KR Series - ZKAccess
Contents
1. Auto Card number the modes to search card includes the idle model one time do operations for only a card and the all mode one time do operations for several cards Halt is the sign to do operation for card No Halt is the sign not to do operation for card When the card is done by the Halt operation already system can not finish searching card under Idle mode While under All mode Halt don t affect the card operation and system can search card The above operation please make sure the card is always operated in the antenna range The left window of read and write status displays the card numbers and the communication process2. KR300 User Manual Contents 1 KR300 Profile 2 Appearance 3 Connection with access controller ccccccceeeseessessssesssssssessssssseseeeees 3 1 RS232 Communication ccccccccccccccscecsssssssssssssssssssssssssseseseees 3 2 Wiegand COMMUNICATION 0 0 eee eee eeeeeteceeeeeeeeeeseeseeeeeeaees 4 ID Mifare card operations 0 0 eee eececeesecsecneceseeaeseceseesesseeneeeaeeas 5 Parameter settings of card reader KR300 User Manual 1 KR300 Profile Profile Double frequency product KR300 card reader 125KHz and 13 56MHz Card Reader introduction of foreign core technology update and new production processes completely independent intellectual property rights small power consumption high sensitivity far reading distance high performance low price anti interference strong stability mainly used in smart parking access channel management access control and so on industries built in receiving antenna standard operate frequency 125KHz and 13 56MHz the use of contactless radio frequency ID cards with EM format and IC series Mifare cards Features gt Double frequency design support ID cards and Mifare cards together gt A variety of communication interfaces ID card has interfaces of Wiegand 26 Wiegand 34 Mifare card has interfaces of Wiegand 26 Wiegand 34 RS232 Wiegand 26 or Wiegand 34 can be set by the control system of Wiegand reader and the default setting is Wiegand G26 The Wiegand data for
3. Manual 4 ID Mifare card operations The special card reader module of contactless RF ID card the read distance is from 5cm to 8cm and the supported cards are D cards of thin cards 0 88mm thick and thin cards 1 05mm thick cards 1 88mm with the operate frequency as 125KHz The special card reader module of contactless RF Mifare card the read distance is from 3cm to 5cm and the supported cards are the contactless intelligent Mifare cards with the operate frequency as 13 56MHz Enroll cards through access control device please refer to the relevant document about access control device Note The read distance is impact slightly by the installation environments such as a large area of mental interferences of strong and low frequency signals so it should be far away from the interference sources KR300 Usre Manual 5 Parameter settings of card reader The parameters of KR300 card reader can be read and set by the control system of Wiegand reader The control system of Wiegand reader can set the baud rate of RS232 communication Wiegand model Wiegand control as well as Settings about Mifare card When setting for Mifare card please place Mifare card on the effective sense area of card reader till the complete setting otherwise the invalid operation The operations about the control system of Wiegand reader Open aF ee directly the following window is displayed The softwa
4. egand model set the Wiegand output format of card reader It consists of ID Mifare Wiegand 26 Wiegand 34 Wiegand26 control set the falling edge s width of Wiegand data s each bit and the rising edge s width among bits The default data setting of effective low level is as 50us and the data space is as 1MS Get reader version get the version number of reader S50 S70 This window is used to do operations for the cards It consists of read card write card and card number Bie GH Siga 0 E tester aden 0 LE nebo of tits Pree rr rr errs LOO Gite ON rA tet o the Stat ibe 0 ig Munta ot lcs FF FF FF z FF g The tyes block tay TFET IY EE PEPE TF IVEY the Dame her ibe to Cand ne oe OM gme One Read card it includes the access model control Idle and All KeyA and KeyB number of blocks that is the number of blocks to be read the range is 01 04 the start address of the blocks to be read the range hex 10 KR300 User Manual 00 3F that is from 00 block to 63 blocks the six bytes block key This operation can be set as Auto Write card it includes the access model control Idle and All KeyA and KeyB number of blocks that is the number of block to be written the value range is 01 04 the start address of the blocks to be written the range hex 00 3F that is from 00 block to 63 blocks the six bytes block key the data for write to the card This operation can be set as
5. mat of card reader can also be set by the control system of Wiegand reader gt Support to output the serial number of card at the same time also do read and write operations for Mifare cards KR300 Usre Manual Small size lightweight and compact appearance Red light green light the buzzer with external control interfaces Since using epoxy resins to seal completely interferences of severe environment can be reduced to the minimum Technical parameters gt VV VV V WV Operate frequency of built in receiving antenna ID as standard 125KHz and Mifare as standard 13 56MHz Read response speed less than 0 2s Power supply specification DC12V Operate current 1OOMA Appearance size 77 5 43 5 16MM L W H Supported cards ID cards and Mifare cards Read distance greater than 3CM The distance is varied with the card Communication distance RS232 is greater than 10 meters and Wiegand is greater than 50 meters Operate temperature 10 C 75 C low temperature and high temperature may affect the product if performance changed it will restore naturally after temperature recovery KR300 User Manual 2 Appearance Indicator light Connection terminal Sense 4 area Front View Side View Back View Indicator status when power on the buzzer will have a prompt sound of di indicating the complete initialization at the same time the red light will be lighted up When bru
6. re window is divided into two parts the left is to display read and write status and the right is to display three operational windows of COM setting System setting and 50 S70 Three operational windows KR300 User Manual are switched by three corresponding buttons at the bottom COM debugging assistant Before connecting the card reader the parameters in this window should be set well that is the handshake protocol As above shown this window consists of three parameters communication port baud rate system address Select the corresponding data according to the actual situation In general it is as the default state that is the communication port to COM and the baud rate 115200 selected System command This window is used to set baud rate set Wiegand model get reader version and set Wiegand 26 control Set baud rate set the baud rate of RS232 communication between card reader and host This baud rate will be stored into EEPROM as newly default baud rate After setting successfully the card reader will use new baud rate immediately There are five options of 9600 19200 38400 57600 115200 when clicking the drop down list The communication 9 KR300 Usre Manual speed is varied with the set value Since high speed when high value the default baud rate is as 115200 Press the setting button to apply then the left window of read and write status will display the communication process Wi
7. shing the card the buzzer will have a prompt sound of di at the same time the red light is off later the green light will flash once when in standby the red light will be constant on Sense area sense area of card Connection terminal definitions Cable color and Function Type definition Power Red DC 12V DC 12V connection Black GND Ground cable Green WDO Output Wiegand data 0 signal Wiegand White WD1 Output Wiegand data 1 signal connection Black GND Ground cable Yellow TXD Send RS232 and receive the KR300 Usre Manual RS232 opponent s RXD connection Blue RXD Receive RS232 and receive the opponent s TXD Black GND Ground cable Red light Brown The control cable of red light which is off when low level and on when high level Green light Orange The control cable of green light which is on when low level and off when high level Buzzer Grey The control cable of buzzer which will buzz when low level and stop buzzing when high level Note The black Ground cable is in common in this table 3 Connection with access controller KR300 as a card reader it can not work by itself only can connect with the access controller or access control device to provide a front end to identify cards As below shown when connection please refer to connection terminal definitions KR300 User Manual Connec
8. tion terminal of access control device BEEP Grey GLED oe RLED Z IND 0 we IND 1 k a L GND Bue 12V RXD TXD 3 1 RS232 Communication RS232 Communication can be used to connect the computer to set the parameters of card reader by the control system of Wiegand reader and can not be used to connect the access control software in PC to enroll cards etc operations The detailed operation about card enrollment please refer to the corresponding document of access control device Note When ID cards in card reading area the reader can output the ID card numbers through Wiegand when Mifare card is in card reading area the reader can output the card number through Wiegand and can output four byte card number through RS232 at the same time And more the card reader will enter into the bidirectional RS232 communication status automatically In reverse if no Mifare card is in card reading area the reader can not do RS232 communication which is only effective for Mifare cards KR300 Usre Manual 3 2 Wiegand communication KR300 card reader can provide a standard or self defined Wiegand signal for access controller The connection method is the same as the other card readers Time sequence diagram of Wiegand code l 1 i O status wave 1 DATAI E i 1 1 DATAO I I 50us lms i 1 status wave DATA1 I DATAO i i 50us ims I I 1 1 _ 1 i KR300 User
Download Pdf Manuals
Related Search