Home

User Manual HWM85-1482

image

Contents

1. AN Attention Small objects like buttons etc or sharp items zips amp buckles may cause damage to the machine which is not covered by the manufactures warranty Garments without hems underwear and finely woven textile such as fine curtains are to be put into wash bag it is better not to wash them ina washing machine Close zippers and hooks make sure the buttons are sewn on tightly and place small items such as socks belts bras etc in the wash bag Unfold large pieces of fabric such as bed sheets bedspreads etc Turn shirts inside out First wash When first using the washing machine let it run unloaded for one complete program to prevent the laundry from being tainted by oil or dirty water from within the machine You should run the machine without laundry but with detergent with a 60 C program pen the washer door put in the laundry piece by piece Close the door tightly Loading the appliance Open the washer door put in the laundry piece by piece Close the door tightly Do not overload the washing machine Selecting Detergent The washing efficiency and the performance are determined by the quality of detergent used Special non foaming detergent produces good washing results Use specific detergents for synthetic and woollen goods Do not use dry cleaning agents such as trichloroethylene and similar products A Do not add more detergent than needed otherwise it may cause the following si
2. make it symmetrical inside the drum 2 Lower the wet weight of laundry pieces by wringing manually and placing them back in the drum in symmetrical position 3 Take out and then reposition the laundry piesces inside the washing machine ina more balanced position on the inner wall of the drum 4 Add 1 or 2 pieces of laundry into the drum to reduce the unbalanced load effects 5 Restart the spin cycle by closing spin programme In case the failure persists please ask a qualified technician to repair it When the above error code displays we suggest switch off the power and restart the machine to operate again If error still exists please contact the maintenance personnel 20 Technical Data Control panel lock function Press the Delay and the Start Pause buttons simultaneously for 3 seconds after starting a program It can no longer be changed by operating buttons or knobs To unlock press the Delay and Start Pause buttons again for 3 seconds O Power off memory function In case of abrupt power failure or the need to cut off the power during a program cycle the present settings will be saved and the preset operation will resume when the power is on again To cancel a program Press the Start Pause button then switch off the power and the program is automatically cancelled Turn the program selector again to choose another program A During the spin process if too much foam is inspected in order to
3. holes corresponding to the screw holes of the feet Then screw the feet back on through the cover and fix it securely to the bottom of the machine fig2 The base keeps out any dampness and reduces the noise Removing the transportation bolts The transportation bolts are designed for clamping anti vibration components inside the washing machine during the transportation process Y Remove the back cover Fig 1 Y Remove the four bolts on the rear side and take out the synthetic stabilisers from within the machine Fig 2 v Replace the back cover Fig 3 V Fill the holes left by the bolts with blanking plugs Fig 4 A When replacing the back cover ensure the convex surface is facing outwards and insert the back cover between the gaps as shown in Fig 5 A Keep the transportation bolts and synthetic stabilisers in a safe place for later use Adjusting the feet There are adjustable feet under the bottom of the washing machine Before use they should be adjusted so that the machine is level This will minimize vibrations and noise during use It will also reduce wear and tear We recommend using a spirit level to level the appliance The floor should be as stable and flat as possible Before use Inlet Hose A Connect the nut on the inlet hose to the connector on the water valve fig1 v Apply inlet hose to a water tap with cold fresh water fig2 A Use the hose set supplied with the appliance Old hos
4. pages 10 11 and 12 Setting washing temperature Press and hold down the temperature button until the desired temperature is selected Setting spin speed Press and hold down the speed button until the desired speed is selected See Operational functions on the Control panel pages 10 and 11 for selecting temperature and spin speed Set to the value recommended by the garment care instructions preprogramed settings Washing Press the Start Pause button The washing machine will operate according to the pre set programs The washing machine will stop operation automatically when a washing cycle ends The End sign will appear on the display Open the washer door and remove the laundry After washing Turn off the water supply and unplug the power cord Open the washer door to prevent formation of moisture and odors Leave the door open while not used Care Chart 0 Machine A Hand Wash WW Tumble Dry NO Sl Do Not al Iron Steam or Dry with E Wash COLD i HEAT F Tumble Dry Line LOW HEAT Machine Do Not Was Dry E Iron Steam or Dry wi y with Tumble Dry LOW 29 Wash Bleach as needed E D E MEDIUM HEAT WARM HEAT Drip Dry l PeR Any bleach like Clorox Iron Steam or Dry with achine G nee may be safely used Tumble Dry Flat Ga HIGH HEAT Dry MEDIUM EJ Machine CH Gi SUE gt q y A Non chlorine Bleach as ont ary clean Do Norton Wash COLD needed Use only a color Tumble Dry HIGH with Steam t Permanen
5. cable when unplugging the mains supply v Make sure that the fuse in the power circuit is rated for 10Amps v Keep away from heat sources and direct sun light to prevent plastic and rubber components from aging v Make sure that the power cord is not caught under or in the appliance and avoid damage to the power cable Y Check that hose joints and connections are firm and no water can leak If joints are loose or there is leakage turn off the water supply and refit Do not use the washing machine until the hoses are properly fixed Do Not X Touch or use the appliance when barefoot or with wet or damp hands or feet SZ Use flammable detergent or dry cleaning agent xX Use any flammable sprays in close vicinity to the appliance X Remove or insert the plug in presence of flammable gas X Allow children or infirm persons to play with the appliance or packing materials SZ Install the appliance outdoors in a damp place or in an area which may be prone to water leaks such as under or near a sink unit In the event of a water leak allow the machine to dry naturally SZ Place the washing machine directly on a carpet J Cautions During daily use of the appliance Do Y Pull up zips and fix loose threads to prevent the items from being entangled If necessary put small items into a laundry bag or pillow case Y Turn off the machine after each wash program and switch it off at the mains to save electricity and for s
6. protect the motor the washing machine will eliminate the foam automatically the motor will stop and the drain pump will drain the water continuously for 90 seconds If it happens more than 3 times the motor will stop until the end of cycle without spinning Technical Data Trouble Shooting Problem Washing machine fails to operate Washing machine cannot be filled with water Machine is draining while being filled Drainage failure Strong vibration while spinning Operation stops before completing wash cycle Operation stops for a period of time Excessive foam in the drum which is spilled to the distribution drawer Automatic adjustment of the washing time Spinning fails Causes x Poor connection to the power supply x Power failure x The washer door is not properly closed x Machine has not been switched on The Start Pause button is not pressed Water tap is not turned on Water pressure is less than 0 03 MPa The inlet hose ts kinked Water supply failure The program knob is not properly set The washer door is not properly closed The inlet hose filter is blocked x Ke KKK Mx ox The height of the drain hose is below 80 cm The drain hose is in water Drain hose is blocked Drain hose end is higher than 100 cm abovethe floor level The filter is blocked Not all transportation bolts have been removed Washing machine is located on an uneven surfaceor is not level Machi
7. remaining time The light turns off and the display disappears when the extra rinse ends 4 Prewash Press the Pre wash button to select or cancel the prewash program button The prewash program can be selected for washing heavily soiled clothes Press the Prewash button tbe Pre wasbh icon will illuminate Press the Pre wash again the prewash function will be cancelled and the Pre wash icon will go out When selecting the prewash function add a proper amount of detergent intothe prewash box otherwise do not add any detergent into the prewash box The Prewash function only applies to Cotton Jeans Synthetics Baby care Daily wash and Mix programs tp PR Functions 5 Rinse Hold Press Rinse Hold button to startup shutdown the crease resistant and sodk function button When the process runs to the last rinse the washing machine is not going to drain clothes will be soaked in water and the soak icon flashes the remain time not decreasing If you need to continue the process you can press Rinse Hold button or Start Pause button then the icon will be off to cancel this function and the washing machine continue to work This feature and the Delay button can not be chose at the same time The tunction is not available for Spin and Express15 programs 6 Start Pause Press the Start Pause button the washer will start and indicator light remains on
8. 8 Er10 EuAr End UNb Causes Door is not properly shut Drainage error water not emptied within 6 minutes Temperature sensor not properly connected or damaged Heater error Appears at the end of a cycle Water level not met in 8 minutes The height of the drain hose is below 80 cm The drain hose is in water Motor Error Water exceeds protective level The signal of Water level sensor is wrong The driving computer and the computer board of display can t communicate End of wash cycle Washing machine has an unbalanced load protection function When unbalanced weight is greater than allowable maximum the washing machine will not spin and will run at a speed to avoid abnormal vibration and noise Solutions Shut the door properly and then press the Start Pause button Clean the filter and check the drain hose for blockage If error still exists please contact the maintenance personnel Contact the maintenance personnel Contact the maintenance personnel Make sure that tap is turned on and water pressure is normal If problem still exists please contact the maintenance personnel Install drain hose within 80 100 cm of height Make sure the drain hose is not in water Contact the maintenance personnel Contact the maintenance personnel Contact the maintenance personnel Contact the maintenance personnel 1 In case washing 1 piece of laundry carpet bed sheet table sheet etc
9. Haier User Manual HWM85 1482 Elements Thanks for purchasing a Haier Product Please read these instructions carefully before using this appliance The instruction contain important information which will help you get the best out of the appliance and ensure safe and proper installation use and maintenance Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance If you sell the appliance give it away or leave it behind when you move house make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings Accessories Check the accessories and literature in accordance with this list Halos 1x Use amp care manual R 1x Base Cover 1X Drain hose bracket ke 1x Inlet Hose 5x Blanking Plugs p d a Index AC UT eebe 4 OO aps tga un e e O o IA 7 A nn A e 10 Mc A O o 18 TO UD NOONE see iio 20 TechnicatData ua ar 23 After Sales Service ccccccccccssssssceccceceseececceeseneseeeceesseeeeeeeeesseeeeeeeeeseeeesseeeesesausseeeeessaausseseeessauasseeeessaagaess 24 Legend Y Yes x lt No e Optional 1 Caution C Attention Cautions Before switching the appliance on for the first time Do v Make sure that the transport bolts are removed Y Usea separate earthed socket for the power supply v Make sure that the plug is accessible v Hold the plug and not the electric
10. If this Button button is pressedwhen the washer is in operation the washer will pause and indicator light will flash 7 Power Press this button to switch on the washing machine Press it again to switch it off Press Switch Start Pause button gently for 2 seconds to switch off the machine as buttons are soft touch sensitive The End sign will appear on the display sfter finishing the program It will change to power off station if there is no operation on the button and none will be shown 8 Program By turning the knob clockwise counterclockwise the required program can be selected knob There are 12 Programs available After a program is selected the corresponding light will go on 9 Washing Press the Temp button to select heating temperature 15 20 30 40 50 60 70 80 90 The temperature maximum allowable heating temperature varise with programs button DA gt in the temperature display indicates non heated washing 10 Spinning Press the Speed button to select spinning speed The maximum allowable spinning speed Speed Setting Varies with programs button A Different water temperatures and spinning speeds can be set for different laundries Wash using the default settings if there is no special requirement 11 Display Display washing time remaining time times of rinsing spinning time temperature setting screen value speed setting value child lock state door lock state washing progress and alarm messa
11. achine is designed for Follow the instructions given on the label of each garment and wash only machine washable garments Cotton 40 C 1400rpm and the normal option selected is recommended water and energy saving cycle for normally soiled everyday washing The detergent dosage rated capacity 12 5g 50 and anti foam aid is 17g Detergent dissolvent method Dissolve the detergent first and pour the dissolved detergent into the machine when the main wash starts gg yf Functions Washing Methods A This washing machine is for domestic use only If the machine is used for commercial purpose the guarantee will not be valid anymore Do not use it for purposes other than that which it was designed Follow the instructions given on the label of each garment and only wash machine washable garments Power Supply Connect the washing machine to the power supply 220V to 240V AC 50Hz Water Connection Cem Turn on the tap The water must be clean and clear EA A O Before use check for leaks in the joints between the tap and the inlet Ga A hose by turning on the tap i Preparing the laundry Sort out the clothes according to fabric type cotton synthetics wool or silk and to how dirty they are i 4 oi Separate white clothes from coloured ones Wash them first by hand to check N if they fade or colours run GAN ETA A Empty pockets keys coins etc and remove hard decorative objects E g brooches
12. afety Wipe clean the lower part of the porthole of any remaining water v Keep the door slightly open when the washing machine is not in use to prevent formation of odours v The power cord must be replaced by the manufacturer service agent or qualified persons if it is damaged Y Ensure that the appliance is not used by people with reduced physical sensory or mental capabilities lack of experience and knowledge without supervision or instruction by a person that responsible for their safety v Supervise children to ensure that they do not play with the appliance Do not X Touch the washer glass door during the washing process it gets hot on the 60 C amp 90 C cycles SZ Place heavy objects or sources of heat or damp on top of the appliance X Hot wash foam rubber or sponge like materials X Open the detergent distribution drawer during the wash cycle SZ Force the washer door pen the door is fitted with a self lock device and will open shortly after the washing procedure is ended Xx Open the washer door if the water level is visibly over the porthole X Cover the washing machine with a cover so that may keep dampness in Cautions Saving Tips Achieve the best use of energy water detergent and time by using the recommended maximum load size Do not exceed the detergent dosages indicated in the manufacturer s instructions The Eco Ball a special system in the outlet will prevent detergent loss from t
13. ctions Ne Function Explication 1 Detergent Open the drawer three compartments can be seen distribution Compartment 1 Prewash detergent drawer Compartment 2 Detergent for programs 1 to 11 Compartment 3 Softener conditioning agent The recommendation on the type of detergents is suitable for the various washing temperatures please refer to the manual of detergent 2 Delay Press the Delay button and the illuminated indicates that the delay function Button is selected The delay time 0 5 24h increases by 30 minutes each press of Delay button The time will change continuously if you press and hold this button until you release it The delay time is the end time of washing For example 6 00 means thewashing ends after 6 hours the delay time must be longer than the program s running time The Delay function is not available for Spin and baby care programs A The delay time must be longer than the program time otherwise the washing machine will start the wash program directly 3 Extrarinse Press this button the washing machine will perform additional rinses button Press the button once to select one additonal rinse The display will show P 1 Press the button repeatedly and the screen will display P 2 or p 3 indicating two or three additional selected rinses The extra rinse light is activated and flashes during performance P 1 2 3 is displayed alternating with the
14. e sets should not be reused Drain Hose Y Use the drain hose bracket to keep the end of the drain hose retained and prevent the outflow of water fig1 Do not extend the length of the drain hose if an extended hose is required please consult a serviceman v The height of the drainage outlet must be 80 100 cm Fix the drain hose to the clip at the back of the washing machine to prevent it from dropping off fig2 A The drain hose should not be submerged in water and should be securely fixed and leak free If the drain hose is placed on the ground or if the pipe is at a height of less than 80cm the washing machine will continuously drain while being filled self siphoning Connecting to the power supply Before connecting to the power supply check v The socket is adequate for the maximum power of the washing machine For safety fuses in the power circuit should be rated for no less than 10A v The voltage should meet the requirement v The power outlet should be capable of accepting the washing machine plug Y Connect the machine to an earthed socket outlet Functions Control Panel 2345 6 7 1 Detergent distribution drawer 6 Start Pause button 11 Display screen 2 Delay button 7 Power Switch 12 Normal washing button 3 Extra rinse button 8 Program knob 13 Speed up button 4 Prewash button 9 Washing temperature button 5 Rinse Hold button 10 Spinning Speed Setting button Operational Fun
15. ge etc 12 Normal Press Normal button to increase the washing time during the main washing stage This washing feature is applicable for full loads of normally soiled clothes and partial loads of heavily hinan soiled clothes The illuminated icon indicates the function is selected This button needs to be selected before starting a program 13 Speed up This button is to decrease the washing time This button is effective before starting a button program and the illuminated icon indicates that the function is selected Functions Program Modes 1 Detergent compartment for prewash mode 2 Detergent compartment 3 Softener compartment NE o a a IO E Temp speed Handwash o 90 c soc y x Cottonfabric s woot osoc soc v x Woolentabric msn weg ooe are v featonersmene soom un one are y race mes cmon oc fave v 0 erone Lime ona ose coterie 1 ms en oc wc permene storm sy co oars we v formen Spe ICC OoOo w xs Functions Consumption Table Program Max Load Temp Washing Time Hand Wash Wool Delicate Mixed Synthetic Cotton Daily Wash Sport 25 Express 15 Jeans Baby Care Spin Drain O The actual water temperature may differ from the declared cycle temperature If the machine is used for commercial purposes the warranty will be void Do not use for purposes other than that which the m
16. he drum to avoid detergent loss into the environment Use Prewash for heavily soiled laundry only Save detergent time water and energy consumption by not selecting Prewash for slightly too normal soiled laundry save energy and time by selecting a high spin speed to reduce the water content in laundry before using a tumble dryer Choose a proper washing temperature Modern detergents can wash with very good result already in lower temperature than 60 C Only y use higher temperature than 60 C for heavily soiled laundry Before Use gt Description This diagram may be slightly different from the layout of the washing machine you have just purchased Control panel Drain hose Work to Water inlet valve Door handle Power cord Start Pause Back cover screws Washer door Back cover gent ammi Transportation bolts Filter cover Unpacking the washing machine Remove all the packing materials prior to use including the polystyrene base Upon opening the package water drops may be seen on the plastic bag and the porthole This is normal phenomenon resulting from water tests in the factory N LOA HI 3 gt Z Re Y VO y 1 mm We WSL HIT Before Use Installation Fitting the base cover Before removing the transportation bolts please fix the base cover to the bottom of the washing machine Lay down the machine fig1 screw off the feet and adjust the base cover with the four
17. into a shallow dish fig3 After the draining process is complete refit the plug into the hose and refit the hose into the housing fig4 amp 5 Remove the filter by turning counter clockwise fig6 Flush the filter clean with running water fig7 Replace the filter by turning clockwise and remount the cover fig8 A The filter must be in place or it may lead to leakage A Place a container under the drain pump filter to collect any excess water that may come out of the drain pump Maintenance Water inlet valve and inlet valve filter To prevent blockage to the water supply by ingress of foreign substances clean the water inlet valve and inlet valve filter regularly Moving the machine If the machine is to be moved to a distance location replace the transportation bolts removed before installation as shown below this will prevent damage Remove the back panel fig1 Remove the blanking plugs fig2 Insert the synthetic stabilizers and the transportation bolts tighten the bolts with a spanner fig3 Replace the rear cover fig4 Long periods of disuse If the washing machine is left idle for a long period pull out electrical plug and turn off the water supply Open the washer door to prevent formation of moisture and odours Leave the door open while not in use 19 Technical Data Display Codes Display Codes and Special functions Codes Errl Err2 Err3 Err4 Err5 Err Err
18. l please separate these items from other types of waste and recycle them This will promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased the product or the relevant local authorities to find out how they can take this item for environmentally safe recycling and safe Business users should contact their supplier and check the conditions of the purchase This product and its electronic accessories should not be mixed with other commercial waste 17 Maintenance Cleaning and Care After washing Turn off the water supply fig1 and pull out the electricity plug after each wash fig2 Open the washer door to prevent formation of moisture and odours If the washing machine is left idle for a long period drain the water in the machine and replace the drain hose Cleaning the detergent drawer Clean the detergent distribution drawer regularly Removing detergent drawer Slide out the draw until the release is visible Flush it clean with water and then replace it Cleaning the machine Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soap liquid to clean the machine case and rubber components Do not use organic chemicals or corrosive solvents Cleaning the filter Clean the filter once a month Open the bottom cover fig1 Pull out the drain tube about 150mm fig2 remove the plug and allow any water to drain
19. ne load is over 8 5kg Water or electricity failure Washing machine gives an error message Washing machine is in soaking cycle The detergent is not a low foaming type or for manual wash Excessive use of detergent x The washing program duration will be adjusted Unbalance of the laundry Solutions Y Check connection to the power supply Y Check the power supply Y Close the washer door properly Y Make sure the machine is switched on Press the Start Pause button Turn on the water tap Check water pressure Check the inlet hose Ensure the water supply Set the program knob property Close the washer door properly Unblock the inlet hose filter mA a Zb 8 Din Za 2 Install drain hose within 80 100 cm of height Make sure the drain hose is not in water N Unblock the drain hose Make sure the drain hose end is lower than 100 cm above floor level Unblock the filter Remove all transportation bolts Make sure the washing machine is on an even surface and levelled Reduce amount of laundry in the drum Check the power supply or water supply Check display codes Press the rinse hold button or the Start pause button again to cancel it Check if your detergent is appropriate Reduce amount of detergent in the distribution drawer This ts normal and doesn t affect the functionality Add clothes or run a spinning program again Technical Data Basic technical informa
20. t safe bleach like Clorox 2 A Ml Dry on clothes O STEET Press Tumble hanger Ei ee EE GE Dry Permanent gt LA Dryclean May appear with additional 5 O RAT Tumble dry letters and or lines Take this item to 109 Wash WARM Ne gh Plas should O eg CH Medium heat A a professional eee EE cl achine Wash S ermanen E Permanent Press or follow bleach package Press LOW HEAT el Las ie omg Pee Machine Wash COLD test procedures to test for Tumble DryPermanent heat Dry cleaning with any Gentle Cycle bleach safety Press MEDIUM solvent NO HEAT ry cleaning with pericloride Gentle Cycle Gentle Cycle LOW HEAT Tumble Dry Gentle Cycle MEDIUM 16 Load Reference Material Made of Load in grams Bed Sheet Cotton Approximately 800 Blanket Wool Approximately 3000 Blended fabric clothes i Approximately 800 Jackets Cotton Approximately 800 Jeans Approximately 800 Overalls Cotton Approximately 950 Ladies Pyjamas Approximately 200 Shirts Approximately 300 Socks Blended Fabric Approximately 50 T Shirts Cotton Approximately 300 Underwear Blended Fabric Approximately 70 Disposal The presence of this symbol on the product accessories or materials that goes with this information indicates that at the end of its useful life the pro duct or its electronic accessories ex charger headset USB cable should be disposed with other household waste To prevent possible damage to the environment or human health from uncontrolled waste disposa
21. tion regarding the appliance HWIM85 1482 Power source 220 240V 50Hz Max working current A 10 Water pressure MPa 0 03 lt P lt 1 Nominal load kg 8 5 Spinning speed r min 1400 Washing programs 12 Max power W 2050 Dimensions HxXDxW mm 850 x 650 x 595 Net weight kg cs Power consumption of the off mode W 0 48 Power consume on of the left on mode W 0 48 23 After Sale Service If after checking the trouble shooting part the problem is not solved Please check the Warranty Card included with the product 24
22. tuations and the washing machine may malfunction impacting on the life of the machine A Due to the increasing foam the rinse me will be longer than normal A The foam may overflow from the detergent drawer because of increased pressure of the foam A The foam may remain in the machine after the final spin and require cleaning out of the machine Recommendation Clean the detergent drawer once a week When using the prewash program please add half of the recommended dosage Please follow the dosage recommendations on the powder or liquid detergent package Adding Detergent Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments Push back the drawer gently Refer to the instructions on the drawer A For prewashing program detergent should be added to both compartments 1 and 2 A For other programs do not add detergent to compartment 1 A Use liquid detergent according to the instructions on its package Do not use liquid detergent if the prewash mode or Delay is selected A Do not overuse softener otherwise it will damage the artificial fibres Selecting wash program To get the best washing results an appropriate washing program should be selected according to the laundry type Please turn the program knob to select the right program Selecting addition functions Select the required options Refer to the Control panel

Download Pdf Manuals

image

Related Search

Related Contents

ーC~822    Poster WEPMN037    La gestion de configuration  MZK-W04NU Wireless USB Broadband Router  Novembre/Décembre 2013 8,87Mo  据付工事説明書  Samsung WB600 Наръчник за потребителя  

Copyright © All rights reserved.
Failed to retrieve file