Home
CH4100 Series High Efficiency Intelligent Charger ThunderStruck
Contents
1. CH4100 Series High Efficiency Intelligent Charger ThunderStruck User Manual Ver 1 02 Table Of Contents I Product Overview II Safety II Preventing Leakage and Fire 1 Correct use of Breakers Sockets and Cables 2 Correct Use of Input Connections 3 Charging Environment Requirements IV Regular Maintenance V Technical Specifications VI Parts List VII LED Charge Light Information VIII Appearance and Installation Dimensions IX Connections and Wiring X Faults amp Solutions I Product Overview The CH4100 series high efficiency intelligent charger is designed to charge traction batteries of electric vehicles This series of products adopt the most advanced technologies such as LLC resonant active power factor correction microcomputer measurement and control digital adjusting and extremely water resistant technology Its features include wide input voltage range high input power factor that significantly reduces the input current as well as heat generated from the input cable and Low harmonic current that reduces interference to other electric equipment Full range soft switching is used to achieve high conversion efficiency and very little electromagnetic interference The charger is designed according to IP66 protection grade and is highly water resistant It is also small in size lightweight quiet beautiful simple to install and of course easy operation and maintenance The charger uses microcomputer measurements and
2. control technology the embedded CPU can accurately detect battery voltage and charge current The charger has temperature compensation functions as well as automatic shut down after being fully charged Reverse battery connection protection as well as output short circuit protection AC input under voltage protection and overheating protection These functions help to ensure safe and reliable use II Safety 1 Please do not disassemble the charger this may cause electric shock or other injuries 2 Ifthe charger needs to be connected to an AC power supply with extension cables please make sure that the extension cable can withstand the maximum input current GB 2 5mm2 copper core cable is recommended to be used and limit the extension cable length within 10m 3 Don t place the charger where it can get wet this may cause damage to the charger as well as electric shock to the operator 4 The charger s DC output plug should be connected reliably to the socket if they are damaged or loose please replace them immediately otherwise it will cause overheating in the plug position and can even cause fire 5 If the charger produces any abnormal sound or smell while on please unplug the power immediately and contact the service department Do not attempt to open the case of charger 6 Make sure that all air vents are unobstructed to prevent charger overheating Do not place the charger near a heat source the charger should be left wi
3. ctly you can refer to the table below Battery External battery temperature temperature sensor is Check sensor connection or change a new one Sensor Fault fault or not connected Battery is not connected or reverse Check and connect the battery correctly connected Charging environment temperature is too Place the charger in lower temperature environments high cooling fan is and retry fault Check whether cooling fan is at fault or air vents are air vents are obstructed obstructed Poor contact of charger s input side Charger is broken us Charging Battery 1s damaged or Check and replace battery timeout aging Battery Battery 1s damaged or Check and replace battery Overheating aging Battery is damaged or Check and replace battery timeout aging Internal temperature sensor fault Output voltage Charger is broken feedback fault inside Please contact us Battery is broken Full Power Poor contact between after charger and battery short charging Battery has been fully Battery not connected Over temperat ure protection Input fault protection If no poor contact phenomenon occurs please contact Charger is broken eee Please contact us inside Check whether the battery is damaged battery connecting cables are firm the battery is fully charged Battery is aging Battery voltage is lower than the nominal voltage of the Battery temperature becomes more than 50 C C
4. heck the battery and replace bad battery Reselect charger that match battery voltage level Low battery capacity after Battery is aging Replace the battery fully charging Cables are too long or too thin Between the Reduce the output cables back to initial length charger and batte Charging time becomes too short or too long Charger overheating Check if there are foreign matters around the fan and protection remove them Battery is aging Replace the battery COO Coo Check whether the cooling fan is working correctly or contact us to replace the fan Connectors are not LED indicator connected firmly or lights but no the polarity is Connect all connectors correctly and recharge charging reversed Battery is disconnected o Battery is broken Replace your battery with a new batte LED indicator AC input is not JE doesi thieht ER Check AC power supply and chargers input cables Charger is broken Please contact us inside If your charger still does not work correctly after referencing the above list please record the state of the fault and charge indicator information then contact us
5. lt 40dB Seismic rating Designed according to IEC60335 2 29 2004 Part 21 Working temperature 25 55 C Note models whose output power greater than 2K W Storage temperature 40 80 C Recognition certificates CE SGS will ensure 2K W output at 60 C VI Parts List A AC Input Cables B DC Output Cables C Signal Cables D Charging Indicator E Mounting plate F Shell G Cooling Fan and Fan Cover VII LED Charge Light Information Green Light Flashing It is Charging Normally Flashing Yellow Red and Green in Various Charging has recently stopped or has a Orders Fault with Charger or Batteries Contact Thunderstruck ev com VIII Appearance and Installation Dimensions Do not bend the wires coming out of the charger until they have at least 50mm of space from where they enter the shell of the charger 272 210 Insure that there is a 50mm gap above the charger to allow for proper ventilation IX Connections and Wiring Input Cables Terminal Model DJ7031 4 8 11 Direction of view form the cables to terminal Terminal Model for DJ7031 4 8 21 matching Wire Calor wire core diameter brown 20mm tive wie tive 25mm N Neutral wire Yellow 3 2 5 mm PE Protective grounding wire and green Output Cables O wre Calor Wire coe diameter ps wt mm ouputpositvepote tae mm output negative pote X Faults and Solutions If your charger is not working corre
6. mable objects 4 Lithium Safety A lithium battery pack should have a battery management system to ensure safe charging A battery pack with no BMS can be a very dangerous thing We are not responsible for damage to batteries due to using a charger with no BMS Most prismatic lithium batteries should be contained in a manner that prevents them from swelling during charging and discharging Consult your battery manufacturer s recommendation for the best way to package your cells IV Regular Maintenance 1 Check the J1772 Socket regularly for corrosion or other conduction inhibitors Poor contact may result in overheating and burning inside the socket which although unlikely could cause fire 2 Make sure to use a charger that has a dedicated breaker and wire running to it 3 Make sure that the charger s shell and cooling fan are free of debris and dirt V Technical Specifications Rated input voltage 220VAC 50 60Hz Input voltage range 85 265VAC Note When the Input voltage is lower than 185VAC the output power will be limited to 1 5K W Power Factor gt 0 99 220VAC input full power output Total Harmonic Current lt 5 220VAC input full power output Nominal output voltage 144V Maxim output voltage 180V Rated output current 15A Voltage regulation accuracy lt 0 5 Current regulation accuracy lt 2 Conversion efficiency gt 95 220VAC input full power output Protection class IP66 Audible Noise
7. th enough space to ensure proper ventilation 7 Please disconnect the charger s AC input power if you need to move it 8 Make sure that AC power supply voltage matches chargers input voltage For inquiries please contact your supplier or local power Supply Corporation 9 Battery voltage and the nominal voltage of the charger must be matched or it could damage both the charger and the batteries 10 To avoid damage to the charger s cables do not pull twist or shake the cables or the connection terminals If the cable is worn please replace it immediately II Preventing Leakage and Fire 1 Correct use of Breakers Sockets and Cables 1 Use copper core cables with flame retardant jackets The cables core diameter must be at least 2 5mm in diameter 2 Prevent plugs sockets from coming in contact with water Note According to statistics 80 of electric car fires occur during charging The main reasons for this include insufficient core diameter size of cables poor quality plugs and sockets poor contact of plugs and sockets poor flame retardant sheath or shells of breakers plugs and sockets and so on 2 Correct Use of Input Connections Make sure that the plug is clean undamaged and free of dirt before charging 3 Charging Environment Requirements Have it be spacious and away from flammable materials Avoid mounting placing the charging plugs charging cables or the charger itself on car cabs synthetic seats and other flam
Download Pdf Manuals
Related Search
Related Contents
TECHNIQUES D`EMBALLAGE AMX MVP-WDS Olympus PEN Street M Copyright © All rights reserved.
Failed to retrieve file