Tech Note: Tracking - Livewire Connections Ltd
Contents
1. yes No APN C Common SIM default C Network assigned C User defined EGAN INMARSAT COM POSITION REPORTS Report type Com pressed Extended ECEF INTERVAL REPORT Status Enabled Disabled Report each fo p hh mm DISTANCE REPORT Status C Enabled Disabled When moved cid meters Max one report per E TE hhtmm Appl Y c ancel i 6 Under Interval report select Enabled or Disabled and type in the interval between the reports 7 Under Distance report select Enabled or Disabled and type in the following e When moved Enter the distance the vehicle should be moved before sending a report e Max one report per Enter the minimum time that should pass between two reports Example The distance is set to 10000 m and the time is set to 15 minutes The EXPLORER system has moved 10000 m since last report but only 10 minutes have passed A report will not be sent until the 15 minutes have passed 8 Click Apply Thrane amp Thrane A S Lundtoftegaardsvej 93 D DK 2800 Kgs Lyngby Denmark T 45 39 55 88 00 F 45 39 55 88 88 info thrane com www thrane com Bank Danske Bank Comp reg 65 72 46 18 VAT DK 20 64 64 46 Page 2 of 5 Thrane amp Thrane Document number 95 134282 Thrane Tracking System TTS 5 0 3 gt a Zi er Tracking abject The Thrane Tracking Protocol TTP is based on UDP and designed to consume as little bandwidth as possible on the air interface while still mainta2. supports 32 64 128 176 and 256 kbps Streaming and BGAN X Stream from a minimum of 384 kbps up to approximately 450 kbps Thrane amp Thrane A S Lundtoftegaardsvej 93 D DK 2800 Kgs Lyngby Denmark T 45 39 55 88 00 F 45 39 55 88 88 info thrane com www thrane com Bank Danske Bank Comp reg 65 72 46 18 VAT DK 20 64 64 46 Page 4 of 5 Thrane amp Thrane Document number 95 134282 Switching between the usage modes When the terminal is restarted it always starts up in the usage mode that was selected before shutting down To change the usage mode in the IP Handset select BGAN gt Terminal usage Then select the usage mode and select Apply For further information see the user manual for the IP Handset To change the usage mode in the web interface select SETTINGS gt Terminal usage mode select the usage mode and click Apply e Standard on the move Normal EXPLORER 727 function e X Stream on the pause Extended function for use when the vehicle is Stationary In addition to the standard EXPLORER 727 functions it supports BGAN X Stream and extended coverage TERMINAL USAGE MODE Terminal usage mode Standard on the move Stream fon the pause The terminal will reboot when usage mode is changed Press Apply to restart terminal Apply Cancel Note When you change the usage mode the terminal restarts The X Stream on the pause mode is not available whilst on the move and
3. Thrane amp Thrane Document number 95 134282 Date Aug 2011 New features Tracking and Terminal Usage Mode BGAN X Subject The below is describing new features Tracking position reporting and Terminal usage mode Standard or X Stream and is including extracts from EXPLORER 727 User Manual Rev D Tracking The EXPLORER 325 727 amp FBB 250 500 systems can be used for tracking purposes You can set up the terminal to report its position to a server at certain time intervals or after moving a specified distance To use the tracking feature you must either set up a tracking server or get a tracking solution from your service provider The EXPLORER system must be set up to match this server Setting up Tracking The EXPLORER system can be used for tracking purposes You can set up the terminal to report to a server at certain time intervals or after moving a specified distance To set up tracking do as follows 1 Select SETTINGS gt Tracking 2 Type in the Server IP address Server port Client port and Encryption key for your server connection e IP address The IP address of the server that the EXPLORER terminal will report to e Server port Port number on the server Default number is 7474 e Client port Port number on the EXPLORER terminal Default number is 7475 e Encryption key A pre shared 128 bit key which must match on both the client and server side 3 To allow remote control of the trackin
4. g settings from the tracking server select Yes at Allow remote control This means the EXPLORER terminal will accept commands from the specified tracking server for example to change reporting intervals or start stop reporting 4 Select the APN to use for Tracking You have the following options e Common The APN is taken from the Common APN defined under SETTINGS gt Common Refer to Setting the common interface settings on page 76 e SIM default The APN is taken from the SIM card This is the recommended option unless you have special requirements e Network assigned The APN is assigned from the network e User defined Type in the APN APNs are provided from the Airtime Provider Thrane amp Thrane A S Lundtoftegaardsvej 93 D DK 2800 Kgs Lyngby Denmark T 45 39 55 88 00 F 45 39 55 88 88 info thrane com www thrane com Bank Danske Bank Comp reg 65 72 46 18 VAT DK 20 64 64 46 Page 1 of 5 Thrane amp Thrane Document number 95 134282 5 Under Position reports select the report type you want to use e Compressed Only latitude and longitude are reported e Extended Apart from latitude and longitude heading and altitude are also included e ECEF The same information as Extended but position and speed data are 3D ECEF coordinates Example SERVER CONNECTION Server IP address zo IE fao Fa Server port 474 Chent port 475 Encrypton key 12345676912345676912345678912345 Allow remote control
5. ining all necessary data and a fair level of security Message encryption Since the TIG Tracking Internet Gateway can be placed anywhere on the internet it is preferable to have some sort of encryption of the messages between the UT user Terminal and the TIG For that purpose AES has been chosen with a block size of 128 bits Encryption will be done using a pre shared key which is entered by the user The key must be 128 bits long UDP ports The administrator of the TIG must choose an UDP port that the TOB Tracking Object can connect to This port value must be configured on the TOB When the TOB sends the register message it must use the same port number as source port as it will use to listen for incoming messages from the TIG The TIG must send all messages to the TOB to the source port number of the register message The following default port numbers has been defined 7475 7474 For more details please contact Thrane amp Thrane GTAC via extranet eSupport at http extranet thrane com Support Technical 20Support aspx Thrane amp Thrane A S Lundtoftegaardsvej 93 D DK 2800 Kgs Lyngby Denmark T 45 39 55 88 00 F 45 39 55 88 88 info thrane com www thrane com Bank Danske Bank Comp reg 65 72 46 18 VAT DK 20 64 64 46 Page 3 of 5 Thrane amp Thrane Document number 95 134282 EXPLORER 727 Terminal usage modes Software release ver 1 14 enables the terminal to operate in two different modes A
6. standard on the move mode where the terminal signs on to the BGAN network as a Class 10 vehicular terminal and a X Stream mode on the pause where the terminal signs on as a Class 1 terminal such as the EXPLORER 700 Standard on the move mode This is the normal mode of the EXPLORER 727 where all the usual EXPLORER 727 services are available whether or not the terminal is moving X Stream on the pause mode The X Stream on the pause mode can only be used when the terminal is not moving In the X Stream on the pause mode you can use the Inmarsat BGAN X Stream service and extend coverage to the entire BGAN coverage area for all available services For details see below Standard Data 432kbps 492 kbps With the BGAN X Stream service included in the subscription Up to approximately 450 kbps Streaming Data Up to 256 kbps BGAN X Stream service not included in subscription Up to 256 kbps Note 256 kbps is only supported Full coverage area for all subscribed from 45 degrees elevation and services inwards ISDN UDI RDI 64 56 kbps 64 56 kbps Note ISDN UDI RDI is only Full coverage area for all subscribed supported from 20 degrees elevation services and inwards Note the term Standard mode is not related to the term Standard background connection In Standard on the move mode the EXPLORER 727 system supports 32 64 128 and 256 kbps Streaming In X Stream on the pause mode the system
7. the terminal automatically stops transmitting with the loss of all existing connections if X Stream on the pause mode is active when the vehicle is moving Global Technical Assistance Centre Thrane amp Thrane A S Thrane amp Thrane A S Lundtoftegaardsvej 93 D DK 2800 Kgs Lyngby Denmark T 45 39 55 88 00 F 45 39 55 88 88 info thrane com www thrane com Bank Danske Bank Comp reg 65 72 46 18 VAT DK 20 64 64 46 Page 5of5 Author Date Checked Date Approved Date
Download Pdf Manuals
Related Search