400 Clip Instant Access System Native Protocol
Contents
1. NDF non drop frame DF drop frame STOP MODE PB while playing a clip when STOP is pressed the Profile freezes on last good video PB EE When STOP is pressed the first time the Profile freezes on last good video When STOP is pressed a second time video out is switched to video in WIND MODE Press Softkey to select HOLD fast wind is maintained only while key is depressed OR LATCH fast wind is initiated and maintained with momentary key press Select fast wind speed 04X etc by pressing Softkey SLOMO ST300 display shows SLOMO with WHEEL Non T Bar version SpdRange Preset SLOMO with Wheel ST300 display shows T Bar version NOTE The T BAR has a fixed speed range of 0 gt 200 with a detent at 100 play speed For Wheel only Press Softkey SPDRANGE to select SLOMO speed ranges Press Softkey to select 0 gt 200 OR 100 gt 200 Press Softkey BACK to return to SEOMO MENU Press ESC to exit OR turn the Wheel to select another item For Wheel only Press Softkey PRSET to select the SLOMO Preset Speed Mode Press Softkey UPDATE When exiting SLOMO mode the last used speed is saved in the Preset Speed register Press Softkey STATIC The Preset Speed register is NOT updated when exiting SLOMO mode It is only changed by SHIFT SLOMO PRESET SLOMO MAX SHUTTLE SPEED Press Softkey to select maximum shuttle speed2. Peripheral Device Address for one of the GANGed VTRs The Trigger will be sent to the enabled VTR The other VTRs in the GANG will perform the same action 11 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option Advanced Features 10 DUPLICATING A CLIP 11 To save copy of a clip first LOAD the clip Set the IN and OUT at the head and tail of the clip Press SHIFT CLIP LIST The display will show Save Trimmed Clip Press LOAD LOAD Yes Wheel Next Enter a numeric CLIP ID using the numeric keypad on the ST300 To add looping functions to the created clips see LOOPING FUNCTIONS Section 13 Press LOAD to save OR Press ESC to abort without saving TRIMMING A CLIP To make a sub clip first LOAD the clip Locate the desired IN point Press IN to set your IN point The IN indicator will turn on Locate the desired OUT point Press OUT to set your OUT point The OUT indicator will turn on Press SHIFT CLIP LIST The display will show Save Trimmed Clip LOAD Yes Wheel Next Press LOAD The display shows Manually enter ID Enter a numeric CLIP ID using the numeric keypad on the ST300 Press LOAD to save the trimmed clip OR Press ESC to abort without saving 12 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 13 12 RECORDING NEW CLIP a To make a new clip and insert video from either another Profile channel or an exter
3. CLIP LIST to view the list of Clips that exist in the VIDEO SERVER The Clip List indicator comes on Create New Clip The display shows LOAD OK WHEEL Next d Turn the Wheel The display will now show XXXXXXXX LOAD OK ENTER ID Where is the eight character CLIP ID Turn the Wheel clockwise to scroll forward or counter clockwise to scroll backward through the list of available CLIPs OR Enter a numeric ID if a clip has one from the keypad Press LOAD to load the current CLIP ID shown on the top line of the display f Locate the clip to the desired IN time If no IN time is set the LEARN and the IN point will be at the current position g Repeat steps a f until clips are loaded into the desired VTRs and set the GANG mode if required NOTE MULTIGANG SUPPORT 2 gangs are allowed to exist on the ST300 simultaneously As long as the loading of a Cue Point or a selection of a gang does not interfere with another gang any gang is legal 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 9 CAPTURE FUNCTION a SETTING THE IN OUT POINT 1 Locate the clip to the desired IN OUT time 2 Press IN The IN OUT indicator comes on CLEARING THE IN OUT POINT Press and hold DEL then press and release IN The IN OUT indicator goes off LEARN a LEARNING IN POINTS GANGED CLIPS If a gang is established with the
4. displayed on the top line The bottom line of the display shows CHB CHC gt gt gt OFF Press the keys under these selections to choose a channel Select gt gt gt to view more channels 6 Repeat steps 3 5 for VTRs 2 3 and 4 7 Press ESC at any time to exit menu mode NOTE Set all unused VTR Connections and Channels to OFF 19 COMPLETING THE PROFILE CONNECTION So far in this setup the session has been opened on the Profile and is ready for communication Noting the port session number just selected P1 locate the P1 connector on the Profile s breakout box and connect an RS 422 cable from Port 1 to the connection called VTR1 on the back of the ST 300 The default values for channel connections CHA CHB CHC and CHD on the ST300 are for Upon connection the ST300 will be communicating with the Profile on all available channels This is the connection just built From To Profile Session 1 ST300 VTR1 On Port 1 Connection 1 18 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option PROFILE CONNECTION OPTIONS Open another session and connect an RS 422 cable to another VTR label on the back of the ST300 From the setup menu on the ST300 assign any ST300 VTR to the new connection CN The ST300 VTR just assigned will be communicating on with the Profile via the new connector The program displays a screen titled Channels Assign a V
5. master having an IN point the gang relationship will be relative to the master IN point and all slave IN points will be overwritten If the master has no IN point the current location of each clip in the gang will be learned as IN points IF the slaves have IN points the slaved in points will be overwritten LEARN ON THE ST300 1 Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display 2 Press SHIFT MARK to initiate the Learn of the current configuration The display shows Select VIR Learn ESC Cancel 3 Press VTR 1 VTR 2 VTR 3 or VTR 4 to select the VTRs Press MARK to complete the LEARN The ST300 will LEARN save the Cue Point CLIP IDs IN and OUT Times Current Directory and Ganged VTRs LEARN ON THE PRODUCTION SWITCHER 1 Select and enable the Peripheral Device Addresses for the ST300 2 Do a LEARN to the desired REGISTER The ST300 will LEARN save the VTR number loaded CLIP ID and current IN time into the REGISTER number in the ST300 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 7 RECALL ON THE 57300 1 Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display 2 Press LOAD o
6. 12843 Foothill Blvd Suite D Sylmar CA 91342 818 898 3380 voice 818 898 3360 fax _______ EE 222 4171 www dnfcontrols com Model No 4000CL N PBIO KBIO amp 4000CL N PBIO T 400 Clip Fast Access System FOR GRASS VALLEY GROUP NATIVE PROTOCOL WITH PERIPHERAL BUS INTERFACE OPTION NOTE Supports up to 4 Video Server Channels USER MANUAL 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 1 1 TABLE OF CONTENTS REVISION HISTORY GETTING STARTED 2 SYSTEM DESCRIPTION FEATURES DEFINITIONS gt 4 5 6 7 8 9 SYSTEM INSTALLATION ST300 S SM VTR DDR CONTROLLER PRODUCTION SWITCHER LOADING A CLIP CAPTURE FUNCTION SETTING THE IN OUT POINT CLEARING THE IN OUT POINT LEARN LEARNING IN POINTS GANGED CLIPS LEARN ON THE ST300 LEARN ON THE PRODUCTION SWITCHER RECALL ON THE ST300 ON THE PRODUCTION SWITCHER PBIO ENABLE DISABLE TRIGGER GRASS VALLEY GROUP SONY 11 ADVANCED FEATURES 10 11 12 13 14 15 16 17 A B 18 A B 9 DUPLICATING A CLIP TRIMMING A CLIP RECORDING A NEW CLIP GOTO LOOPING FUNCTIONS VIEW CONTENT OF CUE POINTS RECUE TRANSFERRING CUELIST TRANSMIT CUE LIST FUNCTION RECEIVE CUE LIST FUNCTION VIDEO SERVER SETUP CONFIGURING T
7. 300 to the VTR4 connector of the receiving ST300 using an RS422 9 pin cable with TX and RX lines crossed A turnaround cable b Press MENU and scroll the Wheel to Transmit CUE List YES Enter Exit ESC Press ENTER to start transmitting The Display shows Waiting to transmit on the first line d When the Receiver is ready transfer starts automatically The Display now shows Transmitting cuelist After the transfer is over the display shows Transfer is over for one second and then shows Waiting to transmit again f Connect another ST300 to transmit the list again OR Press ESC twice to exit the MENU mode 2 To Transmit Cue Points to the PC a Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using a RS422 to RS232 adapter b Repeat steps b f of the TRANSMIT CUE POINTS to the ST300 section 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 16 b RECEIVE CUE LIST FUNCTION The RECEIVE CUELIST function allows you to receive your list of Cue Points from a PC or from another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information 1 To Receive Cue Points from the ST300 a Connect the VTR4 connector on the back of the ST300 from the VTR4 connector of the transmitting ST300 using RS422 9 pin cable with TX and RX lines crossed A Turnaround Cabl
8. HE PROFILE FOR NATIVE MODE OVERVIEW OF PROFILE CONNECTIONS CONNECTION AND CHANNEL ASSIGNMENTS COMPLETING THE PROFILE CONNECTION PROFILE CONNECTION OPTIONS DRIVE DIRECTORY SELECTION NAMING CONVENTIONS 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 2 pi REFERENCE 20 SETUP MENU ST300 SETUP DEFAULTS 21 FUNCTION TABLE 22 SPECIFICATIONS ST300 27 23 KEY LAYOUT 24 DNF CONTROLS LIMITED WARRANTY Manual ccc sccssocosesscsonccasesssoosscsonccdscscseeseees 1 2 080604 Document 3 0 4000CL N PBIO KBIO User Manual 3 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 1 REVISION HISTORY 100103 1 0 Original document 112403 1 1 Updated Transmit Cue List Function and Receive Cue List Function description Added DNF Controls Limited Warranty 080604 1 2 Changed T bar dimension 4 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option Getting Started 2 5 SYSTEM DESCRIPTION NOW production switchers can load amp play video clips on Grass Valley Group PROFILE Use or SNAPSHOT Learn amp Recall functions of the production switcher to load and play a video clip from a Recall or timeline Use the Run and Trigger functions of the production switcher to Play Stop the video clip Instantly load a video clip at the press of a button Control to 4 vid
9. IVE Protocol with PBIO Option 28 15 Pin D Type Female DB15F Function GPI OUT 1 GPI OUT 2 GPI OUT 3 GPI OUT 4 GPI OUT 5 GPI OUT 6 GPI OUT 7 Common GPI IN GPI OUT Function GPIIN 1 RECORD GPIIN 2 PLAY GPIIN 3 STOP GPIIN 4 RECUE GPIIN 5 LOAD GPI IN 6 NEXT CUE GPI IN 7 LAST CUE 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option KEY LAYOUT 23 205280 371934 eM 37034 LHS 9 N 19260 N 34015 ayam ma O O 7 151 4001 AYAIN fy 12000 STOH LNO 3 10 1 02 1 00615 55535 O WAN 07 O O 4710 491 GS HIKS 1 LNOAV T 0015 4000 CL N PBIO NATIVE Protocol with PBIO Option 29 24 DNF CONTROLS LIMITED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one 1 year from the date of sale to the original purchaser from DNF Controls In order to enforce the rights under this warranty the customer must first contact DNF s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair If DNF s Customer Support Department cannot fix the problem the customer will be issued a R
10. TUP MENU The MENU indicator will turn off IMPORTANT NOTE Please set the following MENU items during initial installation ST300 Setup Clear Mem Set Defaults ST300 Config Select Directory MENU MODES Turning wheel Clockwise DISPLAY The version number and date for the currently installed software is displayed For SOFTWARE example VERSION 4000CL N PBIO V3 0 111300 RECORD Press Softkey to select the desired mode Lockout or Crash Full CHANNEL Press VTR key for CH channel and CN Connector assignment CONNECTOR ASSIGNMENT RECORD LOOP Press VTR keys for RECORD LOOP lengths then enter HH MM SS FF TIME RECORD Press Softkey to select single button or 2 button record RECORD REC only OR REC PLAY RECALL MODE Press Normal or Redirect Redir When one clip is learned into a Cue Point the Clip will be REDIRECTED to load on the currently selected VTR If REDIR is off the Clip will be loaded on the VTR it is LEARNED into LEARN MODE In normal mode IN Current time and OUT points as well as any gang information are LEARNED In CLR_LRN mode the IN and OUT points are cleared after LEARN is done This is used to set multiple Cue Points with individual IN and OUT points in the SAME video clip MARK Q Press Softkey to Enable ADVANCE to next Cue Point when MARK is pressed OR Maintain CURRENT Cue Point when MARK is pressed 20 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option
11. Wheel LAST CUE LAST CUE Step to the previous Cue Point Location NEXT CUE NEXT CUE Step to the next Cue Point Location REC RECORD REC Places VTR into the Record mode selected by RECORD MODE in the SETUP MENU Press RECORD or RECORD PLAY REWIND RWD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU SHUTTLE SHUTTLE Select SHUTTLE mode and enable Wheel SAVE TRIMMED SHIFT CLIP LIST Allows trimmed clip to be saved with a different CLIP ID CLIP DISPLAY SHIFT Displays the directory in which the CURRENT Cue Point DIRECTORY NEXT CUE is saved THE CLIPS IN THE CURRENT CUE POINT ARE LOCATED 25 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option DISPLAY SHIFT Displays the directory in which the clips in the CURRENT LAST CUE CURRENT Cue Point is saved WORKING DIRECTORY DISPLAY SHIFT LOAD Display duration of currently loaded clip and which clip is DURATION OF loaded CLIP and WHICH CLIP IS LOADED PRESET SLOMO SHIFT SLOMO Turn the Wheel to preset slo mo speed SPEED SLOMO SLOMO Press SLOMO to slo mo the VTR the Wheel move the T Bar if available to change the play speed Press SLOMO to STILL frame OR Press any transport key to exit SLOMO STOP Press once to STILL frame VTR Press again to put VTR into STOP mode TO LOOP SHIFT Loops from the IN point to the OUT point of a clip LOOP ENABLE continuousl
12. ans hold the two keys down simultaneously Softkey refers to the multiple functions keys located directly below the display window 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 3 SYSTEM INSTALLATION a ST300 S SM VTR DDR CONTROLLER 1 2 3 4 5 Plug one end of a 9 conductor RS422 serial cable into the VTR 1 2 3 or 4 connector on the rear of the ST300 Plug the other end of the cable into the REMOTE connector on the Video Server Connect the 5 12 12 VDC POWER SUPPLY into the POWER connector on the rear of the ST300 Plug the Power Supply into an outlet 90 VAC to 240 VAC Connect the 9 pin connector on the supplied KBIO adapter to the VTR2 connector on the rear of the ST300 Connect a standard PS2 keyboard to the PS2 connector on the supplied KBIO adapter Check SETUP MENU prior to using the ST300 to confirm proper Record mode and other User settable modes See CONFIGURING THE PROFILE FOR NATIVE MODE Section 17 a b PRODUCTION SWITCHER 1 2 3 4 5 6 7 8 Connect a standard cable RS422 9 serial cable to the AUX connector on the rear of the ST300 Connect the other end of the cable to the Peripheral Bus Connector on the production switcher Communication Format 38 4K N 8 1 The ST300 has 4 Peripheral Device Addresses one for each VTR that it controls To set the Device Address for each VTR Press MENU on the ST300 Turn the Wheel clockwi
13. e b Press MENU and scroll the Wheel to Receive CUE List YES Enter Exit ESC c Press ENTER from start receiving The Display shows Waiting to receive on the first line d When the Transmitter is ready transfer starts automatically The Display now shows Receiving cuelist e After the transfer is over the display shows Done Success Press any key f Press any key The display shows Receive cuelist message g Press ESC to exit the MENU mode 2 To Receive Cue Points from the PC a Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using RS422 to RS232 adapter b Repeat steps b g of the RECEIVE CUE POINTS from the ST300 section 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 18 VIDEO SERVER SETUP Configuring the Profile for operation with Grass Valley Group Native Protocol You MUST 1 Configure the PDR AND 2 Open a Prolink session BEFORE the DNF System can be used a CONFIGURING THE PROFILE FOR NATIVE MODE The ST300 Controller with NATIVE protocol communicates with the PROFILE through the PROLINK program on the PROFILE Prolink uses Configuration Files found in the PROFILE CONFIGS Directory These files are called VTR1 CFG VTR2 CFG VTR3 CFG and VTR4 CFG These files do not affect the operation of VDR Panel Prolink and VDR Panel share resources so that the total number of PROLINK channels used and VDR Panels opened can not exceed t
14. efuse repair of any unit outside the warranty period that is deemed non repairable DNF Controls shall not be liable for direct indirect incidental consequential or other types of damage resulting from the use of the product 30 4000 CL N PBIO NATIVE Protocol with PBIO Option
15. eo channels individually or ganged including looping Quickly amp Easily access up to 400 video clips Grass Valley Group PROFILE Quickly access FILL amp KEY clips a single Cue Point LOOP to 4 channels FEATURES The 4000CL N PBIO 400 Clip Fast Access System consists of the ST300 SSM with Cliplist software The 400 Cue Points are saved in non volatile Cue Point memory in the ST300 With the PBIO Option the ST300 has 4 Peripheral Device Addresses one for each VTR that it controls This allows the production switcher to control any and all VTRs connected to the ST300 Upon receipt of the Learn command from the production switcher the ST300 saves the CLIP IDs of the currently loaded clips the current time of each clip the VTRs they are loaded on and the current GANG mode into the appropriate Cue Point When the Recall command is received the ST300 loads the Learned clips onto the Learned VTRs cues the Clip to the Learned time then restores the Learned GANG mode The Trigger function on the production switcher puts the selected VTRs in to Play Stop Recue or other available modes Quickly amp Easily learn and re learn Cue Points DEFINITIONS Throughout this document the Grass Valley Group Profile will be referred to as the Video Server Q The ST300 S SM as the ST300 Q Words surrounded by brackets for example ENTER are keys on the ST300 Q XXX XXX me
16. eturned Merchandise Authorization number RMA The customer will then ship the defective product prepaid to DNF Controls with the RMA number clearly indicated on the customer s shipping document The merchandise is to be shipped to DNF Controls 12843 Foothill Blvd Suite D Sylmar CA 91342 USA Failure to obtain a proper RMA number prior to returning the product may result in the return not being accepted or in a charge for the required repair DNF Controls at its option will repair or replace the defective unit DNF Controls will return the unit prepaid to the customer The method of shipment is at the discretion of DNF Controls principally UPS Ground for shipments within the United States of America Shipments to international customers will be sent via air Should a customer require the product to be returned in a more expeditious manner the return shipment will be billed to their freight account This warranty will be considered null and void if accident misuse abuse improper line voltage fire water lightning or other acts of God damaged the product All repair parts are to be supplied by DNF Controls either directly or through its authorized dealer network Similarly any repair work not performed by either DNF Controls or its authorized dealer may void the warranty After the warranty period has expired DNF Controls offers repair services at prices listed in the DNF Controls Price List DNF Controls reserves the right to r
17. he available number of resources typically 4 channels If CFGEDLIN EXE is in the Profile directory use CFGEDLIN EXE to configure the CFG files If you do not have CFG EXE install PDRCFG EXE Instructions for installing PDRCFG EXE accompany the disk b OVERVIEW OF PROFILE CONNECTIONS Physical access to the Profile is made through its RS 422 breakout box A Profile session activated with Prolink establishes which port s Profile will use for serial communications The communications link is complete when a connection is made from a connector on the ST300 to an open session port on the Profile A correctly configured connection consists of a connector and a channel Connections for the ST300 are called CN1 CN2 CN3 and CN4 and refer to the 9 pin ports on the back of the ST300 labeled VTR2 VTR3 and VTR4 Channels for the ST300 CH A CH B CH C and CH D refer to the Profile s Channel 1 Channel 2 Channel 3 and Channel 4 The numeric alpha translation is made in the ST300 in order to comply with the VDR Panel Software which refers to the numbered channels as Panel A Panel B Panel C and Panel D 17 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option CONNECTION AND CHANNEL ASSIGNMENTS 1 Press MENU to enter Menu Mode 2 Turn Wheel until Press VTR key for CH and CN assignments is displayed 3 Press VTR 1 key NOTE VTR X toggles between CH and CN assignments 4 VTR 1 Connection is
18. ideo Audio and Timecode CODECs Video Input and Video Output as required to Channels 1 4 If a resource is in use it will be highlighted in Red Click OK when all assignments have been made b DRIVE DIRECTORY SELECTION To change the PROFILE Drive or Directory where Clips will be saved 1 Press MENU and scroll to the Drive Directory selection 2 Select Drive or Directory by pressing the Softkey under the menu item 3 Scroll to the desired Drive Directory and press ENTER The selected drive directory will be used for locating and loading clips NOTE When a Drive Directory changes the Clip List created using a different Drive Directory is no longer valid Set all unused VTR Connections and Channels to OFF NAMING CONVENTIONS The ST300 Native Mode Controller can load clips that meet the following requirements 1 On the 8 character versions clip names cannot exceed 8 characters Otherwise clip names may be up to 32 characters 2 A space cannot be embedded within the Clip Name 3 The clip name must be in upper case characters only 4 All special characters can be used 19 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option Reference 20 SETUP MENU Press MENU The MENU indicator will turn on Turn the Wheel to select item to change Press MENU OR use the Softkeys to change the desired mode for that option Turn the Wheel at anytime to select another item Press ESC at anytime to exit SE
19. ip should be loaded in loop mode All the clips in the Gang will loop when PLAY is pressed Press LOOP ENABLE after clip is loaded to place clip loop mode Slave Channels will loop when the Master Clip loops NOTE Clips will now loop from the IN point to the END of the clip or the OUT point if set f Press LOOP ENABLE SHIFT to Play To Loop 15 VIEW CONTENT OF CUE POINTS a Select the VTR for which you want to examine the contents of a Cue Point by pressing 1 2 3 or 4 b Press NEXT CUE or LAST CUE to step forward or step backward through the Cue Points OR Enter 1 2 or 3 digit number on the numeric keypad followed by ENTER The contents of the selected Cue Point are shown on the bottom line of the display 16 RECUE Press RECUE to go to the beginning of the clip when 2 or more VTR connectors are used DO NOT press REWIND as this may cause the offset between clips to be lost 14 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 15 17 TRANSFERRING CUELIST The TRANSMIT CUELIST function allows you to transmit your list of Cue Points to a PC using the provided utility software on the PC or to another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information a TRANSMIT CUE LIST FUNCTION 1 To Transmit Cue Points to the ST300 a Connect the VTR4 connector on the rear of the ST
20. lected upon reset If the Profile s working directory is changed by other programs when the ST300 starts it will change to the directory last chosen from the menu When installing an upgrade eprom you should Clear the cue point memory Set factory defaults Set the directory You must then reenter your CLIP IDs at the appropriate Cue Points or download them from a PC to which you have previously saved the list using the Transfer Utility or Operator s Suite You should also enter into the MENU any changes you wish to use Failure to follow this procedure may lead to corruption of the Clips and unpredictable operation 24 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 21 FUNCTION TABLE Function Key Press Description GOTO ENTERED SHIFT Search the VTR to the manually entered time TIME Use the ST300 numeric keypad Press ENTER or RECUE SHIFT VTR 1 One at a time press the VTR keys to be included in the OR gang The LED above the key will turn on SHIFT VTR 2 OR Press the VTR key again to remove from gang the LED SHIFT VTR 3 above the key will turn off OR SHIFT VTR 4 Press ESC to exit and save the gang The VTR LEDs that are on show the gang The flashing LED shows which VTR is currently selected and is monitoring Time Code on the display FFWD FFWD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU JOG Select JOG mode and enable
21. n the ST300 The ST300 will automatically load the Learned clips on the Learned VTRs cue the clips to the Learned time then set the Learned GANG mode b ON THE PRODUCTION SWITCHER RECALL the desired REGISTER NUMBER The ST300 will automatically load the Learned clips on the Learned VTRs cue the clips to the Learned time then set the Learned GANG mode 10 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 8 ENABLE DISABLE On the ST300 press the PBIO key to enable or disable PBIO When disabled the ST300 will ignore all Pbus commands When enabled the ST300 will respond to all Pbus commands When enabled and Pbus commands are received the key s LED will flash 9 TRIGGER The operator fires a trigger using either the Timeline or Run function on the production switcher The ST300 puts the Video Server into the following modes based upon the trigger value GRASS VALLEY GROUP Trigger Value Mode 0 Play 1 Recue to beginning of clip 2 Slo mo using ST300 Preset Speed 3 Reverse Play 4 Still Frame 5 Loop Play 6 or greater Play SONY Trigger Value Mode 0 Recue to beginning of clip 1 Play 2 Slo mo using ST300 Preset Speed 3 Reverse Play 4 Still Frame 5 Loop Play 6 or greater Play To control more than one VTR enable the Peripheral Device Address for the required VTRs The Trigger will be sent to the enabled devices OR GANG the required VTRs on the ST300 See the Menu Table for GANG instructions Enable the
22. nal source first press CLIP LIST The Clip List indicator comes on Since there is no clip loaded Create New Clip the display now shows LOAD OK Next b Press LOAD The display shows Manually enter ID Enter a numeric CLIP ID using the numeric keypad on the ST300 Press LOAD to save the new CLIP ID OR Press ESC to abort without saving d Recall the Clip and then start the video that will be inserted Press RECORD f Press STOP when finished 13 GOTO a Press SHIFT RECUE to enter a search time b Enter the desired time using the numeric keypad Press RECUE OR ENTER GOTO the selected time 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 14 LOOPING FUNCTIONS a DEFINITIONS Loop Play from the IN point to the OUT point continuously Play to Loop Played from the beginning of clip to the OUT point of the clip then playback continues at the IN point of the clip then the clip plays in a continuous loop from the IN point to the OUT point b To automatically loop clip each time it is loaded assign the suffix to the clip For example clip named TEASER would be named to loop each time it is loaded To automatically Play to Loop assign the suffix to the clip For example a clip named Game would be named Games to Play to Loop each time it is loaded d To loop clips in GANG mode the Master Cl
23. of the Profile 21 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option ST300 CONFIG Press Softkey DRIVE then press Softkeys to save the default drive or turn the Wheel to change the drive Press Softkey ENTER to return to the ST300 CONFIG screen Press Softkey DIRECTORY to save the default directory or turn the Wheel to change the directory Press Softkey ENTER to save the selected directory and return to the ST300 CONFIG screen NOTE Choose default when first setting up the system or when eproms are upgraded PBIO ADDRESS Press VTR key to assign PBIO address Display shows PBIO Address 00 Enter 00 23 Enter address using numeric keypad Repeat for all VTRs assigned SWITCHER TYPE Grass Valley Group OR Sony Philips DD35 with PBus use PARITY Select type Switcher is set to on the PBUS ODD EVEN NONE DATA PORT Select the VTR Connector 1 4 through which the cuelist may be transmitted or received TRANSMIT Transmits Cuelist to another ST300 or to a PC CUELIST RECEIVE Receives Cuelist from another ST300 or a PC CUELIST SET TO PROFILE Press Softkey YES to set ST300 to parameters currently stored in the Profile MODE UNASSIGNED Recovers Profile resources which have been opened by another device PORT OPTION Press any key to allow the ST300 to report any unassigned resources When prompted select VTRs 1 2 3 or 4 for any unassigned resources AUTO O
24. ption will automatically realign slaves which are not on the same connector as the ALIGNMENT master The master MUST be the clip that has the smallest TM when the two clips are synced This automatic realignment will occur upon pressing stop or after one second has elapsed while in still The second delayed realignment will occur only in Shuttle Slo mo and Jog NOTE This function is supported only in systems with the A option installed 22 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 57300 SETUP 57300 SETUP Clear SetDefault Press Softkey beneath ClearCues to clear all Cue Points to 00 00 00 00 Press Softkey YES when asked Are You Sure Press Softkey beneath SetDefault to set ST300 to default settings SAVE USER DEFAULTS Press Softkey YES to save 23 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option ST300 SETUP DEFAULTS 4000CL N P RECORD Crash CHANNEL CONNECTOR for all CHB CHC CHD respectively ASSIGNMENT RECORD LOOP LENGTH 00 00 00 00 RECORD RECORD REC Only RECALL Normal LEARN MODE Normal mode MARK Q CURRENT Q TAPE TIME NDF STOP MODE PB WIND MODE LATCH MAX SHUTTLE SPEED 8X ST300 CONFIG Drive INT Dir Default SLOMO with Wheel DATA PORT CN4 AUTO ALIGNMENT OFF Auto Align is an option it is not installed in all units NOTES The directory chosen in the menu will be the directory se
25. se until Peripheral Address is displayed Press VTR 1 VTR 2 VTR 3 or VTR 4 to select VTR Assign a Peripheral Device Address for that VTR from 0 to 23 by entering the desired address using the numeric keypad Address 24 or greater will turn PBIO off Select the next VTR then assign a Peripheral Device Address for it from 0 to 23 by entering the desired address using the numeric keypad Each VTR must have its own unique address To select a Production Switcher type Default Grass Valley Group a Press MENU on the ST300 b Turn the Wheel until SWITCHER is displayed Press the Softkeys to toggle between Sony and Grass Valley types of Production Switcher 6 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 9 When done press ESC to exit the MENU 10 Configure the production switcher Enable the Peripheral Bus Enable the Peripheral Device Addresses assigned to the ST300 Enable the appropriate Learn Recall levels Enable the Timeline or Recall Trigger function Installation is complete Connection Diagram ST300 SSM REF VIDEO 3 4 Production 2 2 VIDEO Switcher POWER 2 GPI IN OUT SERVER RESET PIN1 5v PIN3 GND POWER Supplied SUPPLY PS2 Adapter PS2 KEYBOARD 7 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 8 LOADING A CLIP a Select a VTR by pressing VTR 1 VTR 2 VTR 3 or VTR 4 b Press
26. y LOOP ENABLE SHIFT PLAY Plays clip from beginning to end then loops GOTO end of CLIP SHIFT F Position to last frame of clip FWD GOTO beginning of SHIFT REW Position to first frame of clip CLIP TIME MODE TIME MODE Press to toggle between Timecode TC VITC VT or SELECT Tape Timer TM display modes 26 4000 CL N PBIO KBIO NATIVE Protocol with PBIO Option 22 SPECIFICATIONS ST300 Power 90 VAC to 265 VAC adapter supplied with IEC connector Size L x W x H 12 x 6 x 1 5 front 3 0 rear T Bar unit is 12 6 long Weight 4 165 Rear Panel Connectors VTR1 VTR2 VTR3 VTR4 All DB9F GPI DBFI5F Power DB9M Aux DB9F Display Easy to read 2 line back lit LCD display User adjustable contrast Jog Shuttle Wheel With mechanical detents Optional Slo mo 0 200 of Play Speed RS422 SERIAL CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 6 Receive Common 2 Receive A 7 Receive B 3 Transmit B gt 8 Transmit gt 4 Transmit Common 9 Frame Ground 5 Spare AUX PORT PBIO CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 6 Transmit Common 2 No Connection 7 No Connection 3 Receive B 8 Receive 4 Receive Common 9 Frame Ground 5 Spare POWER CONNECTOR 9 D Type DB9M Pin 1 5v DC 6 5 VDC 2 5v DC 7 Ground 3 Ground 8 Ground 4 12 VDC 9 Ground 5 12 VDC 27 4000 CL N PBIO KBIO NAT
Download Pdf Manuals
Related Search