the user manual - Easy
Contents
1. ARBORIST amp LANDSCAPE Models All EASY LIFT Arborist amp Landscape models now have the EASY GRIP 1 strap for handheld implements To attach simply wrap around the handle of the implement and fasten with the velcro When ready to use just attach the carabiner to the ring and get to work ARBORIST Model Only The EASY LIFT Arborist model will also have the EASY GRIP 2 strap for use with extended power pole saws To attach find the balance point of the saw then wrap around the shaft of the power pole saw at that point and fasten with the velcro When extending or retracting the shaft make sure to move the EASY GRIP by sliding to the new balance point NEW in 20112. and mounting bracket in the new position i e A A or C C DO NOT attempt to mismatch positions like A B or C B STEP 4 Reassemble with bolts washers amp nuts Place gas spring in position by firmly pressing each end onto mounting bracket until it snaps in place Make sure the piston rod of the gas spring is on the bottom and cylinder on top NOTE ARBORIST MODELS MUST BE REASSEMBLED WITH INNER GAS SPRING 752800 amp OUTER GAS SPRING 1424EY DO NOT SWITCH Page 5 PREPARE THE CORD e Set the slide toggle near the end of the boom so the rope extends downward as far as possible Make sure the snap hook is clipped on the eyebolt Wier a Aes Ce B STRAPPING IN 2 1 Hold the EASY LIFT Harness at the connector tube with one hand 2 2 Position the backpack frame on your back while sliding on arm in the shoulder strap 2 3 Release hand from the connector tube and place remaining arm in strap 2 4 Connect waist strap amp sternum strap Tighten waist shoulder amp sternum straps ATE AA ee inet Te a ee A mgm An PAm a 1nd ae FH L A Th JS Se wT ry D V ET ee e ey V M saal wri a sU irm l iil M An 1 art em n AO D nr e a id 2 1 ATTACHMENT amp ADJUSTMENT 3 1 Grasp the cord and pull the boom down with one hand 2 3 2 4 3 2 Remo
3. EASY LIFT HARNESS OPERATOR S MANUAL LANDSCAPE amp ARBORIST MODELS US PATENT 6 481 108 D EASY LIFT HARNESS LANDSCAPE amp ARBORIST MODELS ATTENTION The EASY LIFT Harness is intended for PROFESSIONAL USE ONLY The EASY LIFT Harness is an extraordinary device with unique operating characteristics It is highly recommended that the owner and operators of this equipment read and follow ALL instructions in this manual Make all adjustments and become familiar with the device BEFORE using it Best results will depend on e Proper fit e Proper adjustment e Proper maintenance e Safe operation The EASY LIFT Harness is the finest full range lifting harness developed for the Landscape amp Arborist industries TAKE CARE USE IT AND ENJOY EASY LIFT PRODUCTS INTERNATIONAL INC Page 1 SAFETY FIRST Safety is the first and most important rule when operating this equipment The EASY LIFT Harness is designed to make work easier and less strenuous while working safely on the ground Please read and follow these simple guidelines when using the EASY LIFT Harness to ensure your Safety SAFETY GUIDELINES e ALWAYS wear protective eyewear headgear amp clothing e ALWAYS test the operation of your EASY LIFT Harness before starting your implement e ALWAYS maintain two handed control of the implement after it is connected to the harness e ALWAYS shut off the implement and wait for it to st
4. chaser only to be free of defects in materials and workmanship for one year from date of purchase without any additional charge Incidental and consequential damages due to normal wear amp use are specifically excluded from coverage under this warranty WARRANTY POLICY Replacement parts are available at your EASY LIFT Harness dealer with proof of purchase LIMITATIONS This warranty does not cover defects resulting from normal wear and tear including chips scratches abrasions discoloration or fading due to usage or exposure to sunlight accidents damage during shipping modifications unauthorized use or repair neglect misuse abuse failure to follow instructions for care and maintenance fire flood and acts of God If your problem is not covered by this warranty call Technical Support 941 485 0262 or toll free 866 231 0778 EASY LIFT PRODUCTS INTERNATIONAL Page 8 ALL Models Shown here are two new additions to the EASY LIFT Harness All Models On the right shoulder strap you will see the Carabiner Safety Strap This keeps the carabiner and cord out of your way when putting on and taking off the harness You will need to draw the toggle all the way to the end of the boom in order to attach the carabiner to the safety strap Also shown here is the new carabiner There s no explanation needed It s bigger better and easier to use The NEW Carabiner and Carabiner Safety Strap
5. h the bolts provided When the lower mast is properly in place it should be at a slight angle as shown in the picture below DO NOT over tighten the nuts as you may crush the tubing STEP 2 Connect the boom amp upper mast with the quick release pin When properly connected the pin should pass through the yoke amp the brass bushing on the boom Page 3 STEP 3 Connect the upper amp lower assembly with the connector tube and bolt provided Finger tighten the nut and then tighten only 1 4 turn with a wrench DO NOT over tighten as you may crack the connector tube YOUR EASY LIFT HARNESS IS NOW COMPLETE There are 3 force ranges provided with each EASY LIFT Harness Each harness is set at the middle or B B position You may want to keep this position as it is the best for most implements Moving the gas spring to the C C position will slightly increase the lifting force while moving to the A A position will slightly decrease the lifting force To make this adjustment please follow these instructions STEP 1 Remove the gas spring by sliding a small flat screwdriver blade under the retention spring located at both ends of the gas spring and lift Page 4 STEP 2 Remove the spring mounting brackets with a wrench and socket as shown for ARBORIST models you will need to remove the outer gas spring amp brackets first and then the inner gas spring amp brackets STEP 3 Place the spring
6. op before disconnecting from the harness e NEVER run when using the EASY LIFT Harness e NEVER operate the EASY LIFT Harness near electrical wires and other overhead obstacles that may come in contact with the upper assembly e NEVER use the EASY LIFT Harness on steep slopes ladders chairs stools lifts or in any condition where falling is likely to occur e NEVER fill the gas tank of your implement while connected to the EASY LIFT Harness This device is intended for outdoor use only Be familiar with your equipment and make all adjustments to the backrest shoulder straps waist adjustments and sternum strap before attaching an implement Make all balance point and lifting force adjustments to your implement before operation If your harness becomes damaged DO NOT attempt to straighten any kinked or bent parts DO NOT modify or alter the equipment in any way Call EASY LIFT Products International or your local dealer for information on replacement parts or adjustments EASY LIFT PRODUCTS INTERNATIONAL 1 866 231 0778 M F 8 00AM 5 00PM EST USA www easyliftharness com dealers Page 2 The EASY LIFT Harness has 3 main parts to assemble 1 The upper assembly 2 The lower mast 3 The backpack frame Assembly of your EASY LIFT Harness is simple and should be done as follows consists of the boom the upper mast amp the gas spring STEP 1 Fasten the lower mast to the backpack frame wit
7. ve the snap hook from the eyebolt and attach to the loop at the end of the cord 3 3 Set the toggle to the desired operation position 3 4 Attach the implement to the snap hook Note Readjust the toggle as necessary so you are able to use the implement as low or high as necessary WARNING DO NOT set the toggle position so that the boom hits your head Always maintain control of the implement with both hands Never set the force range so the implement lifts on its own Page 6 ARBORIST MODEL ONLY The ARBORIST Model has two gas springs and is designed specifically for extended power pole saws If you wish to convert your ARBORIST Model to a LANDSCAPE Model for use with lighter implements you will need to remove the outer gas spring as follows Remove the outer gas spring by sliding a small flat blade screwdriver under the retention spring at both ends of the gas spring and lift ARBORIST MODEL LANDSCAPE MODEL With only the inner gas spring remaining you now have a LANDSCAPE Model EASY LIFT Harness EASY LIFT PRODUCTS INTERNATIONAL COPYRIGHT 2010 Page 7 WARRANTY INFORMATION gt OO m yE 1 YEAR LIMITED WARRANTY WARRANTY This is the only warranty that applies to this product and it sets forth all the responsibilities of EASY LIFT Products International regarding this product There is no other warranty than that described herein The EASY LIFT Product is warranted to the original pur
Download Pdf Manuals
Related Search