated actions will take place The action for the first statement will be executed first Alternatively IF Statement X Triggers could have been used See 8 1 15 The Micro Commander support the use of parameters in predefined messages This allows the user to insert and refer to certain values in message The following is a list of all available parameters case sensitive together with their descriptions gt t Current time HH MM SS d Current date DD MM YYYY
6. confirmation message This set of commands allows you to override the GPRS settings that the Micro Commander may have been configured with and can only be sent from the administrator number These override settings are non volatile which means their effect will remain after power has been cycled To configure the Micro Commander to connect to server via a South African network you must send ADMIN GPRSSETUP PRODUCTION To turn off GPRS functionality you must send ADMIN GPRSSETUP OFF To disable any override and go back to whatever settings were specified by the configuration you must send ADMIN GPRSSETUP SETUP If you need to specify the username and password of your APN Access Point Network you must send ADMIN SETSERVER lt apn gt lt username gt lt password gt UCGPBUPGVQZG The Micro Commander will reply with a confirmation message for each of the above This command can only be sent from the administrator number To re open GPRS you must send RESET GPRS The Micro Commander will reply with a confirmation message _ Polygon Technologies All rights reserved Page 20 This set of commands allows you to override the GPRS logging interval that the GSM Commander may have been configured with and can only be sent from the administrator number These override settings are non volatile which means their effect will remain after power has been cycled ADMIN GPRSSETUP LOG5 GPRS logging interval will
7. firmware and software may be copied or reverse engineered Polygon Technologies CC reserves the right to make changes to contents of this manual without notice at any time Polygon Technologies All rights reserved Page 35 Polygon Technologies may be contacted at Email Info gsmcommander com Web www gsmcommander com Telephone 27 0 21 9817062 Fax 27 0 86 6823310 Postal Address PO Box 1655 Brackenfell 7561 South Africa Polygon Technologies All rights reserved Page 36
8. if it responds Section 5 12 If it does respond the unit is operating correctly Cause 1 Incorrect operator selection You may have chosen the incorrect operator settings under the SETTINGS TAB in the software interface If your operator is not in the list then choose Other and define the airtime checking and please call me numbers respectively If available Polygon Technologies All rights reserved Page 34 Cause 2 Do Not Check Airtime is enabled You may have disabled airtime checking by ticking the box labeled DO NOT Check Airtime which is located in Supplementary Data Services under the SETTINGS TAB Cause 3 Reception problem You may have bad reception in your area preventing the unit from communicating with the network Please check using a regular cellular phone that there shows 1 2 bars of signal right next to the Micro Commander Refer to Section 5 5 Antenna Mic O Com na der do es Cause 1 Caller ID on phone is disabled Your Caller ID feature on your phone may be deactivated Please refer to your phone s manual on how to enable this feature Cause 2 Bad configuration You may have configured the unit incorrectly Make sure the number you are calling from is stored in the Numbers List on the Micro Commander The Micro Commander is guaranteed for a period of 24 months against defects in materials or workmanship Should your product become defective during the guarantee
9. this install program Launch GSM Commander V7 0641 Screen 6 GSM Commander V7 06 Clickteam Install Creator Copyright 1999 2011 Clickteam http www clickteam com This install program has been created with the freeware version of Clickteam Install Creator a simple and powerful install maker Visit our Web site and discover Clickteam Install Creator as well as our game and multimedia creation tools PS the product you have just installed has not been created by Clickteam please directly contact its author or publisher for any question about it Polygon Technologies All rights reserved Page 9 The Micro Commander is housed in a very durable ABS casing which has 4 protruding tabs which allows it to be mounted firmly to any surface by means of a screw There is also a DINra l mounting kit available separately Please note The Micro Commander is not water or weatherproof The Micro Commander must be mounted indoors or inside an appropriate IP65 rated weatherproof enclosure The guarantee does not cover damage resulting from water ingress DO NOT mount the Micro Commander inside a steel cabinet unless you also mount a separate antenna on the outside of the cabinet Suitable antennas can be ordered from Polygon Technologies The Micro Commander itself provides 1 signal inputs The input has the following 4 terminals Internal positive supply 14V IN Positive input IN Negative input
10. time Pause Activate for a time e Activate Leave Activated e De Activate Leave De Activated Change State If the user chooses gt Activate for a time it will Activate the selected output for the selected number of seconds specified gt Activate for a time Pause Activate for a time it will Activate the selected output for the selected number of seconds specified The output will remain off for a selected period after which it will again activate for the selected number of seconds gt Activate Leave Activated it will Activate the selected output and leave it activated The inverse applies to De Activate Leave De Activated gt Change State it will either change the state of the selected output meaning that it will active it if it was de activated and vice versa 8 2 2 THEN Send Message A statement containing this Action will send a message via SMS to each of up to 6 selected recipients or a message via Serial port or a message to our server The user can choose between the following fourteen options Plain Message Input Output Status General Status Global Input Status Global Output Status Please Call Me e Log Status to Sever If the user chooses gt Plain Message it will send a predefined message either via SMS to each of up to 6 selected recipients via the serial port or to server gt Input Output Status it will send a predefined m
11. D labelled GSM shows the status of the internal GSM cellular engine while the green LED labelled STATUS shows the status of the Micro Commander as a whole The following table shows how one can determine the current status GREEN LED STATUS gt Solid On a Busy Booting gt on for 500ms off for 500ms slow flash All OK gt on for 200ms off for 200ms fast flash m e e e e e e E Airtime running low gt on for 10ms off for 500ms 2 short flashes per second 1 1 1 1 1 1 l 1 I Signal is low gt on for 50ms off for 50ms very fast flash CCLCECELELCCCECEECECECEE CELL EEE CET Problem with GSM engine gt on for 100ms off for 500ms on for 100ms off for 500ms on for 500ms off for 500ms 2 short and 1 long flash a a e a a Setup is corrupt gt on for 50ms off for 100ms on for 50ms off for 100ms on for 50ms off for 1000ms 3 short flashes CRC CRC CC Eu Supply voltage below 9 5V RED LED GSM gt OFF GSM engine OFF gt on for 600ms off for 600ms 1 flash per second ry GSM engine not finding network gt on for 75ms off for 3000ms 1 flash every 3 seconds m GSM engine registered OK gt on for 600ms off for 600ms 1 flash per second sss GSM busy with a voice call Polygon Technologies All rights reserved Page 14 5 12 1 Status Request The Micro Commander even with a blank configuration has a built in test feature If the Micro Co
12. ELEMETRY CONTROLLER SA amp TA 2008 710 PWR IN AIRE GE puyang nn INPUT ONTPUT NEUTRAL This output can be used to control devices and appliances and is rated for 8A DC It may be used to control most types of electrical loads excluding AC motors above 500W Polygon Technologies All rights reserved Page 12 Here are some examples of things you CAN directly switch on and off using the output on the Micro Commander e Gate motors and any other motor less than 500W e Mains Lights energy savers incandescents halogens maximum 750W Here are some examples of things that you can NOT directly switch on and off using the output on the Micro Commander e Ovens Heaters kettles e Pumps and motors above 500W Please note Keep in mind that if required the above loads can easily be switched on and off using an externally connected relay or contactor The Micro Commander provides connections for an external rechargeable 12V battery Under normal circumstances the Micro Commander will trickle charge the battery at a current of about 60mA In the case of a power failure the Micro Commander then starts drawing power from the battery to continue operating In the case of a power failure the Micro Commander can continue operating from the external battery The unit can be configured to perform certain tasks like sending a warning SMS if the battery voltage falls below a certain point and can also perform
13. age 7 Screen 1 GSM Commander V7 06 Welcome to the GSM Commander V7 0641 Install program This program allows you to install GSM Commander V7 0641 on your hard drive it is strongly recommended that before proceeding you ensure that no other Windows programs are running If you do not wish to install GSM Commander V7 0641 click Exit now otherwise click Next to continue Screen 2 GSM Commander V7 06 Directory Choose an installation folder and click Next to continue GSM Commander V7 0641 s files will be installed in the following directory C Program Files x86 GSM Commander V7 0641 Disk space needed Available disk space Click Next to continue Screen 3 Confirmation You are now ready to install GSM Commander V7 0641 This program will install GSM Commander V7 0641 into C Program Files x86 GSM Commander V7 0641 Click Start to install GSM Commander V7 0641 Polygon Technologies All rights reserved It is recommended that you leave the install path at the default location Click Page 8 Screen 4 GSM Commander V7 06 Installing p gt PR nl A Installation is in progress File C GSM_Commander INI Installation has been completed successfully Click Installation completed GSM Commander V7 0641 has been successfully installed Select the following option if you want GSM Commander V7 0641 to be launched after exiting
14. als are connected to the input power supply of the Micro Commander and are provided to make it easy to connect dry contacts to the Micro Commander If the power supply is 14V the voltage at the and terminals will be slightly less at about 13 8V due to an internal series diode for reverse polarity protection Polygon Technologies All rights reserved Page 11 Here is a schematic of the input circuit used on the Micro Commander IN 470R 3 IN Opto Isolator Drawing power for external hardware from the power terminals on the input One should not attempt to draw more than 50 100mA in total from the power terminals at the inputs on the Micro Commander The Micro Commander itself provides 1 x 8A DC Relay outputs The output has the following 3 terminals Each of these inputs each have 3 terminals associated with them COM Common Terminal N C Normally Closed Terminal N O Normally Open Terminal When the output is off the COM and N C terminals will be internally connected to each other When the output is on the COM and N O terminals will be internally connected to each other Note that there are small LED indicators next to the output terminals that will show if the output is ON or OFF if the LED is on then the output is also on In the picture below the output is connected so that the lamp will light up when the output is on Model D Gz HWHWH GSMCOMMANDER COM MICRO COMMANDER PROGRAMMABLE T
15. be set to every 5 minutes ADMIN GPRSSETUP LOG10 GPRS logging interval will be set to every 10 minutes ADMIN GPRSSETUP LOG15 GPRS logging interval will be set to every 15 minutes ADMIN GPRSSETUP LOG30 GPRS logging interval will be set to every 30 minutes The GSM Commander will reply with a confirmation message This command can be sent from ANY number To reset the Micro Commander you must send RESET GSMC The Micro Commander will NOT reply with a confirmation message The Micro Commander is configured by defining a number of behaviour statements Each statement takes the form of an IF THEN pair You are thus able to select certain trigger conditions that will cause desired actions to be performed Any combination of IF and THEN parts can be assembled into complete statements using the configuration software The Micro Commander can accept up to 10 separate behaviour statements 8 1 1 IF a Message is Received A statement containing this IF condition will trigger on the arrival of a SMS message The user has a choice of the following four options e From Any number Containing Anything or a Specific Message e From Any number appearing in the list Containing Anything or a Specific Message From a Specific number in the list Containing Anything or a Specific Message Thus if the user chooses From Any number Containing Anything or a Specific Message then literally any SMS if not specified from any number wil
16. ble If the problem persists please follow this procedure to verify that the drivers are correctly installed Step 1 Connect USB Cable to Micro Commander ONLY USB and not the Power Press Windows key and Pause simultaneously on your computer keyboard This will bring up the System properties window as below SLR ea F Contro Panel H sr A ata ae View basic information about your computer WU Device Manager Windows edition Remote settings Windows 7 Ultimate p System protector Copyright 2009 Miurssufl Curpuidliun All tights reserved OP Advanced system settings System Raling A iin Jrocessor Intel R C2leron R CPL 3 209 amp 240G4z 240 GHz Installed memory RAM 200 GB System type 32 bit Operet iro System Den and Teuch Ne Pen gt Touch Input is available tor this Display Computer name domain and weregroup settings See also Compute aame Change settings Full cumpulet namie Computer description Action Center Windows Update Perfurnance Infuirnetion and i Workgrcur ss Polygon Technologies All rights reserved Page 33 Step 2 Select Device Manager This will open the device manager window as below Device Menage Fikes Actions Vicwro Help e9 m Hml E 4 a SherwirPC b JE Computer b Disk drives b Display adapters b DYP CR ROM crives b Oj Hurnan Interface Devices b tq DC ATA ATAPI controllers tf Infrared devices b Ke
17. ccaewacgrapeainseraseeeadareseads aE dresser E E E ES 10 Optically Isolated Digital Inputs seensssoseeesesossecssscssecesesseoseosesscosesecsecseesee 10 DUNDES S E E EE T A T E Nr Dao 12 Battery NDUT cee cea sinnir oi reee rE a EEEE E EEEo 13 status LEDS eosar oree EEr E OE O A SEE EE EET TE OEE EEE ERTE E EOE 14 Testing the Micro Commander e sesesesessssccsssossesoseeeserosesosecscessoscossoeseeseesseeo 15 Configuration Vid PC scsssscnccsnwscacseacsasnsanawecsesvaudesqneswhesnawuensouseetosepesghassessumesassen 15 Configuration Vid SMS vecaisccuctecnescacacceweboaesweesdsadeuedsequseseawauaeseasaaianennaastassaneasneadas 18 Set Administrator NAME Sri seance croco interdire 19 Clear Administrator NOMBEL sc osesccaceascandsesacescasesesancencondsiienuwenwensis onevecrwarsens eas 19 Check Administrator number ses 19 Check CA a na ame nds doit a ec ne en De ot 19 Add a Number to the Seine sermenesseesnmemersesni teseteeeilbeiteiti roses 19 Remove a Number from the St issethecse riens css msseshenepsanesentonrs teeseande 20 Phiabley Disable Statens as ann bescnens he ensuite odeur ere 20 Override GPRS SettingsS ssssseseessesressesroseeeseeroeroeseecsessosoessroreecsseseereeesesree 20 Reset GPRS RER eee aoe ee EEE EOE T ERNE Sa 20 Set GPRS logging SA ee ne cc or aout 21 Reset Micro COMMANCEF 545 2 uisssdustadenndahes sossgeat ncmssatressre rec sencencedieianesiedre 21 IF THEN Behaviour statement
18. containing this IF condition will trigger if the selected input changes according to specification The user can choose between the following seven options e Goes Active Trigger on rising edge Goes Inactive Trigger on falling edge Changes State Trigger on rising or falling edge Goes Active remaining Active for longer than Goes Inactive remaining Inactive for longer than Is Active Trigger on high level Is Inactive Trigger on low level Thus if the user chooses Goes Active then as soon as the specified input changes from inactive to active the statement will trigger The same applies to the remaining options provided their conditions are met The user is also able to specify a Lockout Time for this statement which is the time that after the statement has triggered it will not allowed to trigger again until this time has elapsed If the user selects a Lockout Time of zero the statement will only trigger once will trigger again when the trigger condition has changed and becomes true again with the last two options being an exception 8 1 4 IF Output This trigger condition is very similar to IF Input 8 1 13 as it monitors and output instead of an input 8 1 5 IF Logic Expression A statement containing this IF condition will trigger if the specified logic conditions are met This allows the user to specify interesting combinations like input 1 AND input 2 must be ac
19. cted to the BATT terminals on the Micro Commander The Micro Commander will operate from the battery in the case of a power failure 8 1 7 IF Power Restored This trigger condition is the inverse of 8 1 6 8 1 8 IF Battery Voltage lt X A statement containing this IF condition will trigger if the battery voltage goes below a preset threshold level The user is also able to specify a Hold Time for this statement which is the time that the trigger condition must continuously be true before it will be allowed to trigger The user is able to specify a Lockout Time for this statement which is the time that after the statement has triggered it will not allowed to trigger again until this time has elapsed If the user selects a Lockout Time of zero the statement will only trigger once will trigger again when the voltage goes above and below X Please Note To use this option the user needs to have a 12V battery connected to the BATT terminals on the Micro Commander The Micro Commander will operate from the battery in the case of a power failure While the Micro Commander is powered the battery will be trickle charged by the Micro Commander It is therefore important to note that the battery level will only be checked while a power failure is in progress 8 1 9 IF Prepaid Airtime lt X A statement containing this IF condition will trigger if the prepaid airtime goes below a preset threshol
20. d level The user is able to specify a Lockout Time for this statement which is the time that after the statement has triggered it will not allowed to trigger again until this time has elapsed The Micro Commander will check the prepaid airtime balance from time to time and the statement will trigger if the balance is below the selected threshold Important Under the Settings Tab in the configuration software you need to have DO NOT Check Airtime Unchecked which is found in Edit Settings Also make sure that the correct network is selected 8 1 10 IF time elapsed gt X A statement containing this IF condition will trigger every X seconds or minutes Polygon Technologies All rights reserved Page 24 8 1 11 IF Statement X has not triggered in a certain period A statement containing this IF condition will trigger if the referred to statement has triggered in a specified period Thus this type of statement actually monitors the triggering behaviour of another statement 8 1 12 IF Date Time X A statement containing this IF condition will trigger on a specific time every day within a specified range of dates or on every selected day of the week The user can choose between the following four options 1 Everyday 2 Day of Week 3 Once per month 4 Specific Date Range 8 1 13 IF Powerup or Reset A statement containing this IF condition will trigger as soon as the unit has f
21. d post the voucher number along to the network Polygon Technologies All rights reserved Page 29 Step 1 Download the setup exe executable file from our website http www gsmcommander com Step 2 Run the executable file See 5 6 Step 3 Connect Micro Commander to PC via the supplied USB cable Step 4 Connect power to the Micro Commander Step 5 Run the Utility Start gt All Programs gt GSM Commander V7 0101 gt Update Firmware The SmartSetup software will also automatically detect upon startup if the firmware currently loaded on the Micro Commander unit does not match it s current version It will then prompt you to run the update firmware utility Screen 1 The loader utility will show this screen when started Detecting hardware state Screen 2 The loader utility will now show this screen which means the firmware is being updated The green LED labeled STATUS on the Micro Commander will start flashing On completion the loader utility will close and the unit will start up automatically or if you so wish you can disconnect the power Polygon Technologies All rights reserved Page 30 In this example we discuss the use of periodic messages to ensure that your Micro Commander produces a billable event on the network on a regular basis If you use a prepaid SIM card the network will de activate your SIM card if it has not been used for some time See Section 6 4 W
22. e Time Status of Behaviour Statements VV VV V V VV WV Inputs Outputs Status The Micro Commander provides functionality to provide some configuration changes to be done via SMS message from the administrator number only Note that the unit cannot be setup by SMS only A PC is still required to perform the initial setup Thereafter some simple changes to the setup may be done using SMS messages Please note The Configuration SMS is NOT case sensitive The following operations can be performed via SMS message gt Set Administrator number gt Clear Administrator number gt Check Administrator number gt Check Airtime gt Add a number to the list gt Remove a number from the list gt Enable Disable statements gt Configure GPRS settings gt Reset GPRS gt Set GPRS logging interval gt Reset Micro Commander Polygon Technologies All rights reserved Page 18 This command can ONLY be sent from the administrator number if one exists otherwise it can be sent from any number ADMIN SETADM 0831234567 This will store 0831234567 as the new administrator number The Micro Commander will reply with a confirmation message This command can ONLY be sent from the administrator number ADMIN CLRADM This will remove the current administrator number The Micro Commander will reply with a confirmation message This command can be sent from ANY number and is useful to determine which number is t
23. e Note The Micro Commander will lose its time if power is removed and no battery backup is used Upon power up if any statement has a time constraint enabled the Micro Commander will automatically send a message to the first number in the list requesting a SETTIME reply so that it can set its time This message will be sent a maximum of 3 times The Micro Commander will not allow any time constrained statement to trigger if the time has not yet been set If using a prepaid SIM card it is recommended that prepaid airtime be topped up via an ATM or via your bank s Internet banking portal If your network or bank does not support this you can purchase a normal airtime voucher and remotely send the voucher number to the Micro Commander which will in turn send the voucher number to the network to top up the airtime Your airtime top up voucher is typically a long number and when using this voucher number with a normal cellphone you typically need to frame this number by some preceding and appending text For example with MTN in South Africa you need to send 141 0000000000000 where the 141 is network dependent and the 0000000000000 is the voucher number This detail is typically provided on the voucher slip To send a voucher to the Micro Commander you simply send it an SMS of the form SENDUSD 141 000000000000 from any number where 000000000000 is the voucher number The Micro Commander will receive this an
24. e anew number The user also has the option to insert special characters into the string to create more complex messages See section 10 8 2 3 THEN Place Voice Call A statement containing this Action will place a voice call to each of up to 6 selected recipients The user is able to specify the time to ring the number of calls to make as well as the time between calls The recipient number can be defined in one of the following five ways e Not Used e Last voice call number e Last sms number e A predefined number from the numbers list e Anew number Please Note If a call is answered then hung up subsequent calls for this event will be cancelled 8 2 4 THEN Enable Disable Statements A statement containing this Action will enable or disable up to a maximum of 8 selected behaviour statements such that it will be allowed to trigger if it is enabled and not be allowed to trigger if it is disabled 8 2 5 THEN Enable Disable ALL SMS Sending A statement containing this Action will enable or disable ALL SMSes meaning that if it is enabled it will allow the sending of any SMS messages and if it is disabled it will inhibit the sending of any SMS messages 8 2 6 THEN Set Multiple Outputs to Pattern A statement containing this Action will change the status of multiple outputs to a certain state 8 2 7 THEN Reset device A statement containing this Action will reset the Micro Commander Polygon
25. e is topped up See your network s documentation on how to purchase and load airtime The SIM card is fitted into the back of the unit as indicated by the legend on the enclosure The SIM card will click into place and is removed simply by pressing against it The card will pop out with a click sound ready to be completely removed Polygon Technologies All rights reserved Page 6 Before you install your SIM Card e Install the SIM card into a normal cellular phone e Verify that there is no SIM PIN enabled The phone must not ask for a PIN when switched on with this SIM card inside If the phone does request a PIN you need to enter the correct pin so that the phone can start and then disable the SIM Card PIN See your cellphone documentation on how this can be done e Verify that you are able to send an SMS message The SIM card will now work with the Micro Commander Please Note If you are using a prepaid SIM card be aware that if the SIM card has not produced a billable event on the network for a long period of time typically 3 months the card will be de activated by the network and the SIM card then becomes useless It is strongly recommended that you configure the Micro Commander to send you an SMS every now and then once or twice a week so that your SIM card remains active on the network The Micro Commander can ONLY check the airtime of a PREPAID SIM card The Micro Commander is supplied with a basic antenna ope
26. e will create two behaviour statements The first will send a free of charge please call me message every day to give you a confirmation that the unit is up and running The second will send a Status SMS to your cellphone once a week to ensure that the SIM card remains active on the network The status message also gives you the total airtime remaining Configuration Using the setup software we create a behaviour statement that will read as follows IF Date Time is 12 00 THEN Send Please call me to 27821231234 A second behaviour statement is created that reads IF Date Time is 8 00 On every Monday THEN Send Status Message to 27821231234 The Micro Commander could also be configured to only execute an action during a specific date range A time constraint could also be assigned to any trigger condition a In this example we need to monitor an alarm system and in the case of an alarm the Micro Commander must make a voice call and send a message to one or more numbers Hardware We connect the alarm output 12V signal that drives the siren to one of our inputs as described in section 5 8 The positive wire from the alarm panel is connected to the IN terminal and the negative wire is connected to IN Configuration Using the setup software we create a behaviour statement that will read as follows IF Input 1 Goes Active THEN Place voice call to 27821231234 We create a second behaviour statement
27. essage one for active and one for inactive regarding the status of the selected input or output either via SMS to each of up to 6 selected recipients gt General Status it will send a general status message either via SMS to each of up to 6 selected recipients containing the following information date amp time signal strength firmware version serial number airtime remaining status of mains power gt Input Status it will send a message either via SMS to each of up to 6 selected recipients containing the status of the input gt Output Status it will send a message either via SMS to each of up to 6 selected recipients containing the status of the output gt Please Call Me it will send a Please Call Me message via SMS to each of up to 6 selected recipients Polygon Technologies All rights reserved Page 26 Please note that the Please Call Me will only work if the correct network is selected in the Settings tab of the configuration software gt Log Status to Server it will send a status message via GPRS to our server to update the status of the Micro Commander on the AirDrive platform Log onto Airdrive to find out more The recipient number can be defined in one of the following six ways e Not Used e Last voice call number e Last sms number e Reply to originating number only available with IF conditions 8 1 1 and 8 1 2 e a predefined number from the numbers list
28. g m al gt Z g fe i ei Ko F a 2i gt 2igx E LL 5 v a MI oe oe oe oe 2 x A a 2 gl go GS GC m oO osiy z GO ONE a lt lt lt OC FAS slaa A z GC0101 1 1 1 1 10 128 16 127 YES 0 0 YES NO NO Single GC0321 2 2 12 12 32 250 64 127 YES 2 1 YES NO NO Single GC0641 2 2 22 22 64 512 128 127 YES 2 1 YES YES YES Single GC1281 2 32 32 128 512 128 127 YES 2 1 YES YES YES Dual Matrix Feature Descriptions Model The code used to define between the various units functionality and capabilities Onboard Inputs The number of inputs provided on the base unit itself Onboard Outputs The number of outputs provided on the base unit itself Expandable Inputs Outputs The maximum total number of Inputs Outputs that can be expanded to by fitting expansion units Max Number of Statements A measure of the amount of complexity that can be programmed into the unit Each statement is of the form IF lt ABC happens gt THEN lt do something gt such as IF Input 1 goes Active THEN send Generator Tripped to 0831231234 Max Number of Phone Numbers The maximum total number of phone numbers that can be programmed into the unit Max Number of The maximum total number of messages that can be programmed into the unit Messages Max Number of The maximum total number of behaviour statements that can be programmed into the S
29. he correct administrator number ADMIN The Micro Commander will reply with the administrator number in the reply message This command can be sent from ANY number and is useful to check the amount of airtime remaining on the unit To check airtime you must send ATCHECK The Micro Commander will reply with a message detailing the current airtime This command can only be sent from the administrator number To add a number to the list the administrator must send ADMIN ADDN 0831234567 The Micro Commander will reply with a confirmation message Please Note The value predefined by the user via the software under the Numbers Tab as illustrated below will determine how many numbers are able to be added and removed by means of SMS Set number of numbers to reserve for adding removing per sms here g al 1 Polygon Technologies All rights reserved Page 19 This command can only be sent from the administrator number To remove a number 27831234567 from the list the administrator must send ADMIN REMN 0831234567 The Micro Commander will reply with a confirmation message This command can only be sent from the administrator number To enable or disable a specific statement in the setup on the Micro Commander the administrator must send ADMIN STATEMENT 8 ON or ADMIN STATEMENT 8 OFF This will either enable ON or disable OFF statement 8 respectively The Micro Commander will reply with a
30. ice Call to 27821121323 St3 IF Input 1 Goes inactive THEN send alarm off via SMS to 27833341234 Polygon Technologies All rights reserved Page 32 The above 3 statements detail two actions to trigger in the event that the input goes active One is an SMS message to the remote unit and another is a voice call to a cellphone In the above statements 27833341234 is the number of the Micro Commander at the remote location Remote Micro Commander hardware We use a second Micro Commander unit at the remote location Here we connect the warning light to output 1 of the Micro Commander so that if the relay is activated the warning light will turn on exactly as described in section 5 9 Remote Micro Commander configuration The configuration of the remote unit will be similar to example 2 control an appliance Using the setup software we create the following behaviour statements IF Message is received containing alarm on from any listed number THEN Activate Output 1 IF Message is received containing alarm off from any listed number THEN Deactivate Output 1 This error can have several causes Cause 1 Micro Commander not powered properly Cause 2 Micro Commander not connected via USB Cause 3 Micro Commander USB drivers not installed It is a good idea to disconnect all cables from the Micro Commander and then reconnecting everything power and USB ca
31. inished booting up 8 1 14 IF GSM Signal Strength A statement containing this IF condition will trigger as soon as GSM signal strength meets the specified requirements The user can choose between the following two options Above X Below X Thus if the user chooses Below X then as soon as the GSM signal strength goes below the specified threshold the statement will trigger The same applies to the remaining options provided their conditions are met The same applies to the other option provided it s condition is met The user is able to specify a Lockout Time for this statement which is the time that after the statement has triggered it will not allowed to trigger again until this time has elapsed If the user selects a Lockout Time of zero and the Below X option the statement will only trigger once will trigger again when the signal goes above and below X 8 1 15 IF Statement X Triggers A statement containing this IF condition will trigger if the referred to statement has triggered Thus this type of statement actually monitors the triggering behaviour of another statement Polygon Technologies All rights reserved Page 25 8 2 1 THEN Change Output E A statement containing this Action will change the selected output according to specified actions The user can choose between the following five actions e Activate for a time e Activate for a
32. l cause the statement to trigger This will include SMS messages from private withheld numbers Note the word containing in this condition If you have a trigger condition like this one IF a Message is Received From Any number containing Apple is received from XYZ then lt ACTION gt The statement will trigger on arrival of any of the following messages Apple LE APPLE The Red apple You will notice that trigger text strings are NOT case sensitive Both Apple and APPLE will work fine It is also important to note that you can trigger multiple statements with different trigger texts in the same SMS For example if you have the following two statements IF a Message is Received From Any number containing Apple is received from XYZ then lt ACTION gt IF a Message is Received From Any number containing eat is received from XYZ then lt ACTION gt These statements will both be triggered if I eat an Apple is received via SMS Please Note If From Any number appearing in the list Containing Anything or a Specific Message or From a Specific number in the list Containing Anything or a Specific Message are selected and an SMS arrives from a private number the statement will not trigger 8 1 2 IF Voice Call is Received Call Options Hang up or Stay on A statement containing this IF condition will trigger if someone actually places a call to the Micro Commander nu
33. mber The user has the option to select which group of senders originators are able to cause the the statement to trigger The user can choose between the following three options e From Any number e From Any number in the list From one specific number Thus if the user chooses From any number then literally any call from any number will cause the statement to trigger This will include calls from private numbers The same applies to the remaining options provided their conditions are met Polygon Technologies All rights reserved Page 22 Please Note If anyone of the other two options are selected and a voice call is made from a private number the statement will not trigger As soon as the statement triggers the Micro Commander will hang up if option is selected This is of importance because it allows the user to have some sort of feedback that the Micro Commander has in fact responded to the call Since the Micro Commander answers the call for a split second it is cost effective This type of statement option is very handy to use for tasks of high importance for instance the arming of an alarm system If the Stay on call option is selected the Micro Commander will hold the call until the caller ends the call Please Note If the Stay On call option is selected it should be defined in the last IF Voice Call is Received behaviour statement if any exist 8 1 3 IF Input A statement
34. mmander receives TEST GSMC as an SMS message it will reply to the number that sent the message with the following text DT 01 01 2013 12 00 00 lt Indicates current date amp time of the Micro Commander Sig 68 lt Indicates the received signal strength Airt 35 lt Indicates the amount of airtime remaining FW 7 14 lt Indicates the firmware version SN 140101 30225 lt Indicates the serial number PWR 0n lt Indicates status of mains power Batt 13 2V lt Indicates voltage of battery if connected IN1 0 lt Indicates status of inputs 1 and 2 0 active 1 inactive OUT1 0 lt Indicates status of outputs1 and 2 0 active 1 inactive Please Note The airtime remaining will be displayed as Airt if airtime checking has been disabled or the incorrect network operator has been chosen in the current setup The following is required to configure the Micro Commander A PC running Windows XP Vista Windows 7 Windows 8 Setup utility installed on the PC Available on the CD supplied with the product USB cable Provided Power supply See 5 2 Antenna See 5 5 v Vv NN V WV SIM card s See 5 4 Please note The Micro Commander will eventually startup if no SIM card is inserted but there would be no GSM functionality which means none of the GSM features will work Polygon Technologies All rights reserved Page 15 Follow these steps Step 1 Insert SIM card into unit Step 2 C
35. om any number in a list of accepted numbers This is an ideal method to control a communal gate in a complex Hardware Many gate openers require a pulse to open and second pulse to close We will use the output of the Micro Commander to supply this pulse at the position where the open close switch is normally connected to the opener Configuration Using the setup software we create a behaviour statement that will read as follows IF a Voice Call is received from any listed number THEN Activate Output 1 for 1 Sec Pause for 20 Sec Activate again for 1 Sec In a few instances it may be necessary to transmit the status of a contact to a remote point Let us use an alarm as example If the alarm at your home sounds you may want a warning light to switch on in a remote location and a voice call to be placed to a specified number For this example we will use two Micro Commander units one at the local alarm system and another at the remote location Local Micro Commander Hardware We connect the alarm output 12V signal that drives the siren to one of our inputs as described in section 5 8 The positive wire from the alarm panel is connected to the IN terminal and the negative wire is connected to IN Local Micro Commander Configuration Using the setup software we create the following behaviour statements St1 IF Input Goes Active THEN send alarm on via SMS to 27833341234 St2 IF Input 1 Goes Active THEN Place Vo
36. ommander with the messages they wish the Micro Commander to respond to and respond with either via SMS serial port or GPRS This tab allows the user to program the Micro Commander with a number of trigger conditions See chapter 8 This tab allows the user to configure the following gt Network Service and GPRS Settings Enable Disable Simcard Pin Enable Disable Periodic Automatic GSM Reset Show Debug Comms Manually send an SMS via the Micro Commander Write Recipient and 10 Names to device Vv Vv Y Y V V Change application size pixel dimensions of software This tab allows the user to rename the input and output to something that means a little more Please Note These IO Name changes will be stored in the setup that is saved to file but will ONLY be stored in the setup that is saved to the Micro Commander if enabled under Settings Tab This tab allows the user to password protect tabs from being accessed as well as the option to save a new setup to the Micro Commander This feature comes in handy when an installer doesn t want the end user to be able to make changes under certain tabs _ Polygon Technologies All rights reserved This tab allows the user to monitor the status of Micro Commander while connected to PC with regards to Active SIM GSM Status GPRS Status Power Status Current Battery Voltage Signal Strength Airtime Balance Available provided network settings are correct Dat
37. onnect Micro Commander to PC via the supplied USB cable Step 3 Connect power to the Micro Commander Step 4 Run the Utility Start gt All Programs gt GSM Commander V7 0101 gt Configure GSM Commander Open setup from file Read setup from device Just open to main screen Launch older version The software will show this screen when started Here you can select whether you would prefer opening an existing setup from a file on your PC retrieve the setup currently on the Micro Commander just open to the main screen or launch an older version of the software The SmartSetup utility software has been designed to make the configuration process of the Micro Commander as easy and user friendly as possibly With this in mind the software has been divided into the following tabs gt VV V Y V WV Numbers Messages Behaviour Statements Settings 10 Names Lock Setup Status Polygon Technologies All rights reserved Page 16 This tab allows the user to program the Micro Commander with the numbers they wish the Micro Commander to communicate with and listen to The FIRST number in the list is defined as the ADMINISTRATOR number Only the Administrator may send configuration SMS messages to the device Please Note The user should adjust the sliding bar at the bottom of the screen to reserve space for numbers to be added removed via SMS See sec 7 6 This tab allows the user to program the Micro C
38. ons e Output Voltage 14V nominal e Output Current 0 5A e Polarity A suitable power supply is supplied with the retail product In industrial applications it is advised that the Micro Commander be installed into its own metal housing and be powered from a separate power supply with a DC Filter As opposed to sharing one with other equipment Please Note While the Micro Commander has fairly rugged internal power supply circuitry no special provision for lightning protection is made If the Micro Commander is used in an area that is prone to thunderstorms it is advisable to use a commercially available lightning suppressor The same applies to inputs or outputs that are connected to wires longer than 2 or 3 meters The guarantee does not cover damage resulting from lightning strikes The Micro Commander provides a USB port that connects to a PC using the supplied USB cable This allows the PC to configure the unit The Micro Commander accepts a standard GSM SIM card from any network The SIM card may be prepaid or on contract If the SIM Card is purchased as part of a prepaid plan ensure than the card is loaded with sufficient airtime WARNING DO NOT Insert or remove the SIM card while the Micro Commander is powered Note that airtime will decrease with every SMS that is sent from the unit The unit can automatically detect if the airtime is running low It is user s responsibility to make sure than the airtim
39. period it will be repaired or replaced at the sole discretion of Polygon Technologies under the following conditions A The unit must not have been opened or otherwise tampered with If the enclosure of any unit has been opened at all the guarantee will be null and void B The guarantee does not cover damage resulting from excessive input voltages lightning power surges or water ingress A decision about issues A and B will be at the sole discretion of Polygon Technologies This guarantee does not provide for shipping costs This will be for the account of the user under all circumstances Herein the Company will mean Polygon Technologies CC its directors members employees and agents Much effort has been made to ensure the contents of this manual are complete and without errors Nonetheless the Company cannot be held liable for any damages directly or indirectly resulting from any errors in this manual The Company will under no circumstances be held liable for any injuries death or damages that result from the use of this product irrespective of whether such injuries death or damages resulted from a faulty product or negligence of any kind on the part of the Company All Information and images in this manual are proprietary to Polygon Technologies CC The manual as a whole may be distributed and copied freely but no partial content may be used copied or distributed in any way No part of the product including the hardware
40. rating in the GSM 900MHZ and 1800MHz frequency bands Screw the antenna to its connector on the unit only finger tight Verify using a cellphone that there is sufficient signal at the proposed installation site On a phone with a 4 or 5 bar signal strength indicator you should have at least 1 2 bars of signal If the signal is too weak the Micro Commander may have trouble sending or receiving SMS messages In these cases try and find a better location or order one of our special antennas If you are outside South Africa you may require a different antenna The other frequency bands are gt GSM 850MHz gt PCS 1900MHz Your network will be able to tell you which frequency band s are in use Contact your local electronics supplier about antennas that operate in the 850MHz or 1900MHz bands Contact Polygon Technologies with your request for a special antenna The latest software is supplied on a CD with the product and is also available to download from our website for free at http www gsmcommander com The setup program will start automatically or if the autorun feature is not enabled on your PC you may run the setup exe executable file on the CD to start the setup process The software has been tested to work on Windows XP Windows Vista Win7 Win8 The setup process for Windows 7 has been documented here but the process is similar in the other versions of Windows Polygon Technologies All rights reserved P
41. s sessecsecsecsecsececoecceesececseseoececoesececseseceseceeseceo 22 S pporfted IF CORAITIONS seu sannessss era cscmssumescannenecersenttatessesepm henenrs avenant 22 Supported THEN ACTIONS 6 dessiner EEEE EEUE EEEE EE EN T RTE ai 26 Multiple Actions to a Single IF Condition shesssasesssisessesesseniedsiiosiastesss 28 Message Parameter S iicsadiiicascusidnanwasiaasascaaavansaededasd bandascaunesaaaddibanounumbasansdaasas ia 28 Timed OPSFAliOMs vs dis cccscnsssisvacaccscacdsiewadauewesstwcasausessseseasumebesusnessesstencwevsuseansenees 29 Prepaid Airtime voucher FORAGING sts ini ssissenonsussesednonanesaedientsss aies 29 Firmware Updates seau oiasie sasabide pasleiaauus a E een aaa EEE 30 Application Examples sssscs cia siachavasesceasinewaseiesssoedsieensssiuteseedeacwatenesedkeassaraeneus 31 TrOUDIES OO NS ins sscesnsensnnesasataseM eat sdeien cena Diese 33 GUAFANEBR sss nus esssressiscrenreremessensmessannereiescusdsiandienieneelsennennedmeneistiotens 35 Important Notice Disclaimer eines cunessnisensetoniosaen apieencsneendrescvessse 35 Manufacturer Contact Details ssisssssdssesaanesssesinacs nmaenssenesd nneossonauns 36 Polygon Technologies All rights reserved Page 2 a 21 8 amp tS T a S aje Rl l lg v I e 8 6 22 82 588 S B 3 s Z 8 a re 5 on Ool g D D ae il ie IS IEEE SG RE ai E tw S x 2 a la K 5 3 on o o wi o gt 6 D 2 5 T
42. tasks in the case of a power failure Like sending an SMS and switching on emergency lighting In cases where the Micro Commander is used in conjunction with a large system with its own battery such as UPS systems the battery terminals of the Micro Commander can be safely connected to the large 12V battery and the Micro Commander can then monitor the battery voltage for you only while power is NOT supplied to the power input connector Also in cases where the user may want to connect other hardware directly to the battery be aware that this will probably drain the battery since the charging current from the Micro Commander is so low Other hardware should rather be connected to the power terminals provided at the inputs See section 5 8 for more information on this Internal to the Micro Commander the Battery terminal is wired with a 47ohm resistor between the Batt terminal and the positive power supplied to the Micro Commander There is a diode in parallel with this resistor cathode facing to the battery to allow the Micro Commander to draw power from the battery under power fail conditions A resettable fuse has now also been added to give the Battery terminal added protection against voltage spikes and short circuits Suitable batteries are available from Polygon Technologies Polygon Technologies All rights reserved Page 13 The Micro Commander has 2 LEDs to show the current status of the Micro Commander The red LE
43. tatements unit GPRS Enabled If yes the unit is able to be registered onto the AirDrive Platform which can allow it to log its status log it s events have remote config and remote output control via GPRS Temp Probes Supported The number of temperature probes the base unit can accept 0 10v Analog Inputs The number of analog Inputs available Battery Power Monitor The ability to detect power failures and monitor a connected battery Extended Analogs Allows the possibility to connect an Analog Expansion unit which will provide an additional 8 analog inputs DTMF Decoder If YES the unit is able to recognize and respond to key presses on a remote phone during a voice call SIM Card Slots If Single the unit has only a single SIMcard slot If the SIMcard in that slot becomes faulty or the associated network goes down the unit loses communication ability If Dual the unit can switch over to a secondary SIMcard if it detects problems on the primary SIMcard thus greatly enhancing reliability Only able to view the current status of the unit via Airdrive Polygon Technologies All rights reserved Page 3 Weight 100gram Dimensions 125 7 x 71 9 x 26mm Power Supply 10 14V DC via DC Jack Power Consumption 2 5W Current Consumption 50mA at idle no inputs or outputs active Operating Temperature 10 C to 60 C Storage Temperature 20
44. that will read as follows IF Input 1 Goes Active THEN Send Alarm triggered via SMS to 27821231234 27843214321 The first statement will cause a voice call to be placed to 27821231234 in the event of an alarm The second statement will cause a notification SMS to be sent to both 27821231234 and 27843214321 This is an example of how the Micro Commander can have multiple actions triggered by a single event in this case an input becoming active Note that the voice call will not say anything when the call is answered One will typically use Caller ID to identify the Micro Commander number and this will be enough to let you know that there is something wrong at home Polygon Technologies All rights reserved Page 31 In this example we need to switch a 220V light bulb on or off via a suitable SMS message from a specific number listed on the Micro Commander Hardware We connect light bulb to a 220V power source via the output 1 contact on the Micro Commander exactly as described in section 5 9 Configuration Using the setup software we create a behaviour statement that will read as follows IF Message is received containing Lights on from 0821231234 THEN Activate Output 1 We create a second behaviour statement that will read as follows IF Message is received containing Lights off from 0821231234 THEN Deactivate Output 1 In this example we need to open a gate in response to a missed call fr
45. tive before action is taken The user is also able to specify a Lockout Time for this statement which is the time that after the statement has triggered it will not allowed to trigger again until this time has elapsed The logic options available includes AND ALL the selected signals become active TRUE or ANY of the selected signals become inactive FALSE OR ANY of the selected signals become active TRUE or ALL of the selected signals become inactive FALSE XOR ANY UNEVEN number of the selected signals become active TRUE or ANY EVEN number of the selected signals become active FALSE Polygon Technologies All rights reserved Page 23 8 1 6 IF Power Failure Detected A statement containing this IF condition will trigger if the power supplies to the 2 1mm DC jack power connector on the Micro Commander is interrupted The user is able to specify a Lockout Time for this statement which is the time that after the statement has triggered it will not allowed to trigger again until this time has elapsed The user is also able to specify a Hold Time for this statement which is the time that the trigger condition must continuously be true before it will be allowed to trigger If the user selects a Lockout Time of zero the statement will only trigger once will trigger again when the power is restored and fails again Please Note To use this option the user needs to have a 12V battery conne
46. yboards p f Mice and other acirting devices b Le Monitors MP Network adapters b SF Ports COM amp LPT gt 2 Processors b K Seunc vides and game controllers b lll System devices p Universal Seticl Bus curtrellers Double Click on Universal Serial Bus USB controllers In the list of USB controllers you should see an item called GSMCommander If this item is not present the drivers are not installed correctly To install your drivers go to C Program Files GSM Commander V7 0101 drivers drv_install and run GSMC_USBXpressinstaller exe or run Reinstall drivers Start gt All Programs gt GSM Commander V7 0101 gt Reinstall drivers This will reinstall your drivers This is a problem state and may be caused by a supply voltage that is too low The supply must be in the range 10 14V If this problem persists the Micro Commander is faulty Cause 1 Airtime problem The airtime on your SIM card may be depleted or the SIM card may have been de activated by the network Refer to Section 5 4 SIM Card Cause 2 Reception problem You may have bad reception in your area preventing the unit from connecting to the network Please check using a regular cellular phone that there shows 1 2 bars of signal right next to the Micro Commander Refer to Section 5 5 Antenna Cause 3 Bad configuration You may have configured the unit incorrectly Please send a status request message to the unit and see
Download Pdf Manuals
Related Search