Home

Untitled

1. CARRY OUT THE FOLLOWING STEPS SHOWN IN 15 TO MOUNT THE PANEL USING ADHESION gt CLEAN THE SURFACE OF THE GLASS OVERLAY AND THE DISPLAY gt APPLY THE 3M ADHESIVE ALONG THE EDGES OF THE GLASS OVERLAY PRECISELY AS SHOWN IN STEP 1 gt FINEIR TOUCH PANEL ON THE SURFACE OF THE DISPLAY AS SHOWN IN STEP 2 gt N ORDER TO GET GOOD ADHESION RESULT IT IS STRONGLY RECOMMENDED TO LAY THE DISPLAY DOWN HORIZONTALLY AS SHOWN IN STEP 3 TO COMPLETE ADHESION gt APPLY CONSTANT PRESSURE EVENLY OVER THE GLASS USING WEIGHTS LET THE ADHESIVE DRY FOR AT LEAST 2 HOURS BEFORE PROCEEDING TO THE NEXT STEP WARNING gt DO NOT DIRECTLY MOUNT THE FINEIR TOUCH PANEL ONTO THE DISPLAY SURFACE IN VERTICAL POSITION WITHOUT SECURING THE PANEL IN PLACE BOTH THE TOUCH PANEL AND DISPLAY COULD BE DAMAGED AS A RESULT OF INCORRECT INSTALLATOIN IMPORTANT gt SURE THAT THE PANEL IS PROPERLY ALIGNED TO BE IN THE MIDDLE OF VIEWABLE OF THE DISPLAY CHECK ALL ALONG THE EDGES OF THE DISPLAY TO ENSURE THAT THE PANEL IS PARALLEL TO THE DISPLAY AND IS NOT TILTED IN ANY DIRECTION gt ANY ANGLE FORMED BETWEEN THE EDGE OF DISPLAY AND THE EDGE OF PANEL WILL CAUSE THE TOUCH PANEL TO BE INACCURATE WHICH MAY PREVENT PROPER CALIBRATION TOUCH PANEL USER MANUAL REV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 24
2. LARGER THAN 32 FIGURE 13 ILLUSTRATES HOW TO MOUNT THE PANEL ONTO YOUR DISPLAY WITH ADJUSTABLE HOOKS FIGURE 13 THERE ARE 2 DIFFERENT WAYS TO MOUNT THE PANEL ONTO YOUR DISPLAY AS SHOWN IN FIGURE 13 FOLLOWING STEP 1 LATCH THE TOP HOOKS ONTO THE DISPLAY FIRST THEN ATTACH THE HOOKS ON BOTH SIDES FOLLOWING STEP 2 SLIDE THE PANEL DOWN THE DISPLAY FROM THE TOUCH PANEL USER MANUAL REV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 21 FIGURE 14 ILLUSTRATES HOW FASTEN THE ADJUSTABLE HOOKS FIGURE 14 Adjustable hook Screw trough Adjustable hook Till HII AFTER THE PANEL HAS BEEN MOUNTED POSITION THE ADJUSTABLE HOOKS THE SAME SPOT AS THE SCREW HOLES ALONG THE BACK OF THE DISPLAY THEN LOCK THEM INTO PLACE BY TIGHTENING THE HOOK TOUCH PANEL USER MANUAL REV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 22 4 6 MOUNTING THE TOUCH PANEL ONTO THE DISPLAY BY ADHESION IF IN A SITUATION WHERE ADJUSTABLE HOOKS ARE NOT APPLICABLE AN ALTERNATIVE ADHESION METHOD CAN BE USED TO MOUNT THE PANEL FIGURE 15 ILLUSTRATES THE TYPICAL RECOMMENDATIONS FOR INTEGRATION BY ADHESION FIGURE 15 Touch Frame Touch Frame LCD PDP Display N LEIJE Desktop A S lt b Tn TOUCH PANEL USER MANUALREV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 23
3. OVERLAY FIGURE 8 IMPORTANT gt ENSURE THAT THE GLASS IS CORRECTLY ALIGNED WITH THE PANEL ALONG THE EDGES gt APPLY CONSTANT PRESSURE EVENLY ON THE GLASS OVERLAY WITH WEIGHTS AS SHOWN IN FIGURE 8 gt LETTHEADHESIVE DRY FOR AT LEAST 12 HOURS BEFORE PROCEEDING TO THE NEXT STEP TOUCH PANEL USER MANUALREV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 16 4 INSTALLING THE TOUCH PANELONTO THE DISPLAY THIS SECTION OF THE MANUAL DETAILS THE RECOMMENDED INSTALLATION GUIDELINES TO INSTALL THE FINEIR TOUCH PANEL ONTO YOUR DISPLAY NOTES BEFORE INSTALLING THE FINEIR TOUCH PANEL ON YOUR DISPLAY ENSURE THAT IT IS NOT CONNECTED TO YOUR COMPUTER CORRECT INSTALLATION OF THE FINEIR TOUCH PANELIS VITAL TO ACHIEVING PERFECT PERFORMANCE MOUNTING THE TOUCH PANEL COULD HAVE DETRIMENTAL EFFECT ON THE PERFORMANCE OF THE FINEIR TOUCH PANEL IF DONE INCORRECTLY THEREFORE GUIDELINES SHOULD BE FOLLOWED INSTALLATION DIAGRAMS IN THIS SECTION ARE FOR REFERENCE ONLY AND ARE NOT TO SCALE 4 1 TYPICAL INSTALLATION GUIDELINES THERE ARE TWO OPTIONS TO MOUNT A FINEIR TOUCH PANEL ONTO THE DISPLAY UNIT NORMALLY THE TOUCH PANEL IS MOUNTED WITH OUR PATENTED ADJUSTABLE HOOKS AN ALTERNATIVE METHOD IS BY USING ADHESION HOWEVER THIS METHOD MUST BE CARRIED OUT CAREFULLY BECAUSE IT IS VERY DIFFICULT TO REVERT ONCE THE ADHESIVE BONDING HAS SET THE INSTALLER MUST FOLLOW THESE INSTRUCTIONS IN ORDER TO AVOID ANY MISHANDLING OR DAMAGE INST
4. ALLING BY ADJUSTABLE HOOK PLEASE FOLLOW STEPS 4 3 4 5 DETAILED IN THIS SECTION IF INSTALLING BY ADHESION PLEASE SKIP TO STEP 4 6 4 2 NECESSARY PARTS FOR INSTALLING THE FINEIR TOUCH PANEL 1 ADJUSTABLE HOOKS PIECES DEPENDING ON PANEL SIZE 2 SCREWS 6 PIECES DEPENDING ON PANEL SIZE 3 3M VHB ADHESIVE FIGURE 9 SHOWS THE NECESSARY PARTS FOR INSTALLING THE FINEIR TOUCH PANEL ONTO YOUR DISPLAY FIGURE 9 95 2 JU L Screws Adjustable Hooks 4 3 ADJUSTABLE HOOK ASSEMBLY AND DISASSEMBLY OUR PATENTED ADJUSTABLE HOOKS ARE SPECIALLY DESIGNED TO ALLOW FOR SIMPLE MOUNTING AND DISMOUNTING OF THE FINEIR TOUCH PANELS WITHOUT USING ANY ADHESIVE MATERIALS THIS DESIGN ENABLES THE END USER TO CHANGE THE DISPLAY UNIT FREQUENTLY IF NECESSARY ALSO ALLOWS FOR MUCH EASIER MAINTENANCE OF THE DISPLAY OR THE TOUCH PANEL IF REQUIRED TOUCH PANEL USER MANUAL REV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 17 FIGURE 10 ILLUSTRATES THE DIRECT ASSEMBLY AND DISASSEMBLY OF ADJUSTABLE HOOK FIGURE 10 Hook Spring Hook Locking ASSEMBLE AN ADJUSTABLE START BY INSERTING THE HOOK SPRING INTO THE PIECE AS SHOWN IN STEPS TO 3 OF FIGURE 10 ENSURE THAT BOTH PIECES ARE FACING THE RIGHT DIRECTION BEFORE PROCEEDING AFTERWARDS INSERT THE HOOK LOCKING PIECE INTO THE COMPLETED HOOK FROM THE OPPOSITE SIDE OF WHERE YOU INSERTED THE HOOK SPRING AS SHOWN IN STEPS 4 TO 6 A FINISHED AD
5. FINEIR INFRARED TOUCH PANEL INSTRUCTION MANUAL Revision 1 8 Part 2 Glass Integrating and Display assembling THE F LLOWINGIS A LIST OF REGISTERED PATENTS BELONGING FINEIR 021497613 03113702 4 200820155581 2007100286896 5 200710025079 5 200720045219 4 300 7720051069 2 2007200524233 2007200530037 2008100265609 200810199142 200820044444 200820049720 7 20082020036 L0 20091 0036793 1 2009200532466 0 200920060780 3 200920 060781 8 087429706 101329612 PCT CN2 008 000259 08113806 9 09112101 2 09112100 3 1109024 11113642A 11278165A FINER TECHNOLOGY FAR EAST CO ADDRESS B VF BLE D W INDUSTRIAL BUILDING NO 25 HUNG ROAD KWUN TONG KOWLOON HONG KONG 111 52 3642 7512 FIN EIA 852 2342 1559 TOUCH SYSTEMS E MAILISALES GQIFINEIR COM W EEBSITE W WW FIMEIER CM InterDi Dy Interdipros srl www interdi it TOUCH USER LB FiNEIR TOUCHCONTROL SOFTWARE VERSION 2 1 3 INTEGRATING THE GLASS OVERLAY OR OTHER OVERLAY THIS SECTION OF THE MANUAL DETAILS THE RECOMMENDED ASSEMBLY GUIDELINES FOR INTEGRATING THE GLASS OVERLAY OR OTHER TYPES OF OVERLAY INTO THE TOUCH PANEL NOTES BEFORE INTEGRATING THE GLASS OR ANOTHER TYPE OF OVERLAY SUCH AS ACRYLIC OR PLASTIC ENSURE THAT THE DIMENSIONS ARE MADE ACCORDING TO THE TOUCH PANEL DIMENSIONS INCORRECT gt DIMENSIONS MAY CAUSE UNEXPECTED INTEGRA
6. JUSTABLE HOOK SHOULD BE SECURE ON THE HOOK LOCKING PIECE AND SHOULD NOT BE TILTED IN ANY DIRECTION TOUCH PANEL USER MANUAL REV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 18 FIGURE 11 ILLUSTRATES HOW ADJUST THE HOOKS FIGURE 11 TO ADJUST THE HOOKS SIMPLY PRESS DOWN ON THE HOOK SPRING WITH YOUR THUMB WHILE HOLDING THE HOOK PIECE WITH YOUR INDEX FINGER AS SHOWN IN FIGURE 11 YOU SHOULD SEE THE HOOK SPRINGS PROTRUDING FROM THE OTHER END OF THE HOOK PIECE ALLOWING YOU TO SLIDE THE HOOK ALONG THE LOCKING PIECE FREELY TOUCH PANEL USER MANUALREV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 19 4 4 INSTALLING THE ADJUSTABLE HOOK ONTO THE FINEIR TOUCH PANEL BEZEL FIGURE 12 ILLUSTRATES HOW TO INSTALL THE ADJUSTABLE HOOKS ONTO THE BEZEL FIGURE 12 Adjustable hook ENSURE THAT THE LOCKING MECHANISM IS FACING INWARD THEN ATTACH THE HOOKS ONTO THE BEZEL CLAMP PIECE WITH SCREWS ON THE TOP LEFT AND RIGHT SIDES OF THE BEZEL FOLLOWING STEPS 1 AND 2 AS SEEN IN FIGURE 12 ENSURE THAT THE SCREWS ARE NOT FASTENED TO TIGHTLY OTHERWISE THE CLAMP PIECE WILL NOT ABLE TO MOVE FREELY ALONG THE BEZEL THIS STEP IS CRITICAL TO CORRECTLY MOUNTING THE FINEIR TOUCH PANEL ONTO YOUR DISPLAY TOUCH PANEL USER MANUAL REV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 20 4 5 MOUNTING THE TOUCH PANEL ONTO THE DISPLAY BY ADJUSTABLE HOOK WHEN MOUNTING THE PANEL IT IS RECOMMENDED THAT IT BE CARRIED BY TWO PEOPLE FOR SIZES
7. LASS OVERLAY FOR THE FINEIR TOUCH PANEL FIGURE 6 7 7 Glass 74 24 E a 31355 overlay Touch frame Back View IF YOU PLAN TO USE THE ADJUSTABLE HOOK METHOD TO INSTALL THE TOUCH PANEL TO YOUR DISPLAY THE SIZE OF THE GLASS OVERLAY MUST BE AT LEAST 8 9 SMALLER THAN THE SIZE OF THE PANEL ON ALL 4 SIDES USING ADHESION THEN THE GLASS OVERLAY CAN BE THE SAME SIZE AS THE PANEL 3 3 ATTACHING THE GLASS OVERLAY BY ADHESION FIGURE 7 ILLUSTRATES THE GLASS OVERLAY ADHESION PROCESS FIGURE 7 CORRECTLY INSTALL THE GLASS OVERLAY FOLLOW THE STEPS BELOW gt CLEAN UP THE SURFACE OF THE BEZEL AS WELL AS THE GLASS BEFORE APPLYING THE ADHESIVE ALCOHOL ACETALDEHYDE FORMALDEHYDE IS USED FOR CLEANING WATER MUST BE USED TO CLEAN UP THE ALCOHOL AGENT FROM THE SURFACE OF THE BEZEL OTHERWISE THE ADHESIVE MAY DEGRADE QUICKLY AND CAUSE THE BONDING TO FAIL CONTINUED ON NEXT PAGE TOUCH PANEL USER MANUAL REV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 15 gt APPLY THE ADHESIVE TO THE BACK SIDE BEZEL FOLLOWING STEP 1 AS SHOWN IN FIGURE 7 gt ADHERE THE GLASS OVERLAY ON TO THE BACK SIDE BEZEL FOLLOWING STEP 2 AS SHOWN IN FIGURE 7 gt APPLY CONSTANT PRESSURE EVENLY ON THE GLASS BY LEAVING WEIGHTS SUCH AS BOOKS AS SHOWN IN FIGURE 8 FIGURE ILLUSTRATES HOW PRESSURE SHOULD BE APPLIED ON THE GLASS
8. TING RESULTS INCORRECT INTEGRATION OF THE GLASS OVERLAY COULD CAUSE UNSAFE OPERATION THEREFORE THESE GUIDELINES SHOULD BE STRICTLY FOLLOWED INTEGRATION DIAGRAMS OUTLINED IN THIS SECTION ARE FOR REFERENCE ONLY AND ARE NOT TO SCALE IMPORTANT gt IS RECOMMENDED THAT YOU DO A SIMPLE CONNECTION TEST OF THE TOUCH PANEL AFTER IS ASSEMBLED TO MAKE SURE THAT IS IT FUNCTIONING PROPERLY BEFORE ATTACHING THE GLASS OVERLAY F IT IS NOT FUNCTIONING PROPERLY THEN YOU MUST CHECK THE CONNECTIONS OF PIN UNTIL THE PANEL PASSES THE CONNECTION TEST gt FOLLOW THE STEPS IN SECTION 4 7 TO CONNECT THE TOUCH PANEL TO YOUR COMPUTER THEN INSTALL THE TOUCH CONTROL SOFTWARE DETAILED IN SECTION 5 TO DO A CONNECTION TEST WARNING gt ADHESIVE MUST BE LEFT DRY FOR AT LEAST 12 HOURS BEFORE INSTALLING THE TOUCH PANEL ONTO YOUR DISPLAY OTHERWISE THE TOUCH PANEL COULD OPERATE IN AN UNSAFE MANNER gt EVENLY DISTRIBUTE PRESSURE ONTO THE GLASS WHEN APPLYING THE ADHESIVE gt GLASS THICKNESS OF AT LEAST SMM IS RECOMMENDED FOR PANEL SIZES OVER 42 gt TEMPERED GLASS IS RECOMMENDED TO ACHIEVE THE HIGHEST SAFETY STANDARD 3 1 NECESSARY PARTS FOR INTEGRATING THE OVERLAY l 2 3M VHB ADHESIVE TAPE PIECE OF TEMPERED GLASS CUT WITH THE CORRECT DIMENSIONS TOUCH PANEL USER MANUAL REV 1 8 FINEIR TOUCH CONTROL SOFTWARE VERSION 2 1 USB 14 3 2 GLASS OVERLAY SIZE REQUIREMENT FIGURE 6 DETAILS THE REQUIRED SIZE OF THE G

Untitled

Contents

Download Pdf Manuals

Related Search

Related Contents