DRG700 (version 2) Quick Installation Guide
Contents
1. adapter to the DRG700 and connect the adapter to a power socket Result The LED first flashes green When the booting process is completed the LED will be solid green Note The complete start up sequence may take 2 3 minutes Step 5 Connecting your computer Connect your computer to one of the Ethernet LAN ports on the DRG700 using an Ethernet cable with a RJ 45 connector Result The LAN port LED is on provided that the computer is on Step 6 Connecting your telephone This step is only relevant if the DRG700 has telephony ports Connect a standard telephone handset a telephony port using a RJ 11 cable Result The or LED is on if voice is enabled and operating correctly You should hear a dialtone if you pick up the handset Step 7 Connecting your analog television This step is only relevant if the DRG700 has a CATV connector Connect your television to the CATV connector using a coaxial cable with a male F connector Result The Q LED is on if CATV is enabled and operating correctly You may need to retune your television if required for the CATV service 3 NETWORK SETUP Step 1 Step 3 Open your web browser and check if your Internet Open your web browser and check if the network connection is working If your connection is working conne2. DRG 00 Quick Installation Guide Cs E NJ This guide applies to all DRG700 models CONTENTS ils DRG700 OvervieW eeeeeeeeeeeeeeeeee 2 2 installation 4 3 Network S tuDP eseeeeeeeeeeeeeeeeees 7 4 Wireless Setup 8 5 Configuring your DRG700 9 6 Troubleshooting ceeeeeseeesereeees 10 1 DRG 7O0O0 OVERVIEW User interfaces Interface Description Power port 2 Ethernet LAN ports USB 2 0 port Telephony ports CATV connector Reset button WPS button N DO uw A WN Note Depending on your specific product type port configuration may differ J E T Cleaning instructions Your DRG700 product may be cleaned using a soft dry cloth For areas of persistent dirt a damp cloth may be used with mild detergent Product and LED logos may be damaged by using aggressive cleaning products or ethanol based cleaners if in doubt do not clean near these logos Under no circumstances allow water or cleaning fluid to ingress the product as this may cause permanent damage and prevent correct operation Status feedback LEDS LED LAN ports Activity On green On red Blink green Off On Off On green On red Off On Off On Off On Blink Off On green On orange Blink Description Power on Error Booting Power off WAN link active WAN link ina
3. abled Please contact your service provider if a CATV signal is expected CATV is enabled but no signal is detected Please contact your service provider if a CATV signal is expected Voice functionality is not enabled Please contact your service provider if voice functionality is expected Please check in the web interface whether wireless functionality is enabled If the problem persists please contact your service provider Check if the physical connection between the DRG700 and your computer is correct Europe EU Declaration of Conformity CEO Hereby Genexis BV declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC DN gt lt i Copyright Genexis BV 2014 rev 1
4. ction is working If your connection is not you may skip step 2 and 3 working refer to the Troubleshooting section on page 11 Step 2 The following instructions are only for Windows Windows 7 Windows 8 For network setup internet Protocol Version 4 TCP IPvA Properties eax instructions on other operating systems please consult the user manual General Alternate Configuration 1 Select Start gt Control Panel 2 In the Network and Internet section click View for the appropriate IP settings Network Status and Tasks 3 Open the panel for network connections Obtain an IP address automatically For Windows Vista Click Manage network Use the following IP address connections at the top left hand corner For Windows 7 Click Change adapter settings at the top left hand corner 4 Identify the connected network card right click l the corresponding Local Area Connection and select Properties in the context menu Obtain DNS server address automatically 5 Select Internet Protocol Version 4 TCP IPv4 from the list and click Properties 6 Select Obtain an IP address automatically and Obtain DNS server address automatically 7 Click OK and close the window Use the following DNS server addresses 4 WIRELESS SETUP This section is only relevant if wireless functionality is available on your DRG7OO The following instructions are only for Windows 7 Windows 8 For wi
5. ctive CATV on signal received CATV on no signal received CATV disabled Phone line 1 active Phone line 1 inactive Phone line 2 active Phone line 2 inactive WLAN enabled WPS active WLAN disabled Link operating at 1000 Mbps Link operating at 100 or 10 Mbps Activity Reset button Function Action Restart To restart DRG700 without erasing the saved configuration 1 Press the button for less than 5 seconds 2 Release the button Factory To restart DRG700 with all configura reset tion data cleared and factory settings restored 1 Press the button for more than 5 seconds 2 Release the button WPS button This button is used to automatically connect a WPS enabled wireless client to the DRG700 For details about the connection procedure see Wireless Setup on page 8 2 INSTALLATION Step 1 Preparing the DRG FTU Step 3 Mounting the DRG700 on the DRG FTU Remove the dust cover from the DRG FTU Place the DRG700 on the FTU in such as way that the tabs on side of DRG700 are aligned with the cutouts on the FTU 2 Gently slide the DRG700 upwards until the fiber connectors connect firmly with the FTU woagnasr Step 2 Preparing the DRG700 Remove the dust covers for the fiber connectors on the DRG700 ecaanor Step 4 Powering the DRG700 Connect the 12V plug of the supplied
6. reless setup instructions on other operating systems please consult the user manual Wireless setup using WPA encryption key Step 1 Click the network icon in the notification area of the taskbar For example Customize ae fa call 1 47 200 Step 2 Select your network SSID and click Connect The SSID is the name of the wireless network Step 3 Enter your WPA key and click OK The WPA key is the password needed for your secured wireless network Note You can find the default SSID and the WPA key on a label shipped with the unit They are also printed on the label on the back of the DRG700 You can change the SSID and the WPA key when you configure the DRG700 Wireless setup using WPS Step 1 Click the network icon in the notification area of the taskbar Step 2 Select your network SSID and click Connect Step 3 Press the WPS button on the DRG The DRG700 automatically connects to the computer The connection is established and is displayed as Connected in the network list Toggling WLAN status Press the WPS button for gt 5 seconds and release it All user defined WLAN interfaces are toggled on off Status is indicated by WLAN LED 5 CONFIGURING YOUR DRG700 It is only advised for advanced users to change the configuration as doing this might interrupt your connection By default the router is configured properly for most home networks Note For information abou
7. t how to reset the router to the factory default settings see Reset button on page 3 Requirements The configuration program has been tested on the following browsers Safari version 5 or later Firefox version 10 or later Internet Explorer version 7 0 or later Google Chrome The browser must support Javascript Step 1 Launch the web browser on your computer and enter http router in the address bar The router s default IP address is 192 168 1 254 Step 2 Log in as admin using the default password admin It is strongly advised to change the password after you logged in for the first time Step 3 Configure the router to the desired configuration Read the help text for additional information about the settings 6 TROUBLESHOOTING Issue Y LED is off Y Red LED is on lt gt LED is off Q LED is off Q Red LED is on GS _ LED is off LED is off Web interface is not reachable Action Make sure you have connected the DRG700 to a working power outlet using the adapter shipped along with the DRG700 If the LED remains off please contact your service provider System error Disconnect the power from the DRG700 and restart DRG700 If the problem persists please contact your service provider No uplink Power down the device wait for 1 minute then power the de vice back on If the problem persists please contact your service provider CATV is dis
Download Pdf Manuals
Related Search