LD-100-RS / LD-200-RS
Contents
1. 100 RS LD 200 RS is first turned on it will display a count of 1 or it will display the number from the previous count You can reset the Label Counter to zero 0 by pressing the R Reset Button 5 Thread the label web between the Stripper Bar and the round Guide Rod directly above it See the Label Threading Path illustration 6 Pull the label web under or over the round Web Guide and slide the width adjusters to the width of the web 7 Loop the web UNDER the Wire Bail on the Take Up Shaft as shown in the ene A FOR YOUR SAFETY 8 Slightly loosen the Label Sensor Lock Knob until you can just rotate the Sensor Switch off device before removing the bail2. FLANGES Set of e The ambient light of the working area needs to be sufficient to avoid any risk two Flanges These Flanges are recommended for e The dispenser can be used in ambient temperatures of 2 C to 40 C narrow or loosely wound labels that may have a e For operators working long hours on the machine it is recommended to wear glasses tendency to fall off the roll protecting from the light e g light sunglasses e All measures have been taken to minimise risks of injuries with the take up shaft but the operator has to be careful when manipulating the bail e Connection of the machine to the power source must respect local and European legislations Label Roll Holder SET UP AND USE Label Threading Path 1 Make sure the Power Switch is in the OFF position OPTIONAL LABEL COUNTER The optional Label Counter will add one count to the displayed number for each label that is dispensed This Option is available only factory installed in 2 Set your LD 100 RS or LD 200 RS in place and plug the cord from the Power Supply Module into the Power Input Jack on the rear of the Unit 3 Connect the Power Supply Module to a suitable power source 4 Place your roll of labels on the Label Roll Holder amp slide the Roll Edge Guide s to the width of your label web The Label Web can be positioned from side to side as EPI 7 difi new Units required to ensure that the label lines up with the reflective Sensor When the LD
3. MAINTENANCE Keep the Label Sensor and Stripper Bar clean following instructions page 1 Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders ayeas Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distribut
4. Roll Weight 4 5 Kg Max Label Roll Size 220 mm diameter 300 mm with LD DE Power Supply Input 220 240VAC 50 60Hz Output 11VAC 2 5A e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e Point the sensor up so it is pointing at the bottom of the Stripper Bar Place the Power Switch in the LOW position Slowly rotate the Sensor down until the label A begins to advance Continue to rotate the Sensor slowly until the desired label WARNING length is protruding Retighten the Lock Knob securely This Product is for indoor use only Not for use in wet locations 9 Use HIGH or LOW Switch setting to select the desired speed 10 IMPORTANT Pull labels UP when removing them If excess dust or dirt IMPORTANT INFORMATION accumulates on the Label Sensor Eye the a Dispenser may not sense labels correctly Use a cloth or paper towel dampened with water to gently This product is a label dispenser It is only to be used to dispense labels of the cece mis y p clean the Label Sensor recommended dimensions and weight in an indoor dry environment e The machine has to be unplugged before any manipulation e The machine is to be used on a flat surface if the surface is not flat it is to be fixed HEBomey tee any chemicals pik INe Sensor using the holes in the base plate 12 Optional Flanges for the inside and outside of the e Do not leave the power cable in a passageway label roll are available Order LD
5. or you bought the product from The customer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmateeurope com LABELMATE User_LD RS CE 01 13 Original user manual LD 100 RS LD 200 RS Powered Label Dispenser e High Low Speed Select e Adjustable Label Sensor Not for Transparent or Black Labels Remove all parts from the shipping container and verify contents PACKAGE CONTENTS e User Manual this document e Label Dispenser Unit e Power Supply Module Retain the Shipping Container and Packaging for Storage and Transport VERY IMPORTANT e Keep Label Sensor Eye clean Wipe with a soft cloth occasionally Be careful not to damage the sensor Do not use any chemical on the Sensor e Keep Tape Stripper Bar and Web Guide Bars clean Use isopropyl alcohol or Goo Gone to clean adhesive residue from parts Adhesive build up can cause malfunction and damage to your unit SPECIFICATIONS Weight of the machine 5 kg Max Label
Download Pdf Manuals
Related Search