CE-CC115-W - Clinton Electronics
Contents
1. l AN aesan m agi qa UP button SETUP button RIGHT button DOWN button LEFT button 1 Press the SET button e Settings can now be made The SETUP menu is displayed on the monitor SETUP gt LENS MANUAL SHUTTER ESC 4 WHITE BAL ATW BACKLIGHT OFF AGC LOWe DNR LOW SENS UP OFF SPECIAL EXIT 2 Select a menu item from the list available by using the UP and DOWN buttons e The cursor can be moved up or down by using the UP and DOWN buttons Position the cursor to point to the function requiring adjsutment 17_ Digital Day amp Night Color Camera E Camera Operation SETUP DC VIDEO Auto Iris Lens selection Select any function you LENS MANUAL gt Modes can be changed wish to operate by SHUTTER ESC d using the LEFT and using the UP and WHITE BAL ATW RIGHT buttons DOWN buttons BACKLIGHT OFF ne 2 i AGC LOW 4 e When using an auto iris lens the setting of the auto iris lens selection DNR LOW switch located on the back of the camera must be on DC or VIDEO TE Sop depending on the type of the lens which is being used 4 2 ENII Refer to the picture on page 13 e The brightness of the screen can be adjusted in DC mode The brightness can be adjusted within the range of 1 70 The optimum level of brightness for the user can be achieved by adjustment 3 Press the LEFT or RIGHT button if you wish to change mode e When the LEFT or RIGHT button is press2. F i la No 3 DY f No 1 Pn Connector No 4 Pin No 2 Pin 4 Replace the auto iris lens connection plug cover and take off the lens protection cap and then attach the auto iris lens to the camera by screwing it in clockwise 5 Insert the connection plug that is connected to the auto iris lens cable into the auto lens connector which is located on the back of the camera 6 Set the lens selection switch located on the back of the camera to DC or VIDEO depending on the type of auto iris lens which is being used 13 _ Digital Day amp Night Color Camera m Installation When using a CS Mount lens Take off the lens protection cap and attach the CS Mount lens to the camera by screwing it in clockwise CS mount adaptor When using a C Mount lens 1 Take off the lens protection cap and attach the C mount adaptor C mount adaptor Lens ea 2 Attach the C Mount lens to the camera by screwing it in clockwise C mount adaptor O Note e Use the specified lens connection parts as shown in the picture below The use of the wrong sized parts may cause damage to the inside of the camera or result in poor fitting e Use of a lens which is too heavy affects the balance of the camera and may cause a malfunction Please use a lens that weighs less than 450g e Select Av mode if possible when adjusting i on the automatic light control ALC of an auto lens
3. Saves all the setting menus and then exits Digital Day amp Night Color Camera 30 JY Digital Day amp Night Color Camera E Troubleshooting If there are problems with the camera operation check the tables below If the problem persists please contact the agent who supplied the product Problems Nothing appears on the screen The video image is not Clear The screen is dark e Please check if an appropriate power source to There is a problem with the camera operation The camera surface is too hot and black stripes appear on the screen Digital Day amp Night Color Camera N_32_ Troubleshooting e Check the power connection e Check the video signal line connection e Check and make sure that the auto lens switch is correctly set to DC or VIDEO depending on the type of lens attached e Make sure that the lens is clean Clean the lens with a clean lint free cloth or brush e Adjust the contrast control on the monitor e Make sure that the screen is not exposed directly to a bright light Re position the camera if necessary e Re adjust the back focus of the camera e Adjust the contrast control of the monitor e If there is an intermediate device set the750hm Hi z correctly and also check the connections e Check if an auto iris lens is being used and if necessary adjust the brightness level the camera complies with the manufacturer s standard requirement or if the voltage is fluctuat
4. Press the SET button after moving the cursor to CLR and all the letters will be erased If you want to correct a letter move the cursor to the arrow at MIRROR SHARPNESS RESET RETURN the bottom left of the screen and press SET Position the cursor above the letter you wish to correct and then move the cursor onto the letter you wish to choose and press the SET button Digital Day amp Night Color Camera 26_ ie Digital Day amp Night Color Camera E Camera Operation 5 When the camera ID is complete select a position for the name to be displayed 1 Move the cursor onto POS and then press the SET button Camera ID ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz 012345607609 ee Cline P O SEN a FRONT DOOR EN S lt Be f3 x i aya ff amp a lt gt to Locate hh SET 3 Select the position where the ID is E to be displayed by using the 4 directional FRONT DOOR buttons and then press the SET button 2 The ID will appear in the top left corner 6 Select END and press the SET button to complete ID input COLOR AUTO This camera has an IR Cut Filter and automatically changes to the appropriate mode dependant on lighting levels COLOR mode is selected during daylight and B W mode at night time ON _ The color mode is selected by default and the modes do not change automatically Digital Day amp Ni
5. PAL Model 1 120 ESC Auto control of the shutter speed is enabled When ESC mode is on the shutter speed is controlled automatically according to the brightness of the scene MANUAL The shutter speed can be controlled manually SETUP LENS MANUAL gt SHUTTER ESC WHITE BAL ATW BACKLIGHT OFF 3 Select MANUAL mode for manual shutter speed adjustment e Selectable speeds are from 1 60 to 1 120 000 sec NTSC and 1 50 to 1 120 000 sec PAL 4 Press the SET button when the settings are completed e While using the internal synchronous system if the shutter setting is on ESC and the camera is directly facing bright fluorescent lights the image on the screen can be adversely affected therefore choose the installation location carefully e When MANUAL mode is on the SENS UP function cannot be used WHITE BALANCE The screen colours can be adjusted using the WHITE BALANCE function 1 Position the cursor to point to WHITE BAL on the SETUP menu by using the UP and DOWN buttons 2 Select the mode you wish to adjust by pressing the LEFT or RIGHT buttons SETUP LENS MANUAL SHUTTER ESC gt WHITE BAL ATW BACKLIGHT OFF x Select one of the 3 modes below ATW Auto Tracking White Balance This mode can be used within the colour temperature range 1 800 K 10 500 K eg fluorescent light outdoor sodium vapour lamp etc AWC Auto White Balance Control Press
6. r he Abs CS mount lens 5 mm or less Use of PK mode may cause hunting E Connecting to a monitor Connect the video output terminal located on the back of the camera to the monitor 3 OSDEXTRA F C OUT N wee 5a DO SET TZVIN VIDEO O EMN CCD Camera Monitor The connection method varies depending on the type of monitor and accessories Please refer to the user s manual for each instrument e Turn off the power when connecting E Connecting to power Check the standard power requirement before connecting to power Dual Power Type AC 24V DC 12V AC 24V Class2 DC Power Type DC 12V 500mA Digital Day amp Night Color Camera ae By Digital Day amp Night Color Camera m Camera Operation E Menu SETUP menu LENS selection e MANUAL DC VVIDEO SHUTTER ESC e MANUAL FLK condition and speed control WHITE BALANCE control e ATW e AWC e MANUAL BACKLIGHT e OFF e LOW e MIDDLE Backlight compensation e HIGH AGC Auto Gain control e OFF e LOW e MIDDLE e HIGH DNR e OFF e LOW e MIDDLE Digital Noise Reduction e HIGH SENS UP Low illuminance OFF AUTO SPECIAL e CAMERA ID COLOR e SYNC e MOTION DETECTION e PRIVACY e MIRROR e SHARPNESS RESET e RETURN EXIT Digital Day amp Night Color Camera _16_ E Settings Settings can be made using the 5 buttons located on the back of the camera
7. Setting button SET button Used for the menu display This button can be used to confirm settings after changing the value of the selected function or Current conditions UP amp DOWN buttons Used for selecting items by moving the cursor up or down on the menu screen LEFT amp RIGHT buttons Used when changing item values by moving the cursor to the left or right on the menu screen Power input terminal Connects to the power appropriate to each power requirement 11 _ Digital Day amp Night Color Camera D igital Day amp Night Color Camera E Installation E Lens Lenses are sold separately Lenses such as auto iris lens CS Mount lens and C Mount lens can be used 3 Use of the DC auto iris lens is recommended to achieve the best results for operating this product effectively e Keep the lens clean e Any foreign objects and fingermarks on the lens can cause inferior image quality in low light level conditions When using an auto iris lens 1 Peel off about 8mm of the outer skin of the auto iris lens cable approx 8mm o 2 Peel off about 2mm of the outer skin of the insulated conductor inside the lens cable approx 2mm Installation E 3 Remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug LENS VIEO No 1 Pin Red power No 2 Pin Damping NC No 3 Pin Drive White video signal Bac GND EZ Lens cable a
8. TV Lines Video Output 1 0V 0175 Video 0 714Vp p Sync 0 286Vp p 1 0Vp 0175 Video 0 7 Vo p Sync 0 3 Vp p SN Y signal 50dB AGC Off Min Illumination 0 3Lux F1 2 Color 0 1Lux F1 2 B W 0 002Lux Sens up L Color ON AUTO z Gain Control OFF LOW MIDDLE HIGH T White Balance ATW AWC MANUAL 1 800 K 10 500 K i Electronic Shutter Speed AUTO MANUAL 1 60 1 120 000 AUTO MANUAL 1 50 1 120 000 C SensUp OFF AUTO L 0 S D Built in Motion Detection ON OFF 4 Programmable Zone DNR OFF LOW MIDDLE HIGH Noise Reduction Mirror Built in Horizontal Image Inversion Privacy Function ON OFF 4 Programmable Zone Iris Control DC VIDEO Lens Mount C CS Mount Screw Lock Operating Temperature Humidity 10 C 50 C 30 90 RH Weight 340g Digital Day amp Night Color Camera N _34_ CLINTON Electronics CLINTON Electronics Clinton Electronics Corp 1 800 447 3306 Sales 6701 Clinton Road 1 800 549 6393 Support www clintonelectronics com Loves Park IL 61111 1 815 633 8712 Fax
9. an object s DOWN LEFT or RIGHT button movement by sensing disparity of outline and level of brightness and color MIRROR e Please press the SET button OFF MOTION DETECTION mode is cancelled PON PE A A ZONA AJE ave Or ON Any motion in the selected areas is observed OFF Cancels the inversion e Please select the area you wish to observe from the 4 areas in AREA SEL mode Please select ON mode for the chosen area e Please adjust the size of the area to be observed by using the UP DOWN LEFT or RIGHT button MIRROR ON MIRROR OFF MOTION SHARPNESS The outline of the video image becomes cleaner and Eo AREAL more distinctive as the level of SHARPNESS increases If the level goes up excessively however it may affect the video image and generate noise Press SET to Return e Please press the SET button SHARPNESS Please press the SET button to save the changes and complete the setting PRIVACY This mode conceals the areas you do not wish to appear on the screen OFF Cancels the PRIVACY mode ON Operates the PRIVACY mode e Please press the SET button gt LEVEL Junfunmninn 8 The available range of level is 0 31 PRIVACY rr RESET Returns to the level which was set by the manufacturer for shipment ce fee RETURN Saves the SPECIAL menu and returns to the SETUP menu EXIT Press SET to Return
10. is normal Digital Day amp Night Color Camera 24 i Digital Day amp Night Color Camera m Camera Operation SPECIAL 1 Position the cursor to point to SPECIAL on the SETUP menu by using 3 Press the SET button the UP and DOWN buttons 2 Select the mode required by pressing the UP or DOWN button Camera ID ABCDEFGHIJUKLM NOPQRSTUVWXYZ SPECIAL abcdefghijklm nopgqrstuvwxyzZ gt CAMERA ID OFF LLST COLOR ON gt CUR POS END SYNC INT oo MOTION DET OFF PRIVACY OFF 4 Up to 15 characters can be used for the camera ID MIRROR OFF Move the cursor to the letter required by using the UP and DOWN SHARPNESS ON 4 button RESET RETURN Camera ID A ABCDEFGHIJKLM NOPQRSTUVWXYZ CAMERA ID If an ID is input this camera ID appears on the monitor ede cen ig and recorded footage nopgrstuvwxyz 1 Position the cursor to point to CAMERA ID by using the UP or ae oa oe a DOWN button perce eos 2 Select ON by pressing the LEFT or RIGHT button O Note e If OFF is selected the ID does not SPECIAL appear on the monitor even if it has been input Select an ID from A B Y Z a b y z 0 1 8 9 by using the UP DOWN LEFT and RIGHT buttons Lock in the characters by using the SET button e Once locked in the cursor moves to the next space in the ID gt CAMERA ID Repeat the above steps until the ID is complete COLOR Q 9 SYNC MOTION DET PRIVACY If the wrong name has been input
11. CLINTON Electronics High Resolution Color Day Night Box Camera CE CC115 W CLINTON Electronics Clinton Electronics Corp 1 800 447 3306 Sales 6701 Clinton Road 1 800 549 6393 Support www clintonelectronics com Loves Park IL 61111 1 815 633 8712 Fax CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules amp CE Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to rad
12. The amount of low illuminance noise If the camera is installed on an inappropriate surface it may fall appropriate for daytime or night time has been significantly reduced and the and cause injury conditions The COLOR mode operates in signal to noise ratio S N ratio as well as l daytime conditions to provide optimum horizontal resolution have been improved colors and BW mode operates in night resulting in clear and sharp images time conditions to enhance the definition displayed even in low light Do not hold plug with wet hands of the image It could cause an electric shock AA Dd J Electronic IRIS 4 Controlled by OSD Menu ae PTN Do not dis assemble the camera The electronic IRIS function enables The camara tunctions are controlled by It may result in an electric shock or other hazards continuous automatic control of the selecting text displayed on the monitor shutter between 1 60 1 120 000 seconds screen ETY Sdi Do not use the camera close to a gas or oil leak gt PR VACY Function Additional Functions It may result in a fire or other hazards A a A gt The PRIVACY function conceals the SENS UP MOTION DETECTION areas not required to appear on MIRROR SHARPNESS and SYNC the image INT LL functions are also available 2 VIDEO DC Drive Lens S gt b i a U The video drive lens and the DC drive lens can be selected by the touch of a switch Digital Day amp Night Color Camera V2 Sy Digital Day amp Night C
13. ed available values and modes are displayed in order Please keep pressing the button until you get to the mode you wish to operate 4 Select EXIT and then press the SET button to finish the setting Q If appears at the mode selected it means that there is a sub menu which can be selected by pressing the SET button LENS PBRIGHTNESS osm 25 Press SET to Return lf appears at the mode item it means that there are no modes available for selection LENS selection MANUAL Manual Lens selection This function is used to adjust the brightness of the screen 3 Press the SET button if you wish to return to the previous menu 1 When the SETUP menu is displayed on the screen position the cursor to point to LENS by using the UP and DOWN buttons 2 Select the type of the lens setting to use by pressing the LEFT or RIGHT button SETUP gt LENS DC SHUTTER TAg WHITE BAL ATW BACKLIGHT OFF Digital Day amp Night Color Camera 18_ 3 Digital Day amp Night Color Camera m Camera Operation SHUTTER condition and speed control Auto or manual control can be selected 1 When the SETUP menu is on the screen position the cursor to point to SHUTTER by using the UP and DOWN buttons 2 Select the shutter mode by pressing the LEFT or RIGHT button FLK Select FLK mode when flickering occurs on the screen due to an imbalance between illumination and frequency NTSC Model 1 100
14. ena Lene protecion cap Cover the lens when not using it CS Mount lens adaptor Attach the CS Mount lens here 5 INSTRUCTION GUIDE Back Focus clamp screw Loosen the clamp screw with a screwdriver before adjusting the Back Focal length Digital Day amp Night Color Camera ee 7 Digital Day amp Night Color Camera E Names and Functions of Parts Bottom 4 Mounting bracket screw hole Use the screw hole when fixing the camera onto the mounting bracket Please use the clamp screw as specified in the picture 1 4 20 UNC 20 THREAD L 4 5mm 0 2mm ISO standard or 0 197 ASA standard x The mounting bracket can be separated and attached on the top of the camera please do not tighten the screw to a depth of more than 5mm otherwise serious damage can occur to the inside of the camera Digital Day amp Night Color Camera lt 0 Names and Functions of Parts E Back oe Hs jae DAVIN VIDEO 12V IN Wj Auto iris lens connector This is the connection terminal for the auto iris lens Auto iris lens selection switch Change the mode to DC or VIDEO depending on the type of auto iris lens being used OSD Extra Connects to the remote controller option when you want to install remotely Video output terminal Sends video signals and connects to the video input terminal of the monitor Power lamp Lights up when the correct power is supplied to the camera
15. ght Color Camera 28_ When the AGC is turned off COLOR does not operate When an infrared light is used there may be a problem with focusing SYNC Two sychronisation modes are available INTERNAL and EXTERNAL LINE LOCK In LINE LOCK mode it synchronises the video signal between cameras without a synchronous generator The line lock synchronisation is only used in areas of 60Hz NTSC Models 50Hz PAL Models INT Internal synchronisation LL External line lock synchronisation If QLGs selected it can be adjusted to the desired phase Press the SET button Adjust to the desired phase from 0 to 359 Press SET to Return Q F When the mains frequency is 50Hz the line lock mode NTSC Models cannot be used When the mains frequency is 60Hz the line lock mode PAL Models cannot be used GyncGnode is fixed to NTGn DC12V input power 29 _ Digital Day amp Night Color Camera E Camera Operation MOTION DETECTION e Please select the area you do not wish to appear from the 4 areas in This product has a feature that allows you to observe movements of objects AREA SEL mode in 4 different areas on the screen and the words MOTION DETECTED e Please select ON mode for the chosen area appear on the screen when movement is detected hence a single individual e Please adjust the size of the area to be concealed by using the UP can conduct supervision efficiently The camera detects
16. he LEFT or RIGHT button As the 1 Position the cursor to point to BACKLIGHT on the SETUP menu by level of gain increases the screen gets brighter but the level of noise will using the UP and DOWN buttons also increase 2 Select the value required by pressing the LEFT or RIGHT button HIGH _ The gain varies between the range of 6dB 420B MIDDLE The gain varies between the range of 6dB 30dB SETUP LOW _ Thegain varies between the range of 6dB 18cB E OAN OFF The gain is fixed at 6dB SHUTTER ESC 4 WHITE BAL ATW Ea gt BACKLIGHT OFF AGC LOW 4 LENS MANUAL DNR LOW SHUTTER ESC WHITE BAL ATW BACKLIGHT OFF O HIGH _ The gain increases from OdB up to 42cB 4 ao TNN MIDDLE The gain increases from OdB up to 30dB ane ome LOW The gain increases from OdB up to 18dB SPECIAL lt i OFF BACKLIGHT function does not operate EXIT BACKLIGHT OFF Digital Day amp Night Color Camera N_22_ _23 _ Digital Day amp Night Color Camera m Camera Operation DNR Digital Noise Reduction The level of background noise in low light decreases automatically as the 1 Position the arrow to point to SENS UP on the SETUP menu by using level of gain changes the UP and DOWN buttons 1 Position the cursor to point to DNR on the SETUP menu by using the 2 Select the value required by pressing the LEFT or RIGHT button UP and DOWN buttons AUTO Lowl
17. ight level automatic mode 2 Select the value required by pressing the LEFT or RIGHT button OFF The function does not operate SETUP r w LENS MANUAL 2 SHUTTER ESC 4i e When SHUTTER is in the manual or flk mode SENS UP does not operate WHITE BAL ATW e When AGC is turned off SENS UP does not operate BACKLIGHT OFF AGC LOW 4 SETUP gt DNR LOW SENS UP OFF LENS MANUAL SPECIAL SHUTTER ESC 4 WHITE BAL ATW OFF There is no reduction in noise level ee Oe a AGC LOW 4 LOW _ There Is a small reduction in noise level with almost no DNR LOW ghost image gt SENS UP OFF MIDDLE The most effective mode There is a sufficient reduction SPECIAL 4 in noise levels without causing significant ghosting EXIT HIGH The level of noise is reduced greatly however there is an increase in ghosting 3 Press the SET button when all the settings are complete When AGC is turned off DNR does not operate e The maximum storage magnification in low light level movement situations can be adjusted by pressing the SET button in AUTO mode X2 X128 e As the magnification increases the screen gets brighter however the SENS Ue after image also increases SENS UP helps maintain a bright clear screen image by automatically e If storage magnification is increased while SENS UP is operational it detecting changes in the level of light in low light level conditions may Cause noise and spots may appear this
18. ing Check for ground loops Problems The MOTION DETECTION function is not working Colors are not quite right The screen is flickering L L mode isn t able to be selected L L mode is not available COLOR mode is not working SENS UP function is not working Troubleshooting e Check if MOTION DETECTION mode is turned on e Check the setting of the MD AREA e Check the WHITE BAL setting e Check if the camera is facing directly into sunlight or fluorescent light e Check if an auto iris lens is being used e Check the connection of the lens connector cable e Have you connected your camera to DC power source Connect it to AC power source e Check the frequency of power supply 60Hz for NTSC 50Hz for PAL e Check if the AGC menu is set to the OFF position e Check if the AGC menu is set to the OFF position e Check if the SHUTTER menu is set to MANUAL mode 33_ Digital Day amp Night Color Camera Specifications MEMO m ITEM NTSC PAL AC24V DC12V DC12V AC24V DC12V DC12V Power Source T70mA AC24V 260mA DC12V 160mA 170mA AC24V 260mA DC12V 160mA Total Pixels 811 H x 508 V 795 H x 596 V rs Effective Pixels 768 H x 494 V 752 H x 582 V D Size 1 3 inch interline transfer CCD Scanning System 2 1 Interlace Synchronization INT LL Selectable INT LL Selectable 2 0 359 Adjustable NT c as9 Aqjustable Horizontal 15 625 KHz Vertical 50 00 Hz Resolution 540
19. io communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment CAUTION To prevent electric shock and risk of fire hazards Do NOT use power sources other than those specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes Digital Day amp Night Color Camera E Features Warning E mew Eve The camera requires periodic inspection Horizontal Resolution of 540 TV 2 High Sensitivity Contact an authorised technician to carry out the inspection f Lines Laa an Clear image quality has been achieved by The built in high sensitivity SONY COLOR employing a SONY CCD with 410 000 CCD enables a clear image even in Stop using your camera when you find it malfunctioning effective pixels which provides a 0 3Lux 0 1Lux B W or as low as 0 002Lux p horizontal resolution of 540 TV lines with SENS UP If the camera emits smoke or is unusually hot for a long period a fire may be caused DAY amp NIGHT ae i 3 DNR Digital Noise Reduction Sr ee ee eee on E Do not Install the camera on a surface that can not support it matically selects the mode that is
20. ly careful to provide ventilation when operating under high temperatures Do not install the camera under unstable lighting conditions LAE ZB 4 ay DA 5 D A Severe lighting change or flicker can cause the camera to work improperly Digital Day amp Night Color Camera N Do not install or use the camera in an environment where the humidity is high 9 Ox amp aC ial ee S TAE A Va It can cause the image quality to be poor Do not touch the front lens of the camera This is one of the most important parts of the camera Be careful not to leave fingerprints on the lens cover Do not drop the camera or subject Never keep the camera pointed it to physical shocks directly at strong light PY Lady ry 5 5 ge It can cause malfunctions to occur It can damage the CCD Do not expose the camera to rain Do not expose the camera to or spill beverage on it radioactivity rx amp If it gets wet wipe it dry immediately If exposed to radioactivity the CCD Liquids can contain minerals that will fail corrode the electronic components If the camera is exposed to spotlight or object reflecting strong light smear or blooming may occur e Please check that the power satisfies the normal specification before connecting the camera _ Digital Day amp Night Color Camera E Components Names and Functions of Parts E Front N 4 C MOUNT ADAPTOR e
21. olor Camera E Contents Features sting ioblaei Inui ah E E boat ai boeu beards 2 Camera Operation ne E pace E A E A cee oe 16 E Menu ooo EEEE 16 Warnings and Precautions ae oE E E E EA E O EE E 3 E Settings Cakes baat E vaseee rig peaanee tite cea bean iahaaien 17 Components AORTO EIEE EEI T EEEE a 8 e LENS selection aa E A R R E an A aaa BO e SHUTTER condition and speed control ee 20 Names and Functions of Parts EEPE SETT EEE E ESEE EE S nore anerateed 9 lt WHITE BALANCE control N E Front ee g BLC Back Light Compensation L 99 E Bottom r NE T 4p aes E A E E E E E EAA EE AE ANE asap 10 AGC Auto Gain Control L 23 Oo Back U S a n e 26 aygotug E E anerdan gue a E E aye tee g eng E E A arenes ead A E E 11 z DNR Digital Noise Reduction EE ESERE EST 24 Installation ere a a psa eat ae E a N e 12 i SENS UP OO 24 SPECIAL are sedate E Let bake Ree epee eae eng aoa ee pata pebedead er ene ates 26 aS ces got eco eae nec EEE 12 Using auto iris Using C CS mount lens f Troubleshooting sees a Sede cana Beene ae tas ees eas ween 32 A Connecting tO AMONIO eors anen Aaa 15 E Connecting TO DOWN secs emacrserriviamreamesstistieesigi ys reiyanieniedp eae 15 Speci nn 34 Digital Day amp Night Color Camera 4 y Digital Day amp Night Color Camera E Precautions Do not install the camera in extreme temperature conditions hi Qe Only use the camera under conditions where temperatures are between 10 C and 50 C Be especial
22. the SET button while the camera is directed at a piece of white paper to obtain the optimum state under current illumination If the environment including the light source changes the white balance will need to be adjusted again MANUAL The manual adjustment mode enables finer adjustment Select ATW or AWC first then change to manual adjustment mode and press the SET button Set the appropriate colour temperature then increase decrease the red and blue colour values and monitor the color changes of the object Q 9 e Under the following conditions the WHITE BALANCE function may not operate properly In such cases please select the AWC mode When the object s surroundings have a very high colour temperature eg a clear sky and sunset When the object s surroundings are dark If the camera directly faces a fluorescent light or is installed in a place where there are considerable changes in illumination the WHITE BALANCE function may become unstable Digital Day amp Night Color Camera _20_ _21_ Digital Day amp Night Color Camera m Camera Operation BACKLIGHT Back Light Compensation When there is a strong backlight behind the object clear images of the background as well as the object can still be obtained by using the BACKLIGHT function AGC Auto Gain Control 1 Position the cursor to point to AGC on the SETUP menu by using the UP and DOWN buttons 2 Select the value required by pressing t
Download Pdf Manuals
Related Search