USER MANUAL
Contents
1. Using appropriative plug connect computer light and power main lead Pay attention to consistent of voltage freguency and supply source of backboard of computer light Suggest each computer light to use a separate power supply so each light can be turn on and turn offat will L Brown E Yellow Green N Blue Important matters Each computer light should be earthed and whole electro assembling must accord with standard demand Monitoring restoration system After computer light switch on power circuitry will be install This function makes lamp cobra moving to a limiting position and it will turn interior color and superimposed wheel of pattern Thus the control system of microprocessor can login all place of electrical machines which controlled by it It will bring electric noise in computer interior when modulator tube damage or burnout Maybe it will disturb normal operation of MPU Computer light has an electronic monitoring system that can watch operation of MPU and ensure that will start up reinstallation function when it is disturbed After it finish computer light can accept new control instruction and operate without a hitch 4 Connection of control communication wire Connection of controller and computer light or connection between each computer light should use two core shielded cable and diameter of each core should be 0 5MM at least When it joined in or come out it should be used cylindrical three legged XLR plug and2. open the cover forth gently at the tail of shine lamp screw off four coppery screw and move metallic gobo flag and heat guard of two sides then can replace lamp When install it please use OSRAM or PHILIPS MSD250W modulator tube Pay attention to screw down the screw of two sides of lamp or it cause high voltage short circuit and discharge for poor contact It influence service life of lamp and damage components of circuit board After finish it please strengthen the metallic gobo flag and heat guard of two sides of lamp firstly Then using adhesive tape to fold covering shell and strengthen screws of right and left of it MSD light products are provided with high voltage modulator tube what has exterior igniter When operate these modulator tubes it must be careful and should read the instruction of modulator tube that offer by manufacturer before operation Warning 1 Don t forget install metallic gobo flag and heat guard that beside the lamp or thermal radiation is easy to bake the plastic shell distortion Seriously it will raise fire alarm Manufacturer will not responsible for these losses Warning 2 Modulator tube will reach to a high temperature when it works and the trait of gas discharge lamp can not intermittent power supply It must cool at least 15 minutes to work again after power supply cut off or it will induce high pressure discharge short circuit and even burn out parts of computer control panel 3 Power supply
3. outlet which supplied along with computer light Connection of XLR can refer to the list below Attention every line should not touch each other or touch plug Computer light can accept data control signal of DMX512 1990 format Control signal connect with panel which earmarked DIGITAL IN then connect socket which earmarked DIGITAL THRU with socket of next computer light which earmarked DIGITAL IN After receive signal of DMX512 the status lamps close to switch of address code will fulgurate Or it will extinguish If it always in shine it means DMX signal is false DMX512 PIN FUNCTION 1 GND 4 2 DATA 3 DATA Suggest to use DMX signal terminal it can avoid the breakage of data control signal Cause by electric noise In simple terms DMX terminal is a XLR linker in which has a 120 Q resistance between two legged and three legged plug And the resistance should be connected with DIGITAL THRU socket of the last computer light of computer light chain The connection can refer to table below The connection of DMX terminal connect a 120 Q _ resistance between two legged and three legged of XLR plug and connect it to DIGITAL THRU socket of the last computer light of computer light chain 5 Corrective maintenance If lens of computer light be damaged or broken please replace a new one and the same to modulator tube If light turn dark it means service life of modulator tube is up should be replaced in
4. 250W MOVING HEAD WASH RG M09 USER MANUAL RIGE LIGHTING amp AUDIO EQUIPMENT CO LTD Catalogue Installation of computer light Installation of lamp Power supply Connection of control signal line Corrective maintenance Cleanly maintenance Warning Difficulty disposal 0 ON DN RF WW Qualification Notice because the policy of improve the products quality of our company Maybe some data in the instructions will change in future By that time we won t inform you about the changed matters Marten company reserve the right of changing correlative specification when improve the products Publisher of the instruction will not responsible for veracity of information and some correlative results caused by this information 1 Installation of computer light Using eight M10 size bolts through making use of bracket that owned by computer light install Make sure the firmness of installation in case swing or glide happen when it works Each weight of computer light is 20 5KG more or less Before installation it should be ensure if frame can support the weight For safety a safe chain should be through the side handle of lighting body Notice please don t use the die down yoke of computer light to rise to lower and move it 2 Installation of lamp loosen plastic body which locate in luffing structure of computer lighting body and strengthen screw of right and left cover shell then
5. ction table Press ENTER letter A will extinguish using UP or DOWN choose address code 001 512 Press ENTER to confirm and exit or press ESC to give up and exit When accepting host computer in phase address must be set 001 When display address code if equip connectionless DMX control video screen will twinkle If equip connection DMX control video screen will not twinkle but DMX signal lamp twinkle because it has signal DN Pr DMX presupposition The function permit choose different control mode Press UP or DOWN browse the function table Press ENTER to put in Press UP or DOWN to choose nod 1 or nod 2 Press ENTER to save and exit or press ESC to give up and exit Nod 1 Control of natural number of channels Nod 2 Control of the lesser channels When accepting host computer in phase DMX presupposition should set nod 1 Test program This function permit execute inner demonstration program without in an extension control state The setting should be saved Every startup enter test program automatically when it is not exit Press UP or DOWN to browse the other function table Press ENTER to enter 1 nod 1 test program Press UP or DOWN to choose other mode Press ENTER to enter Display RUN to test operation Press ESC to exit 2 NAST host comp
6. fan if it operate normally Shadow has halo Check the number of electro focus channels if it suit current range of the projection Beam looks gray Maybe service life of modulator tube is over it must be replaced Check optical component if it is clean Lamp is not bright 1 Because of improper operation lamp not completely cool The fan in the lighting body must be cool 10 minutes cut off power supply at least 5 minutes makes internal inductor renew completely then switch on power supply 2 Check if service life of lamp is over 3 Check lamp and trigger line if it is creepage desquamation or poor contact 4 Replace a new trigger Don t illuminate on tinderbox computer light must keep 5M away from tinderbox Computer light should keep 0 5M away the surface of adjacent object Don t look beam in the face or it may injure your eyes Notice modulator tube will reach to a high temperature when it works It must be completely cool at least 15 minutes before operate again 8 Difficulty disposal 9 Oualification Power supply 220 230V 50Hz Power consumption 300VA 220VA Modulator tube NSD250W GS Service life 700 hours Colors 7 dichroic filters have white light effect Color turn plate can rotate continuously And every direction has iridescent effect Pattern 6 rotation metal patterns a hyaline effect pattern and a rotundity pattern which can rotate rever
7. rsing Press ENTER to save and exit and press ESC to exit RESET The function can restart to primary standard positioning Press ENTER to confirm
8. se repose and auto timing effect Dimmer and strobe Ouick acting dimmer can intermit beam rapidly and can realize strobe effect 1 7 times each second Prism and prism rotation effect A prism can rotate reverse speed adjust and repose Automatic focus function Electro focus be able to adjust definition of pattern Electrical machine It is composed of 9 precision stepper motor which are controlled by a set in MPU Control MPU Adopt CPU of high stability and high anti jamming capability Numerical control DMX512 Auto mode It makes 4 computer lights constitute a combination and operate according to built in program Activation of audio frequency It makes 4 computer lights constitute a combination and operate according to built in program of activation of audio frequency Lighting body It is compose of plastic shell And streamline form design Size and weight 494 420 535mm Weight 26kg Operating specification of control display panel The list of control display panel designed specially for many types of computer 7 I II III light and eguipped multifunctional control mode it is simple to control A few functions not eguipped in some types of computer light and the corresponding option of list set inefficacy 1 DMXS512 address enactment The function can change address enactment Press ESC once or more until it display A 001 At this time press UP or DOWN can browse the fun
9. time The old modulator tube can explode When computer light works out of order fuse in back panel should be checked Notice If it need replace using same spec fuse that earmarked in back panel In the computer light circuit board has a 3AT fuse If the fuse has blown it need replaced by professional Computer light also have two heat protectors they should cut off power supply when the temperature is too high If it happened fan should be checked whether there is a barrage or not If fan is dirty please switch on the power supply after clean it Examine operation of fans if it doesn t work please mend it by professional 6 Cleanly maintenance In order to computer light operate steadily it should keep clean Suggest clean lighting body and fan every 15 days Lens and dichroic filter should be cleaned at stated time to assure the best light effect Don t use any deliquescent cleaner to clean dichroic filter 7 Warning Don t dismounting or refit computer light 5 Don t touch water and other kind of liquid and metal substance IP20 Don t install in a high wettest condition Problem The way to solve Computer light can t start Check fuse of back panel Though it shine computer light don t accept dictate of control Check data startup address see section 5 and check connection of communication control line see section 4 Computer light works only in intermittence Check
10. uter control The function permitted that if it is necessary for host computer to send DMX synchronizing signal to secondary computer When it is operating test program press UP or DOWN to choose the 8 IV V VII other mode press ENTER to enter Display ON to send signal as host computer and DMX signal lamp is on Display OFF not send signal and DMX signal lamp is off Press ENTER to save and exit Press ESC to exit After set it ON the connection of external DMX control must be intermitted and two host computers that have the same settings cannot be on a line AUDI music handle The function permit kindle test program by using voice 1 Press UP or DOWN to browse the other function table 2 Press ENTER to enter Press UP or DOWN to choose ON or OFF which decide if it use music kindle ON express using music kindle while OFF express not It is controlled automatically by test program After set ON the audio signal lamp will twinkle to the music when operate test program R PAN The function permit that reverse horizontally Press ENTER to enter Press ON to reverse Press OFF to stop reversing Press ENTER to save and exit and press ESC to exit R TILT The function permit that reverse vertically Press ENTER to enter Press ON to reverse Press OFF to stop reve
Download Pdf Manuals
Related Search