Vicmarc Grinding System User Manual
Contents
1. of the guards in this manual have been removed for photographic purposes Always use the guards as supplied and specified with your grinder Please note the following setting up instructions are a guide only Personal grinding setting can be achieved by adjusting the positions and angles to suit your own preferences Page 3 Setting up your Grinder 200mm Diameter Depth Gauge 167 5mm for Vicmarc naa 1 Place your grinder on your bench 70mm back and parallel with the front edge of your bench 2 Line up slide assemblies so that the centre of the slide plates are in line with the centre of the grinding wheels and protrude 20mm forward of your bench top See diagram above Ensure they are also square to the bench 3 Mark the 4 screw holes on your bench for the base of the grinder and the 4 holes for each slide Also mark the outline of the base of the grinder on your bench 4 Remove the grinder and the slides and drill the holes to match the mounting screws you are going to use for the grinder and the slides 5 Mount the slides by inserting the screws Before tightening ensure the slides are square to the front edge of your bench and parallel to each other 6 Place the grinder in place using the marked outline as a reference Ensure the grinder is parallel to the bench and the slides are centred with the grinding wheels 7 Tighten the screws ensuring the grinder is fastened to the bench 8 Check again that2. the grinder is square to the bench the slides are centred with the wheels are square to the bench and parallel with each other 9 Screw the Depth Gauge to the centre of the bench top 10 Your setup is complete Page 4 Setting up your Grinding Rest Use the Grinding Rest to grind this angle 1 To initially shape the top angle of the bowl gouge place the Vicmarc Quick Tool Setter so that both radii contact the grinding wheel as shown below 2 Then adjust the Grinding Rest to meet flush with the bottom of the Vicmarc Quick Tool Setter as shown below Lock the table and the bottom slide in place Make sure that the table does not touch the wheel There should be approximately 2mm clearance between the wheel and the rest Sharpening Jig Quick Tool Setter Both radii touching at the same p l time 7 OS Quick Tool Setter flush with Grinding Rest The Grinding Rest Quick Tool Setter can be used to set and erind other popular angles 22 33 44 amp 66 To set the desired angle place the Grinding Rest tool setter numbers facing the right hand side as shown with the text flat on the Grinding Rest and both radii touching the wheel Page 5 3 Place your gouge upside down on the rest and grind the top of the tool away until it meets the bottom of the flute This pregrind makes your tool look like the profile below 4 Important Make sure that the tool does not get too hot and change
3. 07 3283 4656 NN Int Ph 61 7 3284 3103 Int Fax 61 7 3283 4656 Email vicmarc vicmarc com Web www vicmarc com Page 12
4. Vicmarc Grinding System User Manual 4 i a n eG j o pm F J hl F S j Vicmarc Sharpening Jig Vicmarc Grinding Rest Part No V00437 Part No V00438 Vicmarc Machinery Pty Ltd yvN Manufacturer of Quality Woodturning Lathes and Accessories Vicmarc Machinery Pty Ltd 52 Grice Street Clontarf QLD 4019 Australia Phone 07 3284 3103 Fax 07 3283 4656 Int Ph 61 7 3284 3103 Int Fax 61 7 3283 4656 Email vicmarc vicmarc com Web www vicmarc com Manufacturer of Quality Woodturning Lathes Chucks and Accessories Vicmarc Machinery a family owned and operated business has been manufacturing woodturning lathes and accessories for the hobbyists and professionals since 1984 The company is dedicated to providing machinery of the highest quality and precision engineering that has secured sales worldwide Through constant improvement Vicmarc retains its place as a leader in the field Vicmarc lathes chucks and accessories are known and respected internationally for their robust design and ease of use Only the best materials and latest high precision computer controlled machinery are used in the manufacture of Vicmarc products The company continues to respond to the demands of the market updating and improving all stages of manufacture Contents Description sitscccniwsce sctcewse toneetecinenece cewue beswecanstceueeancwess 3 Salety INMMPOMMAUON a snscr unde nin roni E EE RSE 3 Se
5. chinery manufacturer of Vicmarc machine tools hereby guarantee the purchaser of the Grinding System that it was precision engineered from the finest materials available and was thoroughly inspected and tested before leaving the factory If within 12 months following the date of delivery the product is proven to have been defective because of faulty materials or workmanship Vicmarc Machinery will repair or replace the product free of charge This guarantee 1s subject to the following conditions l 2 The product shall be returned to Vicmarc Machinery within 12 months with a brief description of the complaint The name and address of the purchaser together with the date of purchase and supplier details shall accompany the parts Vicmarc Machinery will accept no responsibility whatsoever under the guarantee or otherwise if the product is not used strictly in accordance with the instructions supplied or if the fault can reasonably be explained by carelessness or negligence The purchaser is responsible for all costs incurred in transport and packaging to and from Vicmarc Machinery In the case of accident liability 1s expressly excluded when the product is tampered with or altered without authorization Overseas purchasers are advised to obtain local guarantees from their Vicmarc agent Conditions may vary to those detailed above Vicmarc Machinery Pty Ltd 52 Grice Street Clontarf QLD 4019 Australia Phone 07 3284 3103 Fax
6. colour brown or blue as this will reduce the hardness of the metal and shorten the life of the tool To prevent this make sure you periodically dip the tool in water If you find the tool heating up too quickly then you may need to re dress your wheel or apply less pressure on the grinding wheel Page 6 Setting up your Sharpening Jig 1 To set up for a 55 grind place the Vicmarc Quick Tool Setter into the pivoting point Then slide the slide plate out so that the two radii on the gauge on the 55 angle side both touch the grinding wheel Then lock the slide plate into position Pivoting point Both radii touching at the same time 2 Place your bowl gouge into the Sharpening Jig and set it to protrude 55mm by using the Depth Gauge as shown below Lock the gouge into position by tightening the black hand knob Page 7 3 Line up the angle on the Sharpening Jig to the 55 mark as shown below This is done by holding the jig locating bar and the gouge and manually adjusting the angle Note Do not loosen the nuts and bolts for this adjustment For additional friction for the locating bar tighten this nut Angle indicators 33 amp 55 Jig locating bar 4 Place the Sharpening Jig in the pivoting point and swivel from side to side until you have roughed out the bevel profile and removed most of the material Rotate the Jig constantly from right to left to avoid flat spots and overheating Gouge rou
7. est The triangle slide gauge has some pre set angles to enable you to grind precise angles as shown below 55 55 35 90 The below angles can be set using the Grinding Rest Quick Tool Setter as shown on Page 5 Skew Chisels 22 Parting Tools 33 amp 44 Set the rest to 33 and then set the triangle Set the rest to 33 or 44 and then place the gauge to the angle of your skew chisel To chisel against the rest To sharpen simply slide sharpen simply slide the triangle gauge along the triangle gauge along the tool slide the slide Vy Straight Edge Scraper 66 Roughing Gouge amp Round End Scraper Place the triangle on 90 and rest the scraper 66 along the triangle Move the scraper from Set the rest to 66 then rotate the roughing gouge or left to right to grind the front angle of the pivot the round end scraper on the rest to grind the scraper bevel Page 11 Maintenance To ensure your grinding system works to the best of its ability you should dress the grinding wheels when they become dull or dirty do not dress CBN Grinding wheels By dressing the wheels you get a smoother and quicker grind and a sharper finish As less heat is generated your tool will stay sharper for longer It is also important to keep the grinding system clean of grit and debris as this can jam the adjusting mechanisms and make setting up for different tools difficult The Vicmarc Guarantee Vicmarc Ma
8. ghed out on one side 5 Important Make sure that the tool does not get too hot and change colour brown or blue as this will reduce the hardness of the metal and shorten the life of the tool To prevent this make sure you periodically dip the tool in water If you find the tool heating up too quickly then you may need to re dress your wheel or apply less pressure on the grinding wheel Page 8 6 Continue grinding your tool on the finer grit wheel 120 180 grit recommended to achieve a sharp cutting edge After you finish grinding your bowl gouge should look like the profile below 7 You can check your bowl gouge angles using the Vicmarc Quick Tool Setter as shown below With this tool setter you can achieve perfect angles for bowl gouges 55 and spindle gouges 33 Page 9 Additional Grinding Shapes Sharpening Jig Different tools require different methods of sharpening below is a list of the most common tools used in woodworking and some suggested angles for sharpening them Please note these angles given are based on the Vicmarc Manta Gauge angles and are recommended as the best angles from years of sharpening experience but they should only be taken as a suggestion Spindle Gouge 55 By using a tool gauge such as the Vicmarc Manta Gauge or similar you can measure and adjust your grinding system to achieve all of your desired angles Manta Gauge part number V00818 Page 10 Grinding R
9. tting up your Grinder cece rnan ee SONTE 4 Setting up your Grinding Rest cece cece c cence eee e eee eens 5 Setting up your Sharpening Jig ccc cece ccc cece cece ene e eens 7 Additional Grinding Shapes c cece cece cece eee eeeeneeeseeas 10 IVFEWEVEC TAIN Ctarsntccccron sete d vo ioinmaeneese ETERA TET Ere tinted 12 The Vicmarc Guarantee ccc ccc cece cee e eee eeeeee ee eeeeneeees 12 Page 2 Description The Vicmarc Grinding system has been designed to make shaping and sharpening your tools quick and easy With standard angle gauges and multiple adjustment positions you get an excellent and consistent grind every time Important when grinding V10 or any other High Speed Steel tools you must make sure that the tool doesn t get too hot and change colour brown or blue as this will weaken the steel and shorten the life of your tool You should periodically dip the tip of the tool in water when it begins to get warm but before it gets hot Safety Information l Read and understand this instruction manual before operating the Grinding System Always wear eye protection Do not wear neckties jewellery or loose clothing Do not operate without guards in place Tighten all handles before operating Make sure the grinder is off and has stopped rotating before making any adjustments Do not operate while under the influence of drugs alcohol or medication Some
Download Pdf Manuals
Related Search