HT129 User`s manual - Föhrenbach Application Tooling nv.
Contents
1. 3 1 The hand tool is equipped with a ratchet mechanism to provide appropriate crimp condition Therefore it is impossible to open the handles before closing them completely releasing ratchet 3 2Place the hand tool in your right hand so that movable handle can be actuated by you thumb then open the handles completely 3 3 Hold the contact section of the terminal then insert a terminal as shown in figure 3 3 4Close the handles gradually until the terminal is held between the crimper and anvil During this operation the terminal should be relocated so that the end of the contact section touches the crimper see figure 3 3 5Place a stripped wire into the wire barrel so that insulation of the wire touches the crimper or the wire barrel Note if each of the strands is dispersed it sometimes causes strands to be left out of the barrel after crimp operation finishes resulting in crimp failure 3 6 Close the handles completely until the ratchet is released 3 7 Finally take the crimped terminal out of the hand tool 2 rae een Crim my Wire bar e he m Cantac a SA iR In latas BEL It 3 E J F a barrel k E TERN i E stiri poed 2 ern rn 9 ee pub La ee a u el z z AN nn a 1 8 me 2G ET ee Ihe end oot antec rs Anvi section should O07 4s the erimper Figure 3 Instruction manual HT 129 HT130 www foehrenbach be Date August 2007 Rev 4 Page 3 4 E F hrenbach Application Tooling2. 4 Maintenance and precaution To use the hand tool without any trouble for extended time observe following 4 1 Don t drop or use the hand tool as a hammer 4 2 After use of the hand tool always clean and lubricate the crimper and anvil to prevent rust built up and keep the handles close to avoid foreign particles in the crimp sections 5 Contact F hrenbach Application Tooling N V Krijgsbaan 128 2640 Mortsel Belgium Tel 32 3 216 19 98 Fax 32 3 216 15 07 URL www foehrenbach be The technical data in this publication has been carefully checked and assembled No liability from inaccuracies or errors is assumed The right to change or improve this document without notice is reserved Instruction manual HT 129 HT130 www foehrenbach be Date August 2007 Rev 4 Page 4 4
3. HT129 HT130 Handpistol Relimate AWG 22 26 User s Guide F hrenbach Application Tooling E Fohrenbach Application Tooling 1 General This manual describes the operation and maintenance of Fohrenbachs handtool HT129 and HT130 which are designed to crimp Relimate terminals on the specified wire Please read this manual before using the handtool eo cjustment roc f Biv w HT nunker f j E Rij e ae n i E i rail j i wt k h J ka a a e hj u u T B Tu s I nn al rd _ n kt eas N Er inpar p Raten er pS I Movable handle E k Sr ee ETE F ee Figure if 2 Terminal and applicable wire range 2 1 Partnumber and applicable wire range are listed in Table 1 The crimper has two crimp sections at the both ends see figure 2 and applicable wire size is indicated next to the crimp sections The crimper can be interchanged after pulling out adjustment rod shown in figure 1 2 2 Wire stripping Make sure stripped length of the wire is in the range of 1 8 to 2 3 mm Be careful not to make cuts or nicks in the strands during the stripping operation loose piece AWG diameter mm 76806 001 HT129 0 74 0 05 24 26 26 26 28 Ba ER 28 30 Table 1 az seen fN Cj E PEN IT ER Iza al he 129 4 13C Figera 2 Instruction manual HT 129 HT 130 www foehrenbach be Date August 2007 Rev 4 Page 2 4 E Fohrenbach Application Tooling 3 Operation instruction
Download Pdf Manuals
Related Search