User Manual - Music Direct
Contents
1. e Connect to the corresponding optical or coaxial digital output of sources such as CD or BD DVD players digital cable box digital tuners and other applicable components 14 AC MAINS INPUT e The D3020 comes supplied with a separate detachable mains power cord Before connecting the plug to the mains power source ensure that it is firmly connected to the D3020 s AC Mains input socket first e Always disconnect the mains power plug from the mains power source first before disconnecting the cable from the D3020 s AC Mains input socket IDENTIFICATION OF CONTROLS F gt REMOTE CONTROL 1 ON Switch D3020 from Standby mode to operating mode 2 OFF Switch D3020 to standby mode 3 Increase or decrease audio level 4 lt P Select source ee y 5 TUNER CONTROLS applicable for NAD products with Tuner section lt lt PPI Step Up or down Presets gt II Select applicable Tuner bands BATTERY INSERTION PROCEDURE 3 Place the supplied CR2025 battery into the tray Ensure the symbol is 1 Insert a hooked tip into the battery door release hole facing upwards 4 Slide the tray back until it clicks into place 2 Slide out the battery tray OTHER FEATURES CONNECT TO BLUETOOTH DEVICE Pair Bluetooth device with the unique device ID of D3020 D 3020 010DD3 in this example Start playback of Bluetooth device upon successful pairing Biuetooth Bluetooth2. gt AUX 1 AUX 2 USB device gt USB Other sources gt Bluetooth Using applicable connectors not supplied connect the digital audio input and analog audio input ports to the corresponding audio input sockets of other devices like receivers amplifiers audio processors or music system Connect corresponding end of the mains power cord to the AC mains input of the D 3020 and the plug connected to a mains power source With all applicable sources hooked up with D 3020 and powered up press Standby to switch ON the D 3020 from standby mode Start listening to your preferred Source by repeatedly pressing S to cycle through the Sources OPTICAL 1 OPTICAL 2 COAXIAL USB AUX 1 AUX 2 and BT and select desired Source 1 4 6 7 IDENTIFICATION OF CONTROLS ANALOG AUDIO INPUT SPEAKERS H Serial No N de s rie W STANDBY e With the corresponding end of the mains power cord connected to the AC mains input of the D 3020 and the plug connected to a mains power source press W Standby to switch ON the D 3020 from standby mode The Standby indicator will turn from amber to bright white color Pressing Standby again turns the unit back to standby mode S SOURCE e Toggle to cycle through the Sources OPT1 OPT2 COAX USB AUX 1 AUX 2 BT and select desired Source VOLUME e Adjus
3. of the cabinet For your future convenience we suggest that you record these numbers here NAD is a trademark of NAD Electronics International a division of Lenbrook Industries Limited Copyright 2013 NAD Electronics International a division of Lenbrook Industries Limited INTRODUCTION GETTING STARTED UNPACKING AND SETUP WHAT S IN THE BOX Packed with your D 3020 you will find Detachable mains power cord Remote control with 3V CR2025 battery TOSLINK mini adapter Four pieces of dome shaped feet Quick Setup Guide SAVE THE PACKAGING Please save the box and all the packaging in which your D 3020 arrived Should you move or otherwise need to transport your D 3020 this is by far the safest container in which to do so We ve seen too many otherwise perfect components damaged in transit for lack of a proper shipping carton so please Save that box QUICK SETUP This simple guide will help you get started with your D 3020 Place the D 3020 on a firm level surface Do not place the unit on a soft surface like a carpet Make all the connections to your D 3020 with the unit unplugged from the mains power source It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections Using applicable connectors not supplied connect source devices to corresponding input sockets of D 3020 S PDIF sources gt OPTICAL 1 OPTICAL 2 COAXIAL Analog sources
4. LINES STAND OFF ae md IMEULATORS SERVICE 7 oe ENTRANCE hay CONDUCTORS HET it r i T r E j he MAST ne j a aa j F ANTENNA SERVICE ENTRANCE Jonounn cLaues n LEADAN AE EGuUIPMENT T GROUND WIRE P Had A A J of ANTENNA E Eaa DISCHARGE unit amp POWER SERVICE ananos ile tne apoun ECTRODE SYSTEM i E i Liernin otal waler pipe BONDING JUMPER S TERMA S GROUND TERMINALS CLAMPS OF PRODLT _ OPTIONAL ANTENNA GROUND iid ELECTRODE DRIVEN amp FEET 3AL INTO THE ESAT IF py Bir LOCAL CODES E WEC SECTION Mozi ik 15 Lightning For added protection for this product during a lightning storm or when itis left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 16 Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 17 Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 18 Object and Liquid Entry Never push objects of any kind into
5. terminals marked R and R ensuring that the R is connected to the terminal on your loudspeaker and the R is connected to the loudspeaker s terminal Connect the left speaker to the terminals marked L and L ensuring that the L is connected to the terminal on your loudspeaker and the L is connected to the loudspeaker s terminal 11 12V TRIGGER IN e Connect this 12V Trigger input to the remote device s corresponding 12V DC output jack using a mono cable with 3 5mm male plug The controlling device must be equipped with a 12V trigger output to use this feature IDENTIFICATION OF CONTROLS 12 USB e Asynchronous USB 24 bit 96 kHz input assures lowest jitter for best musical performance e Using Type A to Type B cable connector not supplied interface computer audio to this asynchronous Type B USB input to directly stream 24 96 PCM content from your PC or MAC e Ensure that the Sound or Audio device setting of your computer is set to NAD USB Audio MINIMUM PC SYSTEM REQUIREMENT Microsoft Windows XP Service Pack 2 or higher Microsoft Windows 7 FOR MAC USERS Minimum Mac OS X Snow Leopard version 10 6 and later versions NOTE Download and install to your PC the NAD USB Audio driver from the Manuals Downloads tab of the NAD web address http nadelectronics com products digital music D 3020 Hybrid Digital Amplifier 13 DIGITAL AUDIO INPUT OPT1 OPT2 COAXIAL
6. D3020 Hybrid Digital Amplifer Owner s Manual IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR LATER USE FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO EQUIPMENT 1 Read instructions All the safety and operating instructions should be read before the product is operated 2 Retain instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the product and in the operating instructions should be adhered to 4 Follow Instructions All operating and use instructions should be followed 5 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Clean only with a dry cloth 6 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards 7 Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 8 Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting ac
7. Devices gt D3020 010DD3 D7050 BT 010DBi VISO1 AP DF8036 Not Connected Not Connected Not Connected Now Discoverable Biuetooth Bluetooth Devices D3020 010DD3 D7050_BT 010DB1 VISO1 AP DF8036 Connected Not Connected Not Connected Now Discoverable FEET INSTALLATION GUIDE The dome shaped feet are supplied for optional installation Install the feet as per suggested locations below You may generate a template for proper placement of the feet 3 e w oe NOTE The feet can only be installed in the format shown above e Ensure that with the feet installed the D 3020 is stable balanced and will not tip over AUDIO SPECIFICATIONS Rated power at 8 ohms IHF Dynamic Power 8 ohms IHF Dynamic Power 4 ohms IHF Dynamic Power 2 ohms Signal to Noise ratio A weighted Channel separation 1 kHz Channel separation 10 kHz Channel balance Frequency response 20 Hz 96 kHz Total Harmonic Distortion Maximum input level IMD SMPTE IMD CCIF GENERAL SPECIFICATIONS Standby power Supports bit rate sample rate Unit dimensions W x H x D Gross Shipping weight SPECIFICATIONS 30W 65W 105W 150W gt 90 dB gt 75dB gt 65 dB 0 0 3 dB 0 dB to 0 3 dB lt 0 03 5V 0 02 0 003 lt 0 5W up to 24 96 58 x 186 x219 mm 2 5 16 X 7 3 8 Xx 8 5 8 inches 2 1 kg 4 6 Ibs NAD SHALL NOT BE HE
8. ITUTE A RISK OF ELECTRIC SHOCK TO PERSONS THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE SERVICING INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user s authority to operate this equipment CAUTION REGARDING PLACEMENT To maintain proper ventilation be sure to leave a space around the unit from the largest outer dimensions including projections that is equal to or greater than shown below Left and Right Panels 10 cm Rear Panel 10 cm Top Panel 10 cm NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment The symbol on the product user s manual and Packaging point this out The materials can be reused in accordance with their markings Through re use recycling of raw materials or other forms of recycling of old products you are making an important contribution to the protection of our environment Your local admi
9. LD LIABLE FOR ANY TECHNICAL OR USER INTERFACE DISCREPANCIES IN THIS MANUAL THE D 3020 OWNER S MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE CHECK OUT WWW NADELECTRONICS COM FOR THE LATEST VERSION OF THE D 3020 OWNER S MANUAL www NADelectronics com 2013 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved NAD and the NAD logo are trademarks of NAD Electronics International a division of Lenbrook Industries Limited No part of this publication may be reproduced stored or transmitted in any form without the written permission of NAD Electronics International While every effort has been made to ensure the contents are accurate at the time of publication features and specifications may be subject to change without prior notice D3020_ENG_OM_V03 JUL 2013
10. cessory recommended by the manufacturer 9 A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product wae and cart combination to overturn 10 Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 11 Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company The primary method of isolating the amplifier from the mains supply is to disconnect the mains plug Ensure that the mains plug remains accessible at all times Unplug the AC power cord from the AC outlet if the unit will not be used for several months or more 12 Grounding or Polarization This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to inse
11. e same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards IMPORTANT SAFETY INSTRUCTIONS 21 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition 22 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer 23 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat 24 Headphones Excessive sound pressure form earphones and headphones can cause hearing loss 25 Battery Disposal When disposing of used batteries please comply with governmental regulations or environmental public instruction s rules that apply in your country or area Batteries battery pack or batteries installed must not be exposed to excessive heat such as sunshine fire or the like WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED DANGEROUS VOLTAGE WITHIN THE PRODUCT S ENCLOSURE THAT MAYBE OF SUFFICIENT MAGNITUDE TO CONST
12. nistrative office can advise you of the responsible waste disposal point INFORMATION ABOUT COLLECTION AND DISPOSAL OF WASTE BATTERIES DIRECTIVE 2006 66 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF EUROPEAN UNION FOR EUROPEAN CUSTOMERS ONLY Batteries bearing any of these symbols indicate that they should be treated as separate collection and not as municipal waste It is encouraged that Pb necessary measures are implemented to maximize the separate collection of waste batteries and to minimize the disposal of batteries as mixed municipal waste Hg Cd End users are exhorted not to dispose waste batteries as unsorted municipal waste In order to achieve a high level of recycling waste batteries discard waste batteries separately and properly through an accessible collection point in your vicinity For more information about collection and recycling of waste batteries please contact your local municipality your waste disposal service or the point of sale where you purchased the items By ensuring compliance and conformance to proper disposal of waste batteries potential hazardous effects on human health is prevented and the negative impact of batteries and waste batteries on the environment is minimized thus contributing to the protection preservation and quality improvement of the environment RECORD YOUR MODEL NUMBER NOW WHILE YOU CAN SEE IT The model and serial number of your new D 3020 are located on the back
13. rt the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug 13 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product 14 Outdoor Antenna Grounding f an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer s attention to Section 820 40 of the NEC which provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical A pne GROUND CLAMP a il a POWER
14. t audio level by turning clockwise or counterclockwise DISPLAY e lluminate the selected or active Source OPT1 OPT2 COAX USB AUX 1 AUX 2 BT and current audio level PHONES e A3 5 mm stereo jack socket is supplied for headphone listening Specially designed low noise headphone circuitry can accommodate a wide range of phones even 600 Ohm studio models e Ensure that the volume control is turned to minimum fully counterclockwise before connecting or disconnecting headphones Listening at high levels can damage your hearing e Inserting a headphone jack into this socket automatically switches off the loudspeakers BASS EQ e Boost overall bass response by at least 6 dB BASS is illuminated in the display with BASS EQ enabled e Toggle to enable or disable BASS EQ AUX 1 e Use a twin RCA to RCA lead to connect these sockets to the left and right analog output of a CD player preamplifier processor or other applicable devices 8 AUX2 e Connect to corresponding output connectors of other audio devices using a 3 5mm stereo plug not supplied This input also accepts headphone digital audio output from a MacBook Pro e Install the supplied TOSLINK mini adapter to convert this input into an additional digital optical input OPT2 9 SUBW e Connect the SUBW output to powered active subwoofers or to power amplifier channels driving a passive system 10 SPEAKERS e Connect the right speaker to the
15. this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product WARNING THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND OBJECTS FILLED WITH LIQUIDS SUCH AS VASES SHOULD NOT BE PLACED ON THE APPARATUS AS WITH ANY ELECTRONIC PRODUCTS USE CARE NOT TO SPILL LIQUIDS INTO ANY PART OF THE SYSTEM LIQUIDS CAN CAUSE A FAILURE AND OR A FIRE HAZARD 19 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c Ifthe product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e Ifthe product has been dropped or damaged in any way f when the product exhibits a distinct change in performance this indicates a need for service 20 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have th
Download Pdf Manuals
Related Search