User Manual - Comkit Online
Contents
1. TO MAKE SURE MANUALS AND WARRANTY CARDS ARE THERE ALSO GO THROUGH MANUAL WITH CUSTOMER E G LIGHTING CLEANING WASH HOSES SHOULD NEVER BE USED ON THE APPLIANCE USE OF HOSES WILL VOID WARRANTY IMO83B1 p7 Goldstein 4 OPERATING INSTRUCTIONS GAS BURNERS TK 24 1 BURNER TK 30 1 BURNER TK 36 1 BURNER TK 45 2 BURNERS The Burners are adjusted as described on Page 9 Cooking is generally started towards the middle of the burner and then moved to the area which is not directly over the burner and can be held there for final finishing IM083B1 p8 Goldstein 5 PILOT amp BURNER OPERATION A 9 SPARKER TO LIGHT PILOT A OFF IGNITION POSITION LIGHT PILOT If flame failure hold for 10 seconds to establish pilot flame C TURN TO FULL ON MAX GAS FLOW FURTHER ADJUSTMENT BETWEEN POSITIONS C amp D D TURN TO MINIMUM FLOW MIN GAS FLOW TO MAINTAIN FLAME Adjustable to suit type of gas used as precise and accurate TO OPERATE Push and turn knob to position light pilot burner and hold in for10 seconds to establish Pilot flame release pilot burner should remain alight and turn to position C for full flow of gas for minimum gas flow turn to position D Adjustable to suit type of gas used Further adjustment of gas flow between position C amp D IMO83B1 p9 Goldstein 6 TECHNICAL INSTRUCTIONS Cont d PILOTS Polidoro 509 Gas to pilot is controlled thro2. tel 319VL MYANIdIL sl EUVINONY 2 SORWW JIOHM oN OIC s3 SOFE WEEK 0915103985 ASWAYSHLO ayoads Ag JNIWONINY ON SSFINN SNOISN3WIA NO SSONVHSTOL 397937 _ 60400 LL 10000483 N Bo LZATANYIN 0003929 0900 11 20900859 20900 11 Ca 0100 95 IMO83B1 p13 Goldstein MODEL MODELS TK 30 TK 36 TK 45 10 5 AG fos 12 4 1 8 9 1 J 2 3 Wes 9 N f nr 0 6 6 X we Ecke D IM083B1 p14 10 SPARE PARTS Goldstein ITEM No CODE e MKNPLM21 ESP00003 ESPLO650 GCKGROO1 GIJGP275 GIJGP185 GIJBT150 GIJBT105 GIJBT130 GIJBT210 GTC00450 GPIB0002 GPIC0002 10 GBN00005 10 GBNCWOOO 11 TT 00P03 12 GIJ00022 12 GIJ00032 OONO NENG 083 1 15 MODELS TK 30 TK 36 TK 45 DESCRIPTION KNOB GASCOCK GCKPF001 GCKGR001 PF BOIL SPARKER PIEZO C W SPRING WASHER NUT LEAD H T 650mm FOR SPARKER GRIDDLE GASCOCK RBA GPG PF WITH F F DIVICE INJECTOR N G 2 75mm NEW 32 DRILL INJECTOR 0 L P 1 85mm NEW 49 DRILL INJECTOR INNER 1 5mm N G OLD INJECTOR INNER 1 05mm L P OLD INJECTOR OUTER 1 30mm L P OLD INJECTOR OUTER 2 10mm N G OLD THERMOCOUPLE L 450 TOP BURNER BODY PILOT POLIDO PF PFC OVEN PFG CHD ELECTRODE CERAMIC GPIB0002 509F BURNER NEW BURNER
3. OLD GREASE CAN ASSEMBLY PILOT SPUD 22 L P G PILOT SPUD 32 N G Goldstein Installation must be carried out according to local regulations by qualified trade persons Isolating switch es shut off valves etc must be within easy reach of the machine for future service and maintenance requirements If in doubt call GOLDSTEIN ESWOOD or their representative for further information No responsibility will be accepted for defects or damages by improper installation for changes to the product not authorised by GOLDSTEIN ESWOOD or for operation outside the technical specifications GOLDSTEIN ESWOOD warrants their products to be free from defects in material and workmanship under normal use and service This does not include normal wear and tear of parts GOLDSTEIN ESWOOD will repair or replace any parts which in GOLDSTEIN ESWOOD s sole judgement are defective in material or workmanship in accordance with the warranty offered This undertaking covers the provision of labour and parts for 12 months from the date of delivery to the purchaser This undertaking applies only to state capitals Remote areas are not covered by this commitment and special enquiries should be made Note Travel time not covered by warranty To the maximum extent permitted by law any liability on Goldstein Eswood s part or on the part of its servants or agents for loss or damage of any kind whatsoever in connection with the products including liabi
4. T TO ENSURE THERE ARE NO GAS LEAKING HAZARDS Adequate ventilation must be provided by a hood with vent and exhaust fan Never make a direct connection between the unit and vent flue Check there is sufficient room between doors and other units to allow equipment to be moved into position Check the data plate to ensure that the appliance is suitable for the gas supply to which it is to be connected and for information relative to gas input Etc Follow these instructions carefully 1 Set unit in correct position ENSURE THERE IS A MIN 25mm REAR WALL CLEARANCE FROM COMBUSTIBLE MATERIALS AND THAT THE UNIT IS PLACED ON A FIRE PROOF BASE and adjust feet using a spirit level checking from back to front and side to side 2 Have a licensed gas fitter or our local gas company connect the appliance to the mains pressure supply NOTE The appliance must be installed by an authorised person and in accordance with the regulations of the local Gas Authority AS5601 AG601 and any other authority having jurisdiction The appliance has been tested and preset before leaving our factory but small adjustments may be necessary to suit local conditions Correct operation of the appliance must be tested as part of the installation procedure The governor supplied must be installed on the gas inlet to the appliance This is supplied as a loose item Licensed Gasfitter should make connection to main gas line Install a manual shut off valve in gas line to th
5. TEPPANYAKI PROUDLY AUSTRALIAN MADE INSTALLATION PROCEDURE USER MANUAL SERVICE INSTRUCTION MODELS TK 24 TK 30 TK 36 TK 45 Goldstein ESTABLISHED 1911 The Cooking Equipment Professionals www goldsteineswood com au Goldstein TABLE OF CONTENTS Keel 1 INTRODUCTION Page 3 2 INSTALLATION Page 4 amp 5 3 COMMISSIONING Page6 amp 7 4 OPERATING INSTRUCTIONS Page 8 5 PILOT amp BURNER OPERATION Page 9 6 TECHNICAL INSTRUCTIONS Page 10 7 TECHNICAL DATA Page 11 8 CLEANING INSTRUCTIONS Page 12 9 TEPPANYAKI TABLE Page 13 10 DRAWINGS Page 14 11 SPARE PARTS DRAWINGS Page 15 12 WARRANTY Page 16 13 BRANCHES Page 17 IMO83B1 p2 Goldstein int n UI Congratulations for purchasing your Goldstein commercial cooking appliance J Goldstein amp Co is a wholly owned Australian company and has been operating since 1911 building high quality products The information in this manual will assist your installer and ensure correct location and connection Thoroughly read the user instructions and the user maintenance sections as understanding your products its operation and its cleaning and service requirements will provide you with long and satisfactory service Failure to do so could shorten the life of the product and decrease its efficiency Please ensure only authorised service technicians are called to any difficulties that may arise INTRODUCTION GOLDSTEIN TEPPANYAKKI MODELS TK 24 TK 30 TK 36
6. TIC cleaners ARE NOT TO BE USED otherwise warranty will be void Clean down plate at the end of each working day Thoroughly wash all traces of cleaner off Teppanyaki plate with lukewarm soapy water then rinse again and again with fresh water and wipe thoroughly Lightly coat plate with oil NOTE Ensure to empty out the grease can regularly while cleaning griddle otherwise grease can will overflow Let griddle plate run on high for a few minutes to completely dry the water from the plate Using a basting brush after plate is completely dry and cool cover the plate with a thin layer of cooking oil to maintain the shinny appearance of the plate When cleaning the stainless steel surface under NO circumstances should wool brushes or scraping implements of common steel be used on the stainless steel because ferrous particles can deposit on the stainless steel surface causing by their oxidation rust spots Scotchbrite can also be used but it is necessary to always rub the surfaces in the direction of the stainless steel finish If the appliance is to remain inoperative for a certain period cover the Teppanyaki plate with a thin layer of cooking oil note that it is advantageous to keep the room in which the appliance is installed Note IF CAUSTIC SODA BASED OVEN CLEANERS ARE USED WARRANTY IS VOID IM083B1 p12 Goldstein 9 TABLE LOoWbe LL GIN DN SONIA ASSY
7. TK 45 GOLDSTEIN TEPPANYAKI PLATES are designed to give long and satisfactory service and incorporate the best possible materials and workmanship Proper installation adjustment and preventative maintenance are vitally important if efficiency and appearance are to be maintained Read these instructions carefully as they contain important safety information regarding the installation use and maintenance of the appliance RECEIVING INSPECTION e Check crates for handling damage After carefully uncrating check for concealed damage Report any damage immediately to carrier and to dealer Remove check all loose items from unit and check contents as found on back of warranty cards e Check type and capacity of gas supply e The type of gas for which this Teppanyaki is factory adjusted can be seen on the rating plate located on the front Control Panel THE EQUIPMENT MUST BE INSTALLED BY LICENSED GASFITTER IMO83B1 p3 Goldstein 2 INSTALLATION INSTRUCTIONS SS INSTALLATION OF THE TEPPANYAKI Check that there is sufficient clearance between doors and passageways to move equipment into the cooking area 2 Remove banding and cardboard outer 3 Lift off wooden base 4 Push in legs and tap in with a hammer into tubes If required mount on stand OPTIONAL INSTALLATION FOR AUTHORISED TECHNICIANS ONLY Note AFTER ANY MAINTENANCE OR ADJUSTING OF GAS CONNECTED COMPONENTS A GAS LEAK TEST MUST BE CARRIED OU
8. e appliance manifold and union NOTE Models operating on LP Gas will be supplied with a regulator as from 1 January 2005 as new standard AS4563 AG300 IM083B1 p4 Goldstein 2 INSTALLATION INSTRUCTIONS 3 All equipment must be sitting level for proper operation and combustion where plinth type installation is made plinth height and front overhang must be 50 mm minimum Levelling can be made by the use of metal shims For griddles where adjustable legs are provided levelling can be made easily due to the threaded construction of the legs Licensed plumber should make connection to main gas line Install a hand shut off valve in gas line to the appliance manifold IMO83B1 p5 Goldstein OPERATION FOR AUTHORISED TECHNICIANS ONLY Note All the appliances that leave our factory have been tested and adjusted according to the specifications for the required gas The regulator may have to be adjusted to achieve the required gas pressure Note Before igniting the Teppanyaki plate remove the protective coating on the plate with solvent e g mentholated spirits Ensure that the pressure at the pressure test point on the manifold is as per the rating plate If the pressure is not the same use a screwdriver to adjust the pressure regulator turning screw clockwise will increase the pressure Turn the control knob to low and check that the flame size has decreased substantially If flame has not decreased then using a
9. lity for or in respect of any claim arising out of contract negligence or statute shall not in any event exceed 100 Labour under warranty is supplied free of charge during normal working hours Monday to Friday Should warranty work be requested outside of our normal working hours a labour charge will be applied equivalent to a normal hour rate without out of hours penalty rates Refer to last page of this manual for your closest branch for warranty repair services IMO83B1 p16 13 J GOLDSTEIN amp LTD BRANCHES Goldstein For inquiries please call your nearest state branch Head Office 211 213 Woodpark Road New South Wales 2564 Phone 02 9604 7333 Fax 02 9604 5420 Victoria Queensland Unit 13 Unit 3 260 264 Wickham Road 49 Logan Road Moorabbin Woolloongabba Victoria 3189 Queensland 4102 Phone 03 9553 1488 Phone 07 3891 1466 Fax 03 9553 0785 Fax 07 3393 1333 South Australia Suite 26 283 287 Sir Donald Bradman Drive South Australia 5032 Phone 08 8238 3423 Fax 08 8238 3400 IMO83B1 p17 Western Australia 10 Wittenberg Drive Canning Vale Western Australia 6155 Phone 08 9456 0559 Fax 08 9456 0554
10. small flat headed screwdriver adjust the min gas screw on the front of the gas control until the min flame gets to desired size turning screw clockwise will decrease the flame size Turn the Teppanyaki plate off and apply a coating of cooking oil to the whole griddle plate surface Failure to do this will cause the warranty to be void NOTICE PLEASE RETURN YOUR WARRANTY CARD FAILURE TO DO SO WILL VOID WARRANTY ON THE EQUIPMENT IM083B1 p6 Goldstein OMM ONING INSTRUCTION To be carried out by Gasfitter or Authority service person COMMISSIONING APPLIANCE DETAILS TESTING CHECKING PRESSURE ETC 10 COMMISSIONING CHECK LIST CHECK FOR DAMAGE AND MISSING PARTS ON BACK OF WARRANTY CARD REMOVE ALL PLASTIC COATING FROM S STEEL PANELS MAKE SURE ALL PARTS ARE IN THEIR CORRECT POSITION E G TRAYS BURNERS KNOBS MAKE SURE ALL ELECTRIC AND GAS CONNECTIONS ARE CORRECT AND TIGHT LEVEL OFF UNIT LEFT TO RIGHT AND ALSO MAKE SURE THAT FRONT IS JUST 3 4 MM LOWER TO ALLOW FOR FLUING TURN ON GAS OR ELECTRICITY ADJUST GAS PRESSURE WITH THREE QUARTERS OF THE UNIT RUNNING ADJUST GAS PRESSURE NATURAL GAS 1 00 KPA LPG 2 65 KPA TURN ON ONE AT A TIME TO MAKE SURE ALL IS WORKING E G BURNER RADIANT GRIDDLE AND OVEN SHOW CUSTOMER A HOW TO WORK EQUIPMENT B HOW TO CLEAN C HOW TO PULL IT APART E G TRAYS TRIVETS D ALSO WHAT NOT TO DO E G WATER WITH ELECTRICAL GREASE AND OIL IN CONTROLS CHECK
11. ugh an injector spud This spud needs to be replaced when converting between N G If appliance cannot be correctly adjusted advise the local gas authority or the appliance manufacturer CONTROLS The only controls are the PEL 21S gas valves All are accessible after the front stainless steel fascia is removed If controls get hard to turn get a service man to remove the two screws at the front of the control and put a high temperature graphite grease on the shaft IMO83B1 p10 Goldstein INJECTOR SIZES Conversion to other gases Injector Drill N G 3 10 32 L P 1 85 49 CONVERSION INSTRUCTIONS To convert from N G to L P gas do the following 1 2 4 5 Replace N G burner injectors with L P injectors refer to table this page Replace pilot injectors to required size N G 32 L P 22 Disconnect regulator from gas supply line Reconnect LPG regulator Reset pressure test point on manifold to 2 75 kPa Adjust burner aeration slide Relevant required gas pressures for use in conversion Natural 1 0 kPa W G L P 2 65 kPa W G Town or manufacture gas 0 625 kPa W G IM083B1 p11 Goldstein 8 CLEANING INSTRUCTIONS CLEANING MAINTENANCE OF TEPANYAKI Frequently during the cooking clean Teppanyaki plate with a high heat spatula this will prevent food build up and will make the final daily cleaning of the Teppanyaki plate easier Use a mild cleaner CAUS
Download Pdf Manuals
Related Search