Home

PG-FPL2 Flash Memory Programmer UM

1. Load lt 2 gt Select a program file to be written to the target device then click Open Figure 5 7 After Loading File 15 x File Device View Help PAW s 22 FlashOpennine Flash Open OK gt OOMMAND Device Setup PRM File Read OK Parameter file FoF Ose Device Mame gt gt COMMAND LoadFile Open Name 78F9222 prm Success read HEX file Format 0413 ES Et Version E1 00b Processor Wer 0300 Name FPL2_TEST HEX Date F004 03 23 00 51 20 Chksum BOOTH Area OOO0000h O00F F Fh Success read HEX file is displayed Connection to device Port UWART cho Parameters are updated Speed 115200 Bu Freg H PQ Ready am User s Manual U17307EJ2V0UM 53 54 CHAPTER 5 USAGE EXAMPLE 7 Autoprocedure EPV command execution Select Device gt Autoprocedure EPV from the menu bar When the Autoprocedure EPV command is executed Erase gt Program are executed sequentially for the 1PD78F9222 In this example Blank check before Erase and Checksum after Program are checked So blank check is performed before the execution of the Autoprocedure EPV command and checksum is performed after the execution of the Autoprocedure EPV command Figure 5 8 After EPV Execution Eile Device View Help KE ya En 220 MM AND 4utoProceduretEpy A Flash Blank Check ine not blank then erase D
2. Remark The recommended receptacle connect that can be used with the FP4 connector is 8516 4500SC made by Sumitomo 3M 58 Users Manual U17307EJ2VOUM CHAPTER 6 CONNECTORS AND CABLES 6 6 List of Interface Connections Table 6 6 List of Interface Connections Signal lt 1 gt Target Cable lt 2 gt Tip of Target Cable lt 3 gt Target Connector lt 4 gt FP4 Connector Km E 4468 oGND EE IC E Figure 6 6 Target Interface 2 gt 3 gt 4 gt cin NECE Ta rget W lt PO FPL2 pr for 78K0S Kx1 Power Stat Kg PG FPL2 Target cable FPL2 FA User s Manual U17307EJ2VOUM 59 CHAPTER 7 NOTES ON TARGET SYSTEMS This chapter explains the basic notes on the target system for rewriting the flash memory in the microcontroller using the FPL2 CPU Pin Design Proposal RESET Do not connect the RESET signal generator on the target system to the RESET signal of the FPL2 Otherwise a signal conflict will occur To avoid the conflict isolate the RESET signal generator from the RESET signal of the FPL2 Do not generate RESET while the FPL2 is connected This must be especially noted in a system that uses an external watchdog timer Connect the RESET signal of the FPL2 at a point where the status of the programmer RESET signal and that of the CPU RESET pin are the same Correct connection Avoid the following RESET signal connection e Connection to a point where the target CPU RESET rise time is slower tha
3. Area Connection to device UART cho 115200 Status bar y User s Manual U17307EJ2VOUM 35 CHAPTER 4 OPERATION USING GUI SOFTWARE This window consists of the following items Menu bar displayed at the top Displays menu items executable by the FPL2 Toolbar displayed under the menu bar Displays frequently used commands as icons Action log window displayed under the toolbar Displays an FPL2 action log Programmer parameter window Displays programming parameter settings displayed to the right of the action log window Status bar Displays status 4 3 Toolbar The toolbar contains buttons to start the most important procedures of the FPL2 Table 4 1 Toolbar Buttons Device Setup button File Load button Device Blank check button Device Erase button Device Program button Device Erase Autoprocedure EPV button 4 4 Menus Depending on the actual device status or device type some menu items may be enabled or disabled 4 4 1 File menu After clicking the File menu the following pull down menu is displayed Commands related to file operation appear here 36 Users Manual U17307EJ2VOUM CHAPTER 4 OPERATION USING GUI SOFTWAR Figure 4 2 File Menu File Device Y Load gt gt FlashOpennine ash Open OF 1 Load command Ca The Load command allows you to select a program file The selected program fil
4. Figure 4 4 Device Menu Pre FPL2 File Device View Help if Blank Check JE Eraze q Program E Verilw Security Check sum AutoprocedurelE Pd signature read Setup 1 Blank Check command 38 2 3 d The Blank Check command initiates a blank check of the target device connected to the FPL2 If a the flash memory of the target device is erased the blank check terminates successfully If the flash memory is not completely erased not blank is displayed Erase the flash memory of the target device before starting programming Erase command cc The Erase command initiates the erase procedure for the target device connected to the FPL2 a While erasing the contents in the flash memory is in progress the progress is displayed in the action log window indicating the operation of the programmer The Blank Check command that is executed before the Erase command is executed in accordance with the setting of Command options on the Advance tab of the Device gt Setup menu After completing the Erase command the GUI software displays the target device command execution result Caution During an erase operation the Status LED is not turned on Do not disconnect the target cable and USB cable until the GUI software displays Erase finished Otherwise the target device may be damaged Program command r The Program command transmits the specified user program and writes them to the flash m
5. Starting UP GUSWA E 35 O MOD e 36 4A TE 36 ya Se kl Rn EE 36 BA MEI Nun E EE 38 443 MEW MEN Ut let a lt a do cl dos 46 AAA Heip MSN psss t ace are nel corno decena 47 4 5 Programmer Parameter Window ccccccesssessesseeeeenseeeenseeeeeenseeeeeaseeeeenseeenoseeeeoenseeeoenseeesonas 48 CHAPTER 5 USAGE EXAMPLE cota AA A da A ahaaa 49 CHAPTER 6 CONNECTORS AND CABLES oncccccccnncconcconancnnncnnnnnnnncnanacnnnrnnnnrnnnn cnn nrrnanarnnnrnnanrnanarnanans 55 5 1 USB Connector LEE Ruin 55 6 2 Target Cable Connector FPL2 00cooccccccnnncccconncccocnccconcnnccnnnncnennnnnnnnnannnrennnnnrrnnannrrnnnnnnrnnnananennn 56 8 User s Manual U17307EJ2VOUM 6 3 Target Cable ee HEEN 57 6 4 Target Connector FREE iii dianas 57 6 55 FPA Connector ER ee 58 6 6 LEIStof InieriaGe CONNECHONS ee ee 59 CHAPTER 7 NOTES ON TARGET SYSTEMS ccccsssssseccccsnsssecceccnasseececnnsseececnnsseseeennasseseess 60 CHAPTER 8 CIRCUIT DIAGRAM Sica a 63 CHAPTER 9 TROUBLESHOOTIN Garita nenne 65 9 1 Trouble During Ee 65 9 2 Trouble During Operation Main Unit sssmmssmunsnumanu manana namana nuana manana nuananunanunaananananunuaaza 66 9 3 Trouble During Operation COMMUNICATION ooncccnnnncccnnnnccconcnncennnncncnnnnnnnenannnrenannnnrnnannnnenons 66 APPENDIX A PRODUCT SPECIFICATIONS secccssnsseeccccsnssseccecnnsseeccecnnassescecnnnsseseecnnsseeseesaass 68 AT Hardware Specifications ii
6. Windows Installer Package Cabinet File Application Configuration Settings Configuration Settings Double click User s Manual U17307EJ2VOUM Date Modified 6 30 2004 4 19 PM 6 30 2004 4 19 PM 518 2004 11 55 AM 518 2004 11 55 AM 417 2004 3 52 PM 8 17 2004 3 52 PM 8 17 2004 3 52 PM 312 2002 12 45 AM 3 11 2002 10 06 AM 4 10 2003 3 03 AM 8 17 2004 2 48 PM 4117 2004 3 52 PM 8 17 2004 3 52 PM 4117 2004 3 52 PM 8 17 2004 3 52 PM 417 2004 2 48 PM CHAPTER 3 SOFTWARE INSTALLATION 4 Select a language to be used for installation English in this example then click OK Figure 3 28 Setup Language Selection Choose Setup Language Select language 5 Select Remove then click Next gt Figure 3 29 Program Modification InstallShield Wizard Welcome Modify repair or remove the program si e Welcome to the PG FPL2 47 00 Setup Maintenance program Click one of the options below Modify Select new program features to add or select currently installed features to remove Pree rete Select Remove Cancel 6 Click to start uninstallation Figure 3 30 Confirmation of File Deletion Contirm Uninstall Do you want to completely remove the selected application and all of tts features Cancel User s Manual U17307EJ2VOUM 33 CHAPTER 3 SOFTWARE INSTALLATION 7 When uninstallation of the GUI software is complete the screen shown below appears Click to
7. 2 Disconnect the FPL2 FA from the target system a When the FPL2 is connected with the target system by using the FPL2 FA lt 1 gt Turn off the power to the target system When the MODE switch is set to 3 V power is supplied from the FPL2 so this step is not required lt 2 gt Disconnect the FPL2 FA from the target system Caution When the MODE switch is set to 3 V the FPL2 outputs power at all times Be sure to disconnect the FP4 connector from the target system before disconnecting the target device b When the FPL2 is connected with the target system without using the FPL2 FA lt 1 gt Turned off the power to the target system When the MODE switch is set to 3 V power is supplied from the FPL2 so this step is not required lt 2 gt Disconnect the tips of the target cables marked 1 RESET 3 DGCLK and 4 DGDATA from the target system Caution Be sure to disconnect the target cables in this order If the target cables are disconnected in an incorrect order the target system or the FPL2 may be damaged lt 3 gt Disconnect the tip of the target cable marked 2 Vpp from the target system lt 4 gt Disconnect the tip of the target cable marked 0 GND from the target system 3 Disconnect the USB cable from the host machine Make sure that the Power LED is turned off 4 Disconnect the USB cable from the FPL2 16 Users Manual U17307EJ2VOUM CHAPTER 3 SOFTWARE INSTALLATION 3 1 GUI Software Installation T
8. Search Location Specification Windows 98 Add New Hardware Wizard Windows will search for new drivers in its diver database on Your hard drive and in any of the following selected locations Click Next to start the search T Floppy disk drives CD ROM drive Microsoft Windows Update vw Dpechu a location C Program Ple NECT ools32binsPG FPLA4DRAl Cancel Enter C Program Files NEC Tools32 bin PG FPL2 DRIVER Remark If the installation destination folder is changed for GUI software installation enter new foldenbin PG FPL2 DRIVER 24 User s Manual U17307EJ2VOUM CHAPTER 3 SOFTWARE INSTALLATION 4 The window below is displayed Confirm the contents and click Next gt Figure 3 15 Checking Driver to Be Installed Windows 98 5 When installation of the USB driver is complete the screen shown below appears Click to complete installation Figure 3 16 Completion of Installation Windows 98 Add New Hardware Wizard User s Manual U17307EJ2VOUM 25 CHAPTER 3 SOFTWARE INSTALLATION 3 2 2 Installation in Windows 2000 1 When the FPL2 is connected with the host machine the FPL2 is recognized by Plug and Play and the wizard for finding new hardware is started Click Next gt Figure 3 17 Found New Hardware Wizard Windows 2000 Found New Hardware Wizard SA EE Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for
9. UX60A MB 5ST made by Hirose Electric Caution The recommended USB cable Mini B type for connection with the host machine is the USB cable included with the QB 78KOSKX1 MINI User s Manual U17307EJ2VOUM 55 CHAPTER 6 CONNECTORS AND CABLES 6 2 Target Cable Connector FPL2 Figure 6 2 Pin Layout of Target Connector Table 6 2 Pin Assignment of Target Cable Connector e ae Oo foe Connector part number DF3A 8P 2DSA made by Hirose Electric 56 Users Manual U17307EJ2VOUM CHAPTER 6 CONNECTORS AND CABLES 6 3 Target Cable Specifications Figure 6 3 External View of Target Cable Table 6 3 Pin Assignment of Target Cable Cable Specification Display Specification D wen mee In Jew Supported header pin specification 0 635 x 0 635 mm length 6 mm Remark The recommended header pin that can be used with the target cable is FFC 5AMEP1 made by Honda Tsushin Kogyo 6 4 Target Connector FPL2 FA Figure 6 4 External View of Target Connector Target Connector FPL2 FA Signal Name ICI CT Connector part number FFC 5AMEP1 made by Honda Tsushin Kogyo User s Manual U17307EJ2VOUM 57 CHAPTER 6 CONNECTORS AND CABLES 6 5 FP4 Connector FPL2 FA Figure 6 5 External View of FP4 Connector 15 16 Table 6 5 Pin Assignment of FP4 Connector FP4 Connector FPL2 FA Signal Name Inside Parentheses FP4 a Name Tu ee Connector part number 8516 4500SC made by Sumitomo 3M
10. User s Manual U17307EJ2VOUM 49 CHAPTER 5 USAGE EXAMPLE 4 Connecting and starting the system lt 1 gt Set the MODE switch to 3 V lt 2 gt Connect the FPL2 with the host machine via the USB cable lt 3 gt Check that the Power LED is turned on lt 4 gt Check that the power to the target system is not turned on then connect the FPL2 with the target system via the target cable lt 5 gt Start the GUI software Figure 5 1 GUI Software Main Window loj x File Device Wiew Help Pa ler N gt gt FlashOpenning Flash O Se OK Parameter file Device Mame Mame Format Version Processor Ver Mame Date Ghksum rea Connection to device UART cho 115200 5 Setting the programming environment lt 1 gt Select Device Setup from the menu bar lt 2 gt The Device Setup window for device setup is activated Figure 5 2 Device Setup Window Standard Tab Es Device Setup x Standard Advance Parameter file PAM File read Communication interlace to device Port LART ch0 Speed 115200 bps Operation Mode Chip C Block End sl Area T Show Addres Supply oscillator Frequency Je MHz 1 00 Multiply rate 50 Users Manual U17307EJ2VOUM CHAPTER 5 USAGE EXAMPLE lt 3 gt Click PRM File Read to open the parameter file selection window In this case select the parameter file for the 4PD78F9222 then click Open Figure 5 3 Pa
11. box is checked the Program command becomes invalid as does the Erase command in all the blocks of the flash memory selected under Operation Mode in the Standard Setup menu The Erase command for the entire flash memory area is valid This setting is cleared by the Erase command when Chip was selected under the Operation Mode User s Manual U17307EJ2VOUM 45 CHAPTER 4 OPERATION USING GUI SOFTWARE Caution The following is the correspondence between the Erase and Program commands when the security functions of a 78KOS Kx1 Series microcontroller are valid ee CHIP Erase Command Block Erase Command Program Command Note Since the Erase command is invalid the data that differs from the data already written in the flash memory cannot be written 4 4 3 View menu Clicking the View menu displays the following pull down menu This menu consists of commands for commands for setting whether to display the toolbar and status bar Figure 4 15 View Menu File Device Device View View Help Toolbar J9 Gm e status Bar 22 FlashOpennine Flash Open OK 1 Toolbar command Checking the Toolbar command displays the toolbar Unchecking the command hides the toolbar 2 Status Bar command Checking the Status Bar command displays the status bar Unchecking the command hides the status bar 46 Users Manual U17307EJ2VOUM CHAPTER 4 OPERATION USING GUI SOFTWAR 4 4 4 Help menu Clicking
12. cable to X2 of target device Cause The power may not be supplied to the target device correctly Action lt 1 gt Check that the power is supplied in the target system lt 2 gt If the power is supplied from the FPL2 check if the setting of the MODE switch is correct Cause The PRM file selected in the Device Setup window may be incorrect Action Use a PRM file that matches the target device Refer to CHAPTER 4 OPERATION USING GUI SOFTWARE for information about PRM files Remark A parameter file prc for FlashPro3 is unusable 66 Users Manual U17307EJ2VOUM CHAPTER 9 TROUBLESHOOTING Cause The power supply capacity of the USB port of the personal computer may be low when the MODE switch is set to 3 V Action Try using another personal computer or supply power from the target system by setting the MODE switch to Target Cause Security may be set Action Check that security is not set The Status LED does not blink during erase operation In accordance with the specifications of the FPL2 the Status LED may not blink during erase operation To confirm the erasure status check the following message in the action log window of the GUI software Message during erase operation Flash Erasing Message for completion of erasure chip erase finish or all block erase finish Cause The power supply capacity of the USB port of the personal computer may be low when the MODE switch is set to 3 V Actio
13. in 1 Circumstances not covered by product guarantee User s Manual U17307EJ2VOUM Regional Information Some information contained in this document may vary from country to country Before using any NEC Electronics product in your application please contact the NEC Electronics office in your country to obtain a list of authorized representatives and distributors They will verify e Device availability e Ordering information e Product release schedule e Availability of related technical literature e Development environment specifications for example specifications for third party tools and components host computers power plugs AC supply voltages and so forth e Network requirements In addition trademarks registered trademarks export restrictions and other legal issues may also vary from country to country GLOBAL SUPPORT http www necel com en support support html NEC Electronics America Inc U S Santa Clara California Tel 408 588 6000 800 366 9782 NEC Electronics Europe GmbH Duesseldorf Germany Tel 0211 65030 e Sucursal en Espana Madrid Spain Tel 091 504 27 87 e Succursale Francaise V lizy Villacoublay France Tel 01 30 67 58 00 e Filiale Italiana Milano Italy Tel 02 66 75 41 e Branch The Netherlands Eindhoven The Netherlands Tel 040 244 58 45 e Tyskland Filial Taeby Sweden Tel 08 63 80 820 e United Kingdom Branch Milton Keynes UK Tel 01908 691 133 User
14. s Manual U17307EJ2VOUM 7 CONTENTS CHAPTER 1 OVERVIEW AI 10 Med GROANS EE 10 CHAPTER 2 HARDWARE INSTALLATION 0 cccccceeeesseecesecesseceseeenseeenseeensecessenasueoasecnsenenseneesenaeess 11 EN lt SYSTCMT Ee UE TE CN 11 O A AA aa aaa a aaa a E 11 2 3 System Configuration and Components ccceeeeseeesseeeeeeenseeeeeeeenseeeeeeenseeeseoeenseesseoeenseees 12 2 3 1 FPL2 display specifications connector and MODE switch settmges 12 202 E CONNEC E 13 o ARO EN E 13 20A WS COMME ION see Wa PA APO WA POA SA ULA WEE PU AA AE PEMA PEPO APO KU AAPA UA MAE AAA 13 2939 Eet ee EE 13 2 010 elle eidelen EE 14 2 3 7 Disconnection gier 16 CHAPTER 3 SOFTWARE INSTALLATION xeeeskeReEERKNEKNEEKR EES EKEEREKEER KEE KEE KEENEKEEREKEER KEE VEER NEEEK Een 17 3 1 GUESOPR Ware Instalati wa aa waa Mai aa 17 3 2 USB Driver Instalati n EE 23 3 2 1 Installation in Windows Oo Me ooncccccccccccncccnnccocnnconcnonnnncnnnnnnnnnnnnnnnnnnnnnonnnnnnnnnnnnrnnnnnnnnnnnnnnnnnenanens 23 322 Mstallationin VWWINGOWS 2000 RE 26 3 2 3 Installation in Windows AH 29 3 3 Confirmation of USB Driver Installation coonncccnnnccicnnncicoccnncccncnncnconcnnnnennnnnnenonnnnrnnnnnanenons 31 3 4 Unimstala OM a dad 32 SAA RIVE UNAS tala ON ed EE 32 2942 GUI Sotware Uninstall ten WEE 32 CHAPTER A OPERATION USING GUI SOFTWARE o ooccoccccccccnnccnnnncnnnncnnnccnnnrnnnncnnnncnanrnnnnrnanarnnannnanans 35 AT Tu e E de EE 35 42
15. the Help menu displays the following pull down menu Figure 4 16 Help Menu File Device View Help JE En About FPL2 gt FlashOpennine ash Open OK 1 About FPL2 command The About FPL2 command opens the following program entry window and indicates the version Clicking terminates the display Figure 4 17 About FPL2 Window About FPL i Pe SGM EREER EERE REREES mm qa oe be Se i pa ES P l TERES LE r i E User s Manual U17307EJ2VOUM 47 CHAPTER 4 OPERATION USING GUI SOFTWARE 4 5 Programmer Parameter Window 48 This window displays the settings of the programming parameters Figure 4 17 Programmer Parameter Window Parameter file Device Mame Hame Format Wersion Processor Wer Marne Date Ghkesun rea Connection to device UART ch Speed 115200 H m Parameter file Displays information about a parameter file updated and read after Setup command execution Load file Selects information about a program file updated and selected after Load command execution Connection to device Display information about the connection with the target device Remark Since the target device of the FPL2 is the 78K0S Kx1 this item is fixed so it cannot be changed Users Manual U17307EJ2VOUM CHAPTER 5 USAGE EXAMPLE This chapter explains a series of basic operations of the FPL2 with t
16. 02SC JUMPER Microcontroller User reset circuit OO Cautions 1 The FPL2 generally performs normally without pin connection 2 If the signals X1 X2 RESET used by the FPL2 are connected pull up or pull down referring to CHAPTER 8 CIRCUIT DIAGRAMS 3 Isolate the oscillator 4 Pin 3 and pin 5 DGDATA are functionally equivalent Pin 9 and pin 14 DGCLK are functionally equivalent Connect the respective pins 62 Users Manual U17307EJ2VOUM DD DO CHAPTER 8 CIRCUIT DIAGRAMS Figure 8 1 Circuit Diagram of FPL2 FA Main Unit 2516 45005 of j of A Li a FFE SAMEPR User s Manual U17307EJ2VOUM 63 id FA i 98 920A va 3 dd NSSTIZSLOL WHOL e uno ou T KI y Ma C DCH SCH ma g 99A SISSIES lt 0X1 C Ann as 9Z0 Agnes E 929 Ap 19 9auuos 879 d 0019 alqesjab1e SA 2027 48 EA FS 00 oda ital E Sp 9Z04 CO wIvd30 Bett H SA B ONE NAGELZSZOL em ZS ha mem e Al OR Le GI ve zy vn tren Coen za quncu 304 DIA e lt ZNS HIGOA Zid ONE U lt cc O E el O ec O 00 oc LLI H D lt L O Figure 8 2 Target Interface Block Li ans H INDO RI AGA ada N 88 9Z0A za e goat K EN P el Aino ano Y NI Le 5 99 e LINO asas zd en aan op R328 MOD MPa LINO 4 de Alen User s Manual U17307EJ2VOUM 64 CHAPTER 9 TROUBLESHOOTING 9 1 Trouble During Setup 1 When installing the driver the driver is not rec
17. 2 MB or more Host interface USB interface that enables communication based on USB Ver 1 1 or later File formats Program files can be used in Motorola HEX file format or Intel HEX file format 2 2 Package Contents Please verify that you have received all the parts listed in the package contents list included with the FPL2 package If any part is missing or seems to be damaged please contact an NEC Electronics sales representative or distributor User s Manual U17307EJ2VOUM 11 CHAPTER 2 HARDWARE INSTALLATION 2 3 System Configuration and Components The FPL2 system configuration is as given in the diagram below Figure 2 1 FPL2 System Configuration FA adapter DECH DKCH Ss ssessase UCL sseseseese Host machine ID78KOS QB Disk 9 gioooooooo o a Target cable Target system compatible with FP4 connector MODE D NEC fen WO b PG FPL2Z for TOSK USB cable Mini B type PG FPL2 Target system not compatible with FP4 connector Notes 1 Use the USB cable Mini B type included with the QB 78KOSKX1MINI 2 The FA adapter board is a product of Naito Densei Machida Mfg Co Ltd The FPL2 is connected to the host machine via the USB cable Mini B type The FPL2 is connected to the user system via the target cable For the detailed specifications of the target cable and connector refer
18. 2 and the user program are displayed and verified after execution of the Program and Autoprocedure EPV commands The value shown in this box differs from the value displayed in the parameter window in the main window OK is displayed if the values match and ERROR checksum does not match if the values do not match Security flag settings The lt Security flag settings gt dialog box is used to specify which security function is valid Figure 4 13 Device Setup Window Security Flag Settings security flag settings Disable Block Erase Disable Program Disable Chip Erase check box If this check box is checked the Erase command becomes invalid in the entire flash memory area of the target device At this time the warning message shown below is displayed Figure 4 14 Device Setup Window Disable Chip Erase Warning FPL X AN When Chip Erase is disabled chip cannot be erased and programmed any more E Cancel Caution Be aware that if the security flag is set in the target device neither erasing nor writing to the device can be enabled afterward Disable Block Erase check box If this check box is checked the Erase command becomes invalid in all the blocks of the flash memory selected under Operation Mode in the Standard Setup menu This setting is cleared by the Erase command when Chip was selected under Operation Mode Disable Program check box If this check
19. AA 68 AZ Dimensions EE 69 APPENDIX B WARRANTY AND SUPPORT ccc sscseeeesceesseeesecensseeeseeesaseeeeeooaaseeeseoeasseeeseoanneeeeeoonaas 72 ECH Warranty sida ii ii 72 B2 SUDDO ee 72 APPENDIX C REVISION HISTORY cccssssseeccccnnsseeccecnnsseececcnassccecnnasseseecneasseseecnnsseeseconasseecesenaseees 73 User s Manual U17307EJ2VOUM 9 CHAPTER 1 OVERVIEW The PG FPL2 is a tool that erases and writes programs on an NEC Electronics 78KOS Kx1 Series on chip flash memory single chip microcontroller on the target board or FA adapter board 1 1 Features The PG FPL2 is a compact flash memory programmer for an on chip flash memory microcontroller and is designed for development e The USB interface is available for connection with the host e The PG FPL2 allows on board programming without removing the target device from the target system e Only single wire UART interface is supported for data transfer to the target device e Device specific parameters required for programming can be read from the parameter file PRM file 10 Users Manual U17307EJ2VOUM CHAPTER 2 HARDWARE INSTALLATION 2 1 System Requirements Host PC A PC supporting Windows 98 Windows Me Windows 2000 or Windows XP is required to run the FPL2 in the graphical user interface GUI mode About 2 MB of free hard disk space is required to install the GUI software Host machine IBM PC AT or compatible CPU Pentium 100 MHz or more RAM 3
20. D SUPPORT B 1 Warranty This product including hardware and software is replaced free of charge in the case of an initial failure only No warranty is provided for failures other than initial failures B 2 Support No support is provided for this product Visit the following site to obtain the latest information about this product Site http www necel com micro ods eng 72 User s Manual U17307EJ2VOUM APPENDIX C REVISION HISTORY The revision history is shown below Applicable Chapter refers to the chapter in each version Second Addition of APPENDIX B WARRANTY AND SUPPORT APPENDIX B WARRANTY AND SUPPORT User s Manual U17307EJ2VOUM 73
21. OUM 29 CHAPTER 3 SOFTWARE INSTALLATION Figure 3 24 Search Method Windows XP lt 1 gt Check that Search for the best driver in these locations is selected Found New Hardware Wizard Please choose pour search and installation optic Search for the best driver in these locations Use the check bores below to limit or expand the default search which includes local paths and removable media The best driver found will be installed Search removable media floppy CD AOM Include this location in the search lt 2 gt Check Include this location in the search only O Don t search will choose the driver to install Choose this option td select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware lt 3 gt Enter C Program Files NEC Tools32 bin PG FPL2 DRIVER 3 When installation of the USB driver is complete the screen shown below appears Click to complete installation Figure 3 25 USB Driver Installation Completion Windows XP Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software hor O NEC Electronics lE PC Interface PG FPLZ Click Finish to close the wizard 30 User s Manual U17307EJ2VOUM CHAPTER 3 SOFTWARE INSTALLATION 3 3 Confirmation of USB Driver Installation After installing the two types of drivers check t
22. To our customers Old Company Name in Catalogs and Other Documents On April 1 2010 NEC Electronics Corporation merged with Renesas Technology Corporation and Renesas Electronics Corporation took over all the business of both companies Therefore although the old company name remains in this document it is a valid Renesas Electronics document We appreciate your understanding Renesas Electronics website http www renesas com April 1 2010 Renesas Electronics Corporation Issued by Renesas Electronics Corporation http www renesas com Send any inquiries to http www renesas com inquiry ENESAS 8 10 11 12 Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is granted
23. a hardware device To continue click Net 2 The window below is displayed Check that Search for a suitable driver is selected then click Next gt Figure 3 18 Search Method Windows 2000 Found New Hardware Wizard Install Hardware Device Drivers aa device driver ls a software program that enables a hardware device to work with an operating system This wizard will complete the installation for this device Check that Search for a USB Device suitable driver is selected A device driver is a software program that makes a hardware device work Windows needs driver tiles for pour new device To locate driwer files and complete the Installation click Mest at do you want the wizard to do Search for a suitable driver for my device recommended C Display a list of the known drivers for this device so that can choose a specific driver Back Cancel 26 User s Manual U17307EJ2VOUM CHAPTER 3 SOFTWARE INSTALLATION 3 Check the Specify a location check box only then click Next gt Figure 3 19 Driver File Location Windows 2000 Found New Hardware Wizard Locate Driver Files Where do you want Windows to search for driver files Search for driver files for the following hardware device USE Device Check that Specify a location only is checked e wizard searches for suitable drivers in its driver database on your computer and in any
24. ain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronic
25. ancel 6 When installation of the USB driver is complete the screen shown below appears Click to complete installation Figure 3 22 USB Driver Installation Completion Windows 2000 Found New Hardware Wizard Completing the Found New Hardware Wizard 7 NEC Electronics IE PC Interface PG ER A Windows has finished installing the software for this device To close this wizard click Finish Eancel 28 User s Manual U17307EJ2VOUM CHAPTER 3 SOFTWARE INSTALLATION 3 2 3 Installation in Windows XP 1 When the FPL2 is connected with the host machine the FPL2 is recognized by Plug and Play and the wizard for finding new hardware is started Check that Install from a list or specific is selected then click Next gt Figure 3 23 Found New Hardware Wizard Windows XP Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for USE Device 9 If your hardware came with an installation CD 32 or floppy disk insert it now Check that Install from a list or What do you want the wizard to do specific is selected Install the software automatically Recommended 2 Check that Search for the best driver in these locations is selected Check the Include this location in the search check box and enter C Program Files NEC Tools32 bin PG FPL2 DRIVER in the address bar then click Next gt User s Manual U17307EJ2V
26. complete uninstallation Figure 3 31 Completion of Maintenance InstallShield Wizard Maintenance Complete InstallShield Wizard has finished performing maintenance operations on HIER AV UU Cancel 34 User s Manual U17307EJ2VOUM CHAPTER 4 OPERATION USING GUI SOFTWARE 4 1 Introduction Before you start using the FPL2 download the parameter file for the target device PRM to the PRM folder lt Downloading the parameter file gt The PRM file is not part of the FPL2 software package It has to be downloaded from the following NEC Electronics website http www necel com micro ods eng index html website in English http www necel com micro ods jpn index html website in Japanese The PRM file downloaded from the NEC Electronics website must be copied into the sub directory lt FPL2 EXE installation path gt PRM which was created during GUI software setup see CHAPTER 3 SOFTWARE INSTALLATION 4 2 Starting up GUI Software e GUI software startup Select FPL2 EXE in the Start menu to start the FPL2 GUI software When the GUI software is started normally the following screen appears Figure 4 1 GUI Software Main Window Menu bar Ers WE la x Eile Device View Help KE l J i CH a re o Programmer parameter window L EN gt gt FlashOpennine 3 Flash Open OF arameter Tile Device Mame Name Format Version Processor Wer Name Action log window Date Chk sum
27. dows Installer Package 6 17 2004 3 52 PM Cl ProgaeLesbh 240KB Cabinet File 8117 2004 3 52 PM 220 KB Application 3117 2004 3 52 PM E D I 2 KD Configuration Settings 4117 2004 3 52 PM un nsk ini L ER Configuration Settings 3107 2004 2 46 PM Double click User s Manual U17307EJ2VOUM 17 CHAPTER 3 SOFTWARE INSTALLATION 4 Select a language to be used for installation English in this example then click OK Figure 3 2 Setup Language Selection Choose Setup Language E Select language 5 After selecting the language the window shown below is displayed Click to continue installation Figure 3 3 Installation Start InstallShield Wizard Welcome to the InstallShield Wizard for PG FPL2 1 00 This program will install the PG FPL2 V1 00 on your computer All of the NEC Electronics Microcomputer Development Tools should be closed before continuing the installation To continue click Next Cancel 18 User s Manual U17307EJ2VOUM CHAPTER 3 SOFTWARE INSTALLATION 6 The software License Agreement window appears Read the displayed license agreement carefully then click if you accept the agreement You need to accept the agreement before using the PG FPL2 If you do not accept the agreement click to terminate the installation of the software Figure 3 4 License Agreement Window InstallShield Wizard License Agreement Please read the following license agreement carefully Press
28. e FPL2 is connected After deletion Find New Hardware wizard may start At this time click Cancel 3 4 2 GUI software uninstallation The driver uninstallation program is contained in the CD ROM ID78KOS QB Disk included with the QB 78KOSKX1MINI package this program is used commonly as the installer Use the procedure below for driver uninstallation 1 When using Windows XP log on as the computer administrator When using Windows 2000 log on as the Administrator 2 Insert the CD ROM ID78K0S QB Disk included with the QB 78KOSKX1 MINI package into the CD ROM drive 3 Double click My Computer CD ROM PG FPL2 and SETUP in that order Double click setup exe in the SETUP folder Figure 3 27 SETUP Folder SETUP File Edit Ses ae Help Q taa WW gt Ka E Search K Folders Hab View Favorites Tools Name File and Folder Tasks Ka nechst ein Other Places Details 32 Size 4 KB 3 KB o KE o KE 45 KE 24 KE 5 KB 1 669 KE 1 730 KB 697 KE 1 KE 1 251 KB 240 KB 220 KE 2 KE 1 KE _necinst_j in_ 0 0409 ini 20041 Lini 1033 mst 1041 mst e Docume 1 cab Silinstmsia Axe linstmsiw exe A lsscripts Msi A necsetup ini lp FL msi LI Prograr 1 cab E setup exe ERD mm Sun st ini Type IN File IN File Configuration Settings Configuration Settings MST File MST File Cabinet File Application Application Windows Installer Package Configuration Settings
29. e will be programmed into the device s flash memory by executing the Program command or Autoprocedure EPV command Figure 4 3 HEX File Selection Window Look in E Po tple y Tl ex Driver Pirm File name Files of type Hex Files HEH sl Cancel A The most recently used directory from which a file has been loaded will be offered in this window as the default selection After loading the user program the checksum is calculated and the result is displayed in the programmer parameter window Open button Selects a user program as a program to be written to the target device Cancel button Closes the window without selecting a program 2 Quit command The Quit command terminates the FPL2 GUI software Clicking the button on the right side of the task bar also terminates the FPL2 GUI software User settings are saved in the FPL2 INI file so that the GUI software will start up next time with the same settings Note FPL2 INI is created in the Windows folder when Windows 98 Windows Me or Windows XP is used When Windows 2000 is used FPL2 INI is created in the Winnt folder Users Manual U17307EJ2VOUM 37 4 4 2 Clicking the Device menu displays the following pull down menu CHAPTER 4 OPERATION USING GUI SOFTWARE Device menu This pull down menu mainly consists of commands for programming the target device such as erase program and verify
30. ed from the FPL2 so this step is not required b When the FPL2 is connected with the target system without using the FPL2 FA lt 1 gt Disconnect the FPL2 FA from the target cable lt 2 gt Make sure that the power to the target system is not turned on Caution Make sure that the power to the target system is not turned on before connecting the target cable If the target cable is connected after the power to the target system is turned on the FPL2 may be damaged lt 3 gt Connect the tip of the target cable marked 0 GND to GND of the target system Caution Be sure to connect 0 GND at the beginning If connections are made in an incorrect order the FPL2 and target system may be damaged lt 4 gt Make sure that the power to the target system is not turned on User s Manual U17307EJ2VOUM 15 CHAPTER 2 HARDWARE INSTALLATION lt 5 gt Connect the tip of the target cable marked 2 Vpp to Voo of the target system Caution Be sure to make connections in the order from 0 GND to 2 Vpp to other signals If connections are made in an incorrect order the FPL2 and target system may be damaged lt 6 gt Connect the tips of other target cables to the target system lt 7 gt Turn on the power to the target system When the MODE switch is set to 3 V power is supplied from the FPL2 so this step is not required 2 3 7 Disconnection procedure 1 When communication with the target system ends terminate the GUI software
31. em may be damaged 2 When the MODE switch is set to 3 V power is supplied from the FPL2 the voltage output to the Voo pin when the FPL2 is connected with the host machine 3 Connect the target system with the FPL2 a When FPL2 is connected with a target system that has a 16 pin connector usable with the FP4 connector lt 1 gt Connect the tip of the target cable with the target connector of the FPL2 FA Connect the tip of the target cable with the target connector of the FPL2 FA so that the number marked on the tip of the target cable matches to the number marked on the FPL2 FA board Remark The FPL2 FA is connected with the target cable at shipment 14 Users Manual U17307EJ2VOUM Match the number Tip of target cable lt 2 gt Make sure that the power to the target system is not turned on Caution Make sure that the power to the target system is not turned on before connecting the target cable If the target cable is connected after the power to the target system is turned on the FPL2 may be damaged lt 3 gt Connect the FP4 connector with the connector installed in the target system Caution When the MODE switch is set to 3 V power is supplied from the FPL2 Voo is always output from the FP4 connector Be sure to remove the FP4 connector before inserting or removing a device in the target system lt 4 gt Be sure to turn on the power to the target system When the MODE switch is set to 3 V power is suppli
32. emory After execution of the Program command to display and verify the checksum values of the target device and the user program to detect a communication error of the user program while it is being transmitted set Command options on the Advance tab of the Device gt Setup menu Users Manual U17307EJ2VOUM 4 5 6 7 8 9 CHAPTER 4 OPERATION USING GUI SOFTWAR While programming is in progress the progress is displayed in the action log window indicating the operation of the programmer This progress indicates the progress of programming the target device as a percentage After completing the Program command the GUI software displays the target device command execution result Verify command This command is not supported Security command The Security command initiates the programming of the security flag of the target device connected to the FPL2 Set Security flag settings on the Advance tab of the Device gt Setup menu CheckSum command The CheckSum command initiates the displaying and verifying of the checksum values of the target device connected to the FPL2 and the user program OK is displayed if the values match and ERROR checksum does not match if the values do not match Autoprocedure EPV menu ES The Autoprocedure EPV command sequentially executes the Erase and Program commands explained above After execution of the Au
33. esas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers office equ
34. evice Name faFO22 IS Name T8FO222 prm h tinish chip erase finish SEN See 0413 Gest A K Version E1 00b ash Frogramming Nav Flash Programming lt 0 Fk Processor Ver 0400 Flash Programming AU Flash Programming 450 Flash Programming GU Flash Programming lt 70 Flash Programming OU Flash Programming HU b ZP a ET aT altei Flash Programming tinish Device Checksum 0x1364 FPL Checksum Ox1364 B Hame FPL2_TEST HES Date 2004 03 29 00 57 20 Chksum BOOOh finish is displayed Area OO0000h 000FFFh Port UOHT chdl Checksum finish Speed 115200 Freg H d c ooo 8 Terminating the system lt 1 gt If other devices need not be programmed select File Quit to terminate the GUI software All settings executed so far are saved in the FPL2 INI file so that those settings can be reused when the GUI software is restarted lt 2 gt Disconnect the target cable from the target system lt 3 gt Disconnect the USB cable from the FPL2 9 Restart When the system is restarted the same screen as shown in Figure 5 6 appears Users Manual U17307EJ2VOUM O x Parameter file Load file Connection to device CHAPTER 6 CONNECTORS AND CABLES 6 1 USB Connector FPL2 Figure 6 1 Pin Layout of Power Supply Connector Table 6 1 Pin Assignment of USB Connector USB Connector FPL2 Signal Name a EOI Connector part number
35. for the installation folder and then click OK Figure 3 6 Changing Installation Folder Choose Folder Please choose the installation Folder Path SES ER Files SINECToolss21 Directories Program Files 3 ComPlus Applications InstallShield Installation Informat a LC Intel 20 i a Internet Explorer Messenger e When Custom is clicked Select the checkbox of the item to be installed and then click Next gt Figure 3 7 Custom Installation aiic uetan Check here when installing the GUI software Select Features Choose the features 54 Select the featires you want to install and clear the features you do not want to install Description mp eG FPL2V1 00 PG FPL2 1 00 Document Files PG FPL2 1 00 Check here when installing documents Space Required op C Pb K Space Available op C 1248260 K Click after confirming the check boxes Back 20 Users Manual U17307EJ2VOUM CHAPTER 3 SOFTWARE INSTALLATION 8 Specify or select the program folder and then click Next gt Figure 3 8 Program Folder Selection InstallShield Wizard Select Program Folder Please select a program folder Setup will add program icons to the Program Folder listed below ou may type a new folder name or select one from the existing folders list Click Next to continue Program Folders lt Back Cancel 9 Confirm the current setting and then click Next gt Program ins
36. gain e Connect the USB connector to another port of the USB hub If the same symptom occurs do not use the USB hub but directly connect the connector to the USB port of the personal computer User s Manual U17307EJ2VOUM 65 CHAPTER 9 TROUBLESHOOTING 9 2 Trouble During Operation Main Unit 1 When the FPL2 is connected to the personal computer but the Power LED is not turned on Cause The FPL2 or the USB port of the personal computer may be damaged Action Try a connection to another personal computer 2 The Add New Hardware Wizard screen is displayed when the FPL2 is connected with a personal computer Cause If the USB connector of the FPL2 is not inserted into the USB port during installation but into another USB port the FPL2 may be recognized as a new hardware item Action Install the driver by referring to 3 2 Driver Installation 9 3 Trouble During Operation Communication 1 Communication with the target device is not possible Cause The driver may not be installed correctly Action Check if NEC Electronics IE PC Interface PG FPL2 is installed correctly by referring to 3 2 Driver Installation Cause There may be an incorrect connection between the target cable and target system Action Check if the connection is correct Pay special attention to the following connections because the connections are confusing Connect DGCLK of the target cable to X1 of target device Connect DGDATA of the target
37. hat the drivers have been installed normally according to the procedure below When using the FPL2 the information to be checked here is needed Click the Device Manager tab and check that the drivers are installed normally Figure 3 26 Device Manager System Properties lx General Device Manager Hardware Profiles Performance Ce View devices by type C View devices by connection s Computer 6 5 CDROM H E Disk drives aa Display adapters AS Floppy disk controllers 9 GN Hard disk controllers H a Human Interface Devices Check that NEC Electronics IE PC Interface HE Keyboard PG FPL2 is present o RI Monitors ty Mouse Er NECPCIF o SS Network adapters o Ports COM amp LPT 9 K Sound video and game controllers Ay Storage device gt Go Il ci le o Properties Refresh Remove Print e Cautions 1 When using the FPL2 in Windows 98 Me do not select Or when communicating with the target device 2 When using the FPL2 in Windows 2000 KP do not perform Scan for hardware changes when communicating with the target device Remark If the drivers above are not displayed or the mark x or is prefixed refer to CHAPTER 9 TROUBLESHOOTING User s Manual U17307EJ2VOUM 31 CHAPTER 3 SOFTWARE INSTALLATION 3 4 Uninstallation 3 4 1 Driver uninstallation Uninstall the driver by manually deleting NEC Electronics IE PC Interface PG FPL2 on the Device Manager tab while th
38. he GUI software taking a case where the UPD78F9222 is used as the target device as an example This chapter covers how to start the system execute the Autoprocedure EPV command and program the target device Refer to CHAPTER 4 OPERATION USING GUI SOFTWARE for the other commands and applications O Series of operations described in this chapter The conditions of the series of operations described in this chapter are as follows e Target system Target device UPD78F9222 Voltage level 3V Communication UART CHO e FPL2 Parameter file 78F9222 PRM Clock setting 8 MHz Port UART ch0 115 200 bps MODE switch 3V Operation mode Chip Write HEX FPL2_TEST HEX Option setting Blank check before Erase Checksum after Program 1 Installing the GUI software 2 3 Install the FPL2 GUI software in the host machine you are using by referring to CHAPTER 3 SOFTWARE INSTALLATION if the software has not been installed yet Installing the driver Install the USB driver in the host machine you are using by referring to CHAPTER 3 SOFTWARE INSTALLATION if the driver has not been installed yet Installing the parameter file Copy the parameter file for the yPD78F9222 to the hard disk and install it in lt FPL2 installation path gt PRM Download the parameter file from the following http www necel com micro ods eng index html website in English http www necel com micro ods pn index html website in Japanese
39. he GUI software allows easy and comfortable access to all features of the FPL2 flash programmer The installation program is contained in the CD ROM ID78KOS QB Disk included with the QB 78KOSKX1MINI package Execute the following steps to install the GUI software 1 When using Windows XP log on as the computer administrator When using Windows 2000 log on as the Administrator 2 Insert the CD ROM ID78KOS QB Disk included with the QB 78KOSKX1 MINI package into the CD ROM drive 3 Double click My Computer CD ROM PG FPL2 and SETUP in that order Double click setup exe in the SETUP folder Figure 3 1 SETUP Folder SETUP Seles File Edit View Favorites Tools Help ae T i E x i Ty BZ Bivleze Back a Ka n Search K Folders Et Mame Size Type Date Modified File and Folder Tasks x nechst ein AER IN File 6 30 2004 4 19 PM _hecinst_ 1m_ SEB IN File 6 30 2004 4 19 PM Other Places 0 0409 ini SEB Configuration Settings 5 18 2004 11 55 AM Aw 0041 1 ini SEB Configuration Settings 5118 2004 11 55 AM 1033 mst 48 KB MST File 8 17 2004 3 52 PM Ka ee 1041 met 24KB MST File 8117 2004 3 52 PM e Docume 1 cab SEB Cabinet File 5117 2004 3 52 PM Bjlinstmsia exe 1 669 KD Application 3112 2002 12 45 AM linstmsiw exe 1 780 KD Application 3111 2002 10 06 AM A lsscripts Msi 697 KB Windows Installer Package 4 10 2003 3 03 AM A necsetup ini L KE Configuration Settings 207 2004 2 46 PM jl Ps FPL2 msi 1 251 KB Win
40. hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document but Ren
41. host machine before using the FPL2 Install the driver according to the following procedure Installation in Windows 98 Me See 3 2 1 Installation in Windows 98 Me Installation in Windows 2000 See 3 2 2 Installation in Windows 2000 Installation in Windows XP See 3 2 3 Installation in Windows XP 3 2 1 Installation in Windows 98 Me 1 When the FPL2 is connected with the host machine the FPL2 is recognized by Plug and Play and the wizard for adding new hardware is started Click Next gt Figure 3 12 Add New Hardware Wizard Windows 98 Add New Hardware Wizard This wizard searches for new drivers for USE Device A device driver is a software program that makes a hardware device work Cancel User s Manual U17307EJ2VOUM 23 CHAPTER 3 SOFTWARE INSTALLATION 2 The window below is displayed Check that Search for the best driver is selected then click Next gt Figure 3 13 Search Method Windows 98 Add New Hardware Wizard What do you want Windows to do Check that Search for the best driver is selected a D De Search for the best driver for pour device Recommended C Display a list of all the drivers in a specific location 0 you can select the driver you want Back Cancel 3 Check the Specify a location check box only and enter C Program Files NECTools32 bin PG FPLADRIVER in the address bar then click Next gt Figure 3 14
42. ics products are classified into the following three quality grades Standard Special and Specific The Specific quality grade applies only to NEC Electronics products developed based on a customer designated quality assurance program for a specific application The recommended applications of an NEC Electronics product depend on its quality grade as indicated below Customers must check the quality grade of each NEC Electronics product before using it in a particular application Standard Computers office equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots Special Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems life support systems and medical equipment for life support etc The quality grade of NEC Electronics products is Standard unless otherwise expressly specified in NEC Electronics data sheets or data books etc If customers wish to use NEC Electronics products in applications not intended by NEC Electronics they must contact an NEC Electronics sales representative in advance to determine NEC Electronics willingness to su
43. ipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under cert
44. le Read Figure 4 7 Parameter File Selection Window Look in E Frm y EA ex Files of type ET Files PRM sl Cancel A PRM File Read button A window for specifying a parameter file is displayed Specify the target file and click Open Users Manual U17307EJ2VOUM 41 CHAPTER 4 OPERATION USING GUI SOFTWARE lt 2 gt Communication interface to device Select the channel for communication between the FPL2 target device and host machine in this area Figure 4 8 Device Setup Window Communication Interface to Device Communication interface to device Port UART ch Port box Displays the communication channel between the FPL2 and target device e UART chO Remark Since the target device of the FPL2 is the 78K0S Kx1 the port is fixed to UART cho Speed box Displays the communication rate of the communication channel e 115 200 bps Remark Since the target device of the FPL2 is the 78KOS Kx1 the communication rate is fixed to 115 200 bps lt 3 gt Supply oscillator Select the clock that determines the programming data transfer and transfer rates in this area Figure 4 9 Device Setup Window Supply Oscillator Supply oscillator Frequency E ML Multiply rate fi OU Frequency box Sets the clock frequency of the target system Remark Since the target device of the FPL2 is the 78KOS Kx1 the clock frequency is fixed to 8 MHz Multiply rate S
45. m 2 3 3 Target system The target system must be equipped with a device interface that complies with the target cable specifications Refer to CHAPTER 6 CONNECTORS AND CABLES for details 2 3 4 USB connector The shape of the USB connector is a Mini B type Refer to CHAPTER 6 CONNECTORS AND CABLES for details 2 3 5 Target cable The tip of the target cable can be connected to the header pin that is 0 635 mm by 0 635 mm Refer to CHAPTER 6 CONNECTORS AND CABLES for details User s Manual U17307EJ2VOUM 13 CHAPTER 2 HARDWARE INSTALLATION 2 3 6 Connection procedure The procedure for connecting the FPL2 is described below Caution Be sure to install the software GUI software driver before making connections 1 Set the MODE switch according to the power supply of the target system Caution Be sure to set the MODE switch before making connections with the host machine and target system If connections are made based on an incorrect setting the FPL2 and target system may be damaged Figure 2 4 MODE Switch Setting MODE Set the MODE switch O NEC Target 3V PG FPLZ for 78K0S Kx1 Power Status 2 Connect the host machine with the FPL2 via the USB cable Check that the Power LED is turned on in green Cautions 1 Be sure to perform this step before making a connection with the target system If connections are made in an incorrect order the FPL2 and target syst
46. mmunication with the target device and the operating clock of the device differ depending on the device used Refer to the manual of the device used for details The following window opens User s Manual U17307EJ2VOUM 39 CHAPTER 4 OPERATION USING GUI SOFTWARE Figure 4 5 Device Setup Window Standard Tab Es Device Setup El Standard Advance Parameter file FAM File read Communication interface to device Port UART chO Supply oscillator Frequency Je MHz Multiply rate fi UU Operation Mode C Chip Start D C Block End Z Area FP Show Addres This window shows all basic options that can be set in accordance with the user environment and target device OK button Saves the settings in the Standard and Advance tabs and closes the window Cancel button Closes the window without saving the settings in the Standard and Advance tabs 40 Users Manual U17307EJ2VOUM CHAPTER 4 OPERATION USING GUI SOFTWAR lt 1 gt Parameter file This file holds parameters and timing data required to rewrite the flash memory of the target device Do not modify the data in the parameter file because the data is related to the guarantee of rewrite data The parameter file is protected by the checksum function If the checksum result indicates an error the FPL2 does not accept the parameter file Figure 4 6 Device Setup Window Parameter File Selection Parameter file PRM Fi
47. n Try using another personal computer or supply power from the target system by setting the MODE switch to Target User s Manual U17307EJ2VOUM 67 APPENDIX A PRODUCT SPECIFICATIONS A 1 Hardware Specifications Table A 1 Specifications of the Main Unit a fre Y Operating supply voltage VDD_USB 5 25 V Supply current VDD USB IE ME 500 mA Current consumption of the main unit UEM 175 mA MEN VDD output current a ae ae 200 mA Note The 3 V output of the FPL2 depends on the USB port of the host machine If the supply power of the USB port is unstable or does not satisfy the specifications of the target device set the MODE switch to Target to use the power supplied from the target system 68 Users Manual U17307EJ2VOUM APPENDIX A PRODUCT SPECIFICATIONS A 2 Dimensions 1 FPL2 Target 3V PG FPLZ for 78K0S Kx1 Power status Unit mm User s Manual U17307EJ2VOUM 69 70 2 FPL2 FA APPENDIX A PRODUCT SPECIFICATIONS Figure A 2 Dimensions of FPL2 FA Main Unit Users Manual U17307EJ2VOUM 20 34 Unit mm APPENDIX A PRODUCT SPECIFICATIONS 3 Target cable Figure A 3 Dimensions of Target Cable 120 30 Connector block Tip Figure A 4 Dimensions of Tip of Target Cable a gt i i 2 8 Pin Connection MAX Wa GE ee Unit mm Connector part number PS SF C2 1 manufactured by JAE Users Manual U17307EJ2VOUM 71 APPENDIX B WARRANTY AN
48. n the FPL2 RESET rise time Incorrect connection FPL2 RESET It takes time for the CPU RESET pin to go high after the FPL2 RESET level goes from low to high 60 Users Manual U17307EJ2VOUM CHAPTER 7 NOTES ON TARGET SYSTEMS CPU Pin Design Proposal RESET e Connection to a point where the target CPU RESET pin cannot be driven to low level by the FPL2 RESET signal Incorrect connection FPL2 RESET When the FPL2 RESET is driven low the level of the voltage at point A does not fall Serial When the CPU port used by the FPL2 is also connected to the input of an external device and if that device interface pin malfunctions disconnect the external device or make it output high impedance Example FP4 connector While the CPU port used by the FPL2 is also connected to the output of an external device and if a signal collision occurs disconnect the external device Example FP4 connector Collision External device For the unused pins refer to the user s manual of the device User s Manual U17307EJ2VOUM 61 CHAPTER 7 NOTES ON TARGET SYSTEMS The following show examples of the interface circuits of UART asynchronous communication port Refer to the above design proposal for the pin processing of the device to be used Figure 7 1 UART Interface Circuit Example Vcc Vcc Vcc Connector GND RESET DGDATA VDD DGDATA N C N C N C N C N C N C N C DGCLK N C N C 7616 50
49. ny errors that may appear in this document e NEC Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products No license express implied or otherwise is granted under any patents copyrights or other intellectual property rights of NEC Electronics or others e Descriptions of circuits software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples The incorporation of these circuits software and information in the design of a customer s equipment shall be done under the full responsibility of the customer NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits software and information e While NEC Electronics endeavors to enhance the quality reliability and safety of NEC Electronics products customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely To minimize risks of damage to property or injury including death to persons arising from defects in NEC Electronics products customers must incorporate sufficient safety measures in their design such as redundancy fire containment and anti failure features e NEC Electron
50. of the following optional search locations that you specify To start the search click Next IF you are searching on a floppy disk or CD ROM drive Insert the floppy disk or CO before clicking Next Optional search locations CD ROM drives Je Specify a location Microsoft Windows Update Back Cancel 4 Enter C Program Files NECTools32 bin PG FPL2 DRIVER in the address bar then click Next gt Figure 3 20 Address Specification Windows 2000 Found New Hardware Wizard z Eo SG x Insert the manufacturer s installation disk into the drive DK Sg selected and then click OK Cancel Copy manufacturer s files from Enter C Program Files NEC Tools32 bin PG FPL2 DRIVER Remark If the installation destination folder is changed for GUI software installation enter new foldenbin PG FPL2 DRIVER Users Manual U17307EJ2VOUM 27 CHAPTER 3 SOFTWARE INSTALLATION 5 The driver file is searched and the window below is displayed Click Next gt Figure 3 21 Driver File Search Windows 2000 Found New Hardware Wizard Aa Driver Files Search Results The wizard has finished searching for driver files for pour hardware device The wizard found a driver for the following device NEC Electronics IE PC Interface PG FPL2 Windows found a diver for this device To install the driver Windows found click Mert c proeram tiles nectooled2 b intoe tplesdr vertpetple int C
51. ognized by Plug and Play Cause The USB connector may not be inserted normally into the USB port of the personal computer Action Check that the USB connector is inserted fully into the USB port of the personal computer Alternatively disconnect the USB connector then insert the USB connector again after a while 2 The driver file cannot be found at a specified location Cause The GUI software of the FPL2 may not be installed correctly Action Install the GUI software again by referring to 3 1 GUI Software Installation 3 NEC Electronics IE PC Interface PG FPL2 is not displayed in the Device Manager Alternatively the or x is prefixed Cause The USB connector may not be inserted normally into the USB port of the personal computer Action Check that the USB connector is inserted fully into the USB port of the personal computer Alternatively disconnect the USB connector then insert the USB connector again after a while Cause The driver may not be installed correctly Action lt 1 gt Right click the driver marked with or x when the FPL2 is connected to the personal computer and select in the right click menu lt 2 gt Execute Hardware Modification Scan in the Device Manager lt 3 gt Install the driver again with Plug and Play Cause The device may not be recognized in the case of connection with the USB hub Action Try the following e Disconnect the USB connector then insert the USB connector a
52. pecifies the division rate or multiplication rate of the target device Remark Since the target device of the FPL2 is the 78KOS Kx1 this item is fixed to 1 00 42 Users Manual U17307EJ2VOUM CHAPTER 4 OPERATION USING GUI SOFTWAR lt 4 gt Operation Mode The flash memory may be divided into blocks or areas depending on the target device This menu is used to select the operation mode of the flash memory Some devices do not have either or both division modes Block and Area In this case a mode that is not available cannot be selected Figure 4 10 Device Setup Window Operation Mode Selection Operation Mode C Chip C Block End x Area Show Address When Chip is selected The entire flash memory area of the target device is subject to rewrite processing When Block is selected Specify the Block number range subject to rewrite processing by using Start End The Start End list boxes display the Block number where the flash memory of the target device is configured Remark The Start Block number is fixed to 000 Specify the End Block number only When Area is selected This item is not supported Show Address check box Specifies whether numbers or addresses are displayed in the Start End list boxes If this check box is checked addresses are displayed If it is not checked numbers are displayed User s Manual U17307EJ2VOUM 43 CHAPTER 4 OPERATION USING GUI SOFTWARE b Advance se
53. pport a given application Note 1 NEC Electronics as used in this statement means NEC Electronics Corporation and also includes its majority owned subsidiaries 2 NEC Electronics products means any product developed or manufactured by or for NEC Electronics as defined above M8E 02 11 1 User s Manual U17307EJ2VOUM 3 GENERAL PRECAUTIONS FOR HANDLING THIS PRODUCT 1 Circumstances not covered by product guarantee If the product was disassembled altered or repaired by the customer If it was dropped broken or given another strong shock Use at over voltage use outside guaranteed temperature range storing outside guaranteed temperature range If power was turned on while the USB cable or target system connection was in an unsatisfactory state If the USB cable target cable or the like was bent or pulled excessively If the product got wet If the product and target system were connected while a potential difference existed between the GND of the product and the GND of the target system If a connector or cable was removed while the power was being supplied to the product If an excessive load was placed on a connector or socket 2 Safety precautions If used for a long time the product may become hot 50 C to 60 C Be careful of low temperature burns and other dangers due to the product becoming hot Be careful of electrical shock There is a danger of electrical shock if the product is used as described above
54. rameter File Selection Look ir Frm CS 709222 p m Si ole File name 7549222 pm Files of type PRM Files PRM sl Cancel ve lt 4 gt Set the items in the Operation Mode field so that the FPL2 is adjusted to the user programming environment Here assume that the settings shown below are set Figure 5 4 Device Setup Window Standard Tab lt After Setting gt ES Device Setup x Standard Advance Fort ap ag Frequency E MHz Speed 115200 bps Muli rate 91 00 Operation Mode Block End 015 Area ShowiAdares User s Manual U17307EJ2VOUM 51 CHAPTER 5 USAGE EXAMPLE lt 5 gt Switch to the Advance tab Figure 5 5 Device Setup Window Advance Tab SR Device Setup Sead VET alten ii lt Command options gt Blank check before Erase Checked Security flag after Program Not checked Checksum after Program Checked 52 Users Manual U17307EJ2VOUM CHAPTER 5 USAGE EXAMPLE lt 6 gt Click OK The GUI software sets the parameters When the settings are completed the following screen is displayed Figure 5 6 Completion of Parameter Setting 2 0 x File Device View Help pag Y Y Parameter file Device Mame arose Mame oF O22 2 prim Format O413 Version El Uh Processor Ver 0300 Name Date bk zum Grea Connection to device UART cho 176200 H Ready mu 6 Selecting a user program lt 1 gt Select File
55. s Manual U17307EJ2VOUM NEC Electronics Hong Kong Ltd Hong Kong Tel 2886 9318 NEC Electronics Hong Kong Ltd Seoul Branch Seoul Korea Tel 02 558 3737 NEC Electronics Shanghai Ltd Shanghai P R China Tel 021 5888 5400 NEC Electronics Taiwan Ltd Taipei Taiwan Tel 02 2719 2377 NEC Electronics Singapore Pte Ltd Novena Square Singapore Tel 6253 8311 J04 1 Target Readers Purpose Organization How to Read This Manual PREFACE This manual is intended for users who use the PG FPL2 when designing and developing a system using an NEC Electronics on chip flash memory microcontroller This manual is intended to give users an understanding of the basic specifications and correct use of the PG FPL2 By using the PG FPL2 programs can be easily erased from or written to the flash memory of an NEC Electronics 78K0S Kx1 Series on chip flash memory microcontroller or can be verified on Windows screens while the microcontroller is mounted on the user board This manual includes the following sections Overview Hardware installation Software installation Operation using GUI software e Usage examples Connectors and cables Notes on target system Circuit diagrams Troubleshooting To understand the overall functions and usage of the PG FPL2 read this manual in the order of the CONTENTS Be sure to read CHAPTER 4 OPERATION USING GUI SOFTWARE because this chapter presents important informa
56. s products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics User s Manual PG FPL2 Flash Memory Programmer Document No U17307EJ2VOUMOO0O 2nd edition Date Published December 2004 NS CP K NEC Electronics Corporation 2004 Printed in Japan MEMO 2 User s Manual U17307EJ2VOUM Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries PC AT is a trademark of International Business Machines Corporation Pentium is a trademark of Intel Corporation e The information in this document is current as of December 2004 The information is subject to change without notice For actual design in refer to the latest publications of NEC Electronics data sheets or data books etc for the most up to date specifications of NEC Electronics products Not all products and or types are available in every country Please check with an NEC Electronics sales representative for availability and additional information e No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics NEC Electronics assumes no responsibility for a
57. tallation starts Figure 3 9 Start of File Copy Operation InstallShield Wizard Start Copying Files Review settings before copying files Setup haz enough information to start copying the program files IF you want to review or change any settings click Back JE you are satished with the settings click Next to begin copying files Current Settings Product to install PG FPL2 1 00 PG FPL2 1 00 Document Files Target Directory C Program Piles HNECT oole32 Program Folder NEC Tools 24 Cancel User s Manual U17307EJ2VOUM 21 CHAPTER 3 SOFTWARE INSTALLATION 10 When installation of the GUI software is complete the screen shown below appears Click to terminate the installer Figure 3 10 Completion of Installation InstallShield Wizard InstallShield Wizard Complete Setup has finished installing Pia ERD A VT DU on your computer Cancel 11 The following folders are created upon completion of installation Figure 3 11 Folder Configuration After Installation Program File Folder specified as the installation destination NECTool32 bin GUI software PG FPL2 FPL2 exe FPL2ctl dll DRIVER Pgfpl2 int Pgftpl2 sys PRM PRM file storage folder doc PG FPL2 PG FPL2_UM_E pdf README_E pdf ___ 22 User s Manual U17307EJ2VOUM CHAPTER 3 SOFTWARE INSTALLATION 3 2 USB Driver Installation The driver needs to be installed in the
58. the PAGE DOWN key to see the rest of the agreement USER LICENSE AGREEMENT IMPORTANT READ CAREFULLY This User License Agreement TUL Is a legal agreement between you either a natural person or an entity and NEC Electronics Corporation NEC for the SOFTWARE PRODUCT As used herein SOFTWARE PRODUCT means the NEC software product provided with this ULA which includes computer software and may include associated media printed materials and online files or data By installing copying or otherwise using Do you accept all the terms of the preceding License Agreement If you choose No the setup mill close To install PG FPL247 00 you must accept this agreement Back Y No 7 Check that Typical is selected then click Next gt Figure 3 5 Setup Type InstallShield Wizard Setup Type z j Choose the setup type that best suits your need k Ap Please select a setup tupe Choose which program features you want install Recommended for advanced Users M Destination Folder C Program Files MECT oala Browse lt Back Cancel User s Manual U17307EJ2VOUM 19 CHAPTER 3 SOFTWARE INSTALLATION Remark By selecting Custom only the GUI software or document can be installed The GUI software installation destination can be changed by clicking Browse This manual assumes the default installation folder e When is clicked The directory selection window is displayed Specify the path
59. tion for using the PG FPL2 It is assumed that the readers of this manual have general knowledge of electricity logic circuits and microcontrollers In the explanations of the operation of the applications it is also assumed that the readers have sufficient knowledge of Windows For the usage and terminology of Windows 98 Windows Me Windows 2000 and Windows XP refer to each Windows manual The mark shows major revised points User s Manual U17307EJ2VOUM Conventions Terminology Note Footnote for item marked with Note in the text Caution Information requiring particular attention Remark Supplementary information Numeral representation Binary xxxx or xxxxB Decimal xxxx Hexadecimal OxxxxH or xxxxH e Any character or item on screen OK Name of button Menu lt gt Dialog box name The meanings of the terms used in this manual are as follows Target system User designed board on which NEC Electronics on chip flash memory microcontroller is mounted FP4 connector Abbreviation of PG FP4 target connector type A FA adapter Adapter board to write programs to NEC Electronics on chip flash memory microcontroller 78KOS Kx1 Generic name of 78KOS KU1 78KOS KY1 78KOS KA1 and 78K0S KB1 Note The FA adapter board is a product of Naito Densei Machida Mfg Co Ltd If you have any questions about the FA adapter board contact Naito Densei Machida Mfg Co Ltd Tel 81 45 475 4191 User
60. to CHAPTER 6 CONNECTORS AND CABLES 2 3 1 FPL2 display specifications connector and MODE switch settings Figure 2 2 Layout Drawing of Connectors and LEDs MODE switch USB connector MODE C iD NEC Target 3V PG FPL2 for 78K0S Kx1 Power Status TT TT OO DO OO D Oo Target Power LED Status LED Target cable connector 12 Users Manual U17307EJ2VOUM CHAPTER 2 HARDWARE INSTALLATION Target cable connector Used to connect the connector of the target cable USB connector Used to connect the USB cable to be connected to the host machine Power LED Turned on in green when the FPL2 is connected to the host machine Status LED Blinks in red when the FPL2 is communicating with the target device MODE switch Switches power to be supplied to the target system Target Used to supply Von from the target system 3 V Used to supply power to the target system with 3 0 V Vop from the FPL2 Caution When the Status LED is blinking communication with the target device is in progress Do not disconnect the target cable and USB cable 2 3 2 FPL2 FA connector Figure 2 3 Layout Drawing of FPL2 Connectors Target connector OO O O O 00 Oto O O Component side front Soldering side rear FP4 connector Target connector Used to connect the tip of the target cable FP4 connector Used to connect the FA adapter board or target syste
61. toprocedure EPV command to verify the checksum values of the data written to the flash memory of the target device and the program file to detect a communication error of the user program while it is being transmitted specify automatic execution of the CheckSum command after execution of the Program command using the Command options on the Advance tab of the Device gt Setup menu During EPV the progress status of the programmer operation is displayed in the action log window Refer to CHAPTER 5 USAGE EXAMPLE for the selected command and its execution operation and message After completing the Autoprocedure EPV command the GUI software displays the target device command execution result Signature read command This command is not supported Setup command al The Setup command is used to perform flash memory writing settings in accordance with the a user environment and command option settings Each time the GUI software is started the parameter file PRM and customized setup file SET that were used last are read and their setting contents are displayed Settings can be changed in accordance with the user environment except for the parameters that are dimmed In addition new settings can be saved to the customized setup file the data of the parameter file cannot be changed a Standard setup This menu is used to set the rewriting environment of the target device s flash memory The mode of co
62. tup This menu is used to specify command options and security flag setting The Advance tab is displayed by clicking Advance Figure 4 11 Device Setup Window Advance Tab Fa Device Setup El Standard Advance Command options T Blank check before Erase P Read vent atten Program Security flag after Program Checksum after Program Security flag settings Disable Block Erase Disable Program lt 1 gt Command options Specify the options for the FPL2 flash processing commands in this area Figure 4 12 Device Setup Window Command Options Command options Blank check before Erase Read verify after Program Security flag after Program Checksum after Program Blank check before Erase check box If this check box is checked a blank check is performed before execution of the Erase and Autoprocedure EPV commands If the result of the blank check is OK erase processing is not executed Read verify after Program check box This item is not supported Security flag after Program check box If this check box is checked automatic programming of the selected security flag is executed after execution of the Program and Autoprocedure EPV commands 44 User s Manual U17307EJ2VOUM lt 2 gt CHAPTER 4 OPERATION USING GUI SOFTWAR Checksum after Program check box If this check box is checked the checksum values of the target device connected to the FPL

PG-FPL2 Flash Memory Programmer UM

Contents

Download Pdf Manuals

Related Search

Related Contents