Multi-port Coax + 2-port 10/100/1000T + 2
Contents
1. 2 port 100 1000X SFP Long Reach PoE over Coaxial Managed Switch LRP 1622CS 16 port Coax 2 port 10 100 1000T 2 port 100 1000X SFP Long Reach PoE over Coaxial Managed Switch LRP Managed Switch is used as an alternative name in this Quick Installation Guide Open the box of the LRP Managed Switch and carefully unpack it The box should contain the following items The LRP Managed Switch x 1 Quick Installation Guide x 1 Rubber Feet x 4 Power Cord x 1 RS232 to RJ45 Console Cable x 1 SFP Dust Cap x 2 BNC Female Dust Cap x 8 LRP 822CS BNC Female Dust Cap x 16 LRP 1622CS Warning Sticker x 8 LRP 822CS Warning Sticker x 16 LRP 1622CS Rack mount Accessory Kit x 1 If any item is found missing or damaged please contact your local reseller for replacement 3 E 2 Requirements Workstations running Windows XP 2003 Vista 7 8 2008 MAC OS X or later Linux UNIX or other platforms are compatible with TCP IP protocols Workstations are installed with Ethernet NIC Network Interface Card Serial Port Connection Terminal gt The above Workstations come with COM Port DB9 or USB to RS 232 converter gt The above Workstations have been installed with terminal emulator such as Hyper Terminal included in Windows XP 2003 gt Serial cable one end is attached to the RS232 serial port while the other end to the console port of the LRP Managed Switch Ethernet Port Connection2. Y Critical Enable Profile 1 a Critical Enable Profile 1 v Critical Enable Profile 1 v Critical Enable Profile 1 v Critical Enable Profile 1 Y Critical Enable Profile 1 v Critical Pro le1 v Critical 3 Loose the BNC male connector gently 4 Pull out the coaxial cable gently 41 LRP 822CS 1 PoE PT Camera LRP 101CE Caution Never pull out the coaxial cable without disabled Long Reach Power over Ethernet function for the port from WebUI Directly pulling out the coaxial cable could damage the Long Reach Ethernet coaxial extender and the BNC female connector of the LRP Managed Switch 1 The package contains warning stickers which should be stuck on the coaxial cable connector before using PLANET LRP 822CS LRP 1622CS and LRP extender If connected with Non PLANET LRP series extender equipment it might cause damage to the equipment 2 After LRP PoE port enabled the center pin of the coaxial cable is with electricity Do not touch center pin or connect this end to any non PLANET LRP equipments a 9 Saving Configuration via the Web In the LRP Managed Switch the running configuration file stores in the RAM In the current version the running configuration sequence of running config can be saved from the RAM to FLASH by Sav
3. gt Network cables Use standard network UTP cables with RJ45 connectors gt The above PC is installed with Web Browser and JAVA runtime environment plug in It is recommended to use Internet Explore 8 0 or above to access the LRP Managed Switch If the Web interface of the LRP Managed Switch is not accessible please turn off the anti virus software or firewall and then try it again 3 Terminal Setup To configure the system connect a serial cable to a COM port on a PC or notebook computer and to the RJ45 type of the console port of the LRP Managed Switch PC Workstation with Terminal Emulation Software Managed Switch RS232 to RJ45 Cable Serial Port Figure 3 1 LRP Managed Switch Console Connectivity A terminal program is required to make the software connection to the LRP Managed Switch 1 Run terminal program on the OS 2 When the following screen appears make sure that the COM port should be configured as Baud 115200 COM1 Properties Data bits 8 Patt Settings Parity None F Bits per second Stop bits ge Flow control None Data bite Parity Stop bits Flow control Figure 3 2 COM Port Configuration 5 e 4 Logon to the Console Once the terminal is connected to the device power on the LRP Managed Switch and the terminal will display running testing procedures Then the following message asks to log in user name and pass
4. Multi port Coax 2 port 10 100 1000T 2 port 100 1000X SFP Long Reach PoE over Coaxial Managed Switch LRP 822CS LRP 1622CS Quick Installation Guide Table of Contents 1 Package Contents s 2 cesessideters dndecinannancebiseecetdehevaad acest a ENES 3 2 REQUINGMOMNUS 2s c2cciciccgcsiaancctaespadedetercasesbaradiaceeeniad sarahsgecassantcdanensaneerarandaccdvans 4 3 Terminal SCCU Pp iaiia wsacclgns tenis sntiasanissiantea a aaa Aa iaaa 5 4 Logon tothe Consol Eses e ennaa sarees aonaanennneesy A A 6 5 Configuring IP Address via the Console ssisiriesiiniiiirisuiiiiesiarni iinoa 7 6 Saving the Configuration via the Console ss sessssssssssereserorosrsrssssarensresesrssno 9 Z Starting Web Management sesicstancincasienesactacualnainssteactameanemarenandedueausimeactittiacaateniess 10 8 Starting Long Reach POE COMMUNICAtION cece teeter aa 12 9 Saving Configuration via the WED iii ccscacgateneeserccsentsadeenadeaaeceregncsaedeeiatenes gt 16 10 Recovering Back to Default Configuration cccceececeee testes eee eee eeeneeaeeeneenes 17 11 Customer SUPPOME ss iccicdieiccazeataecancasatenscatencgedtcastseneesanerontendsecensneaneesaaaeteanten 18 1 Package Contents Thank you for purchasing PLANET Multi port Coax 2 port 10 100 1000T 2 port 100 1000X SFP Long Reach PoE over Coaxial Managed Switch The description of this model is shown below LRP 822CS 8 port Coax 2 port 10 100 1000T
5. e Configurations to FLASH function so that the running configuration sequence becomes the startup configuration file which is called configuration save To save all applied changes and set the current configuration as a startup configuration the startup configuration file will be loaded automatically across a system reboot 1 Click Save gt Save Configurations to FLASH to login Configuration Manager Page SAVE LOGOUT REBOOT REFRESH Save Configurations to FLASH Restore to Defaults 2 Press the Apply button to save running configuration to startup configuration Configuration Manager Save Configuration Running configuration O Startup configuration O Backup configuration Startup configuration O Backup configuration 10 Recovering Back to Default Configuration E IP Address has been changed or admin password has been forgotten To reset the IP address to the default IP Address 192 168 0 100 or reset the login password to default value press the hardware reset button on the front panel for about 10 seconds After the device is rebooted you can login the management Web interface within the same subnet of 192 168 0 xx cs 8 Port Lo 1 SYS 7 e 4 LNK RESET pwe a EWR P gt PoE In Use 115200 N 8 1 lt i ie Figure 10 1 LRP 822CS Reset Button PMR ee Con Figure 10 2 LRP 1622CS Reset Button 17 H _ 11 Custom
6. er Support Thank you for purchasing PLANET products You can browse our online FAQ resource and User s Manual on PLANET Web site first to check if it could solve your issue If you need more support information please contact PLANET switch support team PLANET online FAQ http www planet com tw en support faq php type 1 Switch support team mail address support _switch planet com tw LRP 822CS LRP 1622CS User s Manual http www planet com tw en support download php typel 1 amp model amp type 3 Please select your switch model name from the Product Model drop down menu Copyright PLANET Technology Corp 2015 Contents are subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners
7. file 1 Critical Profile 1 Y Critical Profile 1 Y Critical Profile 1 Y Critical Profile 1 Critical Profle 1 Y Critical 5 Check the LNK LED of the Long Reach Power over Ethernet interface on the front of the LRP Managed Switch Ensure that the Long Reach Power over Ethernet interface is operating correctly 1 Before installation please consider the distance and watts value demand for PD devices The LRP Managed Switch and LRP Extender PoE output capacity and upload download performance depend on the length of coaxial cable You can refer to manual chapter 1 5 for the information 2 As there are various resistance values in the category of RG 59 U or RG 6 U cable the actual data rate will vary on the quality of the copper wire and environmental factors E Remove the connected the Coaxial Cable 1 Make sure there is no network activity anymore 2 Disable Long Reach Power over Ethernet function for the all LRP ports from WebuUI SAVE LOGOUT REBOOT REFRESH PoE Schedule PD Alive Check PoE Configuration PoE Configuration System PoE Admin Mode PoE Management Mode Disable Temperature Threshold ir Power Allocation PoE Mode PoE Temperature il Schedule Priority 35 C 95 F Ow 240W Current Used mA Power Used W Enable Profile 1
8. ial Managed Switch PLANET Technology Corporation 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528 Email support planet com tw Copyright 2015 PLANET Technology Corporation All rights reserved Figure 7 3 Web Main Screen of LRP Managed Switch The Switch Menu on the left of the Web page lets you access all the commands and statistics the LRP Managed Switch provides Figure 7 4 Switch Menu Now you can use the Web management interface to continue the Switch management Please refer to the user s manual for more 8 Starting Long Reach PoE Communication The following shows how to start up the Long Reach PoE Communication of the LRP Managed Switch from Web Management The LRP Managed Switch is configured DISABLED Long Reach PoE function as default E Connect the Coaxial Cable 1 Insert the coaxial cable with one side being the 75QBNC plug connector into the Long Reach Ethernet coaxial interface 2 Connect the other end of the cable to a device with Long Reach Ethernet coaxial extender installed 3 Tight the BNC male connector gently PoE PT Camera LRP 822CS LRP 101CE 4 Enable Long Reach Power over Ethernet function for the all LRP ports from WebuUI SAVE LOGOUT REBOOT REFRESH PoE Configuration PoE Configuration Toisanie Profile 1 Y Critical Profile 1 Y Critical Pro
9. in Figure 5 2 LRP series config ip address 192 168 1 100 mask 255 255 255 0 LRP series config ip default gateway 192 168 1 254 7 H The previous command would apply the following settings for the Switch IP Address 192 168 1 100 Subnet Mask 255 255 255 0 Gateway 192 168 1 254 Press any key to continue Username admin LRP series confi ure ngs ecleeteoneial ip address 192 168 1 100 mask 255 255 255 LRP series config ip default gateway 192 168 1 254 Figure 5 2 IP Address Screen 5 Repeat Step 1 to check if the IP address is changed If the IP is successfully configured the LRP Managed Switch will apply the new IP address setting immediately You can access the Web interface of the LRP Managed Switch through the new IP address If you are not familiar with console command or the related parameter enter anytime in console to get the help description 6 Saving the Configuration via the Console In the switch the running configuration file stores in the RAM In the current version the running configuration sequence running config can be saved from the RAM to FLASH by writing the command or copying the running config startup config command so that the running configuration sequence becomes the startup configuration file which is called configuration save 1 At the LRP series prompt enter copy running config startup config as shown in Figure 6 1 Press any key
10. to continue Username admin Password LRP series copy running config startup config Success Figure 6 1 The Configuration Screen 7 Starting Web Management The following shows how to start up the Web Management of the LRP Managed Switch Note the LRP Managed Switch is configured through an Ethernet connection Please make sure the manager PC must be set on the same IP subnet address For example the default IP address of the LRP Managed Switch is 192 168 0 100 then the manager PC should be set at 192 168 0 x where x is a number between 1 and 254 except 100 and the default subnet mask is 255 255 255 0 PC Workstation with Web Browser 192 168 0 x Managed Switch RJ45 UTP Cable IP Address 192 168 0 100 Figure 7 1 IP Management Diagram E Logging in to the LRP Managed Switch 1 Use Internet Explorer 8 0 or above Web browser and enter IP address http 192 168 0 100 to access the Web interface 2 When the following dialog box appears please enter the default user name and password admin The login screen in Figure 7 2 appears Default Username admin Default Password admin Q PLANE tworking amp Commanication Uesrname Password Figure 7 2 Login Screen 3 After entering the password the main screen appears as Figure 7 3 shows Welcome to PLANET LRP 822CS 8 port Coax 2 port 10 100 1000T 2 port 100 1000X SFP Long Reach PoE over Coax
11. word The factory default user name and password are shown as follows and the login screen in Figure 4 1 appears Username admin Password admin Press any key to continue Username admin Password LRP series Figure 4 1 LRP Managed Switch Console Login Screen The user can now enter commands to manage the LRP Managed Switch For a detailed description of the commands please refer to the following chapters 1 For security reason please change and memorize the new password after this first setup 2 Only accept command in lowercase letter under console interface 5 Configuring IP Address via the Console The LRP Managed Switch is shipped with default IP address as follows IP Address 192 168 0 100 Subnet Mask 255 255 255 0 To check the current IP address or modify a new IP address for the Switch please use the procedures as follows E Show the current IP address 1 At the LRP series prompt enter show ip 2 The screen displays the current IP address Subnet Mask and Gateway as shown in Figure 5 1 Press any key to continue Username admin LRP series sho IP Address 192 168 0 100 Subnet Netmask 255 255 255 0 Default Gateway 192 18 O 254 Figure 5 1 IP Information Screen E Configuring IP address 3 At the LRP series prompt enter configure 4 At the LRP series config prompt enter the following command and press lt Enter gt as shown
Download Pdf Manuals
Related Search